|
| 1 | Demolition of brick work built in cement mortar or cement lime mortar incl all quoins, arches pillars etc and removing unserviceable material exc 100 mtr complete all as specified and directed. |
| 2 | M&L for old size brick work with fly ash bricks straight or curved on plan exc 6 m mean radius build in CM 1:6 complete all as specified and directed. |
| 3 | Demolition of cement concrete (unreinforced) in ground floors and paving n exc 15 cm thickness (below or above ground level) including all type of tiling, marble chips , terrazo finish where ever existing etc all as specified and directed. |
| 4 | Dismantling of floor, walls tiles incl bedding but backing and rubbish off permises complete all as specified and directed. |
| 5 | M&L for 75 mm thick cement concrete M10 (Nominal Mix) with 40mm graded crushed aggregate finished even and fair laid to a slope of 1 in 12, laid in alternate bays, each bay not exceeding 3 m length with joint filled with bituminous mastic filling comprising a mixture of 1 part of heated Industrial bitumen 85/25 grade and two parts of heated sand as in plinth protection complete all as specified. |
| 6 | M&L 25 mm thick cement concrete (1:2:4), type B-0, using 12.50 mm graded aggregate as in floors including finishing the surface rough for laying finishes complete all as specified and directed. |
| 7 | M&L PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation filling, sub base and mass concrete complete all as specified and directed by Engineer-in-Charge. |
| 8 | M&L for Non -Skid Ceramic coloured tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18Sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement over and including 15mm thick screed bed in CM 1:6. complete all as specified and directed. |
| 9 | M&L Non Skid coloured ceramic tiles 7 to8 mm thick (Square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cemeent to match and including over screed bed or bedding layer of mortar 15 mm thick laying floor finished in CM 1:6 complete all as specified and directed. |
| 10 | M&L Coloured glazed ceramic tiles 350x250mmx7mm/450x350x7mm thick and jointed and in neat cement slurry and pointed in white or coloured cement on vertical surfaces in dado/Skirting over and including 15mm thick plastering in CM 1:4 on stone masonry surface complete all as specified and directed. |
| 11 | Taking down chowkats or frames with shutters (without taking off shutters from frames) area not exceeding 1.50 sqm each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost ot Govt), all as specified and directed by Engineer-in-Charge |
| 12 | All as per BOQ item No 11.00 here-in-above but area exc 1.5 Sqm but n exc 4 Sqm each complete all as specified and directed. |
| 13 | M&L for forming jambs in Cement mortar 1:4 to openings (to foregoing item) including cutting, toothing and properly bonding into old work. also facing, jointing and pointing to match existing work, complete all as specified and as directed by Engr-in-Charge. |
| 14 | Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators frame and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene asket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed chanically wherever required including cleat angle, luminium snap beading for glazing/ paneling, C.P. brass/ stainless teel screws, all complete as per architectural drawings and the irections of Engineer-in-Charge |
| 15 | S&F brass 4-levers mortice lock, vertical type , size 100mm complete all as spcified and as directed. |
| 16 | S&F Aluminium, anodised, barrel tower bolts 150mm long of extruded section complete all as specified and as directed. |
| 17 | S&F in repair aluminium (extruded section body) door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as spd and directed. |
| 18 | S&F aluminum alloy anodised sliding door bolts with hasp & staple & fixing clips of sheet cast extruded section & fixing bolts & sliding bolts of extruded section 300mm long. |
| 19 | S&F anodised extruded aluminium handle size 150 mm long fixed with screw complete all as specified and as directed. |
| 20 | M&L for 4 mm thick ACP (Aluminium composite panel) of any color fixed in aluminium with screw and tappered clip complete all as specified and directed. |
| 21 | Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 122 x 54 mm & sash 47 x 64 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately). Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 22 | S&F factory made UPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Glass shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted complete all as specified. |
| 23 | M&L sheet glass 5 mm thick ordinary quality and glazing with oil putty and pin in square n. exc 0.50 sqm in each pan complete all as specified and directed. |
| 24 | M&L for 4mm thick figured glass, pin head type and glazing with oil putty or with brass screws in square n.exc 0.50 sqm in each pan for bathrooms/toilets ventilators complete all as specified and directed. |
| 25 | S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned stacks or galvanised wire staples, complete all as specified and as directed. |
| 26 | M&L for framed work such as grills etc with ends of bars shouldered nd or riveed or forged into spike, framed guard bars and similar work conforming to Fe 290 Gde-E-165 complete all as specified and directed. |
| 27 | M&L for 18 to 20mm thick green marble (table rubbed and polished) in steps, jambs, pillars, window cills,bathroom corners cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with green marble shade complete all as spd and directed. |
| 28 | S&F Solid PVC door frame of size 50mm x 95mm made out of 5mm wood grain printed PVC sheet reinforced with M.S. tube, in opening as per specification & drawing complete all as specified and as directed. |
| 29 | S&F Factory made solid moulded PVC door shutter 28 to 30mm thick (style) with 2,4 or 6 raised panel design with 2 mm thick moulded PVC sheet on the front face & 2 mm thick plain colour PVC sheet on back face with particle face supply & fixing on frame, as per specification & drawing complete all as specified and as directed. |
| 30 | S&F stainless steel Butt hinges 100mm size, medium weight, complete all as specified and as directed. |
| 31 | S&F 150mm long aluminum anodised barrel tower bolts of extruded section complete all as specified and directed. |
| 32 | S&F Aluminium handles, cast type, anodized 150 mm size comp ISI Marked & as specified and directed. |
| 33 | S&F aluminum alloy anodised sliding door bolts with hasp & staple & fixing clips of sheet cast extruded section & fixing bolts & sliding bolts of extruded section 300mm long complete all as specified and directed. |
| 34 | S & F of 150 mm size (Overall length of cover plate) floor door stopper of aluminium body and tongue, anodised, with hard drawn steel spring complete all as specified and directed. |
| 35 | Demoition of RCC/brick work water tanks on top of slab & removing the debris from site complete all as specified and directed by Engr-in-Charge |
| 36 | S & F rotational moulded polyethylene ISI marked (vertical cylindrical with close top) as per IS 12701: 1996 of 1000 litres capacity hoisted and fixed in position with and including Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for 20/25mm bore dia iron pipe, provision of 20 mm /25 mm dia medium grade GI pipe for connecting inlet, outlet, over flow and washout pipes complete all as specified and as directed. |
| 37 | Taking up or down steel tubing and connections, including cleaning for re-fixing or removal to store of 15 mm dia complete all as specified and directed. |
| 38 | Taking up or down steel tubing and connections, including cleaning for re-fixing or removal to store of 20 mm dia complete all as specified and directed. |
| 39 | S&F 20 mm outer dia medium grade CPVC, SDR 11 & plain CPVC SDR 11 with all fittings (brass inside the fittings) and fixed complete to walls and ceiling or laid in floors complete all as specified and directed. |
| 40 | S&F 25 mm outer dia medium grade CPVC, SDR 11 & plain CPVC SDR 11 with all fittings (brass inside the fittings) and fixed complete to walls and ceiling or laid in floors complete all as specified and directed. |
| 41 | Cutting chases in brick wall, etc for concealed water tubing ,etc & making good in CM 1:3 , cutting not exc 10 cm girth complete all as specified and directed. |
| 42 | S&F in repairs 15 mm bore concealed type stop valves, cast copper alloy, chromium plated with long shank and cup (concealed type), high pressure with capstan head handle, screwed both ends for iron pipe or for unions of 15 mm dia complete all as specified and directed. |
| 43 | S&F in repairs angle cock 15 mm bore fancy type chromium plated, with capstan head, high pressure, screwed down, screwed for iron pipe or for brass ferrule fixed to iron pipe. |
| 44 | S&F in repairs two way angle cock 15 mm bore fancy type chromium plated, screwed down, screwed for iron pipe or for brass ferrule fixed to iron pipe complete all as specified and directed. |
| 45 | S&F in repairs Bib taps, cast copper alloy, chromium plated , screwed down, high pressure, screwed for iron pipe or for brass ferrule of 15mm dia complete all as specified and directed. |
| 46 | Supply and fixed in repair shower rose brass chromium plated with swivel joints, 125 mm size, fixing to steel pipe or union complete all as specified and directed. |
| 47 | S&F in repairs PVC connection 15mm dia size and 450 mm long with 2 Nos brass check nuts its washers complete all as specified and as directed. Make - Prayag/Jaquar/Parryware. |
| 48 | S & F in repairs vitreous china squatting pan, 'Orissa\\" pattern, size 580 mm X 440 mm white with ‘P’ or ‘S” trap, front or back inlet and integral foot rests, any pattern and including fixing , connector to flush pipe, lime concrete bedding and making connections to flush pipe, connector to branch pipe and anti syphonage pipes etc. including sealing the joints and making leak proof using sealant complete all as specified and as directed by Engineer-in-Charge. |
| 49 | S & F in repairs vitreous china wash down water closet (pedestal pattern), white including thermoplastic seats and covers of grade 2 type, flat with hinging device of bronze or brass with nickel chromium plating, fixing bolt, connector to flush pipe and making connections to flush pipe, connector to branch soil pipe and anti syphonage pipes etc. including sealing the joints and making leak proof using sealant complete all as specified and as directed by Engineer-in-Charge. |
| 50 | S&F 10 Ltr capacity PVC valveless shyphonic action type low level flushing cistern white with inlet, ball valve, float valve and handle incl bracket and flush pipe fixed to wall complete, incl taking down old cistern of any description. |
| 51 | S&F in repair brass chromium plated health faucet for EWC with 15 mm dia PVC pipe 1.00 m long including nut/washer complete all as specified and directed. |
| 52 | S&F in repairs Gun metal, globe or gate valve with iron wheel head, 20 mm bore, screwed both ends for iron pipe all as specifed. |
| 53 | S&F in repairs Bras CP towel rail 20mm dia `D' type 60 cm long between flanges complete all as specified and directed. |
| 54 | S&F in replacement of stainless steel soap dish, of standard size and shape complete all as directed. Make : Parryware/Hindware/Jaquar |
| 55 | S&F in repair 5 mm thick looking mirror selected quality glass exc 0.50 sqm each and fixed to wall with brass screws, cups and washers including polished, rounded off edges of glassand drilling hole in glass complete as specified and directed. |
| 56 | S & F in repair shelf of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats complete all as specified and directed. |
| 57 | S&F in repair PTMT grating 100 mm size (ISI Marked) complete all as specified and directed. |
| 58 | Taking down cement plaster from brick/concrete surfaces including raking out joints, hacking for key and scrubbing down with water etc all as specified and directed. |
| 59 | M&L for 5 mm thick cement plaster in cement mortar (1:3) as on ceiling, finished even & smooth without using extra cement complete all as specified and directed. |
| 60 | M&L for 15 mm thick cement plaster in cement mortar (1:6) as on walls, finished fair and even complete all as specified and directed. |
| 61 | Material & Labour for preparation of new surfaces of plastered walls and applying Two coats of Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. over and including a coat of primer over plastered surfaces of walls complete all as specified. |
| 62 | M&L for preparing of new steel & iron surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enameled paint over a coat of Red oxide zinc chrome primer zinc chrome complete all as specified and as directed. |
| 63 | Preparing Old Distempered Surfaces of WALLS by Washing, Rubbing down and Stopping of Distem-pered and Painted Surfaces and applying ONE COAT of OIL BOUND WASHABLE DISTEMPER, complete all as specified and as directed. |
| 64 | M&L for preparing old decorated plastered or unplasterd surfaces of ceiling including cornices, pilasters and other wall features etc by brooming down or steel wire brushing and sand paper, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc and removing extra wall papdi ,peel off wall papdi by sand paper and making good with external wall care putty as per existing thickness and applying two coats of white wash on ceiling complete all as specified and as directed. |
| 65 | Taking down CI/PVC/AC pipes (including all fittings), with spigot and socket ends and lead joints including burning out joints of 100/75 mm dia pipe complete all as specified and directed. |
| 66 | S&F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls with brackets etc of 110 mm dia complete all as specified and directed. |
| 67 | S&F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls with brackets etc of 75 mm dia complete all as specified and directed. |
| 68 | S&F PVC (SWR) bends/ shoes any radius of 110 mm dia complete all as specified and directed. |
| 69 | S&F PVC (SWR) bends any radius of 75 mm dia complete all as specified and directed. |
| 70 | S&F PVC (SWR) bends any radius provided with access door of 110 mm dia complete all as specified and directed. |
| 71 | S&F PVC (SWR) bends any radius provided with access door of 75 mm dia complete all as specified and directed. |
| 72 | S&F PVC (SWR) branch pieces, single (equal or un equal) , ordinary or inverted (spigot or socket type) or with parralled branches of 110 mm dia with access door complete all as specified and directed. |
| 73 | S&F PVC (SWR) branch pieces, single (equal or un equal) , ordinary or inverted (spigot or socket type) or with parralled branches of 75 mm dia with access door complete all as specified and directed. |
| 74 | S&F PVC (SWR) vent cowl of 110 mm dia complete all as specified and directed. |
| 75 | Cutting holes into or through full brick walls built in cement mortar of suitable size and shape for fixing exhaust fan and including making good to the original surfaces of any description disturbed, in cement mortar 1:3 or cement concrete 1:2:4 type B-l as required and painting or decorating as per existing complete all as specified and directed. Please Enable Macros to View BoQ information |
