|
| 1 | S& F powder coated (minimum thickness 50 microns powder coating) extruded aluminium glazing/ doors & shutters made out of section 63.5x38.10x1.29mm for chowkats or frame & shutters made of size 44.45x44.45x1.29mm for side rails and middle rail, 114.3X44.45X1.29mm for top rails and bottom rails and including 12mm thick High Density Fibre Board pre-laminated on both sides (water proof) below middle/lock rail and 5mm thick tinted glass i.e tempered/ laminated/plain /glazed above middle/lock rail and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beads 20mm size with and incl mortice lock with duplicate keys, hydraulic door closer/floor spring etc complete all as specified and directed approved by accepting officer including supply and fixing the following items and taking down of old existing door shutter with frame of any nature and any size:(a) Stainless Steel (304 Grade) Finished Butt Hinges 150mm - 3 nos per leaf.(b) Powder Coated Aluminium Tower Bolt 200mm long - 2 nos per leaf(c) Powder Coated Aluminium Handles 150 mm - 2 nos per leaf |
| 2 | Providing and fixing powder coated 50 microns extruded aluminium in 3 Tier Track Sliding Windows/glazing, with frame of section 100x44-45x1.30mm, track of size 100x38.10x1.30 & shutters made of size 32x18x1.3mm, with and including 4mm thick tinted sheet glass selected quality fixed in 2 shutters and stainless steel wire gauge 0.36mm nominal dia of wire and average width of aperture 1.40mm in one shutter and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beeds 20mm size and also including powder coated 150mm handle with built in locking system for each leaf complete all as specified.and taking down of old existing window shutter with frame of any nature and any size:Mode of measurments :- ( Clear opening will be measured ) |
| 3 | Powder coated 50 microns extruded aluminium frame for fixed type partition (Standard two panel pattern) made out of powder coated aluminium section of size 63.5 x 38.10 x 1.5mm, comprising of 5mm thick tinted glass inserted in and including necesary jointing cleats, rubber packing, anodised aluminium snap beading complete fixed to floor and wall by means of cadium plated steel screws complete incl taking down of existing partition with all fittings and fixtures all as specified and directed. |
| 4 | S & F Door closer hydraulically regulated designation No 3 universal type suitable for door shutter 851mm to 1000mm vide and weight between 61 to 80 kg of aluminium (extruded section body) as in repairs all as specified and directed. |
| 5 | S & F in repair Double action floor spring ISI marked hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed in repairs complete all as specified. |
| 6 | Dismantling wall and ceiling boarding of any description, thickness including cover fillets complete al as specified and directed. |
| 7 | M&L for providing & fixing 12mm thick gypsum baord in celing (two or three stages if reqd) including GI U-section 50mmx35mmx7mm & edge side GI U-section size 30mmx25mmx15mmx7mm fixed with screw gypsum board and frame grid suspended with soffit cleat to roof slab for hanging 4mm dia GI hanger rod with adjustable level clips, after fixing of gypsum board jonits/junction of gypsum board ceiling to be covered with 50mm to 100mm corner strips, Round at fan & lights, cut for cassette AC indoor unit , light and Gypsum cornice all around the wall of any design and size as requried by user complete all as specified and as per manufacture's instruction and applying two coats of Luster Paint over 3 mm POP to visible side of gypsum board ceiling shade/tint and including necessary scaffolding for the work complete and dismantling of old existing false ceiling of any nature all as specified and directed by Engr-in-Charge |
| 8 | M & L for Seamless calcium silicate ceiling 8mm thick made out of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25 mm long self drilling and tapping screws having phillips head with under head cutter at 200 mm centre to centre, including finshing the joint of face board with specially formulated jointing compound and 48 mm wide fibre tape to provide seam less finish |
| 9 | M &L For false ceiling with 4 mm thick designer 'E' board fixed on GI grid work with powder coated finish on exposed surface of size 0.60 x 0.60 m consisting of GI angle supported on wall of size 24 mm x 28 mm x 0.7 mm main tee of size 24 mm x 38 mm x 0.7 mm cross tee of size 24 mm x 28 mm x 0.7 mm using porpose made members interlocking to made to shape at 1200 mm c/c fixed with 3mm dia. GI wire suspender and making holes etc. all as directed including two coats of white wash on ceiling after preparation of surfaces and as per manufacture instruction make of grid work : Armstrong/ swastik/ Techno Grid and 'E' board Gypsum or equivalent approved. including taking down old ceiling etc complete as directed.Note :- The rate quoted by the bidder is including necessary scafolding for the work |
| 10 | S & F Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing atsite on PVC frame complete all respect including supply and fixing of all accessories like fasteners/screws/solvent etc all as recommended by manufacturer all as specified (colour/pattern as approved by Accepting Officer). |
| 11 | S&F of 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing. |
| 12 | Demolition of stone slabs and tiles laid, bedded and pointed in any mortar of any description or thickness in floors, aprons etc complete all as specified and as as directed. |
| 13 | Demolition of cement concrete un -reinforced in ground floors and pavings n.exc 15cm thickness complete all as specified. |
| 14 | M & L for 75 mm thick cement concrete 1:4:8 type D2 using 40mm graded stone aggregate as in subbase of flooring / hard standing as specified |
| 15 | M&L for 25mm thick cement concrete type B-1, 1:2:4 (20mm grade aggregate) as in levelling coarse in flooring finished even and fair under floor finishes. |
| 16 | M & L for vitrified Ceramic tiles 8 to 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etc over 20 mm thick screed bed in CM (1:4) complete as directd.and including dismantling of old existing tiles of any thickness and nature |
| 17 | M & L for vitrified Ceramic tiles 8 to10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etc including 10mm thick backing coat in CM 1:3 and dismantling of old tiles along with cement mortar bedding complete as directd. |
| 18 | M & L for vitrified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matchetc over 20 mm thick screed bed in CM (1:4) complete as directd.and including dismantling of old existing tiles of any thickness and nature |
| 19 | M & L for vitrified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick backing coat in CM 1:3 and dismantling of old tiles along with cement mortar bedding complete as directd. |
| 20 | M & L for complete removal of existing treatment and Applying two coat of oil bond distemper over a coat of alkali resistance primer over a coat of wall care putty (to an average thickness of 1mm )thick including necessary scaffolding arrangement for any height as required at site all as specified and directed. |
| 21 | M & L for Granite of black / green / imperial red (colour as approved by Accepting Officer) of any type machine cut as in shelves/steps/counter tops, 20 mm thick, set and jointed in cement slurry over & including screed of 15 mm thick / rendering in cement mortar (1:4) and pointed in cement mixed with pigment to match the shade of slab or with suitable adhesive for fixing on unpolished kota stone slabs and including rubbing, cutting and mirror type polishing and bull nose on exposed sides complete all as specified .Note : Single piece should be used in steps/cills/jambs/shelves or equivalent as approved by accepting officer . |
| 22 | Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified. |
| 23 | M & L for Machine cut kota stone slab flooring 20-25mm thick over, laid over cement screed base , jointed and pointed with grey cement slurry mixed with pigment over 20mm thick cement mortar 1:6 screed bed to match the shade of the slab including rubbing and polishing complete all as specified and directed. Note : Work will be in patches or in bulk |
| 24 | M & L for Machine cut kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar over 10 mm thick cement plaster 1:3 jointed and pointed with grey cement slurry mxed with pigment to match the shade of the slab including rubbing and polishing complete, all as specified and directed. |
| 25 | Demolition of brickwork or stone, PCC block, boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc, but excluding ashlars facings, dressed stone work and precast concrete articles complete all as specified and as directed. |
| 26 | M & L for precast cement concrete solid block masonry exc 10cm in width and setting in CM 1:6 type C1, 1:3:6 all as specified. |
| 27 | M&L for rendering 15mm thick in CM (1:6) on on stone masonry surfaces or surface other than fair face of brick-work or on one side of lathing surfaces, trowelled to even and fair finish without using extra cement including taking down of old plaster of any thickness complete all as specified and directed. |
| 28 | M&L preparing newly plastered surfaces of wall and applying complete wall with POP/Birla putty and making smooth surfaces and applying two coats of Oil bound distemper over a coat of primer all as specified and directed by Engineer-in-Charge. |
| 29 | S & F toughned glass 10mm thick as in hinged doors, partitions automatic doors and similar work including cutting to shape, drilling holes with all accessories like handle, stopper with glazing with beads fixed with metal panel pins (beads to be measured separately as 'supplied only') as required including hacking out out glass |
| 30 | S & F Venetian blinds screen fabric with 5% openness factor roller type for windows of colour/shade as approved by Ac cepting Officer complete fixed in position inclusive S&F of all accessories and hardwares for fixing and operation, all as recommended by manufacturer, all as specified incl taking down old curtain rods of any type complete. |
| 31 | S & F Venetian blinds screen fabric with 5% openness factor roman type for windows of colour/shade as approved by Ac cepting Officer complete fixed in position inclusive S&F of all accessories and hardwares for fixing and operation, all as recommended by manufacturer, all as specified incl taking down old curtain rods of any type complete. |
| 32 | S&F of stainless steel tubing of 25 mm dia chromium plated min. 1.0 mm wall thickness as in curtain rod complete incl S&F 02 Nos stainless steel brackets/finials fency type, stops fixed with ss screws etc all as specified & directed as in repair .Note : For the purpose of mesurement and payment running length of curtain rod only shall be considered as approved by accepting officer. Please Enable Macros to View BoQ information |
