|
| 1 | Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in-charge.Note - 1. Item to be applicable in urban areas having directions for restricted hours for movement / plying of load carrying motor vehicle of 3.5 cum or more.2. Voids @20% for solids and 50% for rock shall be dedcuted from fully loaded truck measurement to arrive at the net quantity for payment in case of direct measurement is not possible.3. The cost is inclusive of necessary permisiion from statutory authorities for dumping the debris/excess earth outside department premises4. Debris generated for dismantling items of BOQ or other debris situated inside campus as instructed by EIC will be considered in this item only. Other debris generated during work will be disposed by contractor at their own expense. |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil |
| 3 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lift. |
| 4 | Supplying and filling in plinth with sand under floors, including watering, ramming consolidating and dressing complete. |
| 5 | Supplying cement OPC or PPC or PSC of grade 43 or 53 (as decided by EIC) in (50 kg) bags in good condition including delivery as specified location. |
| 6 | Supplying of Birla White cement in 5kg bags in good condition including delivery as specified location. |
| 7 | Supplying chemical emulsion in sealed containers including delivery as specified Chlorpyriphos/ Lindane emulsifiable concentrate of 20% |
| 8 | Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration |
| 9 | Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) :Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mmapart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration |
| 10 | Treatment at points of contact of wood work by chemical emulsion Chlorpyriphos/ Lindane (in oil or kerosene based solution- to be supplied by contractor ) @ 0.5 litres per hole by drilling 6 mm dia holes at downward angle of 45 degree at 150 mm centre to centre and sealing the same. |
| 11 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 12 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 13 | Centering and shuttering including strutting, propping etc. and removal of form work for Foundations, footings, bases for columns etc. |
| 14 | Extra for addition of synthetic Polyester triangular fibre of length 12mm, effective diameter 10-40 microns and specific gravity of 1.34 to 1.40 in cement concrete/ RCC/Flooring/water retaining structures by using 125gms of synthetic Polyester triangular fibre for 50 g cement used as per directions of Engineer-in-Charge. |
| 15 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 16 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excludingcost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 17 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 18 | Providing and constructing BRICK MASONRY in cement mortar as per mixes stipulated below using approved well burnt bricks of \\"CLASS DESIGNATION\\" (Classification as per I.S.1077-1986) as specified below, including raking out joints 10mm deep wherever required, curing, etc; complete at all lead and lifts all as per specifications (The mix ratio specified is for cement : coarse sand) USING BRICKS OF CLASS DESIGNATION \\"3.5\\"(Minimum Average Compressive strength not less than 3.5 N/sqmm) In foundation and plinth in cement mortar 1:6. Price includes fixing of chair bracket/rag bolt into masonary Complete all as directed by EIC. |
| 19 | Providing and constructing BRICK MASONRY in cement mortar as per mixes stipulated below using approved well burnt bricks of \\"CLASS DESIGNATION\\" (Classification as per I.S.1077-1986) as specified below, including raking out joints 10mm deep wherever required, curing, etc; complete at all lead and lifts all as per specifications (The mix ratio specified is for cement : coarse sand) USING BRICKS OF CLASS DESIGNATION \\"3.5\\"(Minimum Average Compressive strength not less than 3.5 N/sqmm) superstructure above plinth level up to floor V level in cement mortar 1:6. Price includes fixing of chair bracket/rag bolt into masonary Complete all as directed by EIC. |
| 20 | Providing and constructing HALF BRICK MASONRY walls/partitions in following mixes using approved well burnt bricks of \\"CLASS DESIGNATION\\" (Classification as per I.S. 1077-1986) as specified below, including scaffolding, raking out joints, curing, etc; at all lead and lifts all as directed by the Engineer -in- charge. In SUPERSTRUCTURE UPTO FLOOR-V LEVEL. (The mix ratio specified is for cement : coarse sand) Using bricks of \\"class designation 3.5\\"(Minimum Average Compressive Strength not less than 3.5N/sqmm) In cement mortar 1:4 Complete all as directed by EIC. Price includes fixing of chair bracket/rag bolt into masonary. |
| 21 | Repairs to the existing doors ,window frame and shutter , panel of office rooms,washroom, etc. by replacing part of the member wood with material wood supplied by Institute at site of work by: i) Cutting of the damaged/ decayed portion of the member without disturbing/ removing of the existing part of frame or shutter of door & window.ii) Using wood supplied by Institute including minor repairs / cutting as per the existing member for repairing of the damaged/ decayed portion of the member including cutting,scraping making lap joints for jointing the new wood with old wood work by fixing necessary screws and synthetic adhesive etc. complete.iii) Fixing the repaired door and window frame or shutter in minor repair work & disposing off debris out side colony etc. complete all as directed by the Engineer-in-Charge. Note- Shape and size of frame or shutter should match with existing one. Only damaged portion to be cut out of entire member will be replaced. Cutting and removing of damaged part has to be removed without damage existing floor and wall. Contractor has to consider cost of same in quoted item rate. No extra payment shall be given |
| 22 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (PartI) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.30 mm thick including Stainless steel butt hinges (heavy weight) 100x60x2.5 mm IS : 12817 marked with Stainless steel screws 40 mm |
| 23 | Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). |
| 24 | Providing and fixing Stainless steel SS grade 304, curtain rod 25 mm dia 1.20mm thick, with necessary Stainless steel SS grade 304 brackets, finial, socket as required and based on suitability of curtain rod. 25 mm dia 1.20mm thick fixed with C.P. brass screws and PVC sleeves etc., wherever necessary complete :25 mm dia |
| 25 | Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete :100X58X1.90 mm |
| 26 | Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete :75x47x1.80 mm |
| 27 | Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer Hafele make Item code- 931.84.749 (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 40 kg to 80 kg and door width from 701 mm to 1100 mm), with double speed adjustment with necessary accessories and screws etc. complete. |
| 28 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc.complete-300x10 mm |
| 29 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc.complete-200x10 mm |
| 30 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete-125 mm |
| 31 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete-Twin rubber stopper |
| 32 | Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality and surface preparation for proper bonding.1.0 mm thick |
| 33 | Providing and fixing stainless steel soft closing heavy type telescopic drawer channels of approved make 500 mm long with screws etc. complete as per directions of Engineer- in-charge. |
| 34 | Providing and fixing stainless steel soft closing heavy type telescopic drawer channels of approved make 400 mm long with screws etc. complete as per directions of Engineer- in-charge. |
| 35 | Providing & fixing Godrej Cylinderical round lock Keyed (Classic or equivalent - Tubular lock) for door with SS parts and body with 6 levers with stainless steel 3 numbers of keys with chromium plated brass screws for left hand/right hand and for single leaf shutter of 30mm to 40 mm thickness with brass socket plate. Push button when pressed, won't allow anyone to enter from outside. The lock can operated with key from outside (Exact number for left, right and double shutter shall be ascertained based on site requirement. It shall be matching with existing old door locks). Cost laso includes removing of old damaged lock and minor repairing of wooden shutter. Please Enable Macros to View BoQ information |
| 36 | Providing & fixing Godrej Cylinderical round lock Keyed (Classic or equivalent - Tubular lock) for door with SS parts and body with 6 levers with stainless steel 3 numbers of keys with chromium plated brass screws for left hand/right hand and for single leaf shutter of 30mm to 40 mm thickness with brass socket plate. Push button when pressed, won't allow anyone to enter from outside. The lock can operated with key from outside (Exact number for left, right and double shutter shall be ascertained based on site requirement. It shall be matching with existing old door locks). Cost laso includes removing of old damaged lock and minor repairing of wooden shutter. Please Enable Macros to View BoQ information |
