|
| 1 | M&L sunken treatment of Toilet/Bathroom( Including Demolition) as in following steps: i) Top of RCC slab in sunken portion including peripheral beams shall be plastered with 15mm thick in cement mortar 1 : 3 using approved water proofing compound @ 3% by weight of cement finished even and smooth using extra cement, curved at the junctions. ii) Apply two coats of epoxy resin/polymer modified cementations coating like brush bond of FOSROK/SIKA/Pedilite or equivalent, both on floor & beams. iii) Sunken slabs to be given 1:20 slope outward 25mm GI pipe spout with 300 mm projection beyond outer surface of wall shall be provided. iv) Water tightness of sunken portion to be tested by ponding with water for 72 hours. In case of even a slight mark of seepage, the portion to be treated and ponding shall be carried out again to confirm the water tightness of sunken slab. v) The sunken portion will be filled with lean concrete 1:4:8 type D2 using brick aggregates to required depth. Note : No cutting in roof slab/beam shall be allowed for passing of CI pipes & fittings.The stage of water proofing to sunken slab shall be passed by Eng-in-charge/GE. |
| 2 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises complete all as specified and directed |
| 3 | Demolition of cement concrete in floors n.exc 15 cm thick in ground floor (below or above ground level) and in any position all as specified |
| 4 | M&L for PCC 1:2:4 type B-1 using 20mm graded stone aggragate as in subbase 40 mm thick complete all specified and directed by engr in charge complete all as specified and directed |
| 5 | M&L for Virified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed of CM 1:4 complete all as specified and directed |
| 6 | M&L for Virified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering with CM 1:3 on fair faces of brick work or concrete surfaces as in skirting all as specified. |
| 7 | M&L for Non - skid coloured Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed of CM 1:4 complete all as specified and directed |
| 8 | M&L for Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed of CM 1:4 complete all as specified and directed |
| 9 | M&L for Non - skid coloured Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering with CM 1:3 on fair faces of brick work or concrete surfaces as in skirting all as specified. |
| 10 | Material and labour for 450x350x7mm thick glazed ceramic tiles coloured set and jointed in neat cement slurry and pointed in coloured cement over and including 10mm thick rendering with CM 1:3 on fair faces of brick work or concrete surfaces as in dado of bathroom, toilet and kitchen all as specified. |
| 11 | Dismantling of wall and ceiling board or insulation boards/slabs/blanckets/any thickness including cover fillets complete all as specified and directed |
| 12 | S&F 6 mm thick ply wood, grade BWR, type BB, fixed with nails to timber frame work on wall surfaces complete all as specified and directed |
| 13 | S&F 4 mm thick ply wood, grade BWR, type BB, fixed with nails to timber frame work on ceiling surfaces complete all as specified and directed |
| 14 | M & L for 50 mm thick II nd class Hard wood clean sawn boarding with butt joints fixed with nails in any situation complete all as specified and directed |
| 15 | M & L for 2 nd class Hard wood plain fillets, square, rectangular or triangular in section,wrought, secured with nails or brads, sectional area exc 3 but n.exc 6 sq.cm complete all as specified and directed |
| 16 | M&L for preparation of new wooden surfaces of any description, not other wise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed |
| 17 | Supply and fix 600mmx600mmx4mm thick ‘E’ Board Classic (Make-Everest industries Ltd) as in false ceiling including supply and fixing GI ‘Tee” grid frame work made of special section of M.S galvanized sheet 0.30mm thick , bottom portion painted with cellular nitro painting, warping the suspending wire around the existing wooden/steel purlin /rafter for suspending grid frame work of size 605mmx605mm suspended with 4 mm dia GI wire @ 1200mm c/c on main Tee and fixed to T-grid with the help of level clip or as per manufacturer direction. The section consisting of main Tee 37mmx24mmx0.60mm, cross runner tee 37mmx24mmx0.60mm and perimeter angle of 24mmx24mmx0.50mm thick. Perimeter angle to be fixed to wall with GI screw of 40mm long @ 450 mm c/c along the perimeter of wall including applying two coats of distemper oil emulsion complete all as specified and directed |
| 18 | M&L for Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre complete all as specified and directed |
| 19 | M&L for 8mm thick Seamless calcium silicate ceiling made out of 1800 x 1200 mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25 mm long self drilling and tapping screws having phillips head with under head cutter at 200 mm centre to centre, including finshing the joint of face board with specially formulated jointing compound and 48 mm wide fibre tape to provide seam less finish (Frame work for ceiling shall be measured and paid separately) complete all as specified and directed |
| 20 | Taking down chowkats or frames with shutters (without taking off shutters from the frames) area exceeding 1.50 Sqm but not exc 4 Sqm. |
| 21 | Taking down chowkats or frames with shutters (without taking off shutters from the frames) area not exceeding 1.50 Sqm |
| 22 | S & F 2nd class hard wood plain solid straight chowkats and frames, wrought, framed rebated on the solid rounded or chamfered, put together with glue pinned at joints complete all as specified and directed |
| 23 | S & F 2nd class hard wood plain framed panelled shutter 35mm thick (any number of panels) with panels of timber flat on both sides, feather edged or of veneered particle board medium density, wood particle board with commercial face veneer 30mm thick complete all as specified and directed |
| 24 | S&F 30mm flush shutters, solid core construction with particle board core and plywood face panels, commercial type on both side and both face is covered with decorative face veneer with lipping/frame tp match all as completed and specified as directed. |
| 25 | S & F 30mm thick 2nd class hard wood glazed and skeleton shutters open rebated and prepared to receive glass, gauze etc but divided into squares, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and as directed |
| 26 | S&F MS window guard bars, window frames etc articles confirming to Fe 410-0 or Fe 310-0 complete all as specified and directed |
| 27 | S & F 100mm size mild steel butt hinges medium weight cold rolled and fixed. |
| 28 | S & F 75mm size mild steel butt hinges medium weight cold rolled and fixed. |
| 29 | S& F Aluminium anodised barrel tower bolts 150mm long of extruded section and fixed |
| 30 | S& F Aluminium anodised barrel tower bolts 100mm long of extruded section and fixed |
| 31 | S & F 150mm size extruded aluminium alloy handles, fabricated type anodised |
| 32 | S & F 100mm size extruded aluminium alloy handles, fabricated type anodised |
| 33 | S & F aluminium alloy, anodised, sliding door bolts 300mm size with hasp, staple (bolt type) and fixing clips of sheets, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and directed |
| 34 | S&F pre coated mild steel floor door stopper ,tongue anodized 140mm length including vulcanised rubber piece complete all as specified and directed |
| 35 | M&L for power coated anodised aluminium frame for doors, windows, ventilatores with one or more rebated including joiing cleat for fixing etc complete all as specified and directed |
| 36 | S & F Anodised aluminium window and ventilator shutters, fixed type without sash barsaluminium section weighing 0.55 kg/m including necessary joining cleats, glzing clips,rubber packing,anodised aluminium snap beading,screws etc and power coating of any colour(thickness of powder coating not less than 50 micron.) complete all as specified. |
| 37 | M & L for 4.80 mm Sheet glass, ordinary quality and glazing with aluminium clip and beading in square exc 0.5 sq. m in each pane |
| 38 | S & F GI steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm etc all as specified. |
| 39 | Dismatling of mild steel work any description |
| 40 | M&L for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc conforming to Fe 290 (Gde E-165) complete all as specified and directed |
| 41 | M&L for Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete conforming to Fe 290 (Gde E-165) complete all as specified and directed |
| 42 | M & L for Preparation of new or previously untreated steel surface and applying two coat of synthetic enamel paint over a coat of red oxide primer to steel and iron surfaces of any description over 10 cm in width or girth not otherwise described including preparation of new steel surfaces complete all as specified and directed |
| 43 | Dismantling plain or corrugated steel sheeting of any thickness as in roof coverings complete all as specified and directed. |
| 44 | Supply and Fix 0.63 mm thick galvanised, corrugated mild steel sheeting with two corrugation side lap, fixed with L-type or J-type or cranked hook bolts in lieu of screws and washers, in roofs, walls etc. with grade of zinc coating 275 gsm complete all as specified and as directed. |
| 45 | S & F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering cladding to wall, fixed with self tapping screws as specified. |
| 46 | S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified. |
| 47 | M & F for Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as specified and directed |
| 48 | M&L 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specified and directed |
| 49 | S&F in rep PVC (SWR) WC connector 110mm dia. |
| 50 | S&F in repair Vitreous China Squatting pan 'Orissa pattern' size 580 x440 mm white with integral foot rest complete all as specified and directed |
| 51 | S&F in repairs 10 ltrs capacity PVC valveless syphonic action type flushing cistern low level white with inlet ball valve, float, chain and pull and brackets etc complete all as specified and directed |
| 52 | S & F in repair PVC connection 15mm dia 450 mm long with brass check nuts and washers complete all as specified and directed |
| 53 | S&F in repair vitreous china wash down water closet pan of pedestal pattern, white with 'P' or 'S' traps, including connecting to trap and to flushing pipe etc complete all as specified. |
| 54 | S & F in repair plastic water closet seat cover, white closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed |
| 55 | Dismantling of CI soil, rain water pipes, cast and vent pipes of any dia, any pattern including all fittings. |
| 56 | S&F PVC (SWR) pipes single socketed 110mm dia in any length with rubber ring joints fixed to walls complete all as specified and directed |
| 57 | S&F in rep PVC (SWR) bends any radius, bend 110mm dia with access door |
| 58 | S&F PVC (SWR) pipes 75 mm bore single socketed, in any length with rubber ring joints, laid in trenches,wall or in floors complete all as specified and directed |
| 59 | S&F in repair PVC bends any radius 75mm bore |
| 60 | S&F in rep PVC (SWR) floor trap, 75mm dia outlet, plain with grating incl jointing with solvent cement. |
| 61 | Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed |
| 62 | Demolition for Brickwork or precast concrete articles, built in cement/lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles |
| 63 | M&L for PCC 1:3:6 type C-1(20 mm graded aggregate) precast cement concrete block masonry with solid blocks exc 10 cm in width and setting in CM 1:6 etc complete all as specified and directed |
| 64 | M&L Rendering 15mm thick on fair faces of brick work or concrete surface in cement plaster 1:4, finished even and smooth without using extra cement with WPC completed all as specified and directed. Note : WPC will be measured and paid separately) |
| 65 | Supply only integral water proofing compound |
| 66 | M & L 100mm thick cement concrete type C2 (1:3:6) using (40mmgraded aggr.) as in sub base complete all specified and directed |
| 67 | M&L for 20mm thick screed bed or bedding layer in CM (1:6) for laying floor finishes complete all as specified and directed |
| 68 | M&L for Chequered cement concrete tiles 200x200x25/300x300x25mm etc. set and jointed and pointed in neat cement slurry in floor with grey cement and pigment all as directed. |
| 69 | M&L for 40 mm thick PCC 1:2:4 type B1 (using 20 mm graded granite stone aggregate) in floorings including finishing the surface even and smooth using extra cement all as specified |
| 70 | M&L for 60mm thick Machine pressed precast concrete interlocking paver block with grey cement and no pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade complete all as specified and directed |
| 71 | M&L for Sand filling under floors or in foundations including watering and consolidation Please Enable Macros to View BoQ information |
