|
| 1 | Dismantling of existing structures like culvert, bridges, retaining walls and other structures comprising of brick masonary, including disposal of unserviceable material and stacking the serviceable material with all lift and lead of 1000 m as per Technical Specification Clause 202 (B)-in cement mortar Ref. to MORD-202(2.6) |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the All kinds of soil. Rate as per DAR 2.8.1 |
| 3 | Providing and laying in position cement concrete 1:4:8 (1cement, 4 coarse sand (zone-III), 8 graded stone aggregate 40 mm Nominal Size) excluding the cost of centering and shuttering- All work upto plinth level as per PWD (SCH.)- 273 Ref. to DAR 4.1.8 |
| 4 | Brick work with common burnt clay (non modular) bricks of class 150 in foundation and plinth in Cement mortar 1:4 (1 cement : 4 coarse sand) as per DAR 6.1.1. |
| 5 | Construction of granular sub-base by providing well-graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification clause 401. |
| 6 | Construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days, using curing compound (where specified) and water finishing to lines and grade as per drawing and Technical Specification Clause 1501 |
| 7 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering in 1:2:4 (1 cement: 2 coarse sand (zone- III): 4 graded stone aggregate 20mm nominal size). All work upto plinth level Ref. to DAR 4.1.3 |
| 8 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement. 1:1.5:3 (1 cement: 1.5 coarse sand (zone- III): 3 graded stone aggregate 20mm- All work up to plinth level. Ref. To DAR 5.1.2 |
| 9 | 12mm cement plaster finished with a floating coat of neat cement of mix : 1:4 (1 cement: 4 fine sand) Ref. to DAR 13.7.2 |
| 10 | Mild steel or iron in plain work such as reinforced concrete or reinforced brick work (when not included in an overall rates) wrought to required shape as necessary including bending for proper completion of work and including supply of all steel and wastages and overlapping and hookes as per Chap-10, SCH. P.W.D./D.S.R. 504 Please Enable Macros to View BoQ information |
