|
| 1 | 1. FRP Molded Canopy (Gazebo Hex. Shape) Double Finishing sheet in 18`Diai) 6 No. Ornamental Design FRP Molded Pillar FRP Hexagonal Pillar base each side 195mm with vertical fitted design and height 970mm and having B class vertical m.s round pipe of size 88 mmX2.5mm thick and height 2890mm, the central m.s pipe holds FRP Molded taj 6no of size 260 x 260 x 210mm high suitably mounted at appropriate height complete as per design. Complete pillar suitably grinded and subsequently spray painted with two coats of P.0 Paints (1st Coat of Epoxy Surface Tolerance Primer INTERSEAL 670HS and 2nd Coat of PU finish Paint INTERTHANE 990 or Equal lent ( in required shade).ii)12 No. spndred and 6 no. FriezesFloral and Ornate decorative design combination of spandrel and frieze, matched to be suspended between two m.s pillars as per the design. The spandrel (L-Bracket) having length 420mm and height 400mm the frieze (Top Panel) height 250mm and length as per the size of the gazebo. The frieze mounted on m.s tabular pipe frame of size 50mm x 25mm, frieze properly welded to the column pillars at either ends. Complete set of spandrel and frieze uniformly grinded spray primered, spray painted with P.0 Paints(1st Coat of Epoxy Surface Tolerance Primer INTERSEAL 670HS and 2nd Coat of PU finish Paint INTERTHANE 990 or Equal lent ( in required shade)..iii) 3 No. M S rectangular tube /frp base panel railing with frameFloral and Ornate decorative design M S square pipe /frp side railing panel as per design having height of 730mm and length as per size of Gazebo. Each panel top and bottom mounted with mild steel tubular pipe frame of size 50 x 25 mm. The bottom mild steel pipe having 2 nos. of hold fasts in m.s pipe of size 40 x 40mm and length 250mm welded at the base to hold the panel in the ground. Every panel length is as per the gap between the two pillars. The complete railing panel grinded for neat surface finishes spray primered and subsequently spray painted with P.0 Paint in required shade(1st Coat of Epoxy Surface Tolerance Primer INTERSEAL 670HS and 2nd Coat of PU finish Paint INTERTHANE 990 or Equal lent ( in required shade).iv) One set of top frame with Double Finishing FRP Molded roof Top frame in MS tubular pipe of size 40 x 40mm properly welded and grinded. The top frame mounted with FRP molded Sheet of 4 mm thick with top and bottom good finishing (Double finishing sheet) to make it rust proof bent to profile of size 245mm width on either ends fixed horizontally along the length between column pillars. Also it contain FRP Molded Diamond Shape of 14` x 3 mm thick at the central top for its beautification. Each such sheet properly riveted to horizontal sheets. Complete canopy flooring with kota flooring/tile flooring at site as decided by Engineer-in-Charge and without sitting bench at site1. LED Light Strip from inside the canopy for Ambience look2. 1 Nos of Ceiling Fan inside the Canopy The scope includes complete fabrication, transportation, on-site installation, and commissioning with all necessary materials, labour, and accessories, to be completed as directed by the Engineer-in-Charge. |
| 2 | 4-Seater See-Saw. i. FRP coated Frame and Structure (Main Frame Material):• Heavy-duty MS pipe (mild steel), ISI grade, FRP coated• Pipe thickness: 3.0 mm • Fulcrum/Base Support:• MS square/round pipe, min. 80 mm OD × 3.0 mm thickness• Pivot support with ball bearing or heavy-duty bush for smooth movement.ii. Dimensions• Overall Length: 3.0 mtr• Height at Seat Level (rest position): 600 – 750 mm• Height at Maximum Tilt: ~1.2 m• Beam Size: 80 mm OD round/rectangular pipe, thickness 3.0 mm.iii. Seats• Material: FRP (Fiber Reinforced Plastic) • Size per seat: 300 mm × 250 mm• Quantity: 4 (two on each side, facing each other)• Backrest (optional): For toddlers, height ~200 mmiv. Handles and Footrest• Handlebar: MS pipe Ø 25–32 mm, height 350–400 mm above seat• Footrest: MS rod/pipe with anti-slip rubber gripv. Load Capacity• Per Seat Capacity: 40–60 kg• Total Safe Load: ~200–240 kgvi. Safety Features• Stoppers at both ends with rubber pads to avoid sudden impact• Rounded edges and smooth powder coating (non-toxic)• Bearing/bushing enclosed for safetyvii. Age Group Suitability• 4–12 years recommended• Supervised use for younger childrenviii. Installation: - Base plates with grouting bolts in RCC foundation (min. 300 × 300 × 450 mm deep footing). Ensure minimum 2 m safe clearance zone around the see-saw |
| 3 | Arch swing: - i. FRP Coated Frame and Structure• Type: Arch frame, single bay (2-seater) • Material: ISI grade MS (mild steel) pipes.• Pipe OD (arch legs): 80 mm (min.) × 3.0 mm thickness• Top cross beam: 80 mm OD MS pipe × 3.0 mm thickness• Arch shape: Radius : 1 mtr (depending on bay width)ii. Dimensions• Height (ground to top beam): 2.6 – 3.0 m (recommended 2.8 m)• Seat clearance from ground (at rest): 350–500 mm• Distance between two swing seats (side-to-side): Minimum 600–750 mmiii. Swing Seats• Material: FRP • Type: Flat seat (for 5–12 yrs)• Size: 400–450 mm × 200–250 mm• Load capacity per seat: 80–120 kgiv. Chains / Ropes• Type: Galvanized / stainless-steel chain with plastic/rubber coating (pinch-free) as desired by Engineer in-charge • Chain thickness: 6–8 mm• Length: 1.6 - 1.8 m (adjustable for seat clearance)• Connection: Heavy-duty D-shackles or clevis connectors with anti-theft nut/bolt.v. Safety Zone and Surfacing• Impact area: At least 2.0 m front and back, 1.75 m side clearance per swing.• Fall height: 1.5 – 1.8 mvi. Load Capacity and Stability• Single bay (2 seats): Total ~200 kg• Multi-bay: Each bay must be independently anchored• Foundation: RCC footing per arch leg, size 300 × 300 × 600 mm depth with anchor boltsvii. Age Group Suitability• Toddlers (2–5 yrs): Bucket seat with harness.• Kids (5–12 yrs): Flat belt/FRP seat |
| 4 | Single Slide: - Single-lane i. FRP Coated Structure and Material• Main frame fabricated from MS (Mild Steel) tubular pipes of minimum 50 mm diameter and 3 mm thickness, conforming to ISI standards.• Supporting legs to be embedded in M-15 grade cement concrete block (1:2:4 mix) of size not less than 450 mm × 450 mm × 600 mm (depth).• Platform frame made of MS angle iron-FRP Coated (40 × 5 mm) 42 MM OD PIPE with chequered sheet/8 mm FRP sheet / for anti-skid surface.ii. Slides• Single slide made of FRP (Fiber Reinforced Plastic) • Length of slide: 2.5 m to 3.0 m (approx.) from top to bottom.• Height of starting platform: 1.80 MTR (approx.) above ground level.iii. Safety Features• Handrails made of MS pipes- FRP coated (25 mm Dia, 2.5 mm thick) provided on both sides of stairs and top platform.• Safety guard/barriers of minimum 600 mm height at the platform to prevent accidental fall.• All sharp edges, welding joints and corners to be properly ground and rounded.iv. Ladder/Stairs• Ladder made of MS pipe-FRP Coated (32 mm dia, 3 mm thick) with non-slip rungs of MS flats (25 mm × 5 mm).• Angle of inclination of ladder approx. 60° for safe climbing.v. Finishing• All MS parts to be treated with anti-rust epoxy primer and FRP coating.• FRP surface to be glossy, UV-resistant and smooth finished.vi. Load Bearing Capacity• Slide should be able to withstand a minimum load of 150 kg at any point without deformation.vii. Standards and Workmanship• The equipment must conform to IS: 9873 (Part I–III) / IS: 6661 / IS: 875 (as applicable) and international playground safety standards.Workmanship should ensure durability, stability, and child safety. |
| 5 | Climber :-i. Material FRP coated • Main frame: Mild Steel (MS) pipes of minimum 40 NB / 48 mm outer diameter, thickness 3 mm, conforming to ISI standards.• Climbing elements: High-strength steel pipes, Fasteners: M.S bolts, nuts, and washers with anti-rust coating.ii. Surface Finish• All MS components to be FRP coated with weather-resistant, non-toxic paint.• Welded joints properly ground and treated with anti-corrosive primer before painting or coating.iii. Dimensions (example for arch/net climber, modify as required)• Height: 2.0 – 2.5 meters.• Width: 1.5-2.0 mtr • Safe spacing between climbing bars: 250-350 mm.iv. Safety Features• All edges and corners to be rounded (no sharp edges).• Fall height should comply with IS 9873 (Part 9): Safety Requirements for Playground Equipment.• Rope joints/knots with galvanized clamps and protective sleeves.• Anchoring to be done with RCC foundation blocks (1.5 ft x 1.5 ft x 1.5 ft) using grouted bolts.v. Load Bearing Capacity • Minimum 100 kg per user, tested for at least 250 kg total load.vi. Standards Compliance• IS 9873 (Safety of Toys and Play Equipment).• EN 1176 (International Playground Equipment Safety Standard) where applicable.vii. Installation• Installation as per manufacturer’s guidelines.• RCC foundation cured for minimum 7 days before usage.viii. Maintenance• Annual inspection for structural stability.• Repainting and tightening of nuts/bolts every 12 months. |
| 6 | Six-Seater MGR i. FRP coated Material and Construction:• Main Frame: Made of heavy-duty MS (Mild Steel) pipes/tubes, minimum 48 MM OD PIPE Top and Bottom Plate: MS plates, minimum 3.0 mm thick, precision cut and welded.• Arms: Six FRP coated arms made of MS pipe (minimum 32 mm dia, 2.6 mm thick), equally spaced.• Seating Arrangement: Six ergonomically designed FRP (Fiberglass Reinforced Plastic) seats with back support, UV resistant, weatherproof, and anti-crack finish.• Central Shaft: MS solid shaft of 45-50 mm dia with double ball bearings for smooth rotation.• Bearing Housing: Heavy-duty cast iron/steel housing with dust-proof cover.• Footrest: Provided for each seat, made of MS rod 27 mm dia.ii. Dimensions (Approx.):• Diameter of Ride: 1.8 to 2.0 mm • Seating Capacity: 6 children (age group 5–12 years)• Height: 0.6 m – 0.75 m (from ground level to seat level)iii. Finish• All MS parts to be sandblasted, treated with anti-rust primer, and FRP-coated with multi-color finish.• FRP seats in bright, attractive child-friendly colors.iv. Safety Features• Rounded edges, no sharp corners.• Safe rotating speed due to self-regulated design.• Anti-skid footrest.• Bearing assembly fully covered for child safety.v. Installation:• Foundation with 1:2:4 RCC concrete blocks (minimum 400 × 400 × 600 mm), as per manufacturer’s design.• Installation to be done with proper grouting and alignment. |
| 7 | Fire Station Climber: -i. Structure and Material• Main Frame: Heavy-duty MS (Mild Steel) pipes of minimum 48 mm OD, 2.5 mm thick, FRP-coated / PU PAINT for rust resistance.• Platforms and Panels: 3.0 mm thick MS sheet with anti-skid surface, FRP-coated.• Fasteners: PLATING bolts, tamper-proof, with plastic caps.• SEATING: FRP (Fiber Reinforced Plastic) fire-station theme seat for 8 children in bright red with fire station logo.ii. Dimensions• Height: 2.0-2.4 m (depending on design).• Length: Approx. 2.5-3.5 m.• Width: 1.5-2.0 m.• Platform height: 1.2 m – 1.5 m.iii. Components• Fireman’s Pole: Vertical GI/MS pipe of 50 mm OD, FRP-coated.• Bridge (optional): Rope/metal bridge connecting two platforms.• Themed Panels: Fire station decorative FRP panels with cut-outs for windows/doors.• Wheel: 4 wheels, dia: 15-18 inch iv. Safety Features• All edges rounded and smooth for child safety.• Minimum 2 feet clear space around the climber for safety zone.• Compliant with IS 9873 (Part 1, 2 and 3) and EN 1176 safety standards for playground equipment.• No sharp projections or hazardous entrapments.v. Finishing• FRP coating / pu paint non-toxic and weather-resistant.• FRP parts: UV stabilized, fade-resistant, child-safe paints.v. Capacity• Suitable for 6–8 children at a time, age group 5–12 years. |
| 8 | Beautification of Radharaman Park through Grass Plantation, Gazebo (Hexagonal Shape) and Installation of Children Play Equipment, Ward No. 43, Division-IV, MCF (Tirkha Colony Boosting). Please Enable Macros to View BoQ information |
