|
| 1 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 cement : 4 coarse sand (zone-iii) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) DSR 2023 (Civil), Item No. 4.1.8 |
| 2 | Supply and fixing of Coloured cement concrete saucer drain size 325X100X1000 MM grade M-25 including supply of all material/labour/ T&P etc.required for proper completion of work as directed by engineer - in -charge. complete in all respect. UPBTV WORK |
| 3 | Providing & Fixing PVC pipe conforming to IS make working pressure 6kg/sqcm including testing labour T&P and all complete fittings 110 mm diameter PWD SOR 2023-24, Item No. 30/ch.23 |
| 4 | Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.DSR 2023 (Civil), Item No. 12.44 |
| 5 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. DSR 2023 (Civil), Item No. 12.22 |
| 6 | Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material.SI No- 12.1 PWD SOR-2025-26, Ch.6, Item No.1 |
| 7 | Construction of Granular Sub Base by Providing Granular Material, spreading in uniform layers with Motor Grader on prepared surface, mixing by mix in placed method with Froont & Loader at OMC and compacting with Vibratory Roller to achieve the desired density, complete as per clause 401 Analysis Rate |
| 8 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 cement : 4 coarse sand (zone-iii) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) DSR-2023, Item No. 4.1.8 |
| 9 | Brick work in 1:4 Cement Mortar in Foundation complete excluding pointing and plastring as per drawings and technical specifications clauses 1300 PWD SOR-2025-26 Ch.6, Item No. 5 |
| 10 | Brick work with common burnt clay machine moulded F.P.S. (non modular) bricks of class designation 12.5 in exposed brick work including making horizontal and vertical grooves 10 mm wide 12 mm deep complete in cement mortar 1:6 (1 cement : 6 coarse sand). Above plinth level upto floor V level DSR-2023, Item No. 6.29.2 |
| 11 | Stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately) : Red sand stone - exposed face fine dressed with rough backing.30 mm thick DSR-2023, Item No. 8.14.1.5 |
| 12 | Providing and fixing expansion hold fasteners on C.C. /R.C.C./Brick masonry surface backing including drilling necessary holes and the cost of bolt etc complete. Fastener with threaded dia 12 mm DSR Civil-2023, Item No. 8.8.1.3 |
| 13 | Providing and fixing stainless steel cramps of required size and shape for anchoring stone wall lining to the backing or securing adjacent stones in stone wall lining in cement mortar 1:2 (1 cement : 2 coarse sand), including making the necessary chases in stone and holes in walls wherever required. DSR Civil-2023, Item No. 8.7.2 |
| 14 | 40 mm thick rubbed stone flooring over 20 mm (average) thick base of cement mortar 1:5 (1 cement : 5 coarse sand) with joints 3 mm thick, side buttered with cement mortar 1:2 (1 cement : 2 stone dust) admixed with pigment to match the shade of stone and pointing withsame mortar. Red sand stone DSR-2023, Item No. 11.30.1] |
| 15 | Providing & Fixing red sand Stone Chhatri (2.40M DIA) with 4 nos. Column 0.30m dia & Column height 2.70mtr with Projection as per drwaings all complete as per site-in-charge. As per quoattion |
| 16 | Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material.SI No- 12.1 PWD SOR-2025-26, Ch.6, Item No.1 |
| 17 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 cement : 4 coarse sand (zone-iii) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) DSR-2023, Item No. 4.1.8 |
| 18 | Chequered terrazo tiles 22 mm thick with graded marble chips of size up to 6 mm in floors, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand) : Light shade pigment using white cement DSR-2023, Item No. 11.19.1 |
| 19 | Reinforcement Cement Concrete (M-20) in Open Foundation Complete As per drawing and Technical Specifications Clause 1500,1600 & 2100 including cost of shuttering work. PWD SOR-2025-26 Ch.6, Item No.8 |
| 20 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. thermo-mechanically treated bars of grade fe-500D or more. DSR 2023 (Civil), Item No. No.5.22.6 |
| 21 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. DSR 2023 (Civil), Item No. 10.2 |
| 22 | Providing and fixing expansion hold fasteners on C.C. /R.C.C./Brick masonry surface backing including drilling necessary holes and the cost of bolt etc complete. Wedge expansion type Fastener with threaded dia 10 mm DSR 2023 (Civil), Item No. 8.8.1.2 |
| 23 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes DSR 2023 (Civil), Item No. 10.16.1 |
| 24 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. DSR 2023 (Civil), Item No.10.25.2 |
| 25 | Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer’s specifications including appropriate priming coat, preparation of surface, etc. complete. On steel work DSR 2023 (Civil), Item No.13.52.1 |
| 26 | Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material.SI No- 12.1 PWD SOR-2025-26, Ch.6, Item No.1 |
| 27 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 cement : 4 coarse sand (zone-iii) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) DSR-2023, Item No. 4.1.8 |
| 28 | Reinforced Cement Concrete (M-25) in open Foundation complete as per Drawing and Technical Specifications Clause 1500,1600 & 1700 PWD SOR-2025-26 Ch.6, Item No. 9 |
| 29 | Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. thermo-mechanically treated bars of grade fe-500D or more. DSR-2023, Item No. 5.22.6 |
| 30 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. DSR Civil-2023, Item No.10.2 |
| 31 | Lettering with black Japan paint of approved brand and manufacture DSR Civil-2023, Item No.13.71 |
| 32 | Stone work ashlar sunk or moulded or sunk and moulded upto floor five level in cement mortar 1:6 (1 cement : 6 coarse sand) including pointing with white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : Red sand stone DSR 2023 (Civil), Item no. 7.20.1 |
| 33 | Extra for stone work ashlar sunk or moulded or sunk and moulded or carved in : Triangular or Square or rectangular pillars DSR 2023 (Civil), Item No. 7.21.1 |
| 34 | Extra for stone work ashlar sunk or moulded in cornices. DSR 2023 (Civil), Item No. 7.22 |
| 35 | Tubular Markers (Spring post or Spring Bollard)S/F of plastic Tubular bollards having 450 mm Height, shall be attached to the pavemet to display the minimum 50 mm width of reflective bands to the approaching road users including labour, material, T&P etc. for propar completion of the, work. 450mm height PWD SOR-2025-26, Item No23, ch.8 |
| 36 | Providing precast cement concrete Jali 1:2:4 (1 cement : 2 coarse sand(zone-iii) : 4 graded stone aggregate 6mm nominal size ), reinforced with 1.6 mm dia mild steel wire, including centering and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3 (1 cement: 3 fine sand) etc. complete, excluding plastering of the jambs, sills and soffits. 50 mm thick DSR 2023 (Civil), Item No. 5.18.1 |
| 37 | Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: (a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. (b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. (c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places. DSR 2023 (Civil), Item No. 8.32 |
| 38 | Supply and fixing of recess/ Surface/ Pendent mounting round 6 Watt 8 Watt LED Down Lighter having Powder coated die cast aluminium housing with heat sink, diffuser/ Reflector and driver set complete in all respect. CAT- AAA PWD SOR-2018 |
| 39 | Supply and fixing of decorative 8 to 16 Watt LEDbollard luminaire with driver set confirming to IP 65 protection complete in all respect. PWD SOR-2018-Item No. 1442 |
| 40 | Construction of Granular Sub Base by Providing Granular Material, spreading in uniform layers with Motor Grader on prepared surface, mixing by mix in placed method with Froont & Loader at OMC and compacting with Vibratory Roller to achieve the desired density, complete as per clause 401 Analysis Rate |
| 41 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 cement : 4 coarse sand (zone-iii) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 42 | Construction of un-reinforced, plain cement concrete avement thickness as per disign, over a prepared sub base with 43 grade cement or any other type as per Clause 1501.2.2 M-30 (Grade). coarse and fine aggregate conforming to IS 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction, expansion, construction and constructionl joints, applying debonding strips, primer, sealant, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14 days, curing compund (where specified) and water finishing to lines and grade as per drawing and technical specification clause 1501. (For Mathura) PWD SOR 2025-26, Ch.5, Item No.13 |
| 43 | Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. thermo-mechanically treated bars of grade FE-500D or more DSR-2023, Item No. 5.22.6 . |
| 44 | Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material.SI No- 12.1 PWD SOR-2025-26, Ch.6, Item No.1 |
| 45 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :- 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) DSR-2023, Item No. 4.1.8 |
| 46 | Construction of Granular Sub Base by Providing Granular Material, spreading in uniform layers with Motor Grader on prepared surface, mixing by mix in placed method with Froont & Loader at OMC and compacting with Vibratory Roller to achieve the desired density, complete as per clause 401 Analysis Rate |
| 47 | Reinforced Cement Concrete (M-25) in open Foundation complete as per Drawing and Technical Specifications Clause 1500,1600 & 1700 including cost of shuttering work PWD SOR-2025-26 Ch.6, Item No. 9 |
| 48 | Reinforced Cement Concrete (M-25) in Sub-structure complete as per Drawing and Technical Specifications Clause 1500,1600 & 1700 including cost of shuttering work PWD SOR-2025-26 Ch.6, Item No. 14 |
| 49 | Reinforced Cement Concrete (M-25) in Super-structure complete as per Drawing and Technical Specifications Clause 1500,1600 & 1700 including cost of shuttering work PWD SOR-2025-26 Ch.6, Item No. 17 |
| 50 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. thermo-mechanically treated bars of grade fe-500D or more. DSR-2023, Item No. 5.22.6 |
| 51 | Brick work in 1:4 Cement Mortar in Foundation complete excluding pointing and plastring as per drawings and technical specifications clauses 1300 PWD SOR-2025-26 Ch.6, Item No. 5 |
| 52 | Brick work with common burnt clay machine moulded F.P.S. (non modular) bricks of class designation 12.5 in exposed brick work including making horizontal and vertical grooves 10 mm wide 12 mm deep complete in cement mortar 1:6 (1 cement : 6 coarse sand). Above plinth level upto floor V level DSR-2023, Item No. 6.29.2 |
| 53 | Supply, fabricating, transporting, hoisting and fixing in position good quality durable Mirzapur sand stone/ any other type of white sand stone in various elements for all level all height. Stone shall be free from cracks, lines, stains, white spots of efflorescence and even in shade for each elements. The stone shall be fine grained and reddish or buff-colored (locally available). The work shall be carried out as per attached drawings with differant process of i.e carving (manual/ by machine), ornamental work, traditional work, figure work (any type, any size), CNC cutting, moulding. The drawings provided are vary preliminary and amount of carving will be more then what is shown on the drawings. The carving and molding work shall be of very good quality. The stones to be fixed in line, level and plumb in all respect with the use of brass clamps, pins, dowels, cement slurry with matching pigment and Epoxy of Akemi Germany, Ardex Endura, MYK laticrete or approved make as required and as approved by the Architects. As per Analysis Item No. 7.20.2 |
| 54 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, j ointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making j oints with or without grooves (thickness of j oints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). DSR -2023, Item No.16.69 |
| 55 | Supply & Laying of precast concrete Blocks (Interlocking tiles) for paving of thickness 60mm to 100mm (Compressive strength not less then 30Mpa as specified in IS: 15658) Including 25mm thick local sand base levelling and dressing of surface to required level and slope, filling joints with local sand all complete work as specified in IS 15658:2006, 80mm Ruberd Moulded Colour SOR25-26 Ch.05, Item No. 17 New Item |
| 56 | Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) DSR-2023, Item No. 13.46.1 |
| 57 | Providing & Fixing FRP Material Goverdhan Parvat 2.00-3.00mtr Length & 1.5-2.00mtr Height Approx with Lord Krishan Hand all Complete as per Site in charge. As per Quotation |
| 58 | Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S.clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc 16 sqmm 4 core SOR-2018, Item No. 501 (i) |
| 59 | Supply and fixing of LED Street light Fitting having die cast aluminium body and diffuser with driver set suitable for 110 to 130 Watt. Confirming to IP 66 Protection complete in all respect. CAT- AAA PWD SOR-2018, Item No. 1424 |
| 60 | Supply & fixing of 8mtr GI Octagonal Pole of approved make (top dia 70mm, Bottom dia 135 mm and base plate 12mm thik) having 3mm thikness with single arm bracket (1 Mtr length) on RCC foundation including the cost of foundation, foundation bolts, excavation & backfilling and Required T&P completee in all respect.PWD SOR-2018, Item No. 643 |
| 61 | Earthing with G.l. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover late having locking arrangement and watering pipe of 2.7 metre long etc. (but without charcoal/ coke and salt) as required. DSR-2022 (Ele.), Item No. 5.3 |
| 62 | Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. 2x2.5 sq.mm DSR-2022 (Ele.), Item No. 1.17.11 |
| 63 | Supply and fixing following capacity of automatic street light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting of time switch TSO 100 series with contactoresm HRC fuses, isolating switch metering instrument & instrument box with CTs etc. in case of TPN, complete in all respect. 40 A TPN SOR (E), S.No. 807 f |
| 64 | Supply & burring of Safe Earthing Electrode T-19, (Hot Dip Galvanized), length upto 3000mm, outer dia 50mm, inner dia 25 mm, terminal dia 12mm, outer GI pipe of 16 SWG and inner GI pipe of 12 SWG with Hot Dip Galvanization upto 100 micron filled with crystalline conductive mixture (CCM) having anti corrosive & conductive property with 50 kgs activated soil (BFC) capable of reducing the soil resistivity with good mixture of retaining capacity and one earthing lead of 25mm x 3mm GI strip, upto switch board (from apron to switch board, the cost of GI strip will be extra) along with 30 cm square CI frame with hinged cover & masonry housing. Make : As approved in UP PWD & CPRI certified. SOR (E), S.No. 725.B |
| 65 | Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/submain wiring/ cable as required. DSR 20225.18 |
| 66 | Supply & Fixiing of Approx 700mm Height Pedestal made of CI/Aluminium to be fitted on existing pole duly Polyester/PU Coated. As per Analysis |
| 67 | Supply & Fixing of Single Arm Bracket fitted with Morpankh on the top and Casted embellishment at the bottom made of mild steel and painted in PU/Polyester Coating in approved colour shade. As per Analysis |
| 68 | Supply & Fixing of Double Arm Decorative Bracket fitted with Morpankh on the top and Casted embellishment at the bottom made of mild steel and painted in PU/Polyester Coating in approved colour shade As per Analysis |
| 69 | Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required 63 mm dia (OD-63 mm & ID-51 mm nominal) DSR (E)-2022, Item No. 14.16.1 |
| 70 | 120 mm dia (OD-120 mm & ID-103 mm nominal) DSR (E)-2022, Item No. 14.16.3 |
| 71 | Supply and fixing of brass nickle plated compression gland for PVC insulated & armoured served sheathed, underground cable including rubber ring etc. complete in all respect. The armouring of the cable shall be properly connected with the earth as per direction of Engineer Incharge.16 sq. mm 4 core SOR (E) sr. no.503 (i) |
| 72 | Supply and fixing of plain or pin type copper tin platedcable socket ( lug ) to the cable leads, insulating with tapeand making connection etc. complete in all respect as perdirection of the Engineer-Incharge. 4sqmm SOR (E) sr. no.504 (a |
| 73 | Supply and fixing of 4sqmm 2 core flat twin AL Cable complete with Labour T&P as per direction by E/L PSR SOR (E) |
| 74 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer-in-charge. Nominal concrete 1:3:6 or richer mix DSR Civil-2023, Item No. 15.2.1 |
| 75 | Dismantling steel work in single sections including dismembering and stacking within 50 metres lead in Channels, angles, tees and flats DSR Civil-2023, Item No. 15.17.2 |
| 76 | Dismantling Brick / Tile work/ rubble masonary/ pitching/ etc by mechanical means PWD SOR 2022-26 Ch 4, Item No. 4 |
| 77 | Dismantling of existing structures Prestressed / reinforced cement concrete grade By Mechanical Means Cement Concrete Grade M-20 & above PWD SOR 2022-26 Ch 4, Item No. 2 |
| 78 | Dismantling of cement concrete pavement by mechanical means using pneumatic tools, breaking to pieces not exceeding 0.02 cum in volume and stock piling at designated locations and disposal of dismantled materials up to a lead of 1000 metres, stacking serviceable and unserviceable materials separately PWD SOR 2022-26 Ch 4, Item No. 6 |
| 79 | Dismantling of flexible pavements and disposal of dismantled materials up to a lead of 1000 metres, stacking serviceable and unserviceable materials separately By Mechanical Means Bituminous courses DSR Civil-2023, Item No. 15.59 |
| 80 | Taking out existing CC interlocking paver blocks from footpath/ central verge, including removal of rubbish etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material within 50 metre lead as per direction of Engineer-in-Charge. DSR Civil-2023, Item No. 16.83 |
| 81 | Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in-charge.Note - item to be applicable in urban areas having directions for restricted hours for movement/ plying of load carrying motor vehicle of 3.5 cum or more.PWD SOR 2025-26, Ch 1, Item No. 231a |
| 82 | Less 5% as per GO Please Enable Macros to View BoQ information |
