|
| 1 | Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50 m.Ordinary rock |
| 2 | Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m :All kinds of soil : Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia |
| 3 | Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth,sides of foundation etc. complete. |
| 4 | Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. |
| 5 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 cement : 4 coarse sand (zone-III): 8 graded stone aggregate 40 mm nominal size) |
| 6 | Centering and shuttering including strutting, propping etc. and removal of form work for :Columns, piers, abutments, pillars, posts and struts. |
| 7 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All M-20work up to plinth level :1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size) |
| 8 | Centering and shuttering including strutting, propping etc. and removal of form for : Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 9 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Cold twisted bars. |
| 10 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approvedmake, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 11 | Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete. 40mm |
| 12 | Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessaryaccessories and screws etc. complete. |
| 13 | Steel work in built up(round, square or rectangular hollow tubes,structural steel, nut bolts etc.)trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes. |
| 14 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. |
| 15 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08%and conforming to IS : 15622 , of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm(Make Kajaria, Nitco,RAK, Somany) |
| 16 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion,(i) Single socketed pipes.110 mm diameter |
| 17 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. |
| 18 | Coupler 110 |
| 19 | Tee without door 75X75X75 |
| 20 | Tee without door110x110x110 mm |
| 21 | Tee with door110x110x110 mm |
| 22 | Bend 87.5° 75 mm bend |
| 23 | Bend 87.5°110 mm bend |
| 24 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 75 mm |
| 25 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.clamp 110 |
| 26 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-Charge) of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /seIf tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. (National,Tata, Jindal make) |
| 27 | 12 mm cement plaster of mix :1:4 (1 cement: 4 sand) |
| 28 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new work- on steel works |
| 29 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.32 mm dia Flexible pipe |
| 30 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 5 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete |
| 31 | Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour.Waste coupling 31 mm dia of 79 mm length and 62mm breadth weighing not less than 45 gms |
| 32 | Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. |
| 33 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms |
| 34 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings,including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittingswith one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Internal work - Exposed on wall 15 mm nominal outer dia Pipes |
| 35 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings,including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittingswith one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge Internal work - Exposed on wall 20 mm dia nominal bore |
| 36 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including all PVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittingswith one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge Internal work - Exposed on wall 25 mm dia nominal bore |
| 37 | Providing and fixing brass bib cock of approved quality :15 mm nominal bore |
| 38 | Providing and fixing brass stop cock of approved quality :15 mm nominal bore |
| 39 | Providing and fixing brass stop cock of approved quality :20 mm nominal bore |
| 40 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screed end) :25 mm nominal bore |
| 41 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 42 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore |
| 43 | Providing and fixing PTMT grating of approved quality and colour. |
| 44 | 100 mm nominal dia Circular type |
| 45 | 125 mm nominal dia with 25 mm waste hole |
| 46 | Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge |
| 47 | Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour.15 mm nominal bore with 30cm length |
| 48 | Providing and fixing PTMT extension nipple for water tank pipe, fittingsof approved quality and colour.25mm nominal bore, weighing not less than 62 gms |
| 49 | Constructing brick masonry road gully chamber 45x45x77.5 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand ) with precast R.C.C. vertical grating complete as per standard design :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 50 | Labour for shifting etc. unforseen work |
| 51 | Brick work 100mm in superstructure in Cement mortar 1:4 (1cement :4 coarse sand) |
| 52 | Providing & Fixing cement concrete coloured garden benches |
| 53 | Providing and fixing air bubble sheet standard make under roof truss with all fixture and fittings etc. complete |
| 54 | Providing & fixing CP fosset jet for European type WC seat including CP lead, push button etc, complete as per direction of Engineer-in-charge |
| 55 | Providing and fixing door in aluminium frame(5 micron powder coated) partially glazed and partially 12 mm ISI board with rubber gasket, beading, handle,hinges,tower bolts, stopper etc complete with fittings and accessories as per direction of E-in-C |
| 56 | Providing and fixing glazed windows/ventilators in aluminium frame(5 micron powder coated) with fixing of hinges,tower bolts, beading, gasket etc complete with fittings and accessories as per direction of E-in-C |
| 57 | Providing and fixing partition(fixed)in aluminium frame(5 micron powder coated-18 gauge) partially glazed and partially 11 mm ISI board with rubber gasket, beading, handle,hinges,tower bolts, stopper etc complete with fittings and accessories as per direction of E-in-C |
| 58 | Providing and fixing in position composite wall panels consisting of 45-50 mm thick Rock wool/Air Bubble sandwiched between profile Sheet outer and internal Gypsum/cement fibre sheet 6 mm thickness complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses, profile sheet and including cutting to size and shape wherever required. all complete as per drawings, specification and direction of the Engineer in Charge including the cost of putty & internal paint, Self driven screws, nuts, Bolts, washers, accessories, labour etc. |
| 59 | Providing and fixing white vitreous china indian water closet (European/orissa type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required |
| 60 | Providing and fixing vitreous china European type water closet with seat & lid fixed with hinges and rubber buffers, 10 litre low level flushing cistern with fitting and brackets, 40 mm flush bend, 20 mm over flow pipe, complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required: White vitreous china WC pan with white solid plastic seat and lid with white vitreous china flushing cistern and flush bend. |
| 61 | Providing and fixing wash basin with C.I. brackets, 15 mm pillar taps, 32 mm waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Wash basin with a pair of 15 mm pillar taps |
| 62 | Providing and fixing mirror of superior glass (of approved quality) complete screws and washers complete. |
| 63 | Providing and fixing under ground PVC septik tank with all fittings and fixtures etc complete-1000 litre |
| 64 | P/f false ceiling 600X600 mm Size (Select section) by fixing aluminium section including T-section and fixing Aluminium section powder coated medium gauge by suspending roof by suitable means, clips etc. Including supporting aluminium section as per site requirement as required and desired by E-in-C |
| 65 | P/F Acrylic 2mm thick Sign board |
| 66 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box/celling rose and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group 'C'. |
| 67 | Wiring for circuit / submain wiring alongwith earth wire with the following size of FRLS PVC insulated copper conductor, single core cable in surface / recessed PVC conduit as required |
| 68 | 2 X 1.5 Sq.mm + 1 X 1.5 Sq.mm earth wire. |
| 69 | 2 X 2.5 Sq.mm + 1 X 2.5 Sq.mm earth wire. |
| 70 | 2 X 4 Sq.mm + 1 X 4 Sq.mm earth wire. |
| 71 | 2 X 6 Sq.mm + 1 X 6 Sq.mm earth wire.. |
| 72 | Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. |
| 73 | Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required |
| 74 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. (Make - BEC/Kissan/Kasta/ Supreme/ Sudhakar/ Reliance) |
| 75 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6pin 15 / 16 & 5 / 6 amps modular socket outlet and 15 / 16 amps modular switch, connection, painting etc. as required. |
| 76 | Supplying and fixing follwing modular Switch/Socket on the existing modular plate & switch box including connections excluding modular plate etc as required. |
| 77 | 5/6amps switch |
| 78 | 3 pin 5/6 Amps Socket outlet |
| 79 | 15/16 A switch |
| 80 | 6 pin 15/16 A socket outlet |
| 81 | Bell push |
| 82 | Supplyiong and Fixing following size/ Modular plate, GI box alongwith modular base & cover plate for modular switchesin recess ets as required |
| 83 | 1/2 module |
| 84 | 6 module |
| 85 | Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) |
| 86 | 12 way Double Door |
| 87 | Supplying and fixing 5 amps to 32 amps rating, 240 volts 'C' series, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 88 | Single Pole |
| 89 | Single Pole and Neutral |
| 90 | Supplying and fixing of following ways horizantal type , three pole and neutral , Sheet Steel MCB distribution board 415 V surface/recess completed with tinned copper bus bar, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, common neutral link, earth bar, power coated din bar for mounting MCBs (but without MCBs/RCCB's/isolator) as required . |
| 91 | 4 Way(4+12) Double Door |
| 92 | Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required |
| 93 | Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm) |
| 94 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. |
| 95 | 3.5 X 35 sq.mm ( 32 mm) |
| 96 | Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc..direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. |
| 97 | a) 63 mm dia (OD-63 mm & ID-51 mm nominal) |
| 98 | Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 99 | 63 Amp |
| 100 | Supplying, installation, Testing & Commissioning ofPanel light 2x2 ft., of following body material andconstruction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -5 0C to 40 0C, internalsurge protection of 2.5 KV with Short & Open circuit protection, THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR (Unified Glare Rating) < 19, Flicker free, (flicker should be below 5 %), life time (LED, Driver & electrical circuitry), of minimum 50000 Burning Hours with, 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Colour Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard. Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥105 <120 lm/Watt output . LM79 & LM80 Test report and all testing requiredfor LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not riseabove 90°C). Powder coated die cast /Extruded aluminiumBody (Thickness > 1.20 mm) |
| 101 | 36 watt |
| 102 | LED Down lighter (SMD Type) (System lumen efficacy ≥ 105 < 120 lm/Watt ) Supplying, installation, Testing & Commissioning of LED Recessed/ surface Down lighter (Round/ square/ Rectangular) SMD type of following body material with PMMA and prismatic diffuser and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80 , UGR (Unified Glare Rating) < 19, Flicker free (flicker should be below 5%), life time (LED,Driver & electrical circuitary), of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends , CCT 3000°K / 4000°K / 5700°K / 6000°K / 6500°K (As per ANSI Bin), SDCM (Standard Deviation Color Matching) |
| 103 | 8 - 10 watt |
| 104 | Supplying, installation, Testing & Commissioning of Flood Light, powder coated pressure die cast aluminum body with built in or separate driver as per the requirement with Driver efficiency >85%, Input voltage: Input voltage: 140-270 Volt AC, freq 50/60 hz, Operating temp range -15 deg 1.16 DELHI SCHEDULE OF RATES (E&M) Volume-II 2025 14 to 50 deg centigrade, internal surge protection of 5 KV L,N,E as per IEC 61000-4-5, Driver efficiency >85%,THD < 10% as per IEC 61000-3-2 , P. F.≥0.95, IP-66,IK-10, CRI >80 , under voltage and over voltage protection, EMI-EMC as per CISPR-15, lenses for beam angle 30 deg120deg as per the application and the project requirement deg, suitable tilt able fitting, life time (LED,Driver & electrical circuitry) of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , SDCM(Standard Deviation Color Matching) |
| 105 | 70 watt |
| 106 | Supplying, Installation, testing & commissioning of size 200 mm sweep fresh air fan (Ventillation fan) in PVC body inbuilt louvers / shutter in the existing opening i/c making the hole to suit the size of the above fan with making good the damages i/c connection as reqd at site. (Make:Crompton/Orient/Bajaj/Havells/Usha/RR ) |
| 107 | Supplying, Installation, testing and commissioning of wall mounted 400 mm sweep, oscillating type for wall mounted fans suitable for operation 230 V AC supply complete with regulator along with taken by double string etc as required. (Make:(Make:Crompton/Orient/Bajaj/Havells/Usha/RR ) |
| 108 | Supplying and laying of following size of XLPE insulated and PVC sheathed aluminum conductor armoured power cable of 1.1 KV grade (ISI Mark ) confirming to IS: 7098 (Part-I) 1988 in the existing RCC / Hume / Metal / PVC pipe/ loose loop connection as reqd. |
| 109 | 3.5 x 35 Sq mm |
| 110 | Supplying and installation of CSIR Develop & Patended Nano Technology based water purifier with capacity of 10-15 liter/hours with min 10 liter storage, maximum 80-100 liter per day duty cycle with filtration of min 1 sediment,2 activated carban and 1 post carbon, min 4 \\" Nano membrane ter etc as required. |
| 111 | Providing and fixing 6 kg capacity ISI marked ABC stored pressure powder (mono ammonium phosphate) Fire Extinguisher IS : 15683 latest revision manufacturer and of CRCA sheet in welded construction, finish with epoxy polyester powder coated complete with brass forged ball valve, gun metal cap and nozzle, including initial filled and wall suspension bracket (suitable for fighting in class 'A', B & 'C' that is wood, textile, flammable liquid, electric and gases. Please Enable Macros to View BoQ information |
