|
| 1 | Repair/Replacement of 7.5 HP Mody make submersible pump of following parts (old material to be retained by the firm):- Rewinding kit including enamel copper wire, Nomex paper, sheet paper, varnish, lead wire, transformer fiber glass sleeves, etc. as required. |
| 2 | Replacement of set of 'O' ring |
| 3 | Replacement of Mechanical seal upper. |
| 4 | Replacement of Mechanical seal lower. |
| 5 | Replacement of ball bearing upper. |
| 6 | Replacement of ball bearing lower. |
| 7 | Replacement of oil. |
| 8 | Replacement of cable size 7C x 4 sq mm + 2C x 1 sqmm |
| 9 | Labour charge for oil filling & servicing of seal module. |
| 10 | Labour charge for disantling/ assembling/ testing/ painting etc. |
| 11 | Reparing of sewage submersible pump set 15HP (Mody make): Supply of spares for 15 HP sewage sumersible pump a) 'O' ring |
| 12 | Mechanical seal upper. |
| 13 | Mechanical seal lower. |
| 14 | Ball bearing upper. |
| 15 | Ball bearing lower. |
| 16 | Hardware |
| 17 | Rewinding kit |
| 18 | Labour charge for rewinding |
| 19 | Labour charge for repairing & balancing of rotor |
| 20 | Labour charge for dismantling/assembling/testing/painting etc. |
| 21 | Labour charge for fixing upper & lower bearing |
| 22 | Repair/Replacement of 20.0 HP Aqua make submersible pumps worn out of following parts (old material to be retained by the firm):- Rewinding kit including used material insulation Rewinding/ Copper Millan Make H Class, Nomex paper/glass resins/glass tape/resin hardener) fiber class sleeve/varnish/thinner/Epoxy all Insulation F Class. |
| 23 | Mechanical Seal set |
| 24 | Bearring Set |
| 25 | O Ring Set |
| 26 | Oil Charges |
| 27 | Cable Gland |
| 28 | Dual PVC Sheathed Rpound Type Copper Flexible Cable withGland Sealing (1Rx10Cx2.5 sqmm)-10 Mtr |
| 29 | Hardware including nut-bolts, Varsal/ washer |
| 30 | Overhauling charges (Dismantling of pump assembly dynamically balancing of Rotor & Impeller, Complete assembly of Pump Motor set, Hydraulic Testing etc.) |
| 31 | Supply, Installation, testing and commissioning of cubical type control panel board for single phase & Three Phase submersible pumping set of following rating complete with contactor, relay , MCB ,condenser ,voltmeter, ammeter and indication lamp etc including connections etc as reqd a)7.5 HP (Three Phase) |
| 32 | S/I/T/C of cubical type control panel board for three phase star delta starter, three position selection with auto switch for Mono submersible pumping set of following rating complete with single phasing preventer in auto, contactor (25Amp), O/L relay TP, MCB, Voltmeter, ammeter, VSS and indication lamp etc. including lamp etc. including connection etc. as required. (b) 15 H.P. rating Submersible Pump Set Over Load relay (range30-32 Amp) & Contactor (range 32 Amp) |
| 33 | P&F following sizes of PVC insulated & PVC sheathed copper conductor 3 core submersible cable confirming to IS.694/1990 etc. as reqd. a) 3x6 sqmm |
| 34 | P&F following sizes of PVC insulated & PVC sheathed copper conductor 3 core submersible cable confirming to IS.694/1990 etc. as reqd. a) 3x10 sqmm |
| 35 | Servicing of DG SET Kirloskar Make Model No. KG 125 WS-3 - 125 KVA at Daryapur Pumping Station from s.no. 73 to 93 providing OF Primary Element (3H.132.01.0.00) for KG 125 WS-3 125 KVA |
| 36 | Providing of Secondary Element (3H.132.02.0.00) for KG 125 WS-3 125KVA |
| 37 | Providing of Spin on Lube Oil Filter (06.436.01.0.00) for KG 125 WS-3 125 KVA |
| 38 | Providing of 16\\" Air Cleaner Element (F6.729.03.0.00) for KG 125 WS-3 125 KVA |
| 39 | Providing of Safety Air Element (F6.729.04.0.00) for KG 125 WS-3 125 KVA |
| 40 | Providing of Assembly Leak Off Pipe (F6.304.01.0.00) for KG 125 WS-3 125KVA |
| 41 | Providing of Hose For Thermostat to Water Tank (F6.255.06.0.00) for KG 125 WS-3 125 KVA |
| 42 | Providing of Hose (F6.377.08.0.00) for KG 125 WS-3 125 KVA |
| 43 | Providing of Hose (F6.150.03.0.00) for KG 125 WS-3 125 KVA |
| 44 | Providing of Hose Clip (30.650.02.0.00) for KG 125 WS-3 125 KVA |
| 45 | Providing of Hose T-Bolt Clamp (4H.1412.24.0.00) for KG 125 WS-3 125 KVA |
| 46 | Providing of Fuel Pipe Inlet: M14 x M14 Banjo Both side 900L (4H.896.09.0.00) for KG 125 WS-3 125 KVA |
| 47 | Providing of Fuel Pipe Inlet: M14 x 1.5 Banjo Both side 650mm (06.718.11.0.00) for KG 125 WS-3 125 KVA |
| 48 | Providing of LFL Sensor (Low Fuel Level) 16Smm Height (6H.192.14.0.00) for KG 125 WS-3 125 KVA |
| 49 | Providing of Battery Terminal (LPU.ELE.41.0.00) for KG 125 WS-3 125 KVA |
| 50 | Providing of Lugs Battery Cable (LPU.ELE.08.0.00) for KG 125 WS-3 125 KVA |
| 51 | Providing of Conversion Kit From KG 934 to KG 645 for KG 125 WS-3 125 KVA |
| 52 | Providing of Kirloskar care Premium Oil 20 Itr can (82.060.10.0.20) for KG 125 WS-3 125 KVA |
| 53 | Providing of Kirloskar care Premium Oil 5 ltr can (82.060.10.0.05) for KG 125 WS-3 125 KVA |
| 54 | Providing of Kirloskar care Coolant Premix 10 Itr can (82.020.35.1.10) for KG 125 WS-3 125 KVA |
| 55 | Post Warranty Labour Charges (99.0PW.01.0.00) for DG set servicing for KG 125 WS-3 125 KVA |
| 56 | 125 KVA DG Set Repair & Overhauling Work :-Repair and Overhauling 125 KVA DG Set by consuming /utilizing following material/ spare parts and service charges towards including Repair calibration and testing of injectors, Repair calibration and testing of fuel injection pump, Repair calibration and testing of cylinder head, Engine top overhauling repair and testing in workshop, De-scaling of Rediator (Repair calibration and testing st site) including loading unloading by skilled laboure and transportation charges of from site to workshop and back from workshop to site. |
| 57 | Oil Filter Spinon 1 LTR |
| 58 | Fuel Filter 1 LTR |
| 59 | COEL CARE Genuine Coolent Premix 26 Ltr |
| 60 | COEL CARE Super Genuine Oil 5 Ltr |
| 61 | COEL CARE Super Genuine Oil 20 Ltr |
| 62 | HOSE: Pipe to Water Pump 45x45x80 |
| 63 | HOSE: T-Bolt Clamp |
| 64 | HOSE: Water Pipe |
| 65 | Fuel Filling Hose: 36-125 KVA |
| 66 | Hose Clip |
| 67 | Hose Radiator to Waterpump45x45 |
| 68 | Set of Joints 6R1080TA |
| 69 | Piston Assembly |
| 70 | Clinder Liner with Joint Ring |
| 71 | Turbo Charger |
| 72 | Air Fillter Kit A-4R1040BS3 INDL |
| 73 | Valve Stem Seal |
| 74 | Valve Bridge |
| 75 | Valve seat Insert: Exhaust |
| 76 | Valve seat Insert: Inlet |
| 77 | Valve Guide |
| 78 | Service ChargesTowards the repair calibration and testing of injectors, |
| 79 | Service ChargesTowards the repair calibration and testing of fuel injection pump |
| 80 | Service ChargesTowards the repair calibration and testing of cylinder head |
| 81 | Service ChargesToward the repaire Engine top overhauling repair and testing at workshop |
| 82 | Service ChargesToward the De-scaling of Rediator (Repair calibration and testing st site) Please Enable Macros to View BoQ information |
