|
| 1 | Desilting the Supply Well, Intake Well / Head Works, Sump of water supply /sewerage works etc. in wet or dry condition including lifts upto 9 M and lead upto 150 M as required beyond the work site, stacking, spreading, including necessaryguarding, etc. complete, as directed by Engineer-in-charge. |
| 2 | Dewatering the excavated trenches and pools of water in the building trenches / pipeline trenches, well works by using pumps and other devices including disposing off water to safe distance as directed by Engineer-in-charge (including cost of |
| 3 | Providing, erecting and giving test of submersible pump set conforming to IS 8034 and motor conforming to IS 9283, with water proof winding. Pump shall be suitable for various delivery head and discharge with stainless steel shaft. Motor suitable for working on 415 V ± 10%, 3 Ph, 50 Hz A.C. Supply, with cable guard, thrust carbon / fiber bearing to withstand entire hydraulic thrust. The pump set shall be suitable for direct coupling, with suitable suction strainer. Pump should have suitable discharge out let as per manufacturer's design. Antithrust stream lined non return valve shall be provided with the pump. 3 m submersible copper conductor cable in single / double run and 2 pairs of suitable size erection clamp 10 mm thick shall be provided with each pump. 7.5BHP 150mm |
| 4 | Supplying and erecting, Flat flexible submersible cable with, Copper Conductor, PVC insulated, and PVC sheathed. 3 core 10SM |
| 5 | Supplying and erecting assembled DOL starter inprovided cubical panel, with ONOFFpush buttons, no volt coil, over load element and required up to 7.5 hp |
| 6 | Supplying & erecting automatic control panel for 3 Ph, 415 volt, A.C.Submersible/centrifugal pump set up to 7.5 HP - 10 H.P. consisting of DOLstarter having relay range 13-21 AMP,S.P.P., Combined ammeter/voltmeter,phase indicating lamp enclosed in CRCA powder coated Vibration proofenclosure with IP 54 protection. Control Panel should offer single phasing, phasereversal, phase imbalance etc. |
| 7 | Providing, erecting Pressure gauge of required range complete with syphon tube, isolating cock suitable for 12 mm dia G.I. Pipe. Pressure gauge shall be installed as directed, with tapping on rising main. 100mm |
| 8 | Providing tools for pumping. |
| 9 | Supplying and erecting, XLPE / PVC insulated, armoured cable 1100 V grade with ISI mark Four core, solid / stranded aluminium conductor with 6 mm thick 25 mm width M.S. spacer with G.I. Earth wire 6 sq mm, complete erected on wall / on pole with 25 X 3 mm M.S. clamps or in provided trench in an approved manner. |
| 10 | Providing earthing with copper earth plate size 30 x 30 x 0.315 cm complete withall materials, testing & recording the results as per specification no. EA-EP |
| 11 | Providing and fabricating structural steel work in rolled sections like joists, channels, angles, tees etc. as per detailed design and drawings or as directed including cutting, fabricating, hoisting, erecting, fixing in position making riveted / bolted /welded connections without connecting plates, braces etc. and including one coat of anticorrosive paint and over it two coats of oil painting of approved quality and shade etc. complete. |
| 12 | Nut Bolts washers 12mm dia. 75mm long |
| 13 | Providing and supplying in standard lengths polyethylene pipes , confirming to IS 4984/14151/12786/13488 with necessary jointing material like mechanical connector i.e. thread / insert joint / quick relase coupler joint / compression fitting joint or flanged joint including all local and cenral taxes, transportation and freight charges inspection charges, loading / unloading charges, conveyance to the departmental stores / site and stacking the same in closed shade duly protecting from sunrays and rains etc complete. |
| 14 | Lowering laying and jointing H.D.P.E. pipes by heating to the ends of pipes with the help of teflon coated electric mirror / heater to the required temperature and then pressing the ends together against each other , to form a monolithic and leakproof joint by thermosetting process. The pressing may be required to be done with Jacks/ Hydraulic Jacks? Butt fusion machine etc complete with all materials labours as directed by Engineer- In-Charge , including given satisfactory hydraulic test. |
| 15 | Providing Specials for all type of pipes, 10 % of pipe cost |
| 16 | Providing & supplying ISI mark CIDF Reflux Valve including ,railway fright ,inspection charges ,unloading from railway wagon .Loading in to truck , , transport to the departmental store / site of work , Unloading, stacking etc. complete . |
| 17 | Providing, ISI mark CI double flanged short body pattern type manually sluice valve of following dia including all taxes, all transportation charges, inspection charges, loading unloading stacking …etc complete. |
| 18 | Lowering, laying & jointing in position following CI D/F Sluice values incuding cost of all labour jointing material, including nut bolts & giving satisfactory hydraulic testing etc complete. |
| 19 | 12 mm size 2 NT capacity wire rope 3 m long with dog bolt 2 Nos. |
| 20 | Providing and supplying in standard lengths Polyethelene Pipes, confirming to IS 4984 / 14151 / 12786 / 13488 with nesessary jointing material like mechanical connector i.e. thread / insert joint / quick release coupler joint / compression fitting joint or flanged joint excluding coupler/specials, including transportation and freight charges, inspection charges, loading / unloading charges, conveyance to the departmental stores & stacking the same in closed shade duly protecting from sunrays & rains, excluding GST levied by GI & GOM in all respect etc. complete. 90mm HDPE pipe PN 8 pipes |
| 21 | Specials for HDPE pipes.5% cost of the item No 1 |
| 22 | Providing double flange sluice valve confirming for IS- 14846 including worn gear arrangements as per test pressure, stainless steel spindle, caps, including inspection charges, transportation upto departmental store, unloading, stacking excluding GST levied by GOI & GOM in all respect etc. complete Sluice valves - PN -1.0 (With by passarrangement) sluice valve 100mm dia |
| 23 | Providing and supplying ISI mark CI D/F reflux valves (non-return valves ) of following dia including railway freight, inspection charges, unloading from railway wagon, loading into truck, transportation upto departmental stores, unloading, stacking excluding GST levied by GOI & GOM in all respect etc. complete. Reflux valves as per I.S.5312 Part I (1984 Reflux valve 100mm dia |
| 24 | Providing and supplying Air Valves as per IS- 14845-2000 and MJP’s standard specifications of approved make and quality of following diameters including railway freight, inspection charges, unloading from railway wagons, loading into truck, transportation upto departmental stores, unloding and stacking excluding GST levied by GOI & GOM in all respect etc. complete. Air valve 25mm Dia |
| 25 | Excavation for foundation / pipe trenches in earth, soils of all types, sand, gravel and soft murum, including removing the excavated material upto a distance of 50 metres and lifts as below, stacking and spreading as directed, normal dewatering, preparing the bed for foundation and excluding backfilling, etc. complete. (Bd-A- 1/259) |
| 26 | Excavation for foundation / pipe trenches in hard murum and boulders, W.B.M. road including removing the excavated material upto a distance of 50 M beyond the area and lifts as below, stacking and spreading as directed by Engineer-in-charge, normal dewatering, preparing the bed for foundation and excluding backfilling, etc. complete. (BdA-3/259) |
| 27 | Excavation for foundation / pipe trenches in soft rock and old cement and lime masonry foundation asphalt road including removing the excavated material upto a distance of 50 M beyond the area and lifts as below, stacking as directed by Engineer-incharge, normal dewatering, preparing the bed for foundation and excluding backfilling, etc. complete. (Bd-A-4/259) |
| 28 | Excavation for foundation / pipe trenches in hard rock and concrete road by chiselling, wedging, line drilling by mechanical means or by all means other than blasting including trimming and levelling the bed, removing the excavated material upto a distance of 50 metres beyond the area and lifts as below, stacking as directed by Engineer-in-charge, normal dewatering, excluding backfilling, etc. complete by all means. (Bd-A-6/259) |
| 29 | Filling in plinth and floors murum bedding in trenches with approved murum from excavated materials from foundation in 15 cm to 20 cm layers including watering and compaction, etc. complete. (Bd-A-10/263) |
| 30 | Lowering, Laying and Jointing H. D. P. E./M.D. P. E. pipes in proper position including all specials by compression fitting/electrofusion and butt fusion jointing procedure as per relevent IS Code complete with all materials for jointing procedure like Electrofusion machine, Electric heater/butt fusion welding machine with hydraulic jack, top loading clamp etc. and all labours as directed by engineer in charge as per IS-7634 Part II 90mm dia HDPE PN 8 |
| 31 | Lowering, laying and jointing in position following C.I.D/F Reflex valves, Butterfly valves and Sluice valves including cost of all labour jointing material, including nut bolts and giving satisfactory hydraulic testing etc. complete. (Rate for all class of valves.) sluice valve 100mm dia |
| 32 | Lowering laying and jointing in position following C.I.D/F Reflux valves Butterfly valves and sluice valves including cost of all labour joining material, including not bolts and giving satisfactory hydraulic testing etc. complete. (Rate for all class of sluice valves) sluice valve 100mm dia |
| 33 | Lowering, laying and fixing in proper alignment and position all types of C.I. air valves as directed by Engineer-in-charge including cost of conveyance from stores to site of work, cost of all material and giving satisfactory hydraulic testing, etc. complete. (for all class of valves) air valve 25mm dia |
| 34 | Providing and fixing in position air valve shaft including providing and fixing GI Medium Class or 6 mm thick M.S. pipe shaft 2.70 M long over branch flange of air valve tee, providing PCC block of M-150 concrete, 150 mm thick around the air valve tee including encasing of vertical shaft in PCC M150 as shown in type design together with providing and making flanged joints wherever required and fixing of air valve tee, etc. complete as per type design and as directed by Engineer -in- charge for following diameters of pipe lines (type design attached.) upto 150mm |
| 35 | Providing and laying in situ Cement Concrete of trap/ granite / quartzite /gneiss metal for RCC work in foundation like raft, grillage, strip foundation and footing of RCC columns and steel stanchions including normal dewatering,form work, compaction, finishing and curing, etc. complete. (By weigh batching and mix design for M250 and M-300 only. Use of L&T, A.C.C., Ambuja, Birla Gold, Manikgad, Rajashree, etc. cement is permitted.) (Excluding M.S. or Tor reinforcement) 1:2:4 M15 grade encasing |
| 36 | Providing and constructing B.B. masonry valve chamber with 15 cm thick 1:3:6 proportion PCC bedding, excluding excavation, B.B. masonry in CM 1:5 proportion precast RCC frame and cover, etc. complete as directed by Engineer-in-charge. As above 90x60 cm |
| 37 | Refilling the trenches with available excavated stuff with soft material first over pipeline and then hard material in 15 cm layers with all leads and lifts including consolidation, surcharging, etc. complete |
| 38 | Hydraulic testing of H. D. P. E./ M. D. P. E./D.I. pipe line to specified pressure including cost of all materials and labour and water for testing for specified length including cutting, placing end cap making arrangement for filling safe water using reciprocating type pumps which should be able to provide specified test pressure gauges and other necessary equipments, labour, operation charges, etc. required for testing. The rate under this item shall also include cost of retesting, if necessary and reinstating to original position. 90mm dia HDPE PN 8 Pipes |
| 39 | MSEB Please Enable Macros to View BoQ information |
