|
| 1 | Taking down CI soil/waste/vent/rain water pipes of any diameter including all fittings such as shoes, bends, swan necks, offsets, access doors, heads or gratings etc., carefully dismantled from walls or ceilings, including making good disturbed surfaces to match the existing, complete all as specified and directed. |
| 2 | Supply and fixing cast iron (CI) soil/waste/vent pipe, sand cast, 100 mm bore, with ears in any length, fixed to walls with cement joints including necessary clamps, holder bats, cutting and making good to walls/floors where required, complete all as specified and directed. |
| 3 | Ditto all as per item 2 above but except pipe complete all as specified and directed. |
| 4 | Supply and fixing cast iron (CI) soil/waste/vent pipe, sand cast, 75 mm bore, with ears in any length, fixed to walls with cement joints including necessary clamps, holder bats, cutting and making good to walls/floors where required, complete all as specified and directed. |
| 5 | Ditto all as per item 4 above but except pipe complete all as specified and directed. |
| 6 | Supply and fixing cast iron (CI) bends (any radius) for soil/waste pipes 100 mm bore, including diminishing pieces or tapers, fixed on walls with cement joints, complete all as specified and directed. |
| 7 | Supply and fixing cast iron (CI) bends (any radius) for soil/waste pipes 75 mm bore, including diminishing pieces or tapers, fixed on walls with cement joints, complete all as specified and directed. |
| 8 | Supply and fixing cast iron (CI) branch pieces, single (equal or unequal), ordinary or inverted, spigot and socket type, with parallel branches for 100 mm bore soil/waste pipe (Y or T pattern), complete all as specified and directed. |
| 9 | Supply and fixing cast iron (CI) branch pieces, single (equal or unequal), ordinary or inverted, spigot and socket type, with parallel branches for 75 mm bore soil/waste pipe (Y or T pattern), complete all as specified and directed. |
| 10 | Supply and fixing 100 mm bore cast iron sanitary connection socket to fit WC outlet, complete all as specified and directed. |
| 11 | Taking down cement plaster of any description, including raking out joints, hacking for key, and scrubbing down with water, complete all as specified and directed. |
| 12 | Material and labour for rendering 15 mm thick in cement mortar (CM) 1:6 on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement, complete all as specified and directed. |
| 13 | All as per Item No. 12 above, but 5 mm thick in cement mortar (CM) 1:3 on concrete ceiling surfaces, finished even and smooth without using extra cement, complete all as specified and directed. |
| 14 | Material and labour for plastering 20 mm thick in cement mortar (CM) 1:4 on brick work or concrete surfaces on external faces of walls, in two coats (15 mm thick backing coat and 5 mm thick finishing coat) mixed with approved waterproofing compound, finished fair and even without using extra cement, complete all as specified and directed. |
| 15 | Material and labour for preparation of new plastered surfaces of walls, pillars and cornices and applying two coats of oil bound distemper over a coat of primer, including preparation of surfaces, complete all as specified and directed. |
| 16 | Material and labour for preparation of new plastered surfaces of ceilings and applying three coats of white wash on ceilings, complete all as specified and directed. |
| 17 | Material and labour for preparing newly plastered or unplastered surfaces and applying two coats of acrylic based exterior paint over a coat of primer, complete all as specified and directed. |
| 18 | Complete removal of existing treatment and preparation of surfaces of plastered or unplastered walls, including priming plastered and other surfaces with a coat of primer, applying a coat of wall care putty and two coats of oil emulsion distemper (white or tinted) on walls, complete all as specified and directed. |
| 19 | Material and labour for preparation of old decorated surfaces of walls, including washing and applying one coat of acrylic emulsion paint, exterior grade (100% acrylic), including necessary scaffolding, safety nets etc., complete all as directed by the Engineer-in-Charge. |
| 20 | Material and labour for preparation of old painted wooden surfaces of any description not otherwise described, over 10 cm width or girth, and applying one coat of synthetic enamel paint, complete all as specified and directed. |
| 21 | Material and labour for preparation of old previously treated steel or steel based surfaces of any description not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint (of approved shade) complete all as specified and directed. |
| 22 | Dismantling floor, hearth, or wall tiling incl cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises. all as specified. |
| 23 | Material and labour for non-skid coloured ceramic tiles 300 × 300 × 7 to 8 mm thick (square or rectangular), area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, laid in floors etc., set and jointed in epoxy mortar and pointed in white or coloured cement to match, including 20 mm thick screed bed in cement mortar (CM) 1:6, complete all as specified and directed. |
| 24 | Material and labour for non-skid coloured ceramic tiles 7 to 8 mm thick (square or rectangular), area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, laid in floors etc., set and jointed in neat cement slurry and pointed in coloured cement to match, including 20 mm thick bedding layer in cement mortar (CM) 1:4 for laying floor finishes, complete all as specified and directed. |
| 25 | Material and labour for rendering 10 mm thick in cement mortar (CM) 1:4 on backing coat of wall tiles etc., complete all as specified and directed. |
| 26 | Material and labour for coloured glazed ceramic tiles 300 × 200 × 7 to 8 mm thick on vertical surfaces, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match, complete all as specified and directed. |
| 27 | Material and labour for glazed ceramic tiles 300 × 450 × 7 to 8 mm thick on vertical surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specified and directed by the Engineer-in-Charge. |
| 28 | Dismantling of stone slabs, bedded and pointed in any mortar of any description or thickness in floors, aprons, etc., complete all as specified and directed. |
| 29 | Material and labour for granite stone (of any type) 18 mm thick, machine cut, laid over 15 mm thick cement screed bed in cement mortar (CM) 1:6, bedded and jointed with grey cement slurry and pointed with white cement mixed with pigment to match the shade of granite, including grinding and polishing, complete all as specified and directed by the Engineer-in-Charge. |
| 30 | Material and labour for machine cut mirror polished Kota stone slab flooring 20 to 25 mm thick, laid over 15 mm thick cement screed bed in cement mortar (CM) 1:6, bedded and jointed with grey cement slurry and pointed with cement mixed with pigment to match the shade of the slab, including rubbing and polishing (mirror finish), complete all as specified and directed by the Engineer-in-Charge. |
| 31 | Material and labour for mirror polishing of Kota or marble stone, fixed in any position and of any description, complete all as specified and directed. |
| 32 | Material and labour for 75 mm thick plain cement concrete (PCC) 1:4:8, type D2, using 40 mm graded stone aggregate, laid as sub-base, complete all as specified and directed. |
| 33 | Material and labour for 20 mm thick screed bed or bedding layer for laying floor finishes in cement mortar (CM) 1:6, complete all as specified and directed. |
| 34 | Material and labour for pre-polished coloured chequered cement concrete floor tiles 300 × 300 × 25 mm thick, machine pressed, laid in floors, set, jointed and pointed in neat cement slurry mixed with pigment to match the colour of tiles, complete all as specified and directed. |
| 35 | Demoliton of cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) all as specified and as directed by Engineer-in-Charge |
| 36 | M & L for Providing PCC 1:3:6 type C-2 using 40mm graded crushed stone aggregate as in foundation complete all as specified and directed. |
| 37 | Material & labour for machine pressed precast concrete inter locking paver block any shape and size with grey cement and pigment conforming to IS-15658-2006 of 60mm thickness M-35 Grade, glossy finished of approved colour laid over and including 25 mm thick fine sand cushion to a line and slope etc and joined complete including spreading screened river sand over surface for filling the joints and gently rolled with vibrator complete all as specified . |
| 38 | Taking down rolling shutters and refixing the same in its original position after cleaning all parts, straightening guide rails, replacing damaged strips, bottom rail and helical springs as required, including greasing, oiling and servicing for smooth functioning of all components, complete all as specified and directed. |
| 39 | Supply and fixing ball bearings for rolling shutters, complete all as specified and directed. |
| 40 | Dismantling of asbestos cement or galvalume sheets (corrugated, semi-corrugated, etc.) from roof coverings, complete all as specified and directed. |
| 41 | S&F pre-painted hot- dip aluminium-zinc alloy metallic coated corrugated steel sheet, any pattern corresponding to IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ150, 0.5 mm thick, of an approved colour and having yield strength of 550 MPa as in roof covering fixed with self tapping screws as specified including necessary scaffolding and safety measures at any floor for height of building exceeding 10 metres but not exceeding 20 metres complete all as specified and as directed. |
| 42 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. |
| 43 | M&L and fabrication of mild steel work as in posts,purlins,crane gantires, rafter ,rails,wind tie nut & bolt etc and fasteningsetc and heavy brackets framing (MS tube, beam,tee,angle,channels,flat section etc and other sections) including distance pieces,cleats etc complete all as specified and directed . |
| 44 | S&F framed work as in doors or gates ,chequered or plane plates, angles ,grills, or other securing with gusset plates rails braces,framed brackets etc. complete drilled to be prepared for hanging or sliding with and incl, either hooks and hinges or steel hanging door fitnes (Exclusive of steel, sheeting or other covering running rails and guides) and hanging also fastening and fixing complete. |
| 45 | Dismantling posts or struts (wood, steel or R.C.C.) embedded in concrete of any section, including taking out embedded portion and making good disturbed ground as per existing complete all as specified and directed . |
| 46 | Dismantling fencing wire mesh, any type all as specified and directed. |
| 47 | Excavation in post holes in soft or loose soil (or similar holes), each not exceeding 0.50 cubic metre, including getting out, returning, filling in and ramming earth or broken rubble and removing surplus soil, complete all as specified and directed |
| 48 | Material & Labour for PCC 1:3:6 type C-2 (40 mm graded crushed stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed by the Engr-in- charge. |
| 49 | Material and labour for applying two coats of synthetic enamel paint over a coat of red oxide primer on new steel surfaces, including preparation of surfaces of any description over 10 cm width or girth not otherwise described, complete all as specified and directed. |
| 50 | Supply only hot-dipped galvanised PVC coated mild steel chain link fencing, mesh size 100 mm × 100 mm, made of 4.0 mm diameter GI wire, including line wires, or any other approved mesh of any size and diameter of GI wire, complete all as specified and directed. |
| 51 | Supply and fixing 10 mm diameter mild steel round bars as line wires in chain link fencing, painted with two coats of synthetic enamel paint over a coat of red oxide primer before fixing in position, complete all as specified and directed. |
| 52 | Taking down chowkats or frame with shutter ( without taking off shutter from frame) , n exc 1.5 sqm each complete all as specified. |
| 53 | Taking down chowkats or frame with shutter ( without taking off shutter from frame) exc 1.5 sqm but n exc 4 Sqm each complete all as specified. |
| 54 | S & F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 2omm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of fplain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles. & rails with suitable PVC sheet beading, and joined together with sovent cement, suppling & fixing in the frame at site as per specification & direction. |
| 55 | S & F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, fixing in opening as per specification & direction. |
| 56 | Material and labour for machine cut mirror polished Kota stone (greenish colour, pre-mirror polished) slab, in one piece as in double step window cill of aluminium sliding windows, 18 to 20 mm thick, laid over 20 mm thick screed bed in cement mortar (CM) 1:3, complete all as specified and directed. |
| 57 | Material and labour for machine cut Kota stone (greenish colour, pre-mirror polished) slab, in one piece as in lintel and jambs of aluminium sliding windows, 18 to 20 mm thick, laid over 15 mm thick rendering in cement mortar (CM) 1:3, complete all as specified and directed. |
| 58 | S & F powder coated anodised aluminium frame/track or shutters for windows, ventilators etc. with one or more rebates including joining cleat for fixing etc.fixed or sliding type/louvered window or ventilator without sash bar, aluminium including necessary joining cleats, glazing clips, rubber packing, anodised alumnium snap beading, screws locking arrangements etc. complete all as specified and directed by Engr-in-Charge. Note: Minimum 25 micron anodisation for all aluminium sections) |
| 59 | Supply and fixing 4 mm thick plain sheet glass of ordinary quality, glazing with aluminium and neoprene beads, in squares not exceeding 0.5 sqm in each pane, complete all as specified and directed. |
| 60 | Supply and fixing 4 mm thick frosted sheet glass of ordinary quality, glazing with aluminium and neoprene beads, in squares not exceeding 0.5 sqm in each pane, complete all as specified and directed. |
| 61 | S&F factory made shutter 35 mm thick second class hard wood glazed and skelton shutters open rebated and prepared to receive glass, gauze etc edges of framing, plain chamfered or rounded fitted with cut and mitred beads fo securing gauge etc suzes of members of shutters as specified in SSR part I section 8 clause 8.24 (a) complete all as specified and directed |
| 62 | S&F 35 mm thick factory made Flush shutters , solid core constrution with block board core and plywood face panels, commercial type on both side complete all as specified and directed |
| 63 | Supply and fixing 100 mm long extruded aluminium handles, fabricated type, anodised, complete all as specified and directed. |
| 64 | Supply and fixing 100 mm long aluminium anodised barrel tower bolts of extruded section, complete all as specified and directed. |
| 65 | Supply and fixing 75 mm stainless steel medium weight butt hinges, complete all as specified and directed. |
| 66 | Supply and fixing 150 mm long extruded aluminium handles, fabricated type, anodised, complete all as specified and directed. |
| 67 | Supply and fixing 150 mm long aluminium anodised barrel tower bolts of extruded section, complete all as specified and directed. |
| 68 | Supply and fixing 300 mm long aluminium alloy anodised sliding door bolt with hasp and staple (bolt type) including fixing bolts and sliding bolts of extruded section or cast aluminium alloy, complete all as specified and directed. |
| 69 | Supply and fixing floor door stopper 140 mm overall length, aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, complete all as specified and directed by the Engineer-in-Charge. |
| 70 | Supply and fixing 100 mm stainless steel medium weight butt hinges, complete all as specified and directed. |
| 71 | Material and labour for applying two coats of synthetic enamel paint over a coat of pink primer on new wooden surfaces, of any description over 10 cm width or girth not otherwise described, including preparation of surfaces, complete all as specified and directed. |
| 72 | Supply and fixing in repairs PVC valveless, syphonic action type flushing cistern, low level, white, 10 litre capacity, with inlet, ball valve, float and handle including brackets, complete all as specified and directed. |
| 73 | Supply and fixing PVC connection 15 mm size with PTMT nuts, 450 mm long, in repairs, complete all as specified and directed. |
| 74 | Supply and fixing in repairs aluminium wire cloth, 0.45 mm nominal diameter of wire and average aperture width 1.40 mm, cut to required size and fixed to door and window shutters (wooden or aluminium) with wooden beading (any size) or aluminium wire staples, including removing old beading, complete all as specified and directed. |
| 75 | Material and labour for removing vegetation growth or shrubs by injecting Glyphosate 41% SL chemical, 20 ml or till refusal, by making cuts/injections in the stem of plants at 30 mm c/c and spraying with solution (25 ml Glyphosate 41% diluted with one litre of water) and removing plants/vegetation completely dead, including necessary scaffolding, jhulas etc., complete all as per manufacturer’s instructions |
| 76 | Chipping and carefully removing old broken concrete work by using low impact hammer/breaker without damaging the structure, including cleaning and disposal of debris outside the premises, complete all as directed by the Engineer-in-Charge.Note-Hard concrete shall not be removed by force. |
| 77 | Material and labour for applying rust remover alkaline in nature, having specific gravity 1.1 kg/litre, to existing or additional reinforcement bars, including wire brushing manually or by mechanical tools, cleaning the disturbed surface etc., complete all as specified and directed. |
| 78 | Material and labour for applying two coats of anti-rust protective coating in the form of acrylic polymer with minimum solid content of 40%, mixed with cement in 1 : 1.5 proportion (1 part polymer : 1.5 parts cement) on reinforcement bars after cleaning rust scales as per manufacturer’s instructions, complete all as specified and directed. |
| 79 | Supply and fixing 1.25 mm thick steel rolling shutters, without ball bearing, gear operated type with bevel gear box and crank handle, including top cover, anchoring rods, hasp and staple and one shop coat of primer, erected in position as indicated, including taking down existing parts if required, complete all as specified and directed by the Engineer-in-Charge. Please Enable Macros to View BoQ information |
