|
| 1 | Supply and Installation of 5m(4m plus 1m) decorative pole along with decorative bracket made from a combination of cast alluminium and pre-galvanized pipe. The pole features a decorative design in two sections witch single piece construction. The bottom section is 750mm in height with a base diameter of 460mm, gradually reducing to 415mm up to the top ring at 305mm, weighing not less than 25kg. The upper section is 600mm high, starting at a diameter of 170mm, expanding to 220mm in the center, and reducing again to 170mm, weighing no less than 10kg. Both section are gravity die-cast. The pole includes a pre-galvanized segment of 4000mm with a thickness of 3.6mm, featuring a cast alluminium final weighing not less than 2.5kg. It has arrangements for flower pots on both sides, each with a 600mm long overhang and a dia of 32mm, backlit GUG, and logo of University, provision for a camera, and a V shaped stand provided at the upper section. The round base plate dimensions are 570mmx12mm thick,weighing no less that 27kg. The pole is designed for mounting on a concrete pedestal with four foundation bolts measuring M16 x 450mm . An internal service window is provided in the lower casted base. The pole is duly primer coated and polyurethane painted with an antique finish in dual shades, followed by a final coat of PU paint with a dry film thickness not less than 90 microns. The pole is suitable for an ornamental single-arm bracket measuring 1000mm long with a 900 mm overhang. The bracket is designed for an ornamental LED drop-down fixture. Fixture:- Supply and installation of an ornamental 100W LED drop-down luminaire 120-130 watt 10KV surge protection made of spun aluminium housing with dimensions not less than 625mm x 630mm, duly powder-coated and PU painted with a PC clear diffuser for high illuminance glare lightning, High lumen LEDs mounted on pressure die -cast heat sinks, IP-66 protection powered by phillips driver, and 10KV external surge protection complete in all respects ( design of pole, bracket, and light fitting as per approved drawing). |
| 2 | Supply and Installation of an ornamnetal decorative pole, 8mtr in height, made from multiple sections of pre-GI pipe: 140x3.5x200mm at the base, 114x3.6x2000mm in the middle, and 90x2000mm at the top. It is welded to an MS base plate of 420x420x20mm, with alluminium decorative embelishments at each section.The base includes an alluminium cast design, 450 mm in heights, enhancing to appearance. The pole supports a double beacket of 2meters Supply and installation of a double arm bracket,1250mm overhang each side ( total 2500mm), with three bows and laser-cut design, designed to hold two fixtures. The pole is primer-coated and painted with polyurethane paint, at least 90 microns thick, and features a service window with MCB connector. Concord crown Fixture:- Supply and installation of a decorative 120-130 watt drop-down fixture, made of cast and spun alluminium with sturdy extruded arms, total eight not less that 1110 mm. Equipped with high-power LEDs producing 180 lumens, mounted on a pressure die-cast heat sink for thermal management and durability. The fixture includes a single-piece polycarbonate diffuser, unbreakable, size 440x340mm reducing to 225mm, and is primer-coated and painted with polyurethane paint. It features a laser -cut crown design on top, 520x110mm, complete in all respect as per approved drawing. |
| 3 | Supply and Installation of 3mtr decorative mild steel galvanizede tubular pole with varying profiles. The bottom profile is 1000x114mm, and the top profile is 2000x60mm, with cast aluminium embellishmentsE3. The pole includes a window and fixed plate at the bottom. It is primer coated and painted. Fixture:- Supply and installation of a 45 watt ornamental LED post top luminaire with an aluminium housing, powder coated/PU painted, and equipped with a clear/frosted PC/PM diffuser. The luminaire features a sturdy triple arm mount and high lumen LEDs on aluminium heat sinks. Complete in all respect as per approved design specifications. |
| 4 | Shifting and erection of existing Hot Dip Galvanized octagonal pole of 3mm thickness, 8 Metre Long pole with top dia 100 mm and bottom 200 mm with base plate of size 350 x 350 x 20 mm. with base plate including cost of nut and bolts , earthing studs, Integral Cable termination arrangement 5 mm thick Bakelite base plate on suitable welded MS/GI bracket 32 A four way connector 2 no 1 O A SP MCB ,end cover and all accessories as supplied by the manufacture including complete in all respects and as per directions of Engineer-in-charge. |
| 5 | Supply and erection of MS pedestal of size 600x800x300mm including following meter: MCCB 100A 4pole 25K-1bus bar copper 100A 4pole- 1TPN MCB 63A-2 and 100A bus bar timer :- Quartz Analog/ Digital 24hour operation (LandT/ Siemens/ Schnider) Contactor:- 3pole 40A, 415Volt. (LandT/Seimens/Schnider) to complete the job in all respect upto the entire satisfaction of Engineer-In-Charge of the work. |
| 6 | [23.22.1.1]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 1.1. Supply and erection of Modular case circuit breaker single pole/4 pole on existing wall/pedestal/Panel including bounding to earth and making necessary connections required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the work. Double pole MCCB 16 to 63 Amp, 25 Ka [Through Rate] |
| 7 | [23.5.6.2]COPPER WIRING IN EXISTING PVC/MS CONDUIT PIPE SURFACE/RECESSED FOR ELECTRICAL POINTS 6.2. Wiring main and sub mains in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in existing MS/PVC Conduit etc as required. 1 run of Size 2.50 Sqmm(1.1.80mm) [Through Rate] |
| 8 | [23.7.6.2]PVC CONDUIT PIPE ONLY (SURFACE OR RECESSED) FOR ELECTRICAL POINTS 6.2. Supply and erection of PVC CONDUIT ISI marked (Medium) recessed in wall/ceiling etc. including the cost of PVC bends, inspection boxes, iron hooks and cement concrete etc. complete in all respect up to the entire satisfaction of Engineer-in-Charge of work. PVC pipe of 25 mm dia. [Through Rate] |
| 9 | [24.1.1]EARTHING AND LIGHTENING ARRESTOR 1. Earthing with GL earth pipe 4.5 m long and 40 mm dia with masonry enclosures on the top etc. (but without charcoal or coke and salt) as required. [Through Rate] |
| 10 | [24.1.2]EARTHING AND LIGHTENING ARRESTOR 2. Extra for using salt and char coal/coke for pipe earth electrode as required. [Through Rate] |
| 11 | [24.1.3]EARTHING AND LIGHTENING ARRESTOR 3. Earthing with G.I. earth plate 600 mmx 600 mm x 6 mm thick including accessories and providing masonry enclosures with cover plate having locking arrangement and watering pipe etc. (but without charcoal or coke and salt) complete as required. [Through Rate] |
| 12 | [24.1.6]EARTHING AND LIGHTENING ARRESTOR 6. Supplying and laying 25mm x 3mm G.I. strip at 0.5 metre below ground as strip earth electrode including soldering etc. as required. [Through Rate] |
| 13 | [24.11.32]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING AND ERECTION/LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR CABLE 0.75 METER BELOW GROUND LEVEL COVERED WITH SAND AND BRICKS INCLUDING EXCAVATION AND REFILLING OF TRENCHES 32. 25 Sq mm 4 core (Arm.) [Through Rate] |
| 14 | [24.2.10]LT CABLE 10. Supply and erection of cable route marker made of 50 cm long 10 mm dia M.S. Rod welded/riveted at the top with 10 cm dia 3 mm thick MS plate inscribed with cable word on it, having a cross arm 30 cm long of the same dia welded at the bottom, in exiting trench 45 cm below ground level. [Through Rate] |
| 15 | [24.4.15.1]STREET LIGHT 15.1. B.S.E.N. 10025 High Masts \\"Supply, installation, testing and commissioning of 12.5 mtr. long High Mast manufactured from B.S.E.N. 10025 or equivalent grade material in, 2 (two) section hot dip, galvanized inside and outside in single dip, suitable for wind velocity as per IS 875 Part-3 suitable for 6 nos. luminaire loading fully motorized (power tool) with starter & cable complete along with standard accessories supplied by the manufacturer with 3 nos. steel wire rope double drum system and twin dome aviation light with LED without foundation but including cost of set of foundation nut and bolts, installation at site complete in all respect upto entire satisfaction of Engineer -in-ChargeThickness of Top and Bottom Section = 3 mm (minimum)Top Dia = 150 mm and Bottom Dia = 360mmThickness of Galvanization - Top = 65 micron (minimum) and Bottom = 85 micron (minimum)\\" [Through Rate] |
| 16 | [24.4.15.2]STREET LIGHT 15.2. B.S.E.N. 10025 High Masts \\"Supply, installation, testing and commissioning of 16 mtr. long High Mast manufactured from B.S.E.N. 10025 or equivalent grade material in, 2 (two) section hot dip, galvanized inside and outside in single dip, suitable for wind velocity as per IS 875 Part-3 suitable for 9/12 nos. luminaire loading fully motorized (power tool) with starter & cable complete along with standard accessories supplied by the manufacturer with 3 nos. steel wire rope double drum system and twin dome aviation light with LED without foundation but including cost of set of foundation nut and bolts, installation at site complete in all respect upto entire satisfaction of Engineer -in-ChargeThickness of Top and Bottom Section = 3 mm & 4mm (minimum)Top Dia = 150 mm and Bottom Dia = 410mmThickness of Galvanization - Top = 65 micron (minimum) and Bottom = 85 micron (minimum)\\" [Through Rate] |
| 17 | [24.4.5]STREET LIGHT 5. Supply and erection of Single Phase weather proof M.S. box of size 20 cm x 15 cm x 10 cm with hinged cover made of 2 mm thick MS sheet, locking arrangements, housed in wall/fixed on pole , including the cost of 1 no 4 way 16 A Bakelite connector, 1 no. 6 amp SP MCB and 1 Nos. 16 amp. neutral links fixed on Bakelite sheet in the M.S. box including painting and necessary connections. [Through Rate] |
| 18 | [24.4.6]STREET LIGHT 6. Supply and erection of Three Phase weather proof M.S. box of size 30 cm x 20 cm x 15 cm with hinged cover made of 2 mm thick MS sheet, locking arrangements, housed in wall/fixed on pole , including the cost of 1 no 4 way 16 A Bakelite connector, 1 no. 16 amp TP MCB and 4 Nos. 16 amp. neutral links fixed on Bakelite sheet in the M.S. box and necessary connections. [Through Rate] |
| 19 | [24.5.2.4]MISCELLANEOUS ITEMS 2.4. S/E mark double walled corrugated (DWC) HDPE, pipe 10 Kg/Cm2 ,laid 0.75 Metre below ground level including digging and refilling of earth including cost of suitable size socket/coupler for HDPE pipe including the cost of labour and material required to complete the job in all respect up to the entire satisfaction of Engineer in charge of the work. DWC/HDPE pipe 90/75 mm outer dia/inner dia [Through Rate] |
| 20 | [24.8.1]RCC FOUNDATIONS FOR OCTAGONAL POLES 1. Providing RCC foundation of M25 grade (1 Cement:1 Stone aggregate: 2 Coarse sand) i/c excavation, steel reinforcement (Fe 500) @80 kg/cum of concrete contents, concrete cover 50mm, anchor bolts etc. over a bed of PCC 1:5:10 of required dimensions for octagonal poles of various heights as per following specifications complete in all respects and as per directions of Engineer-in-charge 3m high pole [Through Rate] |
| 21 | [24.8.3]RCC FOUNDATIONS FOR OCTAGONAL POLES 3. Providing RCC foundation of M25 grade (1 Cement:1 Stone aggregate: 2 Coarse sand) i/c excavation, steel reinforcement (Fe 500) @80 kg/cum of concrete contents, concrete cover 50mm, anchor bolts etc. over a bed of PCC 1:5:10 of required dimensions for octagonal poles of various heights as per following specifications complete in all respects and as per directions of Engineer-in-charge 5m high pole [Through Rate] |
| 22 | [24.8.6]RCC FOUNDATIONS FOR OCTAGONAL POLES 6. Providing RCC foundation of M25 grade (1 Cement:1 Stone aggregate: 2 Coarse sand) i/c excavation, steel reinforcement (Fe 500) @80 kg/cum of concrete contents, concrete cover 50mm, anchor bolts etc. over a bed of PCC 1:5:10 of required dimensions for octagonal poles of various heights as per following specifications complete in all respects and as per directions of Engineer-in-charge 8m high pole [Through Rate] |
| 23 | [24.9.1]RCC FOUNDATIONS FOR HIGH MAST OCTAGONAL POLES 1. Providing RCC foundation of M25 grade (1 Cement:1 Stone aggregate: 2 Coarse sand) i/c excavation, steel reinforcement (Fe 500) @ 75 kg/cum of concrete contents, concrete cover 50mm, anchor bolts etc. over a bed of PCC 1:5:10 of required dimensions for high mast octagonal poles of various heights as per following specifications complete in all respects and as per directions of Engineer-in-charge 12.5 m high mast pole [Through Rate] |
| 24 | [24.9.2]RCC FOUNDATIONS FOR HIGH MAST OCTAGONAL POLES 2. Providing RCC foundation of M25 grade (1 Cement:1 Stone aggregate: 2 Coarse sand) i/c excavation, steel reinforcement (Fe 500) @ 75 kg/cum of concrete contents, concrete cover 50mm, anchor bolts etc. over a bed of PCC 1:5:10 of required dimensions for high mast octagonal poles of various heights as per following specifications complete in all respects and as per directions of Engineer-in-charge 16m high mast pole [Through Rate] Please Enable Macros to View BoQ information |
