|
| 1 | Demolishing brick work in cement mortar manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead complete all as specified and directed. |
| 2 | Providing and laying in position cement concrete 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) for all work up to plinth level excluding the cost of centering and shuttering complete all as specified and directed. |
| 3 | Providing and fixing Brick work with common burnt clay FPS (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in cement mortar 1 : 6 (1 cement : 6 coarse sand) complete all as specified and directed. |
| 4 | Dismantling old plaster any type, dado or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead complete all as specified and directed. |
| 5 | Material and labour 12 mm cement plaster on brick wall of mix 1 : 6 (1 cement : 6 fine sand) complete all as specified and directed. |
| 6 | Material and labour 15 mm cement plaster on brick wall of mix 1 : 4 (1 cement : 4 fine sand) at height of 10m or more from GL with water proofing compound complete all as specified and directed. |
| 7 | Extra for providing and mixing water proofing material in cement plaster work in proportion min 3% by weight of cement or as recommended by the manufacturers complete all as specified and directed. |
| 8 | M&L for 6 mm thick cement plaster 1:3 (1 cement : 3 fine sand) as in ceiling complete all as specified and directed. |
| 9 | Two or more coat of Distempering including primer in new wall surface with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete all as specified and directed. |
| 10 | M&L for Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm).Note: Item shall be included rate of writing of qtr no in block, roman, italic or indian font complete as per direction by Engr-in-Charge. |
| 11 | M&L 3mm thick wall care putty on wall surface complete all as specified and directed. |
| 12 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, of area 3 sqm and below architrave, holdfasts etc. and making good jambs, cills and soffits complete and stacking within 50 metres lead complete all as specified and directed. |
| 13 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, of area above 3 sqm architrave, holdfasts etc. and making good jambs, cills and soffits complete and stacking within 50 metres lead complete all as specified and directed. |
| 14 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade One or more coats on old work including preparation of surface complete all as specified and directed. |
| 15 | Providing and fixing 100x75x4 mm ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc complete all as specified and directed. |
| 16 | Providing and fixing 125 mm aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc complete all as specified and directed. |
| 17 | Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc complete all as specified and directed. (Copper oxidised as per IS 1378) 250X16 |
| 18 | Providing and fixing Three track three panels sliding window with two glazed & one wire mesh panels with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body factory made uPVC glazed/wire mesh windows/ doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. |
| 19 | Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per design requirements and conforming to IS: 3548 & IS: 16231 shall be paid separately. Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for : (i) Sites with basic wind speed > 45 m/sec as per IS 875 – Part 3 (ii) Sites with structure height more than 20m for all wind speeds Three track three panels sliding window with two glazed & one wire mesh panels with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body.Using R3 series with frame (98 mm & above) x (40 mm & above) & both glazed and fly screen sash (30 mm & above) x (55 mm & above) with zinc alloy (zamak) powder coated handle on every glazed panel along with multi-point locking system. (Height upto 1.8m). complete all as specified and directed. |
| 20 | Providing and fixing float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item). |
| 21 | Fly proof stainless steel grade 304 wire gauge with 0.5 mm dia. wire and 1.4 mm wide aperture with matching beading complete all as specified and directed |
| 22 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. |
| 23 | Providing and laying antiskid 600x600mm Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours\ and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily complete all as specified and directed. |
| 24 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete all as specified and directed. |
| 25 | M&L 25mm thick Cement concrete type B-0,1:2:4 (20mm graded aggregate)in floor finishes complete all as specified and directed |
| 26 | Providing and fixing 18 mm thick Granite stone slab all colour and Granite stone slab of colour black, Cherry/Ruby red area of slab above 0.50 sqm, mirror polished, premoulded and prepolished, machine cut for kitchen platforms,staircase, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1 : 4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish complete all as specified and directed. |
| 27 | Dismantling 15 to 50 mm dia GI pipe including stacking of dismantled pipes (within 50 metres lead) complete all as specified and directed. |
| 28 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes of 15mm dia nominal bore having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & brass threaded fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc complete as per direction of Engineer in Charge. |
| 29 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes of 20mm dia nominal bore having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittingswith one step CPVC solvent cement, trenching, refilling & testing ofjoints complete as per direction of Engineer in Charge. complete as per direction of Engineer in Charge. |
| 30 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes of 50mm dia nominal bore having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittingswith one step CPVC solvent cement, trenching, refilling & testing ofjoints complete as per direction of Engineer in Charge. complete as per direction of Engineer in Charge. |
| 31 | Providing and fixing 50mm gun metal gate valve with C.I. wheel of approved quality (screwed end) complete all as specified and directed. |
| 32 | Providing and fixing in repairs stainless steel A ISI 304 (18/ 8) kitchen sink with drain board 510x1040 mm bowl depth 250 mm as per IS : 13983 with CI brackets and stainless steel plug 40 mm, Flexible (coil shaped) PVC waste pipe 32mm dia with length not less than 700 mm including painting of fittings and brackets, cutting and making good the walls wherever required complete all as specified and directed. |
| 33 | Providing and fixing in repair 15 mm nominal bore with 45 cm length unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour complete all as specified and directed. |
| 34 | Dismantling 100 mm dia CI, PVC or asbestos rain water pipe with fittings and clamps including stacking the material within 50 metres lead complete all as specified and directed. |
| 35 | Dismantling 75 mm dia CI, PVC or asbestos rain water pipe with fittings and clamps including stacking the material within 50 metres lead complete all as specified and directed. |
| 36 | S&F 110mm dia Polypropylene (PP) pipes, mineral-filled, single socketed, any length, having density 1.6 gm/cm³, soundproof with sound rating of 12 dB(A) at 2 lps as per DIN 4109 in association with EN 14366, suitable for all pressureless waste pipes in accordance with DIN EN 12056 and DIN 1986-100, including all bends, oval access door/fittings etc, fixed to walls/ceiling with heavy duty double sided clamp (Shaivi or equivalent) by interval not more than 2.00m complete all as specified and directed by Engineer-in-Charge. |
| 37 | S&F 75mm dia Polypropylene (PP) pipes, mineral-filled, single socketed, any length, having density 1.6 gm/cm³, soundproof with sound rating of 12 dB(A) at 2 lps as per DIN 4109 in association with EN 14366, suitable for all pressureless waste pipes in accordance with DIN EN 12056 and DIN 1986-100, including all bends, oval access door/fittings etc, fixed to walls/ceiling with heavy duty double sided clamp (Shaivi or equivalent) by interval not more than 2.00m complete all as specified and directed by Engineer-in-Charge. |
| 38 | Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprisingof virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ®Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 39 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) |
| 40 | M&L Ventilator Casement window single panel with or without fixed panel with S.S. 304 friction hinges as per size and weight of sash, single point locking zinc alloy (zamak) powder coated handles. Using R1 series with frame (33 mm & above ) x (35 mm & above) & sash /mullion (33 mm & above) x (50 mm & above). (Height upto 0.90 metre) complete all as specified and directed. |
| 41 | Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead acomplete all as specified and directed. |
| 42 | M&L Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre complete all as specified and directed. |
| 43 | M&L Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed. |
| 44 | S&F PVC Designer False Ceiling made of PVC laminated panels 10 mm thick, fire-retardant, ISI marked, with density not less than 1.4 gm/cm³, in approved shade, colour and pattern, with laminate finish (glossy/matte as approved), fixed with screws to existing framework, with all joints aligned, edges neatly finished, including cut-outs for light/fan/AC fittings as required, surfaces cleaned and complete all as specified and directed.Note: GI framework shall be measured and paid for separately). |
| 45 | Supply and fix stainless steel handle oval shape fabricated type anodized 150mm long of approved design, shape and make with ISI mark embosed on it, fixed in repairs with nut screws & washers complete all as specified and as directed. |
| 46 | Supply and fix stainless steel finish soft closing 100mm hinges of approved design, shape and make with ISI mark embosed on it, fixed in repairs with nut screws & washers complete all as specified and as directed. |
| 47 | Providing & fixing White vitreous china water closet Orissa pattern W.C Pan of size 580x440 mm squatting pan (Indian type) along with “S” or “P” trap including dismantling of old WC seat and “S” or “P” trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material including malba, complete all as specified and directed. |
| 48 | Providing and fixing 10 ltr capacity P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete all as specified and directed. |
| 49 | Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :150 mm diameter, complete all as specified and directed by Engr-in-Charge. |
| 50 | S&F in repairs White Vitreous China Wash Down Water Closet (WC) Pan, wall-mounted,including flushing cistern with mild steel Chromium-Plated or aluminised hinging device including soft-closing seat cover, connection to down pipe and flushing pipe, complete all as specified and directed by Engr-in-Charge. Make: Hindware, Cat. Part No.: 92535 (P-18.5) cist-92130 or equivalent |
| 51 | S&F in repairs Health Faucet (ABS body) with mild steel Chromium-Plated finish, suitable for 15 mm dia pipe, including 1.25 m long flexible tube and ABS wall hook, making all necessary connections and fixing in position, complete in all respects as specified, complete all as specified and directed by Engr-in-ChargeMake: Hindware, Cat. Part No.: .F160013CP or equivalent, complete all as specified and directed by Engr-in-Charge. |
| 52 | S&F in repair CP Towel Ring of approved size and design as per enginner in charge complete all as specified and directed. Make: Hindware, Cat. No.: F450024 or equivalent. |
| 53 | S&F in repair CP Soap Dish of approved size and design as per enginner in charge complete all as specified and directed Make: Hindware, Cat. No.: F890002 or equivalent. |
| 54 | Providing and fixing CP Brass 32 mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. complete all as specified and directed. |
| 55 | S&F CP Square Drain Jali 127mm of approved size and design as per enginner in charge complete all as specified and directed. |
| 56 | Providing and fixing in repair 15mm bore C.P. brass angle valve for basin mixer and geyser points etc of approved quality conforming to IS:8931 complete all as specified and directed. |
| 57 | Providing and fixing in repair 15mm bore C.P. brass bib cock of approved quality conforming to IS:8931 complete all as specified and directed. |
| 58 | S&F in repair fancy type two way bib taps with wall flange,chromium plated cast copper alloy with crutch or butterfly handle,screwed down,screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.Make: Hindware, Cat. No.: F650005 or equivalent |
| 59 | S&F in repair LED Mirror, vertical type, size 800×600 mm, including all necessary fittings, mounting accessories, connections, and fixing in position, Make: Hindware or equivalent, complete all as specified and directed by Engr-in-Charge. |
| 60 | Providing and fixing in repair 15mm bore C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931., complete all as specified and directed by Engr-in-Charge. |
| 61 | S&F in repairs Vitreous China Counter Top Wash Hand Basin (WHB), Snow White, fancy type, overall size 490×400×150 mm, including 32 mm CP Pop-Up Waste Coupling (Full Cap ceramic) CP Bottle Trap (32 mm) with 225 mm & 175 mm long wall connection pipes, wall flange (Premium), 300 mm long PVC connection pipe, and all necessary fittings and accessories,complete all as specified and directed by Engr-in-Charge. Make: Hindware, Cat. No.: 10095 or equivalent |
| 62 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required One urinal basin with 5 litre white P.V.C. automatic flushing cistern complete all as specified and directed |
| 63 | M&L in repairs 12mm thick toughened moduler glass partitaion as in railing, staircase including seamless frosted glass fixing at powder coated aluminium/SS-304 corner frame/bracket work for glass, seal by silicon sealent complete all as specified and directed. |
| 64 | S&F in repairs Pillar taps but fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed by Engr-in-Charge. |
| 65 | Taking up/down plants or vegetation growth from wall upto roof level by means of cutting hole into brick wall and making good the surface of dismantled portion (not exc 150 sq cm superfical area and not exc one brick depth) using brick bats /aggregate and plastering in cement mortar (1:4) to distrubed portion and applying two coats of cement base paint / weather coat to match the existing surface upto forth floor complete all as directed by Engineer -incharge. |
| 66 | M&L for applying siloxane based water repellent impregnation on concrete/brick/stone/masonry surfaces, complete all as specified and directed, including the following:-(a) Preparation of surfaces by cleaning and removing dust, dirt, oil, grease, efflorescence, mould etc, using brush/roller/spray with detergent, degreaser, light blast cleaning, steam cleaning as required, including removal of any existing incompatible coating/paint which may block absorption.(b) Filling/repairing cracks wider than 200 microns using approved crack filler as per manufacturer’s instructions.(c) Ensuring surface is dry (maximum moisture content 5–6%) with no visible damp patches before application. Applying the first coat by low-pressure spray, roller or brush in vertical direction.(d) Applying second coat before the first coat is fully dried, strictly as per manufacturer’s instructions.Coverage rate: 0.30 to 0.50 Kg/Sqm per coat (corresponding to 0.375 to 0.625 L/Sqm per coat).Notes:(i) The work shall be carried out strictly under manufacturer’s directions and/or by an authorised applicator.(ii) Contractor shall produce manufacturer’s certificate after satisfactory completion of work. |
| 67 | Dismantling water tanks and removing to store capacity exc. 250 ltr but not exceedings 500 liters complete all as specified and directed. |
| 68 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank complete all as specified and directed. |
| 69 | Dismantling steel work manually/ by mechanical means in built up sections without dismembering and stacking within 50 metres lead complete all as specified and directed. |
| 70 | Providing and fixing Steel work In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required complete all as specified and directed. |
| 71 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:4:8 or leaner mix (including equivalent design mix) |
| 72 | S&F acrylic cabin/room name plate, fabricated from 8 mm thick acrylic sheet, with double-side lettering in Hindi or English, of size as required by the user and as directed by the Engr-in-Charge, complete all as specified and directed. |
| 73 | Supply and fix of 18mm thick marine plywood (BWP) as per IS 710, laminated both sided of any colour of sunmica sheet of 0.9 mm thick for kitchen cabinets etc including edge banding / lipping of matching strips as approved by Engineer-in-Charge, all edges and corners finished neatly and complete all specified and as directed. |
| 74 | Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc. by applying cement slurry mixed with water proofing cement compound consisting of applying :(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours.(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.Note:The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. |
| 75 | Taking down of carefully unserviceable Aluminium/copper point wiring (light, fan socket or power) complete with fitting such as switches, ceiling rose lamp holder, sockets, fan regulators, SK/FTL light fittings etc removing materials for store for keeping in safe custody or for taking credit (credit for above items should be taken as per conditions separately) and making good disturbed surfaces of walls, floors etc complete all as specified and directed. |
| 76 | M&L for point wiring with single core PVC insulated unsheathed 1100 volt grade FRLS-IS 694 cable with multi stranded copper conductor of size 1.5 Sq mm (Nominal area) drawn through and including non metallic rigid PVC conduit medium duty ISI marked not less than 20mm dia, concealed conduit wiring in walls and surface with GI saddles GI screws, rawal plugs in ceiling or roof if not possible including Tee, Junction boxes and provision of flush metal boxes, inner and outer plate suitable for modular switch, socket and fan regulator as per site requirement and drawing continuous earth wire with and including PVC insulated unsheathed 1100 Volts grade FRLS-IS 694 cable with multi stranded copper conductor of size 1.5 Sq mm (Nominal area) and connected to main earth dolly complete all as specified and directed for one light/Fan point controlled by one Switch. |
| 77 | Description all as per Srl item No. 75.00 here in before but for point wiring for 5 pin switch socket outlet, 5/6 Amps on same board with other switches complete all as specified and directed. |
| 78 | Description all as per Srl item No. 75.00 here in before but for point wiring for 5 pin switch socket outlet, 5/6 Amps on independent board complete all as specified and directed. |
| 79 | All as per item No 76 above for one power point 3 pin 15 Amps socket outlet PVC insulated unsheathed 1100 volt grade cable with stranded copper conductor of size 2.5 Sq mm (Nominal area) including earth wire PVC insulated unsheathed 1100 volt grade cable with stranded copper conductor of size 2.5 Sq mm (Nominal area)cable common connected to earth dolly, all as specified for one 3 pin 15 amps socket outlet point controlled by one switch complete all as specified and directed. |
| 80 | Description all as per Srl item No. 75.00 here in before but for one power point 3 pin 15 Amps socket out let PVC insulated unsheathed 1100 volt grade cable with stranded copper conductor of size 4 Sq mm (Nominal area) including earth wire PVC insulated unsheathed 1100 volt grade cable with stranded copper conductor of size 4 Sq mm (Nominal area)cable common connected to earth dolly, all as specified for one 3 pin 15 amps socket outlet point controlled by one switch complete all as specified and directed. Please Enable Macros to View BoQ information |
| 81 | Description all as per Srl item No. 75.00 here in before but for one power point 3 pin 15 Amps socket out let PVC insulated unsheathed 1100 volt grade cable with stranded copper conductor of size 4 Sq mm (Nominal area) including earth wire PVC insulated unsheathed 1100 volt grade cable with stranded copper conductor of size 4 Sq mm (Nominal area)cable common connected to earth dolly, all as specified for one 3 pin 15 amps socket outlet point controlled by one switch complete all as specified and directed. Please Enable Macros to View BoQ information |
