|
| 1 | Civil Work |
| 2 | Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. All kinds of soils |
| 3 | Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering All work up to plinth level, M10 grade Nominal Mix 1: 3: 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size). |
| 4 | Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. M20 grade Nominal Mix 1: 1.5: 3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size). |
| 5 | Laying of lawns including ploughing leveling breaking of clods manuring and removal of stones etc. (cost of manure or extra good earth to be paid separately )maintenance of lawn foe 30 days or more till the grass forms a thick lawns free from weeds and fit for moving in the duration of planting if lawn die some where the contractor will replant it at his own costin rows 5 cm apart in either direction |
| 6 | Providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats,or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide |
| 7 | Supplying, erecting and fixing in position specified precast RCC bench made of RCC grade M-30 consisting of 2 Nos. “L” shaped base support of thickness 100 mm back height 1000mm, front height 450 mm, base width 420mm and 5 Nos. RCC planks of size of 1500x100 x 50 mm and 1 Nos RCC planks of 150x200x50mm including joining all parts with galvanised nuts and bolts of suitable size. All bolts to be sealed after assembly with nice finish and appearance and level complete in all respect as per direction of engineer in-charge. Every bench should have a manufacturer’s logo of appropriate size Engraved at suitable place. |
| 8 | \\"Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : \\"Two or more coats on new work |
| 9 | Painting exterior surface of Wall with 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of base with sand papering, primer, putty, etc complete in all respect including scaffolding and safety provision Old Work |
| 10 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement in position to the required line, level and curvature jointed with cement mortar 1:3 (1 cement : 3 coarse sand ) including making joints with without grooves (thickness of joints except at sharp curve shall not to more than 5mm) including making drainage opening wherever required complete including painting etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineerin- charge). |
| 11 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes (IS 15778 : 2007 code) having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings, this included jointing of pipes & fittings with one step CPVC solvent cement , trenching refilling & testing of joints complete as per direction of Engineer in Charge.(External work).25 mm nominal size |
| 12 | P & F Bib Cock (IS : 8931 Mark), Superior quality of approved make:Brass 400 gm,15mm nominal bore. |
| 13 | P & F Full-way Valve (IS:778 Mark) or wheel valve of approved make :Gun-metal 25mm nominal bore. |
| 14 | Providing and fixing stainless steel railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).Grade 304 |
| 15 | Tubewell |
| 16 | Construction of tube-well from ground levels and upto 100 Meter depth and above to accommodate housing and assembly pipe of following sizes in all types of alluvium strata by percussion/ rotary drilling method and with gravel as per IS:4097-1967 and packing as per IS:2800 (Part I -& II) 1979 as amended upto date (the work includes the cost of gravel & its primary packing and packing during development, lowering of housing & strainer assembly pipes, with supply and wrapping of coir-rope, wherever necessary, for arresting fine sand particles. The work will not include cost of housing pipe and strainer pipe assembly and development work, but work would be completed after obtaining sand free water). 200mm nominal bore. |
| 17 | Construction of Tube-well upto 100 Meter depth and above in all type of rocks by DTH system and over burden, to accommodate casing pipe of following sizes in all types of soils and over burden including lowering of casing pipes, but excluding cost of casing pipes as per IS : 2800 (Part I & II) 1979 specifications. The work would be completed after obtaining sand free water. The tube well should have a throughout bore as per nominal dia of casing pipe: 200 mm dia nominal bore |
| 18 | Development of tube well as per IS specification using suitable compressor to give sand free water for required yield of the gravel packed tube well. |
| 19 | Supply of ERW M.S. black casing pipe ISI marked (IS:4270/1992) of grade Fe410 of following sizes at site of work. 200 mm nominal bore |
| 20 | Supply of strainer pipes made of ERW M.S. black pipe ISI mark of following sizes at the site of work including required size of slotting as per IS:8110-1985. 200mm Nominal Bore. |
| 21 | S & F tube well cover of M.S.sheet (6mm thick) with nuts and bolts complete for casing size: 200 mm dia. |
| 22 | S & F M.S. clamp, set of 50 ×6mm flat iron with nuts and bolts etc. for holding the riser pipe assembly of submersible pump set. |
| 23 | Providing & lowering of G.I. Pipes, flange pipe including rubber washer and nuts of 8 mm dia complete in all respect I.S.1239 Marked. B class 50 mm Dia |
| 24 | SITC of Radial / mixed flow ISI marked water and anti-corrosive liquid filled submersible motor pump sets suitable for 100/150mm dia borewell. The size of adopter fixed on top of the motor should exceed the top of coupler , for safegaurd the coupler. The construction material of motor and pump should match IS: 8034 : 2018 and IS: 9283 guideline. The radial flow pumpset should operate at 5 star energy efficiency level of BEE and mixed flow pump set should operate at 3 star energy level of BEE, accompained by valid BEE certificate. Motor should be IE2 class as per IEC 60034-2-1: 2007, IEC 60034-30: 2008, & IS12615:2011 with required accessories including making connection suitable for Bore well. The job includes labour part of lowering of riser pipe G.I./ H.D.P.E. with rope, cables & pump, installation of complete fitting and accessories, jointing of electrical cables up to Starter. All labour for testing of submersible pumps set and supply of water to water mains, complete in all respect. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test certificate before execution. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . 150 mm diameter Submersible pump shall have following HP Rating, phase, Head range, Discharge range respectively.10.0 HP, 3-Ø, (91 - 115)Mtr, (285-180) LPM |
| 25 | P/Laying ISI marked P.V.C. insulated submersible cable confirming to(IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.90 % purity copper, stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, existing pipe / open trench / Cable tray / on surface including making connection etc. as required. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR6.0 Sq.mm 3 core flat / Round |
| 26 | Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Armoured Copper cable confirming to IS:1554 P-I / IS :7098 P - I of 1.1 KV with electrolytic grade Copper made of copper rods confirming to IS 613-1964, of purity >99.7 %, round / flat strip armouring, Inner / outer sheath confirming to IS:5831 in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray(with cable tie) including testing etc. as required of following size. OEM must have it's own in house NABL accrediated Laboratory for testing procedure as per IS:10810 For additional technical parameters of product / work refer Annexure 'A' attached with this BSR6.0 Sq. mm - 3 Core |
| 27 | SITC of Contactor OEM Fabricated DOL/Star-Delta Starter panel with switchgear selection as per Type-2 Cordinatiom Chart and made out from 1.6 mm thick powder coated CRCA sheet, enclosure comprising of over load protection relay, short circuit & single phasing protection, Illuminated ON / OFF push buttons, ammeter, voltmeter, indicating lamps etc. suitable for following rating motors complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . For Three phase Submersible / Mono block pump 7.5 HP to 10.0 HP ( Star / Delta starter ) |
| 28 | Un-lowering of submersible pump set with all piping from a tube-well/ open-well complete (labour charge only ) including transportation of tripod, chain, pulley-block and other materials required and lowering of repaired/ new pump in the tube-well / open-well complete in all respect. |
| 29 | Open Air Gym Equipment |
| 30 | SURFING BOARD |
| 31 | Providing and fixing of Surfing Board of size 1000mm (Length) x 600mm (Width) x 1400mm.(Height) fabricated with the main frame of 80mm NB shall be made from “C” class G.I. pipe.The bottom support shall be welded of M.S. plate of Ø 250 mm & 10mm thickness. The handle frame of 25NB shall be made from “C” class G.I. pipe. The foundation should be used for fixing is a structure and shall bemade from center pipe of G.I. of 80NB “C” class welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe shall be supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. Bushes shall be used of 70mm Outer Diameter with 5mm thickness. The footrests shall be made from high quality fiber reinforced plastic. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. The pins to be used shall be made up of Ø35 mm SAE 8620 bright material. The bearing shall be used are of “6007zz” permanent lubricated sealed bearing of reputed brand (SKF/FAG). High tensile steel with galvanized nut bolts shall be used for assembly. The cerclips shall be used for assembly is of A34. The powder coating shall be done with Pure Polyester powder of Ackzonoble or Berger with minimum 60 to 70 micron thickness. Design as per Sansun Model no. OG01 (Photo enclosed), all complete under directions of Engineer-in-charge. (The cement concrete and excavation work shall be paid separately). |
| 32 | CROSS TRAINER |
| 33 | Providing and fixing of Cross trainer of size 1320mm (Length) x 600mm (Width) x 1750mm. (Height) fabricated with the main frame Pipes of 80NB shall be made of “C” Class G.I and pipe with single bend pipe with 250mm radius. The bottom support of M.S. round plate of Ø250 mm & 10mm thick. The Handle Frame shall be made up of 25NB “C” Class G.I. Pipe. The foundation should be used for fixing is a structure and shall be made from center pipe of G.I. pipe of 80 NB “C” class welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe should be supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm and CRC square pipes of 3mm thickness. To build structure bushes to be used which shall be made from M.S.seamless pipe of 60mm OD with 5 mm thickness. The footrests shall be made from Aluminum casting material of size 130 mm X 310mmX5mm thickness and mounted on M.S. Plate of Size 130mmx310mmx3mm thick. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. Pins to be used of Diameter 35mm, 25mm, and 17mm shall be made up from SAE 8620 bright . The Bearings shall be used of “6007zz” “6205zz” and “6203zz” permanent lubricated sealed bearing of reputed brand (SKF/FAG). High tensile steel with galvanized nuts and bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powders of Ackzonoble or Berger Paints with 60 to 70 Micron thickness. A16 , A 24 mm circlips shall be used for assembly. Bolt M8X16 mm and NY lock nut of M8 shall be made of SS 304 used on nylon cap mounted on pins to protect bearings and pins from rain and dust. Design as per Sansun Model no. OG02 (Photo enclosed), all complete under directions of Engineer-in-charge. (The cement concrete and excavation work shall be paid separately). |
| 34 | THAI-CHI SPINNER (2 WHEEL) |
| 35 | Providing and fixing of Thi-Chi spinner (2 Wheel) of size 700mm (Length) x 1000mm (Width) x 1280mm (Height) fabricated with a center pipe of 100NB shall be made up of “C” Class G.I. pipe. The handle movement round frame shall be made up from 25 NB “C” class G.I. pipe. The foundation should be used for fixing is a structure and shall be made from center pipe of G.I. of 80 NB “C” class, welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe shall be supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. The pins to be used shall be made up of Ø 25 mm of SAE8620 bright material. The bearing shall be used of “6201zz” & “6205zz” permanent lubricated sealed bearing of reputed brand (SKF/FAG). High tensile S.S. nut bolts shall be used for assembly. Foundation cover Closing Cap shall be made from FRP Material with 0.7 mm thickness. The cerclips used for assembly shall be of of A24 and A11. The nylon bush shall be used for handle knob. The powder coating shall be done with pure Polyester powders from Ackzonoble or Berger Paints with 60 to 70 micron thickness. Bolt M8X16 mm and Nylock nut of M8 shall be made of SS 304 used on nylon cap mounted on pins to protect bearings and pins from rain and dust. Design as per Sansun Model no.OG05 (Photo enclosed), all complete under directions of Engineer-in-charge. (The cement concrete and excavation work shall be paid separately). |
| 36 | SEATED PULLER |
| 37 | Providing and fixing of Seated Puller of size 1900mm (Length) x 740mm (Width) x 1920mm. (Height) fabricated with a center pipe is of 100NB shall be made from “C” Class G.I. pipe. Bottom support of M.S. round plate of Ø 250 mm & 10mm thickness shall be welded. All linkages shall be made up of 25NB “C” class G.I. pipe. The handle frame of 32NB “C” class G.I. pipe. The seat frame of 32NB “C” class G.I. pipe, To build structure bushes to be used which shall be made from seamless pipe of 60mm O.D. and 5mm thickness as well as 60mm diameter solid bar bush shall be used. The foundation should be used for fixing is a structure and shall be made from center pipe of G.I. of 80 NB “C” class welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe shall be supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. Foundation cover Closing Cap shall be made from FRP Material. The seats and Back rests to be fitted on the outer frames shall be made up of M.S. Sheet of size 330 mm X 300 mmX2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. Pins to be used of Diameter 25mm and 17mm shall be made up from SAE 8620 bright material. The bearings shall be used of “ 6205zz” and “6203zz” permanent lubricated sealed bearing of reputed brand (SKF/FAG). High tensile steel with galvanized nuts & bolts shall be used for assembly. The cerclips to be used for assembly are of A16 The powder coating shall be done with Pure Polyester powders of Ackzonoble or Berger Paints with 60 to 70 micron thickness. Design as per Sansun Model no. OG06 (Photo enclosed), all complete under directions of Engineer-in-charge. (The cement concrete and excavation work shall be paid separately). |
| 38 | LEG PRESS |
| 39 | Providing and fixing of Leg Press of size 1840mm (Length) x 360mm (Width) x 1560mm. (Height) fabricated with a center pipe of 100mm NB shall be made from “C” Class G.I. pipe. The Sleeve frame of 100 OD and of M.S. Seamless Pipe with thickness 5mm. This sleeve should be disassembled from main frame. The bottom support shall be made up of M.S. round plate of Ø250 mm & 10mm thick. The remaining outer frame of 32NB shall be made from “C” class G.I. pipe. The foundation should be used for fixing is a structure and shall be made from center pipe of G.I. of 80mm. NB “C” class welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe shall be supported with 25 mm X 25mm M.S. angle of 3 mm thickness and 20mm x 40mm CRC square pipe of 3mm thickness. Seat & Back rest to be provided shall be made up of MS deep draw quantity of 2mm thickness with no joint with uniform outer edge radius 20mm. The footrests shall be made from casted Aluminum material, having sizes 130mm X 310mm X 5mm thick. With the support of 310mm X 130mm X 3mm thick MS plate. The frame of footrests shall be made up of 25 NB “C” class G.I. pipe. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. To build structure bushes to be used which shall be made from M.S. seamless pipe of 50mm O.D. and 5mm thickness. The pins to be used shall be made up of Ø25 mm SAE 8620 bright material. The bearings shall be used are of “6205zz” permanent lubricated sealed bearing of reputed Brand (SKF/FAG). High tensile steel with galvanized nut bolts shall be used for assembly. The cerclips shall be used for assembly are of A24 mm. The powder coating shall be done with Pure Polyester powder of Ackzonoble or Berger with 60 to 70 micron thickness. Design as per Sansun Model no. OG07 (Photo enclosed), all complete under directions of Engineer-in-charge.(The cement concrete and excavation work shall be paid separately). |
| 40 | CHEST PRESS |
| 41 | Providing and fixing of Chest Press of size 2000mm (Length) x 710mm (Width) x 2200mm. (Height) fabricated with the center pipe of 100NB shall be made up of “C” Class G.I. pipe. The bottom shall be welded with support of M.S. round plate of Ø250 mm & 10mm thickness. The connecting pipes shall be made up from 25NB “C” class G.I. pipe. The handle frame shall be made up from 32NB “C” class G.I. pipe. To build structure bushes to be used which shall be made from MS seamless pipe of 60mm O.D. and 5mm thickness as well as 60mm diameter solid bar bush shall be used. The foundation should be used for fixing is a structure and shall be made from center pipe of G.I. of 80 NB “C” class welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe shall be supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. The seats and Back rests to be fitted on the outer frames shall be made up of M.S. Sheet of size 330mm X 300 mmX2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. Foundation cover Closing Cap shall be made from FRP Material with 0.7 thickness. Pins to be used of Diameter 25mm and 17mm shall be made up from SAE 8620 bright material. Bolt M8X16 mm and Nylock nut of M8 shall be made of SS 304 used on nylon cap mounted on pins to protect bearings and pins from rain and dust. The bearings shall be used are of “6205zz” & “6203zz” permanent lubricated sealed bearing of reputed brand (SKF/FAG). High tensile steel with galvanized nuts & bolts shall be used for assembly. The cerclips to be used for locking shall be made up of A24 mm & A16mm. The powder coating shall be done with Pure Polyester powders from Ackzonoble or Berger Paints with 60 to 70 micron thickness. Design as per Sansun Model no. OG14 (Photo enclosed), all complete under directions of Engineer-in-charge. (The cement concrete and excavation work shall be paid separately). |
| 42 | DOUBLE STANDING TWISTER |
| 43 | Providing and fixing of Double Twister Standing of size 1500mm (Length) x 600mm (Width) x 1300mm. (Height) fabricated with a Center Pipe of 100NBshall be made from “C” Class G.I. material. The bottom shall be welded with support of M.S. round plate of Ø250 mm & 10mm thickness. The bottom frame of 32NB shall be made from “C” class G.I. pipe. The handle frame of 25NB shall be made from “C” class G.I. pipe. The foundation should be used for fixing is a structure and shall be made from center pipe of G.I. of 80 NB”C” class welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe shall be supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. The Twister plate to be fitted on the bottom frame shall be made up of M.S. Round Plate of size Ø300mm and 10mm thick. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. Pins to be used of Diameter 35 mm shall be made up from SAE 8620 bright material. The bearings shall be used are of “6205zz” permanent lubricated sealed bearing of reputed. Brand. High tensile steel with galvanized nuts and bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powders from Ackzonoble or Berger Paints with 60 to 70 micron thickness. Design as per Sansun Model no. OG17 (Photo enclosed), all complete under directions of Engineer-in-charge. (The cement concrete and excavation work shall be paid separately). |
| 44 | CHEST CUM SHOULDER PRESS |
| 45 | Providing and fixing of Chest Press Cum Seated Puller of size 2000mm (Length) x 710mm (Width) x 2200mm (Height) fabricated with the handle frame made up from 32NB “C” class G.I. pipe.To build structure bushes to be used which shall be made from seamless pipe of 50mm O.D. and 6mm thickness as well as 50mm diameter solid bar shall be used. The foundation should be used for fixing is a structure and shall be made from center pipe of G.I. of 80 NB “C” class welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipeshall be supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. The seats and Back rests to be fitted on the outer frames shall be made up of M.S. Sheet of size 330 mm X 300 mmX2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. Pins to be used of Diameter 25mm and 17mm shall be made up from SAE 8620 bright material. The bearings shall be used are of “6205zz” & “6203zz” permanent lubricated sealed bearing of reputed brand (SKF/FAG).High tensile steel with galvanized nuts & bolts shall be used for assembly. The cerclips to be used for locking shall be made up of A24 & A16 The powder coating shall be done with Pure Polyester powders from Ackzonoble or Berger Paints with 60 to 70 micron thickness. Design as per Sansun Model no. OG20 (Photo enclosed), all complete under directions of Engineer-in-charge. (The cement concrete and excavation work shall be paid separately). |
| 46 | Supply and fixing of Instruction board of size 4'x 6' made of digital vinyl print with gloss lamination & pasted on 3mm ACP sheet fixed over 2.0 mm thick MS sheet, framed on 32 mm dia MS pipe, supported on 50mm dia MS pipe which goes 600mm below ground level with hold fast including welding and painting.Design and drawing all complete under directions of Engineer-in-charge. (The cement concrete and excavation work shall be paid separately). |
| 47 | Annual Maintenance of all open air gym equipments fixed at Central Park, Vigyan Nagar Alwar for a period of 3 years (After one year free maintenance) including replacing of any or all damaged parts and running satisfactory in all respect. |
| 48 | Playing Equipments |
| 49 | Providing & installation of Arihant playtime, Uday creation Kilkari or its equivalent FRP Double roller slide with following specification Specification for :- FRP DOUBLE ROLLER SLIDERec. Age :- 4 – 12 yrs.The area :- 5.2 m x 4.2 m Safe play area :- 6.7 m x 5.7 m Height :- 2.1 m / 1.5 mThe exciting double roller slide is made up of Fibreglass Reinforced Plastic. The most attractive and enjoyable of its kind, the chute of this slide consists of molded plastic rollers spreaded over the length. Rollers are made up of HDPE with UV stabilized pigment. The trapezium platform of the slide is made up of the fiberglass reinforced plastic. The vertical platform support pipes used are of 80 NB powder coated GI pipes. The railing is made in rotational molding. The slide entry is made up of 20 NB powder coated GI pipes. The slide entry is mounted on 80 NB and 80x20 NB nylon clamp. The ladder frame is made in 20 NB and 25 NB powder coated GI pipes. The triangular steps are made in 16 SWG GI sheets. |
| 50 | Providing & installation of Arihant playtime, Uday creation Kilkari or its equivalent four seater arch swing with following specification Specification for :- FOUR SEATER ARCH SWINGRec. Age :- 4-14 yrs.The area :- 6.0 m x 1.5 mSafe play area :- 7 m x 3.5 mAs the name suggests 04 children can enjoy the swing at one time. The arched shaped side frame is made of 80 NB GI pipes and top pipe is made up of 50 NB GI pipes. The frame is powder coated to give an esthetic look. The four swings are made up of 10 mm thick anti skid chequered reinforced rubber top. The rubber belt seat is suspended on 6 mm rubber coated GI chain. The ball bearings are mounted inside a specially designed nylon clamp. |
| 51 | Providing & installation of Arihant playtime, Uday creation Kilkari or its equivalent Circular Swing with following specificationSpecification for :- CIRCULAR SWING Rec. Age :- 3 - 10 yrs.The area :- 1.5 m x 2 mSafe play area :- 2.5 m x 3 mThe leg support of this item is made up of 40 nb, while the top bar is from 50 nb powder coated gi pipes. The swing frame is made from 25 nb and 15 nb powder coated gi pipes. There are two seats provided which are made out of molded plastic in roto moulding process. The platform is made using aluminum chequered plate for footrest and bearing assembly is made |
| 52 | Horticulture |
| 53 | Irrigation of lawn |
| 54 | Uprooting weeds from the lawn plots and trenched area after 10 to 15 days of its flooding with including disposal of uprooted vegetation |
| 55 | Sweeping / cleaning of gardens roads lawns paths and disposal of all rubbish |
| 56 | Moving manually / with power machines with power machine Please Enable Macros to View BoQ information |
