|
| 1 | Item No. 1.1 Providing and fixing in position Different size of Table (Height 750MM) made out of 19 min thick marine plywood of the requisite manufacture ie. Anchor/Century/Kenwood/Greenply or equivalant generally confirming to IS 710-1980 for Top, vertical side and 6 mm & 12 mm thick marine plywood for back and drawer with necessary BTC wood lipping and moulding. the External shall be finished with 3.5 to 4mm thick Greenply Veneer (Wood Crrests) sheet Excluding melamine polish and internal shall be finished laminate 0.80 mm thick (Royale touche) with three years guarantee on requisite stamp paper etc.Executive table 3000x750MM Left pedestal under main table (left end)of size 600 x 750 x 750 mm in 19 mmBWP plywood with 3 drawers (front heights 100/150/275 mm), drawer sides in 12 mm ply and bottoms in 9 mm ply, mounted on 450 mm long, 45 kg telescopic slides with central lock, brass handles and leveling feet, using hardware of approved make Ozone / Hettich /Hafele or equivalent,Central keyboard tray of size 700 x 300 x 25 mm in BWP plywood with laminate finish, provided as pull-out on 500 mm telescopic slides, tilt/swivel adjustable to working height 650–750 mm, with mouse wing, C‑clamp mount and all accessories, complete.Right side table of size 750 x 500 x 750 mm in 19 mm BWP plywood, all exposed edges with 2 mm PVC edge band, complete. Side table to have 3 drawers in the top portion on telescopic slides with central lock and handles .The item shall be measured in Sq.m. of (Exe. table) Front area &(Conf.table) Top Area ,as per attached 3D Imgae & as per direction of engineering incharge etc complete.(Non SSR) |
| 2 | Item No. 1.2A - Proving and fixing 6 mm corian solid surface on table top with corian adhesives LG and Dupend fixing it jointless with smooth edge polish complete with necessary hardwear as directed by Engineer in change.(Non SSR) |
| 3 | Item No. 1.2B - Providing and fixing Executive Table of approved size of Height 750 mm made of 18 mm thick ISI marked 710 Marine plywood for vertical supports & top & 12 mm thick ISI marked 710 Marine ply wood extra for design with 25 x 12 mm teak wood moulding at edges and front finished with Melamine polish and Providing 1 mm thick texture laminate on all exposed & internal surfaces & 12 mm glass on top, keyboard drawer is made by using 12 mm thick Marine ply ISI 710 and telescopic channels on side and small storage below it & internal surfaces of drawer & storage finished with French polish with brass hinges, screws, brass handles, locks as per detailed drawing and with all necessary fittings, fixtures, fasteners, fevicol and nails etc.Left pedestal under table (left end) of size 0.40 m(L) x 0.45 m (W) x 0.65 m (H) consist of one drawer and two selves with openable shutter, and side unit for table of size 0.75 m (L) x 0.450 m (W) x 0.75 m (H) consist of top portion two drawer and below portion with two compartment of two selves with openable shutter. as directed by the Engineer in charge etc.Complete(Non SSR) |
| 4 | Item No. 1.2C - Providing & fixing Staff / Computer table having Height 750 mm using 18 mm thick Marine ply ISI 710 for top & vertical supports, keyboard drawer is made by using 12 mm thick Marine ply ISI 710 and telescopic channels on side and small storage below it, external surface is to be finished with 1 mm thick laminate with 6 mm horizontal groove including 25 x 12mm lipping finished with Melamine polish & internal surfaces finished with French polish with brass hinges, screws, brass handles, locks as per detailed drawing and with all necessary fittings, fixtures, fasteners, fevicol and nails etc. Left pedestal under table (left end) of size 0.40 m(L) x 0.45 m (W) x 0.65 m (H) consist of one drawer and two selves with openable shutter etc as directed by engineer incharge Complete.(Non SSR) |
| 5 | Item No. 1.2D - Providing and fixing meeting table Height 750 MM of approved size(4000 x1400MM) made of 18 mm thick marine plywood i.e. Anchor/Century/Kenwood/Greenply or equivalant generally confirming to ISI 710 for vertical supports and top 55mm thick and 12 mm thick for front with T.W. 50 x 12 mm moulding at edge and front finished, with Melamine polish. providing 1 mm thick texture laminate on all exposed surface & internal surface finished with French polish as per detailed drawing with screws, fevicol and nails etc.The item shall be measured in Sq.m. of Top area as Directed by Engineer-in-charge etc Complete.(Non SSR) |
| 6 | Item No. 1.2E - Providing and fixing 53 cm deep Cupboard type Storage Unit made out of 19mm thick plywood of the requisite manufacture confirming to I.S. 710-1980 for fraunes, internal verticals horizontal divisions, shutters and 6mm & 12mm thick marine plywood for drawers with necessary locks, handles, hardware, lipping & beading patti (BTC) ete. The total shall be finished with formica laminate Sheet from inside, outside in approved pattem with grooves etc. with three years guarantee bond on requisite stamp paper including all leads & lifts etc, features four adjustable shelves of 19mm thick IS710BWP marine plywood, supported by metal pins at 150 mm intervals, shutters mounted on heavy-duty concealed hinges (approved brands: Dorma, Hafele,Hidrolik or Hettich )with premium wave key locks The item shall be measured in Sq.m. of front area and make as per attached 3D Images . As directed by engineer in charge etc completed(Non SSR) |
| 7 | Item No. 1.2F - Providing & fixing on site 40 centimeter deep low height storage unit made out of 19 milimeter thick Marine Plywood of the requisite manufacture viz Anchor- /Century/Kenwood/ Duro or equivalent generally confirming to I.S. 303/I.S. 710-1980 frame and internal verticals, 6 milimeter thick Marine Ply of the requisite manufacture viz Anchor / / Century / Kenwood / Duro or equivalent generally confirming to IS. 303 /I.S. 710-1980 back, horizontal divisions, openable shutters with necessary locks, handles, hardware, lipping (Burmah Teak Wood) etc. The unit shall be Total finished with formica laminate sheet from inside, outside in approved pattern with grooves etc. with three years gaurantee bond etc. including all leads & lifts etc complete. Consisting of Top Portion with drawer unite(s), Lower Portion with openable shelves fitted with shutters. The item shall be measured in Sq.m. of front area and make as per attached 3D Images . As directed by engineer in charge etc completed (Non SSR) |
| 8 | Item No. 1.2G - Providing & fixing 75 mm thick Partition with Laminate & Glass finished using 18 mm thick Marine ply ISI marked 710 with anti termite for frame work fixed to wall, floor & slab with 50 x50 mm 2nd class T.W. vertical post & horizontal supports which covered with 12 mm thick Marine ply ISI marked 710 on both side & finished with 1 mm thick laminate from both side including 12 mm thick frosted glass and T.W. lipping Patti of size 32 x 12 mm thick on both side of glass and where necessary on top finished with Melamine as per design and finished with all necessary fittings, fixtures, fasteners, fevicol and nails etc. As directed by Engineer incharge Complete.(Non SSR) |
| 9 | Item No. 1.3A - Providing and fixing Wall panelling with Fluted Panels using 18 mm thick waterproof marine ply BWR grade complying with IS:710 for vertical supports of size 150 mm x 45 mm and covered with 12 mm thick waterproof marine ply BWR grade complying with IS:710 and external side to be finished with Fluted Panels with wooden beading grove and completed as per detail drawings and as directed by the Engineer in charge etc. Complete(Non SSR) |
| 10 | Item No. 1.3B - Single Bed :- Providing and supplying for Single Bed of Size 2025 LX 1000DX 650H The bed unit is made up of 18mm thick Ply with both side decorative laminate. All exposed edges are sealed with 2mm thick PVC edge Banding. All exposed edges are sealed with 2mm thick PVC edge Banding, Fitted necessary hardware etc.with the outer frame constructed from 19 mm thick BWP (Boiling Water Proof) marine plywood conforming to IS 710 standards from approved brands Green Ply, Century, or Anchor; the frame features a 38 mm thickness and 200 mm height for the perimeter structure, including headboard and footboard panels. as directed by the Engineer in charge etc. Complete (Non SSR) |
| 11 | Item No. 1.4A - King Size Bed : P/F Box Type Bed having 45cm height made out of 19mm and 12mm thick marine plywood of requisite manufacture i.e. Anchor/Century/Kenwood/Duro/ Jet or equivalant generally confirming to I.S.710-1980 for all sides and shelf including necessary B.T.C. frame work of 38 x 200 mm finished with formica laminate sheet of approved make and pattern with necessary fixtures & fastening, with three years guarantee on requisite stamp paper french polishing from inside and melamine polish to BTC moulding lipping patties including all lead & lifts and as per attached drawing and instructions of Engineer-in-charge etc. complete.(Non SSR) |
| 12 | Item No. 1.4B - Providing and Supplying M.S.Powder coated bunk bed two layers size 1x1.88 x 0.8 high 1.85 cm with proper ladder m.s. square pipe of size 50 mm × 50 mm × 1.6 mm thick and m.s. round pipe 25mm øx 2 mm thick with powder coated etc. of approved gauge(2mm), including sleeping platforms with M.S. slats/perforated sheet/mesh base, integrated ladder with anti-slip steps,and safety guard rails 25 mm × 25 mm × 1.2 mm on upper bunk, complete with all welding, grinding, edge rounding, necessary fittings, end caps and supports, finished with pre-treatment (degreasing, rust removal, phosphating) and epoxy polyester powder coating of approved shade (minimum 60–80 microns thickness), including all materials, labour, transportation, and installation at site, complete in all respects as directed by the Engineer in charge etc.Complete.(Non SSR) |
| 13 | Item No. 1.4C - Providing and fixing three (3.00) mm thick P.V.C. acoustic flooring in strip from with latest timber 0.07mm wear layer in approved plank range. It should be confirming to IS 3462 P.V.C. flooring Anti Static type. Persting on smooth and level surface complete as directed including all materials, pesting solution of approved manufacture. The size type and shade of the tiles shall be specified and/or as directed by the Engineer( Non SSR) |
| 14 | Item No. 1.4D - Dinning Table 8 Seater :Dinning Table 8 Seater : Providing and fixing Dinning Table 8 Seater of Size 2400 L X 1200 W X 750 H with Solid Wood (Sag) Bottom and chair with Cushion consist of top made out of 19mm thick BWP(IS710) Grade Plywood of requisite manufacture i.e Anchor /Century /Green plyasper approved Table Legs and Bottom support made out of Commercial teakwood Exterior Top finish with1mm thlk outer laminate of Green lam,Century, Anchor or equivalent polish for wood sample should get approved before instalation or as directed by Engineer In charge etc complete.(NON SSR). |
| 15 | Item No. 1.4E - KITCHEN CABINET UNIT : Providing and supplying of Storage Cabinet 2700 x 450 x 2000 mm all panels are made in 18 mm ply with both side selected color laminate. Shutter will be on soft close(hydrolic) hinges. cabinet inner side adj. and fix shelf as per box file height. all edge 22 x 2 mm match edge banding. feeted with necessary hardware. as per given drawing. with shelves and partitions in 18 mm plywood and 6 mm plywood for back panels, including curved/straight units as per design, complete with laminate/veneer finish of approved make and shade on external surfaces and laminate/polish on internal surfaces, all exposed edges finished with PVC edge banding/wooden lipping, including SS/MS hinges (soft-close), telescopic drawer channels, handles, locks, baskets, pull-outs and other modular fittings, complete with glass shutters/shelves with LED lighting (if specified), and including necessary hardware, fixtures, fasteners, sealants, cutting, joinery and installation, finished in all respects including transportation, leads & lifts, as per drawings and instructions of Engineer-in-charge.(NON SSR) |
| 16 | Item No. 1.4F - Pantry Unit :- Providing and supplying for Pantry Unit of size 3900 W X 600 D X 2100 H in mm. Using Commercial plywood with HGL and SF laminate. Table top 36mm thick. HGL laminate, edge cover by 1.3 x 45mm PVC edge binding with PUR glue. Gable end 36mm thick. HGL laminate, edge cover by 2 x 45mm PVC edge binding with PUR glue. modesty panel 18mm thick. having both side SF laminate, edge cover by 0.8 x 22mm PVC edge binding with PUR glue. Provided 2 drawer fix pedestal with telescopic slide, locks and handles. Provided 6mm thick. clear glass on table top. Fitted necessary hardware etc.(NON SSR) |
| 17 | Item No. 1.4G - Providing & Fixing Invisible Grill made up of frame by Aluminium Track 3\\" Spacing For Invisible Grill in Bottom And Top Placing Of SS Wire Ropes for holding J3 mm S.S. 316 grade non magnetic nylon coated wire fixed vertically at 75 mm center to center distance and two rows horizontally. 3 mm S.S. stifliner is fixed at every Horizontal and Vertical Junction Point for and 3 mm aluminium copper ferrul used for start & end point of ss. wire and every eye hook, Plastic Side Insert for tracks, GI Screw Hex head with plug for ss. wire locking purpose as per drawing attached. (Excluding External Scaffolding) (NON SSR) |
| 18 | Item No. 1.4H - Providing and fixing Name Plate of size 0.30 m x 0.20 m made up alluminium composit sheet with name etc lettering work in radium of approved colour and shape with drilling, screws necessary fittings etc. Complete. (NON SSR) |
| 19 | Item No. 1.5 - Providing & Arrangemnt of MId Back, Normal Syncro Mechanism, Fixed Armrest, Gaslift for Seat height adjustment, Standard 5-prong/Nylon Base with Leather Upholstery (Item No. 51.42) |
| 20 | Item No. 1.6 - Providing & Arrangemnt of High Back Chair-TILT MECHANISM WITH MULTILOCKING, HIGH DENSITY CUSHION ON SEAT COMPOSITE LEATHER WITH METALLIC SILVER FINISH BASE AND ARMS WITH P.U.CASTORS GASLIFT FOR HEIGHT ADJUSTMENT. (Item No. 51.41) |
| 21 | Item No. 1.7 - Public Seating Chair.-3 Seater Providing and Fixing 3 seater Public seating chair made of complete metal with Legs in Crome finish and seates in silver powder coating finish. (Item No. 51.44) |
| 22 | Item No. 1.8 - Nilkamal Plastic Chair(Mumbai DSR) (Item No. 108.12) |
| 23 | Item No. 1.9 - 3 Seater Sofa : Providing & Supplying Three seater sofa of overall size 1950x760x825 mm ht. made out of 75x38mm (finished size ) with CCTW section frame 6mm marine plywood generally confirming to I.S.303/I.S. 710-1980 for necessary covering from back & arm rests. The seat shall be 100mm thick branded quality foam covered 1\\" soft foam and arms having CCTW 50mm thick 50 density branded foam covered 1\\" plain soft foam. All work covered with tapestry fabric upto Rs.400/- per Sq.M.including necessary hardware, naver, jute cloth.Casement, springs or belted absorber etc. complete. All exposed wooden surface shall be melamine polished and antitermite treatment to plywood and wood work with five years guarantee bond etc. including all leads & lifts etc. complete as per Architect's Drawing & instruction of Engineer-in-charge.(Mumbai DSR) (Item No. 102.08) |
| 24 | Item No. 1.10 - 2 Seater Sofa : Providing & Supplying two seater sofa of overall size 1350x760x825 mm ht. made out of 75x38mm (finished size ) with CCTW section frame 6mm commercial plywood generally confirming to I.S.303/I.S. 710-1980 for necessary covering from back &arm rests. The seat shall be 100mm thick Dunlop or MM or equivalent brand quality foam covered 1\\" soft foam and arms having CCTW 50mm thick 50 density branded foam covered 1\\" plain soft foam. All work covered with tapestry fabric upto Rs.400/- per Sq.M.including necessary hardware, naver, jute cloth.Casement, springs or belted absorber etc. complete. All exposed wooden surface shall be melamine polished and antitermite treatment to plywood and wood work with five years guarantee bond etc. including all leads & lifts etc. complete as per Architect's Drawing & instruction of Engineer-in- charge.(Mumbai DSR) (Item No. 102.09) |
| 25 | Item No. 1.11 - Tea Table 900mm X 750mm X 450mm form.s. ante chamber Providing And Fixing Of Tea Table 900mm X 750mm X 450mm With 12mm Thick Colour Eitched Tempered Glass With Bevelled Drawing Made Out Of 18mm Thick Waterproofing Ply. The Outer Laces To Be Finished With High Quality 4 Mm Thik Veneer Or 1 Mm Thik Mica Etc. (Item No. 51.54) |
| 26 | Item No. 1.12 - Double Faced Mobile Unit for Compactor 2150mmH x 2745mmW x 900mmD Providing and fixing Double Faced Mobile Unit for Compactor 2150mmH x 2745mmW x 900mmD-BASE FRAME : Base Frame shall be fabricated in channel Type from minimum 2.5mm thick MS Sheet Size of Channel 25mm x 100mm x 45mm. GUIDE RAILS : The guide rails shall be made out of 28mm Bright bar placed on 1.2mm thick M.S. Plate which will be above the floor and are as per the international standard of safety. SUPER STRUCTURE : Super structure of the Mobile storage system will consist of knock down type panels. All the components such as shelves, front panel, end panel, vertical rear panel, central partition etc. Will act as an integral member of the Unit. SHELVES : Shelves made of 22SWG thick Prime Quality C.R.C.A. having 10 folds each will be provided each designed to carry a U.D.L. of 70 Kilograms. VERTICAL PANEL : Vertical panel consists of the front, Centre & rear panel shall be made out of 20SWG thick C.R.C.A. Prime quality Mild Steel & designed to take the load of shelves. DRIVE COVER PANEL : Made out of 22SWG thick C. R.C. A. prime quality Steel to cover the entire drive mechanism. CENTRE PARTITION : The Centre partition will comprise of a full C.R.C.A. prime quality Mild Steel 22SWG Sheet. LOCKING : System will be provided with individual rack locking as well as centralised locking arrangement on the last unit when all units are brought together, central lock when operated gets locked with the floor & does not allow access to the units. DRIVE MECHANISM : Driving Mechanism will be provided externally supported on special grade anti-friction bearing to have smooth & effortless movement. Entire mechanism or gear & sprockets shall be incorporated within the front panel provided in the front of the unit within an area of 1000mm x 200mm x 60mm. DRIVING WHEEL : Fully Powder Coated three pronged drive wheel for better torque & free movement of the rack over the guide rail. INDEXING ARRANGEMENT : Acrylic card holders provided on the front panel for easy identification & retrieval. FINAL FINISH : Powder Coating(8 tanks process with 70 microns). (Item No. 51.45) |
| 27 | Item No. 1.13 - Single Faced Mobile Unit for Compactor 2150mmH x 2745mmW x 457mmD Providing and fixing Single Faced Mobile Unit for Compactor 2150mmH x 2745mmW x 457mmD-BASE FRAME : Base Frame shall be fabricated in channel Type from minimum 2.5mm thick MS Sheet Size of Channel 25mm x 100mm x 45mm. GUIDE RAILS : The guide rails shall be made out of 28mm Bright bar placed on 1.2mm thick M.S. Plate which will be above the floor and are as per the international standard of safety. SUPER STRUCTURE : Super structure of the Mobile storage system will consist of knock down type panels. All the components such as shelves, front panel, end panel, vertical rear panel, central partition etc. Will act as an integral member of the Unit. SHELVES : Shelves made of 22SWG thick Prime Quality C.R.C.A. having 10 folds each will be provided each designed to carry a U.D.L. of 70 Kilograms. VERTICAL PANEL : Vertical panel consists of the front, Centre & rear panel shall be made out of 20SWG thick C.R.C.A. Prime quality Mild Steel & designed to take the load of shelves. DRIVE COVER PANEL : Made out of 22SWG thick C. R.C. A. prime quality Steel to cover the entire drive mechanism. CENTRE PARTITION : The Centre partition will comprise of a full C.R.C.A. prime quality Mild Steel 22SWG Sheet. LOCKING : System will be provided with individual rack locking as well as centralised locking arrangement on the last unit when all units are brought together, central lock when operated gets locked with the floor & does not allow access to the units. DRIVE MECHANISM : Driving Mechanism will be provided externally supported on special grade anti-friction bearing to have smooth & effortless movement. Entire mechanism or gear & sprockets shall be incorporated within the front panel provided in the front of the unit within an area of 1000mm x 200mm x 60mm. DRIVING WHEEL : Fully Powder Coated three pronged drive wheel for better torque & free movement of the rack over the guide rail. INDEXING ARRANGEMENT : Acrylic card holders provided on the front panel for easy identification & retrieval. FINAL FINISH : Powder Coating(8 tanks process with 70 microns). (Item No. 51.46) |
| 28 | Item No. 1.14 - Single Faced Fixed Unit for Compactor 2150mmH x 2745mmW x 457mmD Providing and fixing Single Faced Fixed Unit for Compactor 2150mmH x 2745mmW x 457mmD-BASE FRAME : Base Frame shall be fabricated in channel Type from minimum 2.5mm thick MS Sheet Size of Channel 25mm x 100mm x 45mm. GUIDE RAILS : The guide rails shall be made out of 28mm Bright bar placed on 1.2mm thick M.S. Plate which will be above the floor and are as per the international standard of safety. SUPER STRUCTURE : Super structure of the Mobile storage system will consist of knock down type panels. All the components such as shelves, front panel, end panel, vertical rear panel, central partition etc. Will act as an integral member of the Unit. SHELVES : Shelves made of 22SWG thick Prime Quality C.R.C.A. having 10 folds each will be provided each designed to carry a U.D.L. of 70 Kilograms. VERTICAL PANEL : Vertical panel consists of the front, Centre & rear panel shall be made out of 20SWG thick C.R.C.A. Prime quality Mild Steel & designed to take the load of shelves. DRIVE COVER PANEL : Made out of 22SWG thick C. R.C. A. prime quality Steel to cover the entire drive mechanism. CENTRE PARTITION : The Centre partition will comprise of a full C.R.C.A. prime quality Mild Steel 22SWG Sheet. LOCKING : System will be provided with individual rack locking as well as centralised locking arrangement on the last unit when all units are brought together, central lock when operated gets locked with the floor & does not allow access to the units. DRIVE MECHANISM : Driving Mechanism will be provided externally supported on special grade anti-friction bearing to have smooth & effortless movement. Entire mechanism or gear & sprockets shall be incorporated within the front panel provided in the front of the unit within an area of 1000mm x 200mm x 60mm. DRIVING WHEEL : Fully Powder Coated three pronged drive wheel for better torque & free movement of the rack over the guide rail. INDEXING ARRANGEMENT : Acrylic card holders provided on the front panel for easy identification & retrieval. FINAL FINISH : Powder Coating(8 tanks process with 70 microns). (Item No. 51.47) |
| 29 | Item No. 1.15 - Double Faced Mobile Unit for Compactor 2150mmH x 1830mmW x 900mmD Providing and fixing Double Faced Mobile Unit for Compactor 2150mmH x 1830mmW x 900mmD-BASE FRAME : Base Frame shall be fabricated in channel Type from minimum 2.5mm thick MS Sheet Size of Channel 25mm x 100mm x 45mm. GUIDE RAILS : The guide rails shall be made out of 28mm Bright bar placed on 1.2mm thick M.S. Plate which will be above the floor and are as per the international standard of safety. SUPER STRUCTURE : Super structure of the Mobile storage system will consist of knock down type panels. All the components such as shelves, front panel, end panel, vertical rear panel, central partition etc. Will act as an integral member of the Unit. SHELVES : Shelves made of 22SWG thick Prime Quality C.R.C.A. having 10 folds each will be provided each designed to carry a U.D.L. of 70 Kilograms. VERTICAL PANEL : Vertical panel consists of the front, Centre & rear panel shall be made out of 20SWG thick C.R.C.A. Prime quality Mild Steel & designed to take the load of shelves. DRIVE COVER PANEL : Made out of 22SWG thick C. R.C. A. prime quality Steel to cover the entire drive mechanism. CENTRE PARTITION : The Centre partition will comprise of a full C.R.C.A. prime quality Mild Steel 22SWG Sheet. LOCKING : System will be provided with individual rack locking as well as centralised locking arrangement on the last unit when all units are brought together, central lock when operated gets locked with the floor & does not allow access to the units. DRIVE MECHANISM : Driving Mechanism will be provided externally supported on special grade anti-friction bearing to have smooth & effortless movement. Entire mechanism or gear & sprockets shall be incorporated within the front panel provided in the front of the unit within an area of 1000mm x 200mm x 60mm. DRIVING WHEEL : Fully Powder Coated three pronged drive wheel for better torque & free movement of the rack over the guide rail. INDEXING ARRANGEMENT : Acrylic card holders provided on the front panel for easy identification & retrieval. FINAL FINISH : Powder Coating(8 tanks process with 70 microns). (Item No. 51.48) |
| 30 | Item No. 1.16 - Single Faced Mobile Unit for Compactor 2150mmH x 1830mmW x 457mmD Providing and fixing Single Faced Mobile Unit for Compactor 2150mmH x 1830mmW x 457mmD-BASE FRAME : Base Frame shall be fabricated in channel Type from minimum 2.5mm thick MS Sheet Size of Channel 25mm x 100mm x 45mm. GUIDE RAILS : The guide rails shall be made out of 28mm Bright bar placed on 1.2mm thick M.S. Plate which will be above the floor and are as per the international standard of safety. SUPER STRUCTURE : Super structure of the Mobile storage system will consist of knock down type panels. All the components such as shelves, front panel, end panel, vertical rear panel, central partition etc. Will act as an integral member of the Unit. SHELVES : Shelves made of 22SWG thick Prime Quality C.R.C.A. having 10 folds each will be provided each designed to carry a U.D.L. of 70 Kilograms. VERTICAL PANEL : Vertical panel consists of the front, Centre & rear panel shall be made out of 20SWG thick C.R.C.A. Prime quality Mild Steel & designed to take the load of shelves. DRIVE COVER PANEL : Made out of 22SWG thick C. R.C. A. prime quality Steel to cover the entire drive mechanism. CENTRE PARTITION : The Centre partition will comprise of a full C.R.C.A. prime quality Mild Steel 22SWG Sheet. LOCKING : System will be provided with individual rack locking as well as centralised locking arrangement on the last unit when all units are brought together, central lock when operated gets locked with the floor & does not allow access to the units. DRIVE MECHANISM : Driving Mechanism will be provided externally supported on special grade anti-friction bearing to have smooth & effortless movement. Entire mechanism or gear & sprockets shall be incorporated within the front panel provided in the front of the unit within an area of 1000mm x 200mm x 60mm. DRIVING WHEEL : Fully Powder Coated three pronged drive wheel for better torque & free movement of the rack over the guide rail. INDEXING ARRANGEMENT : Acrylic card holders provided on the front panel for easy identification & retrieval. FINAL FINISH : Powder Coating(8 tanks process with 70 microns). (Item No. 51.49) |
| 31 | Item No. 1.17 - Single Faced Fixed Unit for Compactor 2150mmH x 1830mmW x 457mmD Providing and fixing Single Faced Fixed Unit for Compactor 2150mmH x 1830mmW x 457mmD-BASE FRAME : Base Frame shall be fabricated in channel Type from minimum 2.5mm thick MS Sheet Size of Channel 25mm x 100mm x 45mm. GUIDE RAILS : The guide rails shall be made out of 28mm Bright bar placed on 1.2mm thick M.S. Plate which will be above the floor and are as per the international standard of safety. SUPER STRUCTURE : Super structure of the Mobile storage system will consist of knock down type panels. All the components such as shelves, front panel, end panel, vertical rear panel, central partition etc. Will act as an integral member of the Unit. SHELVES : Shelves made of 22SWG thick Prime Quality C.R.C.A. having 10 folds each will be provided each designed to carry a U.D.L. of 70 Kilograms. VERTICAL PANEL : Vertical panel consists of the front, Centre & rear panel shall be made out of 20SWG thick C.R.C.A. Prime quality Mild Steel & designed to take the load of shelves. DRIVE COVER PANEL : Made out of 22SWG thick C. R.C. A. prime quality Steel to cover the entire drive mechanism. CENTRE PARTITION : The Centre partition will comprise of a full C.R.C.A. prime quality Mild Steel 22SWG Sheet. LOCKING : System will be provided with individual rack locking as well as centralised locking arrangement on the last unit when all units are brought together, central lock when operated gets locked with the floor & does not allow access to the units. DRIVE MECHANISM : Driving Mechanism will be provided externally supported on special grade anti-friction bearing to have smooth & effortless movement. Entire mechanism or gear & sprockets shall be incorporated within the front panel provided in the front of the unit within an area of 1000mm x 200mm x 60mm. DRIVING WHEEL : Fully Powder Coated three pronged drive wheel for better torque & free movement of the rack over the guide rail. INDEXING ARRANGEMENT : Acrylic card holders provided on the front panel for easy identification & retrieval. FINAL FINISH : Powder Coating(8 tanks process with 70 microns). (Item No. 51.50) |
| 32 | Item No. 1.18 - Bed Side Table @ 400LX 400DX 415H Providing and Fixing Bed Side Table of size 400LX 400DX 415H The bed side unit is made up of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2mm thick PVC edge Banding. The bed side table has one drawer and one shelf. The shelf is made of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2mm thick PVC edge Banding (Item No. 51.58) |
| 33 | Item No. 1.19 - Coir Mattresses 6\\" thick 1\\" MM foam & 5\\" HR foam, 8\\" thick - 2\\" MM foam & 6\\" HR foam, Removable zipper cover for easy maintenance VOC & hazard free MM foam(Mumbai DSR) (Item No. 112.06) |
| 34 | Item No. 1.20 - Colour Double Bed sheets (88\\" x 98'') (Bombay Deying) 2 Pillow cover included with all the Bed sheet & pillow covers embossed as MLA Hostel Mumbai 2019(Mumbai DSR) (Item No. 112.07) |
| 35 | Item No. 1.21 - Colour Single Bed Sheets (60'' x 90'') (Bombay Deying) 2 Pillow cover included with all the Bed sheet & pillow covers embossed as MLA Hostel Mumbai 2019(Mumbai DSR) (Item No. 112.08) |
| 36 | Item No. 1.22 - Pillows (15'' x 24'') 1.50 Kg. cotton with cloth and labour transportation charges (including stitching charges labour charges of Engineer in charge)(Mumbai DSR) (Item No. 112.25) |
| 37 | Item No. 1.23 - Blanket Woolen Single Dimensions 90 x 60 in (228.6 x 152.4 cm) Weight 2400 g (Mumbai DSR) (Item No. 112.02) |
| 38 | Item No. 1.24 - Wardrobe with Mirror @ 900LX 600DX 1965H Providing and Fixing Wardrobe with Mirror of size 900LX 600DX 1965H The wardrobe side panels and doors are made up of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2mm thick PVC edge Banding. The shelves are made of 18mm thick Prelam Particle Board with decorative laminate on both sides. The top is made of 36mm prelam particle board with decorative laminate on both sides.(18mm Prelam Particle board and 18mm batons on all sides to achieve 36mm overall thickness). The exposed edges of the top are sealed with 2mm thick PVC edge Banding. The top most part of the wardrobe has an aluminum hanger rod of EBCO make. One drawer of size 400(W) x 150(H) x 450(D) made of 18mm thick prelam Particle Board has been considered. The drawer will have a multipurpose lock of EBCO premium make. The wardrobe handles are Satin SS finish of 160mm pitch. The wardrobe has a multipurpose lock of EBCO make. All hinges considered are Hettich make. Necessary good quality hardwares have been considered as required. (Item No. 51.57) |
| 39 | Item No. 1.25 - Book Case with Glass Shutter @ 825Lx300Dx1650HT Providing & Fixing of Book Case with Glass Shutter @ 825Lx300Dx1650HT:-To be made out of complete body & in 0.7mm thick CRCA & Shutter in 1.2mm thick CRCA with glass pannel in Powder coating finish as per drawing. (Item No. 51.39) |
| 40 | Item No. 1.26 - Alluminium foldable ladder for store Providing & Fixing Foldable Alluminum Ladder 1500mm. Ht. (Item No. 51.52) |
| 41 | Item No. 1.27 - Providing and Fixing Rollar Blinds AMI Make or approved make & shade of 38mm round Aluminium channel with Blackout fabric & telting with chain(Ball) system with all necessary fixtures and fitting etc. complete.(Sample to be final by Engineer In-charge prior execution of work) (Item No. 51.19) |
| 42 | Item No. 1.28 - Providing & Fixing in position, Carpet more than 800+ gsm, made with100% stain proof fibres of approved make along with 5mm underlay as per Architectural & Acoustical Design & Instructions & Complete in all aspects including all materials labour, finishing etc complete (Item No. 51.13) |
| 43 | Item No. 1.29 - Dressing Table @400LX 400DX 1800H Providing & Fixing Dressing Table of size 400LX 400DX 1800H.The Dressing table unit is made up of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2mm thick PVC edge Banding. The unit has one drawer and one shelf. The dressing table has a mirror of 4mm thick pasted on 18mm thick prelm particle board attached to the base unit. The mirror size considered is 1155 x 360 x 4(t). The mirror has been pasted using high quality 3M sticker. (Item No. 51.56) |
| 44 | Item No. 1.30 - Dressing Chair : Supply puffy of size 18\\" x 18\\" and height 16\\" cover with approved fabric on all exposed surface with necessary cushioing and foam as per approved design etc. complete (Mumbai DSR) (Item No. 102.43) |
| 45 | Item No. 1.31 - Providing & fixing in position, heavy duty fully upholstered Auditorium chairs 520mm c to c tip-up type. Height of back should be less than 1030mm with plastic protective cover on back and bottom having teak wood handles. Back to back distance is 1000mm. The auditorium chairs should be of following specifications 1. Powder Coated Heavy duty MS Stand. 2. Individually moulded, ergonomically designed seat and back cushions. 3.Moulded Polyurethane Foam cushion. PU foam density 48 – 52 Kilograms/cu.mtr 4. Moulded Polyurethane Foam manufactured in certified ISO 9001 facility to ensure consistency in density for longevity .5.Upholstered in Foam laminated stretch sandwich Fabric for clean finish and soft comfortable feel as per the colour & pattern selected by the client. 6.Seat and Back should have moulded synthetic protective cover. 7. Wooden or PU armrest 65mm x 20mm-330mm long . 8.Mounted using Anchor fasteners. (Item No. 51.18) |
| 46 | Item No. 1.32 - Providing & Fixing in position, Acoustical Panelling made from 12mm wp Ply wood & 1.5mm laminate on, 50 x 50mm Sal-wood frame of 600 x 600 c to c having wooden supports from wall of required length, in front of 1000 Gsm synthetic wool 50mm thick with chicken mesh on wall side, including cost of required Cut-Outs, decorative mouldings/finishing-items/paint & Scaffolding, as per Architectural & Acoustical Design & Instructions & Complete in all aspects.including all materials labour, finishing etc complete (Item No. 51.04) |
| 47 | Item No. 1.33 - Providing & fixing in position Stage flooring Made from 18mm plywood 1200 x 2400 & 18mm Teakwood planks 100 x 800 having tongue & grove on Sal-wood frame of 50 x 100 at 600mm c to c on stage surface including cost of required Cut-Outs, decorative mouldings/finishing-items/polish etc., as per Architectural & Acoustical Design & Instructions & Complete in all aspects. .including all materials labour, finishing etc complete (Item No. 51.06) |
| 48 | Item No. 1.34 - Providing & Fixing in position Acoustical Doors along with 150 x 150mm teak wood frame, doors made from 50mm Teak wood frame 600 x600 c to c filled with 1000 Gsm synthetic wool 50mm thick and 3mm Tecsound from both sides, 12mm waterproof ply & veneer from both sides, including 150mm heavy duty SS hinges(Geze/Dorma or eq.) 4 no each leaf, with Door-closer(Dorma/Geze or eq.) including cost of required Cut-Outs, decorative mouldings/finishing-items/melamine polish & Scaffolding as per Architectural & Acoustical Design & Instructions & Complete in all aspects .including all materials labour, finishing etc complete (Item No. 51.05) |
| 49 | Item No. 1.35 - Provding & fixing Podium whereever required of size 600x600x1275mm height with following specification table top, side & bottom- 18mm thick plywood with Fomica laminated sheet & CCWT battens 25x12mm moulding, including all leads and lifts etc. complete as per drawing and as directed by engineer in charge.(Mumbai DSR) (Item No. 102.11) |
| 50 | Item No. 1.36 - Providing & Fixing in position, 1000mm wide Auto-glow Aluminium extruded strips on auditorium steps as per Design & Instructions & Complete in all aspects. Make Piccolo or Nexus (Item No. 51.14) |
| 51 | Item No. 1.37 - Providing and fixing 12mm thk toughened etched glass as per the design, as per the design. Glass to be fixed at top & bottom in heavy guage aluminium 'c ' channel concealed in floor & boxing. Cost to be inclusive of silicon sealant to the periphery of the glass as directed.(Mumbai DSR) (Item No. 102.44) |
| 52 | Item No. 1.38 - Kitchen Trolley Providing and Fixing stainless steel kitchen trolley of overall 26 \\" height and 22\\" depth, supported on aluminium pipes, trolley basket made out of 5mm stainless steel rod fitted on telescopic channel of size 1.5 \\" x 20 \\" x 22 \\" on both sides of trolley of 12 \\" or above size, panel having 40Kilogramload bearing capacity of trolley made out of 20mm PUC coated plywood and colour combination as directed by E-I-C.Inner side of panel covered by white mica, 100mm s.s. decorative handle.(The width and height of individual compartments shall be kept as directed by Engineer-in-charge) (Item No. 51.59) |
| 53 | Item No. 1.39 - double sided name plate made out of 6mm thick sun board size of 15\\" x 8\\" pasting vinyl yellow golden letter patch on both side on black patch etc. complete.(Mumbai DSR) (Item No. 108.10) |
| 54 | Item No. 1.40 - Stool for Lab and Class-IV Providing and fixing 4 legged Lab stool, Legs made of 16 Guage 45MM Outer dimension MS Pipe, Duly painted, With a 304 Grade Stainless steel 12 inch wide seat with a 1 inch collar, Height adjustment via a screw. as per design and drawing and instructions of Engineer in charge. (Item No. 51.51) |
| 55 | Item No. 1.41 - Wooden Table for Canteen overall size 44\\" long, 28\\" width and 30\\" Height and by using Burma Teakwood legs size of 75mm x 75mm and Top frame work 75mm x 50mm cross support at end of the Top, support of bottom in H shape for legs by using 50x35 mm Teak wood. Using 19mm thick marine plywood (I.S.710/1996) for Top and finishing the Top by using 4mm veneer with Corion finishing the Table Top. The exposed area of the teakwood and ply should be finished by Melamine polish.(Mumbai DSR) (Item No. 103.05) |
| 56 | Item No. 1.42 - Canteen Table - 6 seater table size :- 1750mm w x 750mm d x 750mm h specifications :- Painting of minimum 2 h hardness on mdf top with brown laminate on bottom. Pu painted top with centre graphics. Specialled profiled edge for comforts and avoid stripping of edges.Understructure ms powder coated with a plastic cap. Pipe dia 38mm & 2mm thick fitted with top by ss machine screw.Plastic glide at the understructure to prevent damage while stacking.(Mumbai DSR) (Item No. 102.33) |
| 57 | Item No. 1.43 - Oxbow Mid Back Chair (FU7502RG)(Mumbai DSR) (Item No. 108.14) |
| 58 | Item No. 1.44 - Multiple Compartment Lockers @ 1140Lx 457D x 1830mm. Ht. Providing and fixing Multiple Compartment Lockers @ 1140Lx 457D x 1830mm. Ht. with 12 Compartments, Complete body & shutter made of CRCA Sheet with powder coated finish as per approved color. (Item No. 51.38) |
| 59 | Item No. 1.45 - Auto Glow Signages Supplying & Fixing Auto glow Signage Screen printed material A robust self andhesive sheet this can be fixed an surface which used photolumiscent material for safety signs, size 150 mm x 400 mm (Item No. 111.09) |
| 60 | Item No. 1.46 - Providing and Laying hot applied thermoplastic road marking strip on Bituminous Surface of specified shade/colour of 2.5mm thick including 1.5 Refractive index reflectorizing glass beads @ 250gm/sqm .Thickness of 2.5mm is exclusive of surface applied glass beads as per IRC 35:2015. Initial Dry reflectivity RL shall be > 250 mcd/sqm/lux measured in the initial 7 days and sustained reflectivity RL of 100 mcd/sqm/lux and Qd of 100 mcd/sqm/lux measured at the end of 2 years by means of a Standard Reflectometer of Zehntner, Easylux, Delta make capable of measuring RL & QD both according to IRC 35:2015 clause 15.5. The finished surface to be level, uniform, and free from streaks and holes complete as per direction of Engineer-in-charge and in accordance with applicable specifications.(Refer MORTH Clause 803 for technical Specification and Performance for IRC 35:2015). (Item No. 6.12a) |
| 61 | Item No. 1.47 - Supplying Acrylic Desk for Judge Table (Material supplied should be standard company) (Mumbai DSR) (Item No. 102.22) |
| 62 | Item No. 1.48 - Supplying and fixing of Acrylic baord 4mm thk mounted in Steel frame size 45cm x 30cm as per requirement with required lettering.(Mumbai DSR) (Item No. 102.25) |
| 63 | Item No. 1.49 - Providing and supplying foot rest below table as per approved typical drawing size and height using commercial plywood 18 mm thick with french polishing and finishing etc complete(Mumbai DSR) (Item No. 102.27) |
| 64 | Item No. 1.50 - Supplying glass table top 8 mm thick in required size and shape including finishing the all side edges machnically smoothly etc. complete.(Mumbai DSR) (Item No. 102.16) |
| 65 | Item No. 1.51 - Providing and fixing on site notice board made out of 6 mm marine ply of the requisite manufacture generally confirming to I.S.310/I.S.710-1980 backing and 12 mm thick soft board covered with tapestry/up to Rs. 200 per meter including necessary lipping (BTC), moulding, hardware, polishing etc. and Anti- termite treatment to plywood and woodwork with ten years guarantee bond etc. including all leads & lifts etc. complete as per Architect Drawing and instructions of Engineer in Charge.(Mumbai DSR) (Item No. 102.12) Please Enable Macros to View BoQ information |
