|
| 1 | Demolition of precast concrete block masonry built in cement morter complete all as specified and directed by Engineer-in-charge.. |
| 2 | M&L Pre-cast cement concrete block masonry with solid blocks of mix (1:3:6) type C1 exc.10 CM in width and setting in cement mortar (1:6) Complete complete all as specified and directed. |
| 3 | Taking down cement plaster on brick or stone walls etc including raking out joints hacking for key scrubbing down with water etc. |
| 4 | M&L for Rendering 15mm thick in CM (1:4) on block masonry surfaces finished even and smooth without using extra cement. complete all as specified and directed |
| 5 | M&L for preparation of new or previously untreated plastered external surfaces and applying two coats of exterior emulsion paint (in camouflage pattern as approved by the GE) over a coat of primer all as specified and directed by EIC. |
| 6 | Demolition of cement concrete of any description and in any position not otherwise specifically provided for. |
| 7 | M&L75 mm thick for PCC 1:3:6 type C2 (using 20mm graded stone aggregate) as in plinth protection/ path/ hard standing/base of Interlocking tiles, Checured tiles etc complete all as specified. |
| 8 | M&L100 mm thick for PCC 1:2:4 type B2 (using 20mm graded aggregate) as in path/ hard standing finishing smooth without using extra cement complete all as specified. |
| 9 | M&L100 mm thick for PCC 1:4:8 type D2 (using 40mm graded aggregate) as in path/ hard standing complete all as specified. |
| 10 | Finishing surface of concrete roads, pavements, by brooming |
| 11 | Forming contraction (Dummy) joints 65mm X 10mm wide, filled with sealing compound Gde 'B' for key scrubbing down with water etc. |
| 12 | Dismantling Stone slabs and tiles laid dry of any description or thickness in floors, aprons etc. |
| 13 | M & L Machine pressed precast concrete interlocking paver block with grey cement no pigment in any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade complte all as specified and directed |
| 14 | M & L Sand filling under floors or in foundations including watering and consolidation complete all as specified directed |
| 15 | Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and as directed. |
| 16 | S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 |
| 17 | M&L for preparation of new or previously untreated surfaces of any description, not otherwise described, exc 10 cm in width or girth and applying two coat of synthetic enamel paint over one coat of red oxide primer on new steel surfaces al as specified. |
| 18 | S&F in repairs Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured. |
| 19 | Dismantling existing galvanised steel punchedtype concertina coil 1050 mm dia placed on top of the wall inside the angle iron horns/GI barbed wire, tying with necessary GI wire complete all as specified and directed. |
| 20 | Supply and fixing galvanised steel punched type concertina coil 1050 mm dia when stretched (stretched to 8 mtr length) placing on top of the wall inside the Angle iron horns/GI barbed wire, tying with necessary GI wire complete all as specified and directed. |
| 21 | Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground embedded in concrete |
| 22 | Dismantling fencing wire mesh, any type |
| 23 | S&F chain link fencing plastic coated MS wire made out of 3.5mm outer dia, of size 75 mm x 75 mm, including straining bolts etc. including provn of binding wire or with nuts/bolts complete all as specified and as directed by the EIC. |
| 24 | M & L for 10 mm dia and over round bars cut to length bent to shape reqd incl cranking bending, spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality conforming to Fe 290 Gde E-165. |
| 25 | Excavating in post holes (or similar holes) each n exc 0.5 Cum & getting out in soft/loose soil |
| 26 | S&F Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts;posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 |
| 27 | Material & labour for PCC 1:3:6 type C2 as in foundation, filling, and mass concrete complete all as specified and directed by Engineer-in-Charge. |
| 28 | Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for. |
| 29 | M&L for Precast RCC cover slabs in 1:2:4 type B1(using 20 mm graded stone aggregate) as in landings, cover slabs, etc. |
| 30 | M&L for Mild steel deformed TMT bars, 10 mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips all as specified. |
| 31 | M&L for Plain cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) 40mm thick as in bed of drain, surface to be finished even and fair without using extra cement. |
| 32 | M&L for Plain cement concrete 1:3:6 type C1 (using 20mm graded stone aggregate) as in coping including weathering, slightly rounded or chamfered angles and including necessary form work. |
| 33 | M&L for form work to soffits of suspended slabs, such as roof slabs floor slabs and similar work not exc 200 mm thick for rough finished surfaces of concrete all as specified. |
| 34 | M & L for Reinforced cement concrete (nominal mix Type B1 1:2:4) ( 20 mm graded stone aggregate) as in slabs supported on walls , beams and Columns in floors , roofs , landings , balconies , canopies , deck slab complete all as specified and directed |
| 35 | Demolition and breaking up drain pipes 300mm Dia. (salt glazed ware , AC or rinforced concrete ) set in cement mortar complete all as specified and directed |
| 36 | M&L reinforced concrete pipes, class NP3, laid and jointed complete with collars of 300 mm laid to slope in trenches, jointed in CM 1:1 and tested complete all as specified and as directed. |
| 37 | M&L cement concrete (1:4:8) type D2 using 40 mm graded stone aggregate as in bed to drain pipe including forming cradles complete for pipe of size 300 mm bore all as specified and as directed. |
| 38 | M&L in repair of pot holes by using cold readymix bitumenous concrete by proper compaction of Tikitar shelmac PR or equivalent all as per manufacturers instruction and as directed by Engr-in-Charge |
| 39 | M&L for 20mm thick Granite (Z Black) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like including 20mm thick screed bed of cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, complete all as specified and as directed. NOTE : Cost of Screed Bed shall deemed to be included in QUOTED UNIT RATE. |
| 40 | M&L Dholpur Stone Pillar/Column of roughly squared stones uniform colour of each of size 140x150x900mm, cut with machine cut edges dressed and fixed with CM complete all as directed. |
| 41 | M&L Dholpur sand stone jali railing thickness 20-25mm natutal polished ractangular shape uniform colour cut with machine cut edges dressed and fixed with polishing, rubbing & including silicon treatment complete all as directed. |
| 42 | M&L for Dholpur stone cladding gang saw cut with machine cut edges, uniformcolour of each stone size exceeding 0.25 sqm area and not exceeding 0.5 sqm fixed with and including one number SS clamps (grade -202) of flat 30mm X 2mm, 150mm long made to shape in each slab, making V groove at top and bottom of stone and drilling hole for hold fastener, polishing, rubbing & including silicon treatment ® Please Enable Macros to View BoQ information |
