|
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 min width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil. DSR 2023/2.8.1 (Rate 260.30) |
| 2 | Providing and laying OF 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources DSR 4.1.8/2023 |
| 3 | 12 mm cement plaster of mix :1:4 (1 cement: 4 coarse sand) DSR 2023/13.4.1 (RATE-357.35) |
| 4 | Brick work with class 150 class bricks of designation 15 in foundation and plinth in:Cement mortar 1:4 (1 cement : 4 coarse sand) (AS per DAR) OR DSR S.I.No. 6.1.1/2023 (Rate 7846.30) |
| 5 | Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. DSR/2023 S I No 10.1 (Rate 117.35) |
| 6 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. S I No 10.2 DSR/2023(Rate 133.70) |
| 7 | Providing and fixing of danpolan 16MM thick Multicell Skylight Systom Along with standard accessories UPD, FPD, AD tap Expention Fatsener U Connector.end Tape, Screws, Breathable tap, All complete in Diredction Of engneer Incharge Make Danpal/poygal.(Marketed ) (PSR -C.B 2875) |
| 8 | Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :25 mm thick DSR2023/11.26.1(RATE-1948.25) |
| 9 | Marble stone flooring with 18 mm thick marble stone, as per sampleof marble approved by Engineer-in-charge, over 20 mm (average) thickbase of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with :DSR-11.23.2/2023 Raj Nagar plain (Rate 2346.80) |
| 10 | Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws DSR 2023/9.21.2)(Rate 2172.10) |
| 11 | Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size), including necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 DSR2023/18.33.1(RAET-10862.40) |
| 12 | P/F of Stainless steel SS grade 304, curtain rod 25 mm dia 1.20 mm thickDSR2023/0455(RATE-187.00) |
| 13 | P/F of Stainless steel SS grade 304, Brackets For support of curtain rod 25 mm dia DSR2023/0457(RATE-60.0) |
| 14 | Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete. (Copper oxidised as per IS 1378) 300x16 mm DSR 2023/9.62 (RATE-83.90) |
| 15 | Providing and fixing ISI marked oxidised M.S. tower bolt black finish,(barrel type) with necessary screws etc. complete. (Copper oxidised as per IS 1378) 250x10 mm DSR2023/9.63 (RATE-83.90) |
| 16 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new work DSR 2023/13.61 (Rate 155.90) |
| 17 | providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc complete SorSNO-9.66.1 125 mm |
| 18 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels .Granite stone slab of colour black, Cherry/Ruby red Area of slab upto 0.50 sqm. DSR 8.2.2.1/2023(RATE-5413.50) |
| 19 | Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete. Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sides DSR/2023 S I No. 10.29.2 (Rate 1133.55) |
| 20 | Providing and fixing 25 mm thick shutters for cupboards: Panelling or Panelled & Glazed shutters : Second class teak wood including ISI marked nickel plated bright finished MS Piano hinges with necessary screws DSR/2023/9.16.1.2 (Rate 4542.90) |
| 21 | Providing and fixing cupboard shutter with 19mm thick one side decorative and other side balancing lamination factory pressed BWP grade marine ply as per IS 710 of approved brand including 2mm thick PVC edge banding tape with hot glue by edge bending machine etc. with auto closing spring loaded hinges (hydraulic type) etc. complete as per direction of Engineer-in-charge.(Payment of providing and fixing auto closing hinges shall be paid separately) DSR No 9.168/2023(RATE-2829.25) |
| 22 | Providing and fixing 19mm thick both side balancing lamination factory pressed BWP grade marine ply as per IS 710 of approved brand boxes, shelves, racks, almirah, cupboard and drawer etc. including necessary nails,screws etc. complete as per direction of Engineer-in charg DSR No 9.169/2023(RATE-2593.15) |
| 23 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I.wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, theperimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks) DSR 2023 12.45.1 (RATE-1355.80) |
| 24 | P/L Cornice With design with POP(Plaster of Paris) including Supply of all material, Labour and T&P etc all complete of the work (PSR) CB. No-2722/MDA/EE/22 |
| 25 | Cutting holes of required size in brick masonry wall for fixing of exhaust fanincluding providing and fixing 300 mm dia PVC pipe conforming BIS-12818 and making good the same etc. complete as per direction of Engineer-incharge DSR 2023 14.81(RATE-288.10) |
| 26 | Supply and Installation of Exhaust Fan, A standard 300–450 mm wall/ceiling-mounted exhaust fan with metal or plastic body, noiseless blades, protective grill, and 220–240V operation. Brands like Crompton, Usha, Bajaj, and Havells are common as per design / instructions of(MR) |
| 27 | supply and installations of daikin 2.00 ton 3 star fixed speed split AC model no. ftl 50 u cost (100% coppper ) om 2.5 air purifine filter all complete . ( P.S.R .NO. 2792/2023) |
| 28 | Supply & fixing of LED Strip Light all complete as per drawing and specification and direction of engineer incharge. Make-KliteHavells,Philips Equivalent (P.S.R) C.B NO.2706/MDA/2022 |
| 29 | Supply & Fixing of LED Strip Driver all complete as per drawing and specification and direction of engineer incharge. Make-Klite, Havells,Philips (P.S.R) C.B NO.2706/MDA/2022 |
| 30 | Supply & fixing of LED Linear light complete as per design, drawings, specification & as approved by E/I. (P.S.R) C.B NO.2706/MDA/2022 |
| 31 | Supply and Fixing of recess mounting round 12 Watt COB LED Spot Light having Powder coated die cast aluminium housing with heat sink, diffuser/ Reflector and driver set complete in all respect. (P.S.R) C.B NO.2706/MDA/2022 |
| 32 | Providing and fixing of false ceiling led light 7 watt (MR) as per direction of engineer havells make other ancher make . |
| 33 | Providing and Installing Zebra Blinds as per the directions of engineer in charge. (P.S.R) C.B NO.2706/MDA/2022 |
| 34 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily Glazed Vitrified tiles Matt/Antiskid finish of size Size of Tile 600 x 600 mm DSR2023/11.41A.3.1(RATE-1464.85) |
| 35 | Supplying and fixing new wooden fillets wherever necessary:2nd class teak wood fillets DSR2023/14.8.1(RATE-77.70) Please Enable Macros to View BoQ information |
