|
| 1 | Cleaning of the existing black topped surface with brooms, soft brushes and finally dusting with old gunny bags and/or compressed air to receive bituminous treatment. etc. complete |
| 2 | Earth work in excavation by mechanical means (hydraulic excavator)/ manual means in foundation pipeline trenches drain |
| 3 | Supplying of 600 mm dia NP3 R.C.C. hume pipe |
| 4 | Laying and fixing with flush heavy duty non pressure NP3 class R.C.C. pipe with cement mortar in proportion 1:2 (1 cement : 2 fine sand) in joints including cost of jointing materials etc. complete.600 mm dia pipe |
| 5 | Cable Duct Across the Road (Providing and laying of a reinforced cement concrete pipe duct, 300 mm dia, across the road (new construction), extending from drain to drain in cuts and toe of slope to toe of slope in fills, constructing head walls at both ends, providing a minimum fill of granular material over top and sides of RCC pipe as per IRC:98-1997, bedded on a 0.3 m thick layer of granular material free of rock pieces, outer to outer distance of pipe at least half dia of pipe subject to minimum 450 mm in case of double and triple row ducts, joints to be made leak proof, invert level of duct to be above higher than ground level to prevent entry of water and dirt, all as per IRC: 98 - 1997 and approveddrawings.)Triple Row for three utility services |
| 6 | Raising side shoulders with hard murrum including spreading watering and consolidationSupplying of granitic or basaltic stone soling of size 15-20 cm and Murrum having P.I. Value not more than 6 and laying including packing with smaller stones and consolidation with power roller including spreading waters and consolidation of binding material etc. complete.(Measurements shall be considered on finished item.and and layer of WBM of 50/75mm thick shall be taken seperately over this sub-base to obtain smooth surface, as per the directives of Engineer in-charge). |
| 7 | Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with 3-wheeled steel/vibratory roller 8-10 tonnes in stages to proper grade and camber, applying and brooming requisite type of screening/binding materials to fill-up the interstices of coarse aggregate, watering and compacting to the required density.as per MORTH Specification 404By Manual MeansGrade - II |
| 8 | Providing and laying 50mm(consolidated thickness)full grout using granitic or basaltic stone of specified grading at 6.00 cu.m. per 100 sq.m. grouting with hot bitumen straight run bitumen(or with such bituminous material of grade and type as specified by the Engineer-in-Charge)at 5.0kg. per sq. m. binding with key aggregate of granitic or basaltic stone of specified grading at 1.5 cu.m. per 100 sq.m. including Providing and laying seal coat sealing the voids in a bituminious surface laid with F.E loader with 1 Cu.m. bucket capacity to the specified levels, grade and cross fall using Type A seal coat with 0.98 kg/sqm ofbitumen of grade as per MoRT&H specifications clause 513. |
| 9 | Rubble packing with hard laterite stone under floors including watering ramming and consolidating etc. in pipeline trenches and other foundations complete. |
| 10 | Providing and laying in position cement concrete 1:2:4 (1 cement : 2 coarse sand: 4 graded granitic or basaltic stone aggregate 40 m nominal size) excluding cost of centering, shuttering and finishing :All works upto plinth level |
| 11 | Providing and applying tack coat with bitumen grade of 80/100 or bitumen emulsion using pressure distributor on the prepared bituminous/granular surface cleaned with mechanical broom as per MoRT&H specifications clause 503.Bitumen 80/100@ 0.375 kg/sq.m |
| 12 | Providing and laying dense graded bituminious macadam with 40-60 TPH Drum Mix type HMP producing an average output of 50 tonne per hour using crushed aggregates of specified grading, premixed with bituminious binder by specified percentage of weight of total mix and filler, transporting the hotmix to work site, with all leads laying with a hydrostatic /hydraulic paver finisher with sensor to control the required grade, level and alignment, rolling with smooth wheeled, vibratory or tandem rollers to achieve the desired compaction using antistripping agent complete as per MoRT&H Specifications Clause 507Grade-II (19mm nominal size) Bitumen @ 5% of weight of mixAntistripping agent @ 0.5% of bitumen content |
| 13 | Providing and laying 30 mm thick Bituminious/Asphaltic concrete with 40-60 batch type HMP producing an average output of 50 tonnes per hour using crushed aggregates of specified gradings Premixed with bituminious binder at 6.5 % by weight of total mix and fillerusing Antistripping agent transpoting the hotmix to work site with all leads and applying a tack coat @f 2.00 kg/10sq.m. with hot bitumen of 80/100 and laying with Mechanical Paver finisher to the required grade, level and alignment, rolling with smooth wheeled, vibratory or tandem rollers to achieve the desiredcompaction as per MORT&H specifications clause 509 and 503 Antistripping agent @ 0.5% of bitumen content |
| 14 | Refilling the pipeline/foundation trenches plinth sides, foundation etc. with available excavated earth in layers not exceeding 20 cm depth consolidating each layer ramming and watering lead upto 50 M and all lifts and disposal of surplus earth as directed by Engineer in Charge. |
| 15 | Raising side shoulders with hard murrum including spreading watering and consolidationMurrum from borow puit |
| 16 | Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC :35. The finished surface to be level uniform and freefrom streaks and holes as per MORTH Specification 803 |
| 17 | Road Markers/Road Stud with Lense Reflector (Providing and fixing of road stud 100x 100 mm, die cast in aluminium, resistant to corrosive effect of salt and grit, fitted with lense reflectors, installed in concrete or asphaltic surface by drilling hole 30 mm upto a depth of 60 mm and bedded in a suitable bituminous grout or epoxy mortar, all as per BS 873 part 4:1973) Please Enable Macros to View BoQ information |
