|
| 1 | Taking down centrifugal pump set form foundation existing position and transport to work shop for rewinding, replacement of spare parts as & when required as directed by Engineer in Charge and re-assembling/ re-installing the pump set in original position for pump capacity 40HP/30HP/20HP/16HP complete all as specified and directed.Note:- (a) Spare parts, winding wire required for renewal shall be measured and paid separately.(b) Necessary thimbles, lugs, insulation tape, nut bolts all items required and transportation charge for installation of motor at site will be included in the rate quoted by the contractor. No extra payment will be done to contractor.(c) After dismantling of induction motor repair of PCC foundation work will be executed with replacement of base frame of angle iron of existing size of angle if found damaged or deformed. PCC and base frame angle iron will be measured and paid separately under respective items. |
| 2 | Dismantling and opening the 40HP, 3 phase motor from pump set in existing position for carrying out rewinding work with super enamelled copper wire of suitable guage as per existing and heat varnishing with all other material and transport back to site after testing commisioning complete all as specified and directed.Note: (a) The Motor testing will be done before installation on No load for any unbalance load and should be free from vibration and if found unsatisfactory no payment will be done to contractor for defected motor. |
| 3 | All as per srl item No 2.00 here in before but of capacity 30 HP. |
| 4 | All as per srl item No 2.00 here in before but of capacity 20 HP. |
| 5 | All as per srl item No 2.00 here in before but of capacity 7.5 to 12.5 HP. |
| 6 | Supply only spare part for pump set including motor for 40 HP Centrifugal pump complete all as specified and directed. |
| 7 | Impeller CI. |
| 8 | pump shaft. |
| 9 | Neck ring. |
| 10 | Sleeve. |
| 11 | Bearings |
| 12 | Vent valve |
| 13 | Impeller Key |
| 14 | Motor cooling aluminium fan and its connected item. |
| 15 | Protective case as per existing |
| 16 | Supply only spare part for pump set including motor for 30 HP Centrifugal pump complete all as specified and directed. |
| 17 | Impeller CI. |
| 18 | pump shaft. |
| 19 | Neck ring. |
| 20 | Sleeve. |
| 21 | Bearings |
| 22 | Vent valve |
| 23 | Impeller Key |
| 24 | Motor cooling aluminium fan and its connected item. |
| 25 | Protective case as per existing |
| 26 | Supply only spare part for pump set including motor for 20 HP Centrifugal pump complete all as specified and directed. |
| 27 | Impeller CI. |
| 28 | pump shaft. |
| 29 | Neck ring. |
| 30 | Sleeve. |
| 31 | Bearings |
| 32 | Rubber coupling for 40 HP to 30 HP motor. |
| 33 | Vent valve |
| 34 | Impeller Key |
| 35 | Motor cooling aluminium fan and its connected item. |
| 36 | Protective case as per existing |
| 37 | Supply only spare part for pump set including motor for 7.5 HP 12.5 HP Centrifugal pump complete all as specified and directed. |
| 38 | Impeller CI. |
| 39 | pump shaft. |
| 40 | Neck ring. |
| 41 | Sleeve. |
| 42 | Bearings |
| 43 | Vent valve |
| 44 | Impeller Key |
| 45 | Motor cooling aluminium fan and its connected item. |
| 46 | Protective case as per existing |
| 47 | Supply & fixing of rubber coupling TC-13, TC-14, TC-16 and as per existing required for centrifugal pump sets complete all as specified & directed. Please Enable Macros to View BoQ information |
| 48 | Supply & fixing of rubber coupling TC-13, TC-14, TC-16 and as per existing required for centrifugal pump sets complete all as specified & directed. Please Enable Macros to View BoQ information |
