|
| 1 | SHEDULE – I Location :- KAVARATTIItem No.1 Breaking and removing the concrete to form duct of 15cmx10cm for laying power cable/Electrical wire through PVC Pipe, covering the duct after laying the cable with cement mortor and dismantling cement concrete 1:3:6 or 1:2:4 richer mix & disposing the debris etc., and providing R.C.C. 1:1½ :3 (one cement, one and half sand and three granite stone jelly 20mm down size) for column, beam, slab etc., including cost of all labour charge, cost of minor tools & plants, cost of materials etc., complete |
| 2 | Item No.2 Supply & Laying of following sizes of PVC / XLPE insulated PVC inner sheeted unarmoured aluminum power cable of 1.10 KV grade under ground cable of reputed make like : Havells/ Unicab/ Suncab/ Toshicab/ Polycab confirms to IS 1554 / 7098 through DWC pipe of suitable size duct provided as per the instruction of EIC, including cost of all labour charges, cost of minor tools, applicable GST and LWC cost of UG cables, DWC pipes, all materials etc., complete. |
| 3 | 70 sqmm x 3½ core |
| 4 | 50 sqmm x 3½ core |
| 5 | 16 sqmm x 4 core |
| 6 | Item No.3 Wiring for circuit / sub main wiring along with earthwire with the following size of FR PVC insulated multistrand copper conductor cable in surface / recessed PVC conduit as required. (CPWD - 1.14.4) |
| 7 | 2 x 6 sqmm along with earth wire 1 x 6 sqmm. |
| 8 | Item No.4 Dismantling and removing the R.C.C. Lamp Post of light 5.50 meter from the approach of jetty by providing necessary scaffoldings up to the required hight, transporting the debries with in a lead of 2 Kms, disposing the same without causing hindrance to the crafts and people utilizing the jetty as directed by the EIC, including cost of all labour charges, tools and plants, transportation charges etc; complete. |
| 9 | Item No.5 Supplying, Erecting and Commissioning of CNC filament wound Glass Reinforced Polymer (GRP) street lighting poles (Colour: Silver Grey) of anchor type with base plate of 250X250 mm , shaft length 6000 mm, top/bottom OD dia 114/170 ?5mm apprx. average thickness 6 mm with integral/external junction box with 4 terminals of 6 sq. mm & 6 AMP SP MCB (IP65), GRP Single side arm bracket of 1000 mm length with SS JB Clamp-D 1075 including wiring with 3 X 1.5 sqmm PVC insulated multistrad copper wire from junction box to lamp set etc complete of SUMIP/ BAJAJ/SATYAM - Make or Equivalent in other reputed make including GST, Labour cess, cost of all materials of GRP lamp post, single arm, base plate and labour charges etc complete including cost of laying PCC pedestal of 0.40X0.40X0.75 Mtr(WXBXH) |
| 10 | Item No.6 Supply, installation, testing and commissioning of LED street light luminaire / Flood lights as per the following specification on the lamp post / high mast light towers provided, giving connection with 1.5 sqmm PVC insulated copper wire etc as required but including cost of fittings, GST, Labour Cess, cost of all materials, labour charges, scaffolding charges and minor tools etc complete. |
| 11 | 90 watt LED street light luminaire - Make - Bajaj , Model - EDGE, BRTFG 90 W LED 1(or) Equalent in other reputed make like - Havells / Crompton / Philips. LED streetlight shall be made up of pressure die cast housing with toughned glass and individual LEDs with secondary optics and IP66 protection. |
| 12 | 150 watt (85 lumen/watt) rating LED Flood light fitting of reputed make like Crompon / Bajaj / Havells on the top of the light carriage of the highmast lighting tower including cost of all materials and all labour charges etc. complete LED streetlight shall be made up of pressure die cast housing with toughned glass and individual LEDs with secondary optics and IP66 protection. (for existing Highmast) |
| 13 | Item No.7 Supply, installation, testing and commssioning of outdoor type floor mounted power pillar box of 1200 x 900 x 450 mm size distributin pillar box (As per drawing) made of SINTEX foam PVC sheet of 8 mm thick non extenable type with 4 strip Aluminium busbar suitable for LT 3 phase, 415 V, 100Amps capacity with twin door open with locking arrangement in front side and have the facility to accommadate various size of electrical items and out side pasted with standard size of danger plate as required. The rate including cost of all materials and labour charges, minor tools and plants, GST, LWC and providing CC pedestal as per drawing etc. complete. |
| 14 | Item No.8 Supplying and fixing following 6/8 way, single pole and neutral, sheet steel, MCB distribution board, 240/415 volts, 32/40 Amps on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) (2.3.2) including cost of all materials, GST, Labour Cess and minor tools etc complete. |
| 15 | Item No.9 Supplying and fixing 40/63 Amps rating, four pole, (three phase and neutral) MCB 415 volts /residual current circuit breaker (RCCB) having a sensitivity current 30 milli amperes in the existing MCB DB complete with connections, testing and commissioning etc. as required including cost of all materials, GST, Labour Cess and minor tools etc complete. (2.15.3) |
| 16 | Item No.10 Providing and fixing following rating and breaking capacity MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel boardincluding drilling holes in cubicle panel, making connections, etc. as required including cost of all materials, GST, Labour Cess and minor tools etc complete. (2.2.1 & 4) |
| 17 | 100 Amps TPN, 16 KA Breaking capacity |
| 18 | 200 Amps TPN, 16 KA Breaking capacity |
| 19 | Item No.11 Supplying and laying of 12 SWG bare copper wire along with the pipes routed with UG cables, termination at all the cable end terminations. Giving connection with the existing earthing loop in control panel including cost of all materials and labour charges etc. complete. |
| 20 | Item No.12 Supplying, fixing, testing and commissioning SS 316/Poly-Carbide material surface mounting Digital Timer of 230 Volt single phase supply with 14 – 20 Amps direct load capacity from NO/NC terminal with IP - 65 enclosure daily programmable with suitable NO + NC auxilary contacts control voltage 230/220V AC of reputed make like L&T, Legrand, Havells etc. including cost of all materials and labour charges etc complete. |
| 21 | Item No.13 Supply of 12 Mtr high mast area lighting system with following accessories at Kavaratti including all taxes, packing and forwarding charges & cost of transportation charges from mainland to Kavaratti island. (a) Mast shaft shall be in one/two section hot dip galvanised mast shaft suitable for wind velocity as per IS 875, accessories like head frame, steel wire rope 5mm dia( 7/19 construction), trailing cable, double drum winch, galvanised lantern carriage arrangements suitable for 6 luminaries symmetrically and its control gear boxes and lighting finial. The integral power tool installes inside the base compartment for its operation. (b) Foundation bolt manufactured of special steel along with nuts, washers, anchor plates and templates, required for the mast. (c) Supply of 6 nos. 150W LED flood light fitting with all accessories. Luminaries housing components to be extrude aluminum, with high performance heat sinks, luminaries provided with heat resistant toughened glass, extruded aluminum control gear compartment, colour temp – 5700 K +/- 300 K, LEDs are provided with secondary lens optics to get optimum optical performance. Internal protection against lightening, surge voltage, open/short circuit protection. Power factor>95%, System Lumen package shall be as per IESNA LM79-80,IP66 protection, luminaries is provided with with a mounting bracket fixe on die cast aluminum end plates for aiming adjustment. Make: Bajaj/ Crompton/ Havells or Equivalent (d) Supply of LED aviation obstruction light (e) Control panel housing 32 Amp TPN MCB incomer, single dial timer contactor circuit for the automatic control of luminaries outgoing terminals and control circuit for the power tool motor etc., complete including all taxes and packaging and forwarding charges. (f) Providing power supply line to high mast including cost of suitable cable & other materials, all labour charges, etc., complete (g) Providing founadtion structure for installing the high mast lighting system at site as per the standard drawing as directed by the Engineer in Charge etc., including cost of all materials and labour charges etc., complete. (h) Erection of the high mast lighting system with the help of the suitable equipments at the location as directed by the Engineer in Charge, installation of the control panel and wiring the luminaries including cost of all wiring materials and cost of all labour charges etc. complete. |
| 22 | SHEDULE – II Location:- AGATTI Item No.1 Breaking and removing the concrete to form duct of 15cmx10cm for laying power cable/Electrical wire through PVC Pipe, covering the duct after laying the cable with cement mortor and dismantling cement concrete 1:3:6 or 1:2:4 richer mix & disposing the debris etc., and providing R.C.C. 1:1½ :3 (one cement, one and half sand and three granite stone jelly 20mm down size) for column, beam, slab etc., including cost of all labour charge, cost of minor tools & plants, cost of materials etc., complete |
| 23 | Item No.2 Supply & Laying of following sizes of PVC / XLPE insulated PVC inner sheeted unarmoured aluminum power cable of 1.10 KV grade under ground cable of reputed make like : Havells/ Unicab/ Suncab/ Toshicab/ Polycab confirms to IS 1554 / 7098 through DWC pipe of suitable size duct provided as per the instruction of EIC, including cost of all labour charges, cost of minor tools, applicable GST and LWC cost of UG cables, DWC pipes, all materials etc., complete. |
| 24 | 16 sqmm x 4 core |
| 25 | Item No.3 Wiring for circuit / sub main wiring along with earthwire with the following size of FR PVC insulated multistrand copper conductor cable in surface / recessed PVC conduit as required. (CPWD - 1.14.4) |
| 26 | 2 x 6 sqmm along with earth wire 1 x 6 sqmm. |
| 27 | Item No.4 Dismantling and removing the R.C.C. Lamp Post of light 5.50 meter from the approach of jetty by providing necessary scaffoldings up to the required hight, transporting the debries with in a lead of 2 Kms, disposing the same without causing hindrance to the crafts and people utilizing the jetty as directed by the EIC, including cost of all labour charges, tools and plants, transportation charges etc; complete. |
| 28 | Item No.5 Supplying, Erection and Commissioning of CNC filament wound Glass Reinforced Polymer (GRP) street lighting poles (Colour: Silver Grey) of anchor type with base plate of 250X250 mm , shaft length 6000 mm, top/bottom OD dia 114/170 ?5mm apprx. average thickness 6 mm with integral/external junction box with 4 terminals of 6 sq. mm & 6 AMP SP MCB (IP65), GRP Single side arm bracket of 1000 mm length with SS JB Clamp-D 1075 including wiring with 3 X 1.5 sqmm PVC insulated multistrad copper wire from junction box to lamp set etc complete of SUMIP/ BAJAJ/SATYAM - Make or Equivalent in other reputed make including GST, Labour cess, cost of all materials of GRP lamp post, single arm, base plate and labour charges etc complete including cost of laying PCC pedastal of 0.40X0.40X0.75 Mtr(WXBXH) |
| 29 | Item No.6 Supply, installation, testing and commissioning of LED street light luminaire / Flood lights as per the following specification on the lamp post / high mast light towers provided, giving connection with 1.5 sqmm PVC insulated copper wire etc as required but including cost of fittings, GST, Labour Cess, cost of all materials, labour charges, scaffolding charges and minor tools etc complete. |
| 30 | 90 watt LED street light luminaire - Make - Bajaj , Model - EDGE, BRTFG 90 W LED 1(or) Equalent in other reputed make like - Havells / Crompton / Philips. LED streetlight shall be made up of pressure die cast housing with toughned glass and individual LEDs with secondary optics and IP66 protection. |
| 31 | Item No.7 Supplying and laying of 12 SWG bare copper wire along with the pipes routed with UG cables, termination at all the cable end terminations. Giving connection with the existing earthing loop in control panel including cost of all materials and labour charges etc. complete. |
| 32 | Item No.8 Supplying, fixing, testing and commissioning SS 316/Poly-Carbide material surface mounting Digital Timer of 230 Volt single phase supply with 14 – 20 Amps direct load capacity from NO/NC terminal with IP - 65 enclosure daily programmable with suitable NO + NC auxilary contacts control voltage 230/220V AC of reputed make like L&T, Legrand, Havells etc. including cost of all materials and labour charges etc complete. |
| 33 | Item No.9 Supply of 12 Mtr high mast area lighting system with following accessories at Agatti including all taxes, packing and forwarding charges & cost of transportation charges from mainland to Agatti island. (a) Mast shaft shall be in one/two section hot dip galvanised mast shaft suitable for wind velocity as per IS 875, accessories like head frame, steel wire rope 5mm dia( 7/19 construction), trailing cable, double drum winch, galvanised lantern carriage arrangements suitable for 6 luminaries symmetrically and its control gear boxes and lighting finial. The integral power tool installes inside the base compartment for its operation (b) Foundation bolt manufactured of special steel along with nuts, washers, anchor plates and templates, required for the mast. (c) Supply of 6 nos. 150W LED flood light fitting with all accessories. Luminaries housing components to be extrude aluminum, with high performance heat sinks, luminaries provided with heat resistant toughened glass, extruded aluminum control gear compartment, colour temp – 5700 K +/- 300 K, LEDs are provided with secondary lens optics to get optimum optical performance. Internal protection against lightening, surge voltage, open/short circuit protection. Power factor>95%, System Lumen package shall be as per IESNA LM79-80,IP66 protection, luminaries is provided with with a mounting bracket fixe on die cast aluminum end plates for aiming adjustment. Make: Bajaj/ Crompton/ Havells or Equivalent (d) Supply of LED aviation obstruction light (e) Control panel housing 32 Amp TPN MCB incomer, single dial timer contactor circuit for the automatic control of luminaries outgoing terminals and control circuit for the power tool motor etc., complete including all taxes and packaging and forwarding charges. (f) Providing power supply line to high mast including cost of suitable cable & other materials, all labour charges, etc., complete (g) Providing founadtion structure for installing the high mast lighting system at site as per the standard drawing as directed by the Engineer in Charge etc., including cost of all materials and labour charges etc., complete. (h) Erection of the high mast lighting system with the help of the suitable equipments at the location as directed by the Engineer in Charge, installation of the control panel and wiring the luminaries including cost of all wiring materials and cost of all labour charges etc. complete. |
| 34 | SHEDULE – III Location :- MINICOY Item No.1 Breaking and removing the concrete to form duct of 15cmx10cm for laying power cable/Electrical wire through PVC Pipe, covering the duct after laying the cable with cement mortor and dismantling cement concrete 1:3:6 or 1:2:4 richer mix & disposing the debris etc., and providing R.C.C. 1:1½ :3 (one cement, one and half sand and three granite stone jelly 20mm down size) for column, beam, slab etc., including cost of all labour charge, cost of minor tools & plants, cost of materials etc., complete. |
| 35 | Item No.2 Supply & Laying of 16 sqmm X 4 core of PVC / XLPE insulated PVC inner sheeted unarmoured aluminum power cable of 1.10 KV grade under ground cable of reputed make like : Havells/ Unicab/ Suncab/ Toshicab/ Polycab confirms to IS 1554 / 7098 through DWC pipe of suitable size duct provided as per the instruction of EIC, including cost of all labour charges, cost of minor tools, applicable GST and LWC cost of UG cables, DWC pipes, all materials etc., complete. |
| 36 | Item No.3 Wiring for circuit / sub main wiring along with earthwire with the following size of FR PVC insulated multistrand copper conductor cable in surface / recessed PVC conduit as required. (CPWD - 1.14.4) |
| 37 | 2 x 6 sqmm along with earth wire 1 x 6 sqmm. |
| 38 | Item No.4 Dismantling and removing the R.C.C. Lamp Post of light 5.50 meter from the approach of jetty by providing necessary scaffoldings up to the required hight, transporting the debries with in a lead of 2 Kms, disposing the same without causing hindrance to the crafts and people utilizing the jetty as directed by the EIC, including cost of all labour charges, tools and plants, transportation charges etc; complete. |
| 39 | Item No.5 Supplying, Erection and Commisioning of CNC filament wound Glass Reinforced Polymer (GRP) street lighting poles (Colour: Silver Grey) of anchor type with base plate of 250X250 mm , shaft length 6000 mm, top/bottom OD dia 114/170 ?5mm apprx. average thickness 6 mm with integral/external junction box with 4 terminals of 6 sq. mm & 6 AMP SP MCB (IP65), GRP Single side arm bracket of 1000 mm length with SS JB Clamp-D 1075 including wiring with 3 X 1.5 sqmm PVC insulated multistrad copper wire from junction box to lamp set etc complete of SUMIP/ BAJAJ/SATYAM - Make or Equivalent in other reputed make including GST, Labour cess, cost of all materials of GRP lamp post, single arm, base plate and labour charges etc complete including cost of laying PCC pedastal of 0.40X0.40X0.75 Mtr(WXBXH) |
| 40 | Item No.6 Supply, installation, testing and commissioning of LED street light luminaire / Flood lights as per the following specification on the lamp post / high mast light towers provided, giving connection with 1.5 sqmm PVC insulated copper wire etc as required but including cost of fittings, GST, Labour Cess, cost of all materials, labour charges, scaffolding charges and minor tools etc complete. |
| 41 | 90 watt LED street light luminaire - Make - Bajaj , Model - EDGE, BRTFG 90 W LED 1(or) Equalent in other reputed make like - Havells / Crompton / Philips. LED streetlight shall be made up of pressure die cast housing with toughned glass and individual LEDs with secondary optics and IP66 protection. |
| 42 | 150 watt (85 lumen/watt) rating LED Flood light fitting of reputed make like Crompon / Bajaj / Havells on the top of the light carriage of the highmast lighting tower including cost of all materials and all labour charges etc. complete LED streetlight shall be made up of pressure die cast housing with toughned glass and individual LEDs with secondary optics and IP66 protection. (for existing Highmast) |
| 43 | Item No.7 Supply, installation, testing and commssioning of outdoor type floor mounted power pillar box of 1200 x 900 x 450 mm size distributin pillar box (As per drawing) made of SINTEX foam PVC sheet of 8 mm thick non extenable type with 4 strip Aluminium busbar suitable for LT 3 phase, 415 V, 100Amps capacity with twin door open with locking arrangement in front side and have the facility to accommadate various size of electrical items and out side pasted with standard size of danger plate as required. The rate including cost of all materials and labour charges, minor tools and plants, GST, LWC and providing CC pedestal as per drawing etc. complete. |
| 44 | Item No.8 Supplying and fixing following 6/8 way, single pole and neutral, sheet steel, MCB distribution board, 240/415 volts, 32/40 Amps on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) (2.3.2) including cost of all materials, GST, Labour Cess and minor tools etc complete. |
| 45 | Item No.9 Supplying and fixing 40/63 Amps rating, four pole, (three phase and neutral) MCB 415 volts /residual current circuit breaker (RCCB) having a sensitivity current 30 milli amperes in the existing MCB DB complete with connections, testing and commissioning etc. as required including cost of all materials, GST, Labour Cess and minor tools etc complete. (2.15.3) |
| 46 | Item No.10 Supply & installation of Maintenance Free Earth (MFE) Station in solid earth electrode comprising of 1 nos. of 17.0 mm dia., 3.0 mtr long copper bonded stainless / nickel steel alloy rod, molecularly bonded copper of 99.9% purity with minimum copper coating thickness of 250 microns including supply of copper coated steel rod. Supply of suitable high grade copper alloy Rod to tape Clamp - Type ''A'' with extra grip / U-bolt Rod Clamps - Type 'E' with Double Plate for connecting earthing strip to earth electrode. The rod has been tested for Dimension, Marking, Tensile Strength, Salt mist, coating thickness, Electrical resistivity test before and after corrosion test as per IEC 62561-2 & UL 467 meets the requirements of IS:3043 and IEC 60364-5-54, tested for short circuit current withstanding capacity. The other materials and tools required for excavation of earth hard/ soft soil and driving rod in earth with augured hole dia. of 75-100mm in ground including civil works like excavation & refilling of earth, also including supply and filling conductivity / earth enhancement compound (confirming to IEC:62651-7 with latest amendments) filled around the copper bonded steel rod to a minimum depth of 3.0 Mtrs. from ground level including civil works like excavation & refilling of earth & also providing precast RCC inspection chamber with RCC cover slab for each electrode complete with all interconnections as required & as directed by EIC. |
| 47 | Item No.11 Supplying and laying of 12 SWG bare copper wire along with the pipes routed with UG cables, termination at all the cable end terminations. Giving connection with the existing earthing loop in control panel including cost of all materials and labour charges etc. complete. |
| 48 | Item No.12 Supplying, fixing, testing and commissioning SS 316/Poly-Carbide material surface mounting Digital Timer of 230 Volt single phase supply with 14 – 20 Amps direct load capacity from NO/NC terminal with IP - 65 enclosure daily programmable with suitable NO + NC auxilary contacts control voltage 230/220V AC of reputed make like L&T, Legrand, Havells etc. including cost of all materials and labour charges etc complete. |
| 49 | Item No.13 Supply of 12 Mtr high mast area lighting system with following accessories at Minicoy including all taxes, packing and forwarding charges & cost of transportation charges from mainland to Minicoy island (a) Mast shaft shall be in one/two section hot dip galvanised mast shaft suitable for wind velocity as per IS 875, accessories like head frame, steel wire rope 5mm dia( 7/19 construction), trailing cable, double drum winch, galvanised lantern carriage arrangements suitable for 6 luminaries symmetrically and its control gear boxes and lighting finial. The integral power tool installes inside the base compartment for its operation. (b) Foundation bolt manufactured of special steel along with nuts, washers, anchor plates and templates, required for the mast. (c) Supply of 6 nos 120W LED flood Light fittings with all accossories liminaries housing components to be extrude aluminium with high. (d) Supply of LED aviation obstruction light (e) Control panel housing 32 Amp TPN MCB incomer, single dial timer contactor circuit for the automatic control of luminaries outgoing terminals and control circuit for the power tool motor etc., complete including all taxes and packaging and forwarding charges. (f) Providing power supply line to high mast including cost of suitable cable & other materials, all labour charges, etc., complete (g) Providing founadtion structure for installing the high mast lighting system at site as per the standard drawing as directed by the Engineer in Charge etc., including cost of all materials and labour charges etc., complete. (h) Erection of the high mast lighting system with the help of the suitable equipments at the location as directed by the Engineer in Charge, installation of the control panel and wiring the luminaries including cost of all wiring materials and cost of all labour charges etc. complete. |
| 50 | SHEDULE – IV Location :- AMINI Item No.1 Breaking and removing the concrete to form duct of 15cmx10cm for laying power cable/Electrical wire through PVC Pipe, covering the duct after laying the cable with cement mortor and dismantling cement concrete 1:3:6 or 1:2:4 richer mix & disposing the debris etc., and providing R.C.C. 1:1½ :3 (one cement, one and half sand and three granite stone jelly 20mm down size) for column, beam, slab etc., including cost of all labour charge, cost of minor tools & plants, cost of materials etc., complete. |
| 51 | Item No.2 Supply & Laying of following sizes of PVC / XLPE insulated PVC inner sheeted unarmoured aluminum power cable of 1.10 KV grade under ground cable of reputed make like : Havells/ Unicab/ Suncab/ Toshicab/ Polycab confirms to IS 1554 / 7098 through DWC pipe of suitable size duct provided as per the instruction of EIC, including cost of all labour charges, cost of minor tools, applicable GST and LWC but including cost of UG cables, DWC pipes, all materials etc., complete |
| 52 | 70 sqmm x 3½ core |
| 53 | 16 sqmm x 4 core |
| 54 | Item No.3 Wiring for circuit / sub main wiring along with earthwire with the following size of FR PVC insulated multistrand copper conductor cable in surface / recessed PVC conduit as required. (CPWD - 1.14.4) |
| 55 | 2 x 6 sqmm along with earth wire 1 x 6 sqmm. |
| 56 | Item No.4 Dismantling and removing the R.C.C. Lamp Post of light 5.50 meter from the approach of jetty by providing necessary scaffoldings up to the required hight, transporting the debries with in a lead of 2 Kms, disposing the same without causing hindrance to the crafts and people utilizing the jetty as directed by the EIC, including cost of all labour charges, tools and plants, transportation charges etc; complete. |
| 57 | Item No.5 Supplying, Erection and Commissioning of CNC filament wound Glass Reinforced Polymer (GRP) street lighting poles (Colour: Silver Grey) of anchor type with base plate of 250X250 mm , shaft length 6000 mm, top/bottom OD dia 114/170 ?5mm apprx. average thickness 6 mm with integral/external junction box with 4 terminals of 6 sq. mm & 6 AMP SP MCB (IP65), GRP Single side arm bracket of 1000 mm length with SS JB Clamp-D 1075 including wiring with 3 X 1.5 sqmm PVC insulated multistrad copper wire from junction box to lamp set etc complete of SUMIP/ BAJAJ/SATYAM - Make or Equivalent in other reputed make including GST, Labour cess, cost of all materials of GRP lamp post, single arm, base plate and labour charges etc complete including cost of laying PCC pedastal of 0.40X0.40X0.75 Mtr(WXBXH) |
| 58 | Item No.6 Supply, installation, testing and commissioning of LED street light luminaire / Flood lights as per the following specification on the lamp post / high mast light towers provided, giving connection with 1.5 sqmm PVC insulated copper wire etc as required but including cost of fittings, GST, Labour Cess, cost of all materials, labour charges, scaffolding charges and minor tools etc complete. |
| 59 | 90 watt LED street light luminaire - Make - Bajaj , Model - EDGE, BRTFG 90 W LED 1(or) Equalent in other reputed make like - Havells / Crompton / Philips. LED streetlight shall be made up of pressure die cast housing with toughned glass and individual LEDs with secondary optics and IP66 protection. |
| 60 | 150 watt (85 lumen/watt) rating LED Flood light fitting of reputed make like Crompon / Bajaj / Havells on the top of the light carriage of the highmast lighting tower including cost of all materials and all labour charges etc. complete LED streetlight shall be made up of pressure die cast housing with toughned glass and individual LEDs with secondary optics and IP66 protection. (for existing Highmast) |
| 61 | Item No.7 Supplying and laying of 12 SWG bare copper wire along with the pipes routed with UG cables, termination at all the cable end terminations. Giving connection with the existing earthing loop in control panel including cost of all materials and labour charges etc. complete. |
| 62 | Item No.8 Supplying, fixing, testing and commissioning SS 316/Poly-Carbide material surface mounting Digital Timer of 230 Volt single phase supply with 14 – 20 Amps direct load capacity from NO/NC terminal with IP - 65 enclosure daily programmable with suitable NO + NC auxilary contacts control voltage 230/220V AC of reputed make like L&T, Legrand, Havells etc. including cost of all materials and labour charges etc complete. |
| 63 | Item No.9 Supply of 12 Mtr high mast area lighting system with following accessories at Amini including all taxes, packing and forwarding charges & cost of transportation charges from mainland to Amini island. (a) Mast shaft shall be in one/two section hot dip galvanised mast shaft suitable for wind velocity as per IS 875, accessories like head frame, steel wire rope 5mm dia( 7/19 construction), trailing cable, double drum winch, galvanised lantern carriage arrangements suitable for 6 luminaries symmetrically and its control gear boxes and lighting finial. The integral power tool installes inside the base compartment for its operation.(b) Foundation bolt manufactured of special steel along with nuts, washers, anchor plates and templates, required for the mast.(c) Supply of 6 nos. 150W LED flood light fitting with all accessories. Luminaries housing components to be extrude aluminum, with high performance heat sinks, luminaries provided with heat resistant toughened glass, extruded aluminum control gear compartment, colour temp – 5700 K +/- 300 K, LEDs are provided with secondary lens optics to get optimum optical performance. Internal protection against lightening, surge voltage, open/short circuit protection. Power factor>95%, System Lumen package shall be as per IESNA LM79-80,IP66 protection, luminaries is provided with with a mounting bracket fixe on die cast aluminum end plates for aiming adjustment. Make: Bajaj/ Crompton/ Havells or Equivalent(d) Supply of LED aviation obstruction light(e) Control panel housing 32 Amp TPN MCB incomer, single dial timer contactor circuit for the automatic control of luminaries outgoing terminals and control circuit for the power tool motor etc., complete including all taxes and packaging and forwarding charges.(f) Providing power supply line to high mast including cost of suitable cable & other materials, all labour charges, etc., complete (g) Providing founadtion structure for installing the high mast lighting system at site as per the standard drawing as directed by the Engineer in Charge etc., including cost of all materials and labour charges etc., complete.(h) Erection of the high mast lighting system with the help of the suitable equipments at the location as directed by the Engineer in Charge, installation of the control panel and wiring the luminaries including cost of all wiring materials and cost of all labour charges etc. complete. |
| 64 | SHEDULE – V Location :- ANDROTH Item No.1 Supply & Laying of following sizes of PVC / XLPE insulated PVC inner sheeted unarmoured aluminum power cable of 1.10 KV grade under ground cable of reputed make like : Havells/ Unicab/ Suncab/ Toshicab/ Polycab confirms to IS 1554 / 7098 through DWC pipe of suitable size duct provided as per the instruction of EIC,including cost of all labour charges, cost of minor tools, applicable GST and LWC cost of UG cables, DWC pipes, all materials etc., complete. |
| 65 | 120 sqmm x 3½ core |
| 66 | 16 sqmm x 4 core |
| 67 | Item No.2 Dismantling and removing the R.C.C. Lamp Post of light 5.50 meter from the approach of jetty by providing necessary scaffoldings up to the required hight, transporting the debries with in a lead of 2 Kms, disposing the same without causing hindrance to the crafts and people utilizing the jetty as directed by the EIC, including cost of all labour charges, tools and plants, transportation charges etc; complete. |
| 68 | Item No.3 Supplying, Erection and Commissioning of CNC filament wound Glass Reinforced Polymer (GRP) street lighting poles (Colour: Silver Grey) of anchor type with base plate of 250X250 mm , shaft length 6000 mm, top/bottom OD dia 114/170 ?5mm apprx. average thickness 6 mm with integral/external junction box with 4 terminals of 6 sq. mm & 6 AMP SP MCB (IP65), GRP Single side arm bracket of 1000 mm length with SS JB Clamp-D 1075 including wiring with 3 X 1.5 sqmm PVC insulated multistrad copper wire from junction box to lamp set etc complete of SUMIP/ BAJAJ/SATYAM - Make or Equivalent in other reputed make including GST, Labour cess, cost of all materials of GRP lamp post, single arm, base plate and labour charges etc complete including cost of laying PCC pedastal of 0.40X0.40X0.75 Mtr(WXBXH) |
| 69 | Item No.4 Supply, installation, testing and commissioning of LED street light luminaire / Flood lights as per the following specification on the lamp post / high mast light towers provided, giving connection with 1.5 sqmm PVC insulated copper wire etc as required but including cost of fittings, GST, Labour Cess, cost of all materials, labour charges, scaffolding charges and minor tools etc complete. |
| 70 | 90 watt LED street light luminaire - Make - Bajaj , Model - EDGE, BRTFG 90 W LED 1(or) Equalent in other reputed make like - Havells / Crompton / Philips. LED streetlight shall be made up of pressure die cast housing with toughned glass and individual LEDs with secondary optics and IP66 protection. |
| 71 | 150 watt (85 lumen/watt) rating LED Flood light fitting of reputed make like Crompon / Bajaj / Havells on the top of the light carriage of the highmast lighting tower including cost of all materials and all labour charges etc. complete LED streetlight shall be made up of pressure die cast housing with toughned glass and individual LEDs with secondary optics and IP66 protection. (for existing Highmast) |
| 72 | Item No.5 Supply, installation, testing and commssioning of outdoor type floor mounted power pillar box of 1200 x 900 x 450 mm size distributin pillar box (As per drawing) made of SINTEX foam PVC sheet of 8 mm thick non extenable type with 4 strip Aluminium busbar suitable for LT 3 phase, 415 V, 100Amps capacity with twin door open with locking arrangement in front side and have the facility to accommadate various size of electrical items and out side pasted with standard size of danger plate as required. The rate including cost of all materials and labour charges, minor tools and plants, GST, LWC and providing CC pedestal as per drawing etc. complete. |
| 73 | Item No.6 Supplying and fixing following 6/8 way, single pole and neutral, sheet steel, MCB distribution board, 240/415 volts, 32/40 Amps on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) (2.3.2) including cost of all materials, GST, Labour Cess and minor tools etc complete. |
| 74 | Item No.7 Supplying and fixing 40/63 Amps rating, four pole, (three phase and neutral) MCB 415 volts /residual current circuit breaker (RCCB) having a sensitivity current 30 milli amperes in the existing MCB DB complete with connections, testing and commissioning etc. as required including cost of all materials, GST, Labour Cess and minor tools etc complete. (2.15.3) |
| 75 | Item No.8 Supplying and laying of 12 SWG bare copper wire along with the pipes routed with UG cables, termination at all the cable end terminations. Giving connection with the existing earthing loop in control panel including cost of all materials and labour charges etc. complete. |
| 76 | Item No.9 Supplying, fixing, testing and commissioning SS 316/Poly-Carbide material surface mounting Digital Timer of 230 Volt single phase supply with 14 – 20 Amps direct load capacity from NO/NC terminal with IP - 65 enclosure daily programmable with suitable NO + NC auxilary contacts control voltage 230/220V AC of reputed make like L&T, Legrand, Havells etc. including cost of all materials and labour charges etc complete. |
| 77 | Item No.10 Supply of 12 Mtr high mast area lighting system with following accessories at ANDROTH including all taxes, packing and forwarding charges & cost of transportation charges from mainland to Androth island.(a) Mast shaft shall be in one/two section hot dip galvanised mast shaft suitable for wind velocity as per IS 875, accessories like head frame, steel wire rope 5mm dia( 7/19 construction), trailing cable, double drum winch, galvanised lantern carriage arrangements suitable for 6 luminaries symmetrically and its control gear boxes and lighting finial. The integral power tool installes inside the base compartment for its operation.(b) Foundation bolt manufactured of special steel along with nuts, washers, anchor plates and templates, required for the mast.(c) Supply of 6 nos. 150W LED flood light fitting with all accessories. Luminaries housing components to be extrude aluminum, with high performance heat sinks, luminaries provided with heat resistant toughened glass, extruded aluminum control gear compartment, colour temp – 5700 K +/- 300 K, LEDs are provided with secondary lens optics to get optimum optical performance. Internal protection against lightening, surge voltage, open/short circuit protection. Power factor>95%, System Lumen package shall be as per IESNA LM79-80,IP66 protection, luminaries is provided with with a mounting bracket fixe on die cast aluminum end plates for aiming adjustment. Make: Bajaj/ Crompton/ Havells or Equivalent(d) Supply of LED aviation obstruction light(e) Control panel housing 32 Amp TPN MCB incomer, single dial timer contactor circuit for the automatic control of luminaries outgoing terminals and control circuit for the power tool motor etc., complete including all taxes and packaging and forwarding charges.(f) Providing power supply line to high mast including cost of suitable cable & other materials, all labour charges, etc., complete (g) Providing founadtion structure for installing the high mast lighting system at site as per the standard drawing as directed by the Engineer in Charge etc., including cost of all materials and labour charges etc., complete.(h) Erection of the high mast lighting system with the help of the suitable equipments at the location as directed by the Engineer in Charge, installation of the control panel and wiring the luminaries including cost of all wiring materials and cost of all labour charges etc. complete. |
| 78 | SHEDULE – VI Location :- KALPENI Item No.1 Breaking and removing the concrete to form duct of 15cmx10cm for laying power cable/Electrical wire through PVC Pipe, covering the duct after laying the cable with cement mortor and dismantling cement concrete 1:3:6 or 1:2:4 richer mix & disposing the debris etc., and providing R.C.C. 1:1½ :3 (one cement, one and half sand and three granite stone jelly 20mm down size) for column, beam, slab etc., including cost of all labour charge, cost of minor tools & plants, cost of materials etc., complete. |
| 79 | Item No.2 Suppluy & Laying of 16 sqmm X 4 core of PVC / XLPE insulated PVC inner sheeted unarmoured aluminum power cable of 1.10 KV grade under ground cable of reputed make like : Havells/ Unicab/ Suncab/ Toshicab/ Polycab confirms to IS 1554 / 7098 through DWC pipe of suitable size duct provided as per the instruction of EIC,including cost of all labour charges, cost of minor tools, applicable GST and LWC cost of UG cables, DWC pipes, all materials etc., complete. |
| 80 | Item No.3 Dismantling and removing the R.C.C. Lamp Post of light 5.50 meter from the approach of jetty by providing necessary scaffoldings up to the required hight, transporting the debries with in a lead of 2 Kms, disposing the same without causing hindrance to the crafts and people utilizing the jetty as directed by the EIC, including cost of all labour charges, tools and plants, transportation charges etc; complete. |
| 81 | Item No.4 Supplying, Erection and Commissioning of CNC filament wound Glass Reinforced Polymer (GRP) street lighting poles (Colour: Silver Grey) of anchor type with base plate of 250X250 mm , shaft length 6000 mm, top/bottom OD dia 114/170 ?5mm apprx. average thickness 6 mm with integral/external junction box with 4 terminals of 6 sq. mm & 6 AMP SP MCB (IP65), GRP Single side arm bracket of 1000 mm length with SS JB Clamp-D 1075 including wiring with 3 X 1.5 sqmm PVC insulated multistrad copper wire from junction box to lamp set etc complete of SUMIP/ BAJAJ/SATYAM - Make or Equivalent in other reputed make including GST, Labour cess, cost of all materials of GRP lamp post, single arm, base plate and labour charges etc complete including cost of laying PCC pedastal of 0.40X0.40X0.75 Mtr(WXBXH) |
| 82 | Item No.5 Supply, installation, testing and commissioning of LED street light luminaire / Flood lights as per the following specification on the lamp post / high mast light towers provided, giving connection with 1.5 sqmm PVC insulated copper wire etc as required but including cost of fittings, GST, Labour Cess, cost of all materials, labour charges, scaffolding charges and minor tools etc complete. |
| 83 | 90 watt LED street light luminaire - Make - Bajaj , Model - EDGE, BRTFG 90 W LED 1(or) Equalent in other reputed make like - Havells / Crompton / Philips. LED streetlight shall be made up of pressure die cast housing with toughned glass and individual LEDs with secondary optics and IP66 protection. |
| 84 | Item No.6 Supplying and laying of 12 SWG bare copper wire along with the pipes routed with UG cables, termination at all the cable end terminations. Giving connection with the existing earthing loop in control panel including cost of all materials and labour charges etc. complete. |
| 85 | Item No.7 Supplying, fixing, testing and commissioning SS 316/Poly-Carbide material surface mounting Digital Timer of 230 Volt single phase supply with 14 – 20 Amps direct load capacity from NO/NC terminal with IP - 65 enclosure daily programmable with suitable NO + NC auxilary contacts control voltage 230/220V AC of reputed make like L&T, Legrand, Havells etc. including cost of all materials and labour charges etc complete. |
| 86 | Item No.8 Supply of 12 Mtr high mast area lighting system with following accessories at Kalpeni including all taxes, packing and forwarding charges & cost of transportation charges from mainland to Kalpeni island.(a) Mast shaft shall be in one/two section hot dip galvanised mast shaft suitable for wind velocity as per IS 875, accessories like head frame, steel wire rope 5mm dia( 7/19 construction), trailing cable, double drum winch, galvanised lantern carriage arrangements suitable for 6 luminaries symmetrically and its control gear boxes and lighting finial. The integral power tool installes inside the base compartment for its operation.(b) Foundation bolt manufactured of special steel along with nuts, washers, anchor plates and templates, required for the mast.(c) Supply of 6 nos. 150W LED flood light fitting with all accessories. Luminaries housing components to be extrude aluminum, with high performance heat sinks, luminaries provided with heat resistant toughened glass, extruded aluminum control gear compartment, colour temp – 5700 K +/- 300 K, LEDs are provided with secondary lens optics to get optimum optical performance. Internal protection against lightening, surge voltage, open/short circuit protection. Power factor>95%, System Lumen package shall be as per IESNA LM79-80,IP66 protection, luminaries is provided with with a mounting bracket fixe on die cast aluminum end plates for aiming adjustment. Make: Bajaj/ Crompton/ Havells or Equivalent(d) Supply of LED aviation obstruction light(e) Control panel housing 32 Amp TPN MCB incomer, single dial timer contactor circuit for the automatic control of luminaries outgoing terminals and control circuit for the power tool motor etc., complete including all taxes and packaging and forwarding charges.(f) Providing power supply line to high mast including cost of suitable cable & other materials, all labour charges, etc., complete (g) Providing founadtion structure for installing the high mast lighting system at site as per the standard drawing as directed by the Engineer in Charge etc., including cost of all materials and labour charges etc., complete.(h) Erection of the high mast lighting system with the help of the suitable equipments at the location as directed by the Engineer in Charge, installation of the control panel and wiring the luminaries including cost of all wiring materials and cost of all labour charges etc. complete. Please Enable Macros to View BoQ information |
