|
| 1 | Providing and fixing aluminum work for doors ,windows, ventilators and partition with extruded built up standard tubular / appropriate Z sections and other sections of approved make conforming to IS :733 and IS :1285, fixed with rawl plugs and screws or with fixing clips ,or with expansion hold fasteners including necessary filling up of gap. at junctions , at top ,bottom and sides with required PVC/neoprene felt etc. Aluminium section shall be smooth ,rust free, straight ,mitered and jointed mechanically wherever required including cleat angle Aluminium snap beading for glazing /paneling , C.P. brass/ stainless steel screws Al. Tower bolt & Al. handle & Al. Aldrop etc.,all complete as per architectural drawings and the directions of Engineer- in – charge .(Glazing and paneling to be paid for separately). |
| 2 | For fixed portion |
| 3 | Polyester Powder coating aluminum ( minimum thickness of powder coating 50 micron) |
| 4 | For shutters builtup standard tubular sections of openable doors ,windows & ventilators including providing & fixing hinges / rollers etc. and making provision for fixing of fittings wherever required (lockes shall be paid for separately). |
| 5 | Polyester Powder coating aluminum ( minimum thickness of powder coating 50 micron) |
| 6 | Extra for shutters of sliding aluminum windows |
| 7 | Providing and fixing 12 mm thick prelaminated three layer medium density (exterior grade ) particle board Grade I, Type II conforming to IS : 12823 bonded formaldehyde synthetic resin ,of approved brand and manufacture in paneling fixed in aluminium doors ,windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and direction of engineer-in-charge. |
| 8 | Prelaminated particle board with decorative lamination on both sides. |
| 9 | Providing and fixing glazing in aluminium door, window ,ventilator shutters and partitions etc. with PVS / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge.(Cost of aluminium snap beading shall be paid in basic item.) |
| 10 | With float glass panes of 5.0 mm thickness ( weight not less than 13.50 kg/sqm) |
| 11 | Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS : 6315 marked, for doors including cost of cutting floors as required, embedding in floors and cover plates with brass pivot and single piece M.S. |
| 12 | With stainless steel cover plate |
| 13 | Filling the gap upto 5 mm depth and 5 mm width in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. |
| 14 | Providing and fixing 100mm brass locks (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete. |
| 15 | Providing and fixing expanded grill made of aluminum as per design and drawing having members section of size 7.5mm x 6.0mm and opening of size 102mm x 99mm to aluminum window/vent with required screws, Y and H aluminium section (as per drawing) at the ends and middle joints respectively complete in all respect as per direction of engineer in charge. |
| 16 | Polyester Powder coating aluminum ( minimum thickness of powder coating 50 micron) |
| 17 | S&f fixed wire gauge of stainless steel of 14 mesh x 24 gauge to the aluminium window by Aluminium beading 20x3mm with suitable screws not exceeding 150mm distance at all heights with all lead and lift with scafolding. |
| 18 | Non BSR : Providing & Fixing double glazed units at all floors in existing aluminium windows, using of hermetically sealed ( with primery sealant - Butyl & secondary sealant - Silicone or Polysulphide) 24mm thick , double glazed unit (DGU) with outer glass as 6mm thick, Soft coated silver layered reflective, low e toughened glass of approved make . Inner glass should be 6mm toughned clear glass of approved make (Iron content <1000 PPM). Both the glasses to be separated by an Aluminium spacer to create a 12mm gap which would be air filled . Moleculer sieve Desiecant to be used to fill the Aluminium Spacer. ( Measurement for payment shall be from one side of unit as per actual size) DGU specifications shall be as follows Maximum U value - 1.8 W/Sqm Dg C Maximum SHGC - 0.24 Minimum VLT - 36.00% Please Enable Macros to View BoQ information |
