|
| 1 | M&L PCC 1:4:8 type D2 (using 40mm graded granite stone aggregate) as in foundation, filling and mass concrete, with and including demolition of existing cement concrete [unreinforced] in ground floors and paving's n exc 15cm thickness (below or above ground level), complete all as specified and as directed. |
| 2 | M&L for Pre-cast cement concrete solid block masonary type C1, 1:3:6 (using 20 mm graded stone aggregate) exc 10 cm width and setting in CM 1:6, with and including demolition of existing brick work of any description, complete all as specified and as directed. |
| 3 | M&L for 25mm thick (measured solid) Precast RCC Jallies 1:2:4 type B0 (using 12.5mm graded stone aggregate) as in louvers and jallies and similar articles set in CM 1:4, finished plain fair faces, including necessary all mouldings, formwork etc., with and including demolition of existing u/s precast RCC jallies of any type, complete all as specified. |
| 4 | Steel formwork to sides and soffits of floor or roof beams, cantilevers, bressummers, lintels, shelves, lintel beams, RCC bands, complete all as specified. |
| 5 | M&L for Reinforced cement concrete type A1 1:1½:3 (nominal mix)using 20mm graded crushed stone aggregate as in lintel /coping beam, with and including demolition of existing reinforced cement concrete, complete all as specified and as directed. |
| 6 | M&L for Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing, confirming to Fe410-W (Gde Fe-250 Quality 'A'), with and including distantling existing steel work of any description, complete all as specified and as directed. |
| 7 | S&F Mild steel framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work of water tanks and similar work conforming to Fe-290 Gde- E-165, with and including dismantling existing mild steel work of any description, complete all as specified and as directed. |
| 8 | M&L for Preparation of new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and as directed. |
| 9 | M&L for Preparation of old steel surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint over a coat of red oxide primer, complete all as specified and as directed. |
| 10 | M&L for Round bars 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips or welded, confirming to Gde Fe-290 Gde-165, with and including dismantling wrought iron or mild steel work of any description, complete all as specified and as directed. Please Enable Macros to View BoQ information |
| 11 | M&L for Round bars 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips or welded, confirming to Gde Fe-290 Gde-165, with and including dismantling wrought iron or mild steel work of any description, complete all as specified and as directed. Please Enable Macros to View BoQ information |
