|
| 1 | (ii) The contractor or his representative shall collect daily list of complaints from MES complaint cell or from concern JE and shall attend all the complaints in the same day irrespective of number of complaints received. Contractor shall employ sufficient tradesmen accordingly as per requirement. However minimum one plumber and carpenter shall be made available throughout working hours to attend emergency complaints. The rates quoted by the contractor shall be deemed inclusive of cost against supervisor, all tradesmen / labours employed, conveyance required for collecting complaints and attending at site for all items of BOQ. (iii) Contractor shall employ skilled / experienced tradesmen and workers for execution of work. (iv) Contractor or his representative shall submit compliance report of complaints on the same day with receipt / job card duly signed by the users to concern JE. Contractor may use separate register for each category of complaints and obtain signature from users after repair / rectification of complaints received and submit the same during preparation of RARs to concern JE. (v) All critical complaints related to water supply and complaints which posses safety hazards to occupants have to be rectified within 24 hours after receipt of complaints. In case of complaints are not rectified on same day, the contractor shall submit in writing to Engineer-in-charge with valid reasons / justifications for delay and however the same shall be rectified with in 2 working days. Otherwise a recovery of Rs 500 per complaint shall recovered from the contractor. (vi) All unserviceable materials, debries, waste material scrap etc. obtained during repair work other than such of credit materials issued to the contractor shall be removed immediately from site and disposed off at dumping locations earmarked with in the INA premises at no additional cost to the Govt. The cost of labour, transportation etc. shall be deemed included in the rates quoted by the contractor against respective BOQ items and nothing extra shall be paid. |
| 2 | Material & labour for applying two coats of Smart care damp proof of Asian Paints by roller/brush over a coat of primer with smart care damp proof 33 % dilution of Asian paints including preparation of existing WALL surface by complete removal of existing treatment by means of chipping the surface to remove loose particles and mortar and clean the surface with wire brush and water wash etc including filling & coving with smart care repair mortar (wherever required), filling of crack filler with smart care crack filler of Asian Paints (wherever required) complete all as per manufacturer’s instructions, all as specified and as directed by Engr-in-Charge. (Make : Asian Paints Smart care Damp proof). |
| 3 | Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead all as specified and as directed. |
| 4 | Material & labour Glazed ceramic coloured tiles in patches 300x200x7mm thick in vertical surfaces of stone/brick wall, set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15mm thick backing coat plaster in CM 1:4 all as specified and as directed. |
| 5 | Material & labour Glazed ceramic coloured tiles 350x250x7mm /450x350x7mm thick in vertical surfaces of stone/brick wall, set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15mm thick backing coat plaster in CM 1:4 all as specified and as directed. |
| 6 | Material & labour coloured Non-skid ceramic tiles (square/rectangular) 7 to 8mm thick in floors, area of each tile exc.0.06 sqm but n.exc 0.11 sqm, set and jointed in neat cement slurry and pointed in white cement mixed with matching pigment over and including 15mm thick screed bed in CM 1:6 all as specified and as directed. |
| 7 | Material & labour machine cut granite stone slab 20mm thick of approved colour and shade as in floors, kitchen platform, steps and other similar situations over and including 15mm thick backing coat in CM 1:4 laid and jointed in grey cement slurry and pointed with white cement with admixture of pigment to match the shade of the slab including grinding and polishing all as specified and as directed. |
| 8 | Rounding to edges of stone slabs to one edge, such as in kitchen platform, steps and other similar situations all as specified and as directed. |
| 9 | Cutting of granite stone for fixing kitchen sink complete all as specified and as directed. |
| 10 | Demolition of Concrete in ground floors and pavings exc 15 cm thickness above ground level) all as specified and as directed. |
| 11 | Cement concrete in foundations, filling and mass concrete Type B2 1:2:4 (40 mm graded aggregate) in sunken floors all as specified and as directed. |
| 12 | APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non woven fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application in sunken slabs complete all as specified and as directed. |
| 13 | Supply & fix in repairs Matte finish stainless steel 1mm thick kitchen or laboratory sink with plugs,washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe ,overall size 495mm x 420mm bowl size 410mm x 160mm complete all as specified and as directed. |
| 14 | Taking down cement plaster of any description on brick wall, ceiling etc. including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed. |
| 15 | Rendering 15mm thick on fair faces of brick work or concrete surfaces - Cement plaster 1:6 to be finished even and smooth without using extra cement all as specified and as directed. |
| 16 | Dismantling of structural steel work including doors etc. including dismembering and stacking all as specified and as directed. |
| 17 | Supply & fix Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 all as specified and as directed. |
| 18 | Material & labour preparation of new steel surfaces of any description over 10 cm in width or girth and painting with two coats of Aluminium paint over a coat of aluminium red oxide primer complete all as specified and as directed. |
| 19 | Material & labour preparation of new steel surfaces of any description over 10 cm in width or girth and painting with two coats of synthetic enamel paint over a coat of red oxide primer all as specified and as directed. |
| 20 | Taking down chowkats or frames not exc. 1.5 Sqm each but without taking off shutters from the frames all as specified and as directed. |
| 21 | Taking down chowkats or frames exc. 1.5 Sqm but n.exc 4 Sqm each but without taking off shutters from the frames all as specified and as directed. |
| 22 | Supply & fix Pressed steel frames for doors of size 125x60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed |
| 23 | Material & labour for Cement concrete 1:3:6 type C0 using 12.5 graded aggregate as filling inside pressed steel frame chowkat all as specified and as directed. |
| 24 | Supply & fix powder coated aluminium frame for doors, windows, ventilators, partitions,kitchen cupboars frame etc with one or more rebates including joining cleat for fixing etc. complete all as specified (minimum thickness of powder coating not less than 50 micron) all as specified and as directed. |
| 25 | Supply & fix Powder coated aluminium door shutters, aluminium sectionof size 85 x 44.45 mm as frames incl necessary joining cleats glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges anodised aluminium snap beaking screws etc completeall as specified and as directed. |
| 26 | Supply & fixPowder coated aluminium window and ventilator shutters fixed or sliding type without sash bar, aluminium section weighing 0.55 kg/m incl necessary joining cleats rubber packing anodised aluminium snap beading screws etc completeall as specified and as directed. |
| 27 | Supply & fix Aluminium expanded metal mesh 0.45 mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminum staples or beading complete all as specified and as directed. |
| 28 | Supply & fix Aluminium composite panel 4 mm thick of approved colour and shade fixed with self tapping screws on aluminium frame work in suitable shape and size complete all as specified and as directed Note: Supply and fix aluminium frame work if required shall be measured and paid seperately |
| 29 | Taking down shutter of any description (wooden/Aluminim/steel ) exc. 1 Sqm and n. exc 2 Sqm each complete all as specified and as directed. |
| 30 | Taking down shutter of any description(wooden/Aluminium/steel ) exc 2 Sqm each complete all as specified and as directed. |
| 31 | Material & labour solid PVC door frame of wood grain pvc of sizes 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, as per specification and drawings all as specified and as directed. |
| 32 | Supply and fixing 24 mm thick factory made PVC door shutters to existing door frames made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and jointed at the corners by means of M.S. galvanized/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as specified by the manufacturer and as per directions of Engineer- in-charge. (For W.C. and bathroom door shutter) all as specified and as directed. |
| 33 | Material & labour second class soft wood, 30mm thick, flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, both face is covered with decorative face veneer with lipping/frame to match supplied and fitted to chowkats complete all as specified and as directed. |
| 34 | Supply only 100mm stainless steel butt hinges, IS :12817 marked cold rolled medium weight all as specified and as directed. |
| 35 | Supply only 150 mm aluminium handles cast type ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc all as specified and as directed. |
| 36 | Supply only 150 mm Aluminum barrel tower bolts of extruded section ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc all as specified and as directed. |
| 37 | Supply & fix in repairs 100 mm aluminium handles cast type ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc all as specified and as directed. |
| 38 | Supply & fix in repairs 125 mm Aluminum barrel tower bolts of extruded section ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc all as specified and as directed. |
| 39 | Supply only 200 mm aluminum alloy sliding door bolt with hasp, staple (bolt type) ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy all as specified and as directed. |
| 40 | Supply & fix in repairs 200 mm aluminum alloy sliding door bolt with hasp, staple (bolt type) ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy all as specified and as directed. |
| 41 | Supply & fix in repairs 300 mm aluminum alloy sliding door bolt with hasp, staple (bolt type) ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy all as specified and as directed. |
| 42 | Supply & fix in repairs floor door stopper 150 mm size aluminium alloy body and tongue double legged, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etcfixed to door.all as specified and as directed. |
| 43 | Supply & fix in repairs mild steel friction hinges suitable for window/ventilator shutters all as specified and as directed. |
| 44 | Supply & fix in repairs 75 mm bright finished brass handles, cast type, polished, ornamental type for drawers, etc. all as specified and as directed. |
| 45 | Supply & fix in repairs 150 mm bright finished brass handles, cast type, polished, ornamental type for cupboards all as specified and as directed. |
| 46 | Supply & fix in repairs aluminium powder coated Ebco handles for sliding windows complete fixed all as per manufacturers instruction all as specified and as directed. |
| 47 | Supply & fix in repairs 75 mm hasp and staple mild steel safety type and fixed with screws all as specified and as directed. |
| 48 | Supply & fix in repairs aluminium alloy wire cloth, 0.45 mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminum staples or beading complete all as specified and as directed. |
| 49 | Supply & fix in repairs rubber beading suitable size for safety purpose (snake guard) in bottom of door complete as specified and as directed. |
| 50 | Dismantling boarding, any description, fixed in any position with screws complete all as specified and as directed. |
| 51 | Supply & fix 18-20 mm thick extruded polymer profile form board made of ‘U’ Pvc polyester resin of any colour and pattern used as in kitchen cabinets/ wardrobes/ Shutters/drawers etc fixed with screws in required size and shape all as specified and as directed.Make : Greenply/Thomson multiwood/M/s RajashriPlastiwood indore, M/s Sintex Industries LtdNote : Necessary fittings will be measured and paid separately under relevant items |
| 52 | Supply & fix medium density fibre board exterior grade 18/19 mm thick as in cupboard, drawer repair & fixed with screws to timber frame work complete all as specified and as directed. |
| 53 | Material & labour preparation of new wooden surfaces of any description over 10 cm width or girth and painting with two coat of synthetic enamel paint over a coat of pink primer complete all as specified and as directed. |
| 54 | Material & labour for 1.00 mm thick glossy finish Acrylic laminate of surface finish, colour and pattern as approved, fixed with approved adhesive for fixing over polymer profile foam board (Multiwood) as per manufacturer's instructions complete all as specified and as directed. |
| 55 | Supply & fix 450 mm long stainless steel telescopic drawer channel double ball bearing complete fixed all as per manufacturers instructions all as specified and as directed. by Engr-in-Charge. (Make : Sleek by Asian paints) |
| 56 | Supply & fix stainless steel soft closing hydraullic hinges for shutter complete all as specified and as directed.(Make : Sleek by Asian paints) |
| 57 | Supply & fix 125 mm bright /matt finished stainless steel handles, cast type, polished for cupboard shutters etc. complete all as specified and as directed.(Make : Sleek by Asian paints) |
| 58 | Hacking out old broken glass (any thickness, size, quality or description) form metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified and as directed. |
| 59 | Supply & fix sheet glass 4mm thick, ordinary quality and glazing with oil putty in square exc 0.5 sqm in each pane all as specified and as directed. |
| 60 | Material & labour 4mm thick sheet figured glass pin headed quality exc 0.50 sqm in each pane and glazing with aluminium beading complete all as specified and as directed. |
| 61 | Taking down shutter of any description exc 1 Sqm but n exc 2 Sqm each and refixing the same after carrying out repair including easing and adjusting and also refixing builders hardware as required including renewal of unserviceable screws, etc. all as specified and as directed. |
| 62 | Repairs to wooden shutter of any description exc 1 Sqm but n exc 2 Sqm each including easing and adjusting and also refixing builders hardware as required including renewal of unserviceable screws, etc. all as specified and as directed. |
| 63 | Taking down existing aluminium glazed window shutters of any description for repairing and refixing in the same opening after carrying out repair works all as specified and as directed.Note :- New materials required for replacement of old items shall be measured and paid seperately vide relevant items. |
| 64 | Supply & fix in repairs looking mirror 600X450mm, selected quality glass mounted on 6mm thick PVC/AC building board/commercial plywood, PVC beading allround and fixed to wall complete all as specified and as directed. |
| 65 | Supply & fix in repairs Mortice lock brass body, 100mm, 4 levers vertical type all as specified and as directed. |
| 66 | Supply & fix in repair 20 mm bore curtain rods, anodised aluminium alloy, PVC coated with fixing brackets, stops, rollers etc all as specified and as directed. |
| 67 | Supply & fix in repairs aluminum (die cast) body door closer hydraulically regulated designation No. 2 universal type suitable for door shutters of 701 to 850mm in width and of weight between 36 to 60 Kg all as specified and as directed. |
| 68 | Supply & fix in repairs vitreous china, wash down water closet (EWC) white colour with PVC seat cover and lid, closed pattern with flat bottom and cover with mild steel (CP) or aluminium hinging device fixed with necessary bolts complete all as specified and as directed. |
| 69 | Supply & fix in repairs plastic water closet seat cover white colour closed pattern with flat bottom and cover and MSCP or aluminium hinging device all as specified and as directed. |
| 70 | Supply & fix in repairs vitreous China wash hand basin, white coloured, flat back 550x400mm including waste coupling CP, fixing brackets, cutting for and pinning in ends of brackets all as specified and as directed. |
| 71 | Supply and fix in repairs PVC valve less syphonic action type flushing cistern low level with inlet ball valve float and handle including brackets,manually controlled device (handle lever) conforming to IS:7231,10 ltrs capacity all as specified and as directed. |
| 72 | Supply & fix in repairs 15mm bore chromium plated bib taps (fancy type), long body cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed for iron pipesall as specified and as directed. |
| 73 | Supply & fix in repair 15mm bore chromium plated bib taps all as specified. Jaquar Cat No KUP35037PM all as specified and as directed. |
| 74 | Supply & fix in repair 15mm dia bore pillar taps, cast copper alloy, fancy type capstan heads, chromium plated, screwed down high pressure, with long screwed shanks and fly-nuts, screwed for iron pipe all as specified and as directed. |
| 75 | Supply & fix in repair 15mm dia bore pillar taps, chromium plated all as specified. Jaquar Cat No KUP35001PM all as specified and as directed. |
| 76 | Supply & fix in repair 15mm bore stop valves chromium plated cast copper alloy, fancy type screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipes (concealed type) all as specified and as directed. |
| 77 | Supply & fix in repairs angle cock chromium plated, fancy type, screwed both ends for iron pipe or for union and fixed, suitable for 15 mm bore pipe, complete all as specified. Jaquar Cat No OPP15053PM all as specified and as directed. |
| 78 | Supply & fix in repairs cast copper alloy, chromium plated toilet paper holder, complete all as specified and as directed. |
| 79 | Supply & fix in repairs chromium plated health faucets (hand held shower type) with shut off valve (thumb or push button type) to allow controlled and continuous flow of water with adequate length and wall mounted pedestal for hanging the faucet etc complete. Parryware cat no T9805A1 or Equivalent in CERA/Hindware all as specified and as directed. |
| 80 | Supply & fix in repairs PVC flexible waste pipe 32/40mm dia and length of 600mm (min) for urinals/WHB/sink all as specified and as directed. |
| 81 | Supply & fix in repairs cast copper alloy, chromium plated towel ring all as specified and as directed. |
| 82 | Supply & fix in repairs cast copper alloy, brass chromium plated towel rail, 600mm long complete all as specified and as directed. |
| 83 | Supply & fix in repairs overhead shower 120 x 120mm size single flow (Face plate Stainless steel and ABS body in chrome finish) with Rubit cleaning system all as specifid and as directed. Jaquar Cat No OHS-CHR-1667. |
| 84 | Supply & fix in repairs waste coupling, brass, chromium plated with long shank, half thread, 32mm dia, for WHB/urinal etc. complete all as specified and as directed. |
| 85 | Supply & fix PVC connections 15mm size with PTMT nuts of length 450mm all as specified and as directed. |
| 86 | Supply & fix for flora centre hole basin mixture including CP extension nipple as required complete all as specified and as directed.(Hindware F570014 or Equivalent in Jaquar/CERA approved by GE) |
| 87 | Supply & fix 15 mm bore sink cock swan neck (wall mount installation) type with chrome finish complete all as specified and as directed. Jaquar Cat No LYR 383473 or Equivalent in Hindware/CERA approved by GE) . |
| 88 | Supply & fix for Bathroom plastic cabinet of size 0.45 x 0.55 x 0.12 mtr with mirror complete all as specified and as directed by Engr-in-charge.Make :- Nilkamal, Cello or Equivalent |
| 89 | Supply & fix multi purpose glass corner shelf of size 300 x 300 mm, clear in color with stainles steel wall brackets and two grill bars, approved quality complete all as specified and as directed. |
| 90 | Supply & fix wall mounted kitchen utensil dish rack, made of stainless steel, weight not less than 5 Kg, size 0.90m x 1.00m (Approx) of approved design and make complete all as specified and as directed. |
| 91 | Taking up or down steel tubing and connectors 25-32mm bore in new or old position (wall, ceiling, floor etc.) all as specified and as directed. |
| 92 | Supplying and laying of 32 mm dia Chlorinated Polyvinyl Chloride (CPVC) pipes SDR 11,having thermal stability for hot & cold water supply, including all CPVC plain SDR 11& brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints on walls/ceiling or laying in floors,Concealed work complete all as specified and as directed. |
| 93 | Supplying and laying of 25 mm dia Chlorinated Polyvinyl Chloride (CPVC) pipes SDR 11,having thermal stability for hot & cold water supply, including all CPVC plain SDR 11& brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints on walls/ceiling or laying in floors, Concealed work complete all as specified and as directed. |
| 94 | Supplying and laying of 20 mm dia Chlorinated Polyvinyl Chloride (CPVC) pipes SDR 11,having thermal stability for hot & cold water supply, including all CPVC plain SDR 11& brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints on walls/ceiling or laying in floors,Concealed work complete all as specified and as directed. |
| 95 | Supply & fix PP-R Gate valves (brass insert) as per requirement of the site for Outer dia of pipes 20 mm all as specified and as directed. |
| 96 | Supply & fix PP-R Gate valves (brass insert) as per requirement of the site for Outer dia of pipes 25 mm all as specified and as directed. |
| 97 | Supply & fix PP-R Gate valves (brass insert) as per requirement of the site for Outer dia of pipes 32 mm all as specified and as directed. |
| 98 | Supply & fix Male Brass Threaded Adaptor (MTA/ MBTA) for CPVC PIPE OUTER DIAMETER 20 mm all as specified and as directed. |
| 99 | Supply & fix Male Brass Threaded Adaptor (MTA/ MBTA) for CPVC PIPE OUTER DIAMETER 25 mm all as specified and as directed. |
| 100 | Supply & fix Male Brass Threaded Adaptor (MTA/ MBTA) for CPVC PIPE OUTER DIAMETER 32 mm all as specified and as directed. |
| 101 | Supply & fix Female Brass Threaded Adaptor (FTA/ FBTA) for CPVC PIPE OUTER DIAMETER 20 mm all as specified and as directed. |
| 102 | Supply & fix Female Brass Threaded Adaptor (FTA/ FBTA) for CPVC PIPE OUTER DIAMETER 25 mm all as specified and as directed. |
| 103 | Supply & fix Female Brass Threaded Adaptor (FTA/ FBTA) for CPVC PIPE OUTER DIAMETER 32 mm all as specified and as directed. |
| 104 | Supply & fix Tank Adaptor for CPVC PIPE OUTER DIAMETER 32 mm all as specified and as directed. |
| 105 | Supply & fix Tank Adaptor for CPVC PIPE OUTER DIAMETER 25 mm all as specified and as directed. |
| 106 | Removal of air lock in internal water supply system of pipe of any dia all as specified and as directed. |
| 107 | Cleaning of water tank exc 250 & n.exc 500 lit, including cleaning all scales and dirts from inside of tank using bleaching powder and washed with water, complete all as specified including taking down and re-fixing of float valve. Including mentioning date of cleaning on water tank using white synthetic enamel paint as existing complete all as specified and as directed. Note :- After Cleaning of water tank, The rep of contractor shall be checked during water supply time and ensure water is reaching to the qtr and float valve is working properly and no leakage at joints. |
| 108 | All as per srl item No. 107 here-in-before but exc 500 & n. exc 1000 lit, complete all as specified and as directed. |
| 109 | Supply & fix in repairs PVC Lid/ cover for 500 lit to 1000 lit Capacity water tank , complete all as specified and as directed. |
| 110 | Supply & fix in repairs three layer anti microbial rotational moulded PVC water storage tanks 500 ltr capacity (cylindrical vertical with threaded type cover and White colour) hoisted and fixed in position all as specified including taking down old broken/cracked water tank and reconnecting the water pipe line in position. |
| 111 | All as per srl item No 110 here -in-before but 750 Ltr capacity and -ditto- all as specified and as directed. |
| 112 | All as per item No 110 here-in-before but 1000 Ltr capacity and -ditto- all as specified and as directed. |
| 113 | Supply & fix in repairs Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed 20 mm dia all as specified and as directed. |
| 114 | Supply & fix in repair Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed 25 mm dia all as specified and as directed. |
| 115 | Supply & fix in repair Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed 40 mm dia all as specified and as directed. |
| 116 | Demolition of wall and ceiling boards (fiber, pulp, insulation etc.) or insulation boards/ slabs/ any thickness including cover fillets all as specified and as directed. |
| 117 | Supply & fix anodised aluminium snap grid frame work for false ceiling (size of grid 605x605mm) complete all as specified and as directed. |
| 118 | Supply & fix hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long complete all as specified and as directed. |
| 119 | Material & labour 4mm thick non-asbestos fiber cement building boards fixed or laid/inserted to timber, GI/aluminium framework with screws all as specified and as directed. |
| 120 | Taking down serviceable bib tap, angle cock, stop cock, heath fauset etc and cleaning, servicing, putting washer etc and refixing on same pipe line all as specified and as directed. |
| 121 | Taking down , repairing & refixing of builders hard ware items like handles, hinges, bolts, towerbolts, sliding bolt etc using necessary screws at the same position all as specified and as directed. |
| 122 | Supply & fix in repairs Mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed. |
| 123 | Taking down serviceable wire mesh & refixing the same using nessary beadings, nails etc.all as specified and as directed. Please Enable Macros to View BoQ information |
