|
| 1 | Demolition of reinforced cement concrete of any description (reinforcement cut as required to facilitate demoltion) and in any position not otherwise specifically provided for complete all as specified and directed |
| 2 | M&L for Design mix RCC M-30 (using 20mm graded stone aggregate) in Walls, retaining walls,basement walls, ballast walls and the like; anythickness; above top of footings; including attached pilasters and buttresses complete all as specified and directed |
| 3 | M&L for form work to faces of walls retaining walls, abutments, parapets, drain walls and like for flat rough finishesd surface all as specified |
| 4 | M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed |
| 5 | M&L for precast cement concrete block masonary with solid blcoks using PCC 1:3:6, type C1(using 20mm graded stone aggregate) exc 10cm in width, set in CM 1:4 all as spcefied and directed by engineer in charge |
| 6 | M&L for 10 mm thick plaster in CM 1:4 on fair face of concrete surface or brick walls finished even and fair without using extra cement complete all as specified and as directed |
| 7 | M&L for preparing newly plastered wall surface and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali and fungal resistance, dirt resistance exterior paint of required shade (company depot tinted) with silicon additives @ 1.43 litre/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm over new surfaces complete all as specified and directed |
| 8 | Excavation in trenches n. exc 1.5m wide and n. exc 1.5m in depth in hard/dense soil for foundation, etc or for shafts, wells, cesspits, manholes, pierholes, etc n. exc 10 Sqm on plan and getting out complete all as specified and directed |
| 9 | Removing excavated material (any type of soil) to a distance n. exc 50m and depositing where directed at a level n. exc 1.5m above the starting point complete all as specified and directed |
| 10 | M&L Cement concrete 1:4:8 type D2 (using 40mm graded stone aggregate) as in foundations or mass concrete complete all as specified and as directed |
| 11 | M&L for PCC 1:2:4 type B0 (using 12.5mm graded stone aggregate) as in coping including necessary form work complete all as specified |
| 12 | M&L for plain cement concrete 1:3:6 type C1 (using 20mm graded stone aggregate) as in surface channel or drain or benching in manhole including necessary formwork complete all as specified and directed |
| 13 | Forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement including forms, moulds, mitered/stopped ends etc complete all as specified and directed |
| 14 | Returning filling in hard/dense soil including spreading levelling watering and well ramming in layers n. exc 25cm thick complete all as specified and directed |
| 15 | S&F framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar works conforming to Fe-290, Gde-E-165 all as specified and as directed |
| 16 | M&L for applying two coat of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surfaces of any description over 10cm width or girth not otherwise described complete all as specified and directed |
| 17 | Dismantling wrought iron or mild steel work of any description not otherwise provided for all as specified and directed |
| 18 | S&F for stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc, including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc of required size on the top of floor or the side of waist slab with suitable arrangement complete all as specified |
| 19 | Excavation in post hole in hard/dense soil (or similar holes) each n. exc 0.5 cum, getting out, returning filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25cm, watering, and removing surplus soil to a distance n. exc 50m and making good surface complete all as specified and directed |
| 20 | M&L for cement concrete 1:3:6 type C2 (Using 40mm graded stone agrregate) as in foundation of posts, railing and similar work complete all as specified and directed |
| 21 | M&L for mild steel work as posts and struts in fencing including cutting tops as required drilling holes, notching for wires etc and similar works conforming to Fe-290 Gde E-165 complete all as specified and as directed |
| 22 | S&F mild steel Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment (Fe-410W, Gde-E-250 Quality-A) complete all as specified and directed |
| 23 | S&F mild steel screw bolt (Machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, dia of shank 11 to 15 mm and length of bolt exc 5 cm but n. exc 10 cm complete all as specified and as directed |
| 24 | S&F mild steel round bars 10mm dia and over cut to length bent to shape required including cranking, bending spirally for hoping for columns, hooking ends and binding with MS post of grade Fe-410-W (Gde E-250) quality-A or Fe-290 (Gde-E-165) complete all as specified and directed |
| 25 | M&L for applying two coat of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surfaces of any description over n.exc 10cm width or girth not otherwise described complete all as specified and directed |
| 26 | Supply and fix mild steel galvanised PVC coated chain link fencing 3.15mm nominal dia of GI wire, 1.4mm thick PVC coating and average area of aperture 25 sqcm with weight of chain link not less than 3.60 Kg/Sqm complete all as specified and directed |
| 27 | S&F multi wall poly carbonate sheet 4 mm thick with required side lap fixed in position on steel frames as in roof covering/wall partition and railing with required screws etc., complete all as specified and as directed. |
| 28 | Demolition of cement concrete (Un-reinforced) in ground floors and pavings n.exc 15cm thick (above or below GL) complete all as specified and directed |
| 29 | M&L for cement concrete 1:2:4 type B1 (Using 20mm graded stone agrregate) as in foundation of posts, railing and similar work complete all as specified and directed |
| 30 | M&L formwork for rough finished flat surface to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work, vertical or to batter complete all as specified and directed |
| 31 | M&L precast cement concrete block masonry exc. 10 cm width with solid block C1 (1:3:6) (using 20 mm graded stone aggregate) and setting in cement mortar (1:6) all as specified and as directed. |
| 32 | M&L for 10mm thick plaster in CM 1:6 on fair face of concrete surface or brick walls finished even and smooth without using extra cement complete all as specified |
| 33 | S & F 8mm thick fibre cement plank of 0.15m width of any colour fixed in position with suitable screws/ fasteners as per manufactures instructions on aluminium/ mild steel work in wall cladding/garden @ c/c distance of 0.25m including applying two coats of exterior emulsion paint on fibre planks as approved by GE complete all as specified and as directed. Note: Aluminium/ Mild steel work shall be measured and paid seperately. Make : M/S HIL LTD / EVEREST / NCL INDUSTRIES LTD |
| 34 | S&F 12mm WPC white board and fixing it to GI frame work by cutting in adequate shape complete all as specified and directed.Make : Rajshri Plastiwoos/M/s Kumar Arch Tech Pvt Ltd/M/s Navratna Co Speciality Chemicals |
| 35 | Labour only for cutting Wood Plastic Composite (WPC) board 12mm/ 18mm of ACP board 4mm in CNC machine as design and shape chosen by GE complete all as specified and directed. |
| 36 | M&L for applying two coat Duco enamel paint on WPC board over two coat of Akzo Nobel Auto Paints Duco Primer Surfacer (PS) Grey by using Duco thinner, all the surface uneveness have to be fill with french chalk complete all as specified and directed.Note:- i) All the painting on surface will be done by using pressure spary machine. Please Enable Macros to View BoQ information |
