Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Schedule 'A' |
| 2 | Taking down cement plaster / terrazzo / grit plaster / granular finish etc., of any description thickness including raking out joints hacking for key scrubbing down with water, complete all as specified and directed by Engineer-in-Charge. |
| 3 | Material & Labour for 10mm thick rendering in cement mortar 1:6 on brick work or concrete surfaces finished even and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge. |
| 4 | Material & Labour for 15mm thick rendering on concrete/brick surfaces in Cement Mortar 1:4 using with water proofing compound as per manufactures instruction finished even and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge. Note:- WPC measured and paid separately. |
| 5 | Material & Labour for 5mm thick rendering in Cement Mortar 1:3 on Concrete Surfaces, ceiling etc., finished surface Even and Smooth, without using extra cement, complete all as specified and directed by Engineer-in-Charge. |
| 6 | Material & Labour for preparation of newly plastered surfaces and applying three coat of white wash as in ceiling, complete all as specified and directed by Engineer-in-Charge. |
| 7 | Material & Labour for preparing newly plastered surfaces of internal wall and applying two Coats of oil emulsion distemper over 3mm thick wall care putty on wall plastered surface, complete all as specified and directed by Engineer-in-Charge. |
| 8 | Material & Labour for preparation of newly plastered surfaces and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm per Litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces, complete all as specified and directed by Engineer-in-Charge. |
| 9 | Material & Labour for complete removal of existing treatment of old plastered surfaces and applying two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm per litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces, complete all as specified and directed by Engineer-in-Charge. |
| 10 | Material & Labour for complete removal of existing treatment & washing rubbing down and stopping of distempered and painted surfaces including preparation of old undecorated surface of walls and applying two coats of oil bound distempered over 2mm thick wall care putty on wall over priming surface, complete all as specified and directed by Engineer-in-Charge. |
| 11 | Material & Labour for preparation of old surfaces of ceiling including scrapping down smoke, soot and efflorescent salts and treating oil and greasy spots, brooming down or steel wire brushing removing nails making good holes cracks etc., on plastered or un-plastered surfaces and applying one coat of white wash on ceiling surface, complete all as specified and directed by Engineer-in-Charge. |
| 12 | Material & Labour for preparation of old painted surfaces of steel of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed by Engineer-in-Charge. |
| 13 | Demolition of reinforced concrete of any description and in any position not otherwise specifically provided for including reinforcement cut as required to facilitate demolition, complete all as specified and directed by Engineer-in-Charge. |
| 14 | Material & Labour for RCC (1:2:4) nominal Mix using 20mm graded aggregate in chajjas, parapet facia etc., complete all as specified and directed by Engineer-in-Charge. |
| 15 | Material & Labour for RCC -M-25 (nominal mix) using 20mm grades stone aggregate as in Fins, fascias, louvres, parapets, and railings exc. 60cm in height, newels, balustrade, and the like, complete all as specified and directed by Engineer-in-Charge. |
| 16 | Use and waste of form work to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pilasters, buttresses, etc., vertical or to batter surface fair finished, complete all as specified and directed by Engineer-in-Charge. |
| 17 | Use and waste of form work to Chajjas and similar items including edges etc., complete all as specified and directed by Engineer-in-Charge. |
| 18 | Supply & Fixing Mild steel CRS TMT bars 6mm to 8mm dia and cut to length bent to shape required, including cranking, bending and binding as in stirrups, spacers and binders etc. with MS wire (annealed) not less than 0.9mm dia., complete all as specified and directed by Engineer-in-Charge. Note : The reinforcement shall be welded with existing reinforcement after dismantling of RCC Chajjas/Parapets etc. |
| 19 | Material & Labour for 15mm thick plaster in Cement Mortar 1:3 in two layers, with & including wire netting of galvanized steel wire 0.91mm dia and mesh size 12mm placed in walls before plaster layers and fixed with tinned tack or wire stapled where required first layer of 10mm thick plaster in cement mortar 1:4 & second layer of 5mm thick in cement mortar 1:3 including taking down of loose /bulsing surfaces of plastered or concrete as in chajjas, beam balcony fins etc., to make to original shape at any height to repair chajjas, beam balcony fins etc., in multi-storeyed buildings, top layer of plaster finished even & smooth without using extra cement complete including cleaning and preparation of existing RCC surfaces and applying a coat of cement slurry and surface shall be match & finish the existing surface by applying two or more coats of anti-fungal exterior emulsion paint, complete all as specified and directed by Engineer-in-Charge. Note : Each layer of plaster shall be done separately. |
| 20 | Expanded metal, not exceeding 4 Kg/sqm cut to length, bent to shape required and typing with and including annealed mild steel wire not less than 0.9mm dia or fixing with galvanised steel staples supplied and fixed complete to wood or steel members, complete all as specified and directed by Engineer-in-Charge. |
| 21 | Demolition of concrete of any description and in any position, complete all as specified and directed by Engineer-in-Charge. |
| 22 | Material & Labour for 25mm thick cement concrete Type B-1 1:2:4 (Using 20mm graded aggregate), complete all as specified and directed by Engineer-in-Charge. |
| 23 | Material & Labour for 15mm thick rendering in Cement Mortar (1:3) on brick or concrete surfaces in two layers mixed with water proofing compound @ 2% by weight of cement in top 5mm thick, finishing the surfaces with even and smooth with using extra cement complete all as specified and directed. ( Note:- WPC measured separately) |
| 24 | Material & Labour for Bitumen blown any grade, applied hot, two coats to concrete surfaces at the rate of 1.5 Kg / sqm per coat. Including polythene film, black, 50 micron laid in floors, complete all as specified and directed by Engineer-in-Charge. |
| 25 | Material & Labour for lean concrete (1:7:12) Type F2 laid compacted, complete all as specified and directed by Engineer-in-Charge. |
| 26 | Material & Labour for cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate as in roof kerbs PCC as in kerbs/covet fillet, complete all as specified and directed by Engineer-in-Charge. |
| 27 | Supply & Fixing GI tubing 40mm bore medium grade fixed to wall and ceiling or laying in floor as sunken spout, complete all as specified and directed by Engineer-in-Charge. |
| 28 | Supply only integral water proofing compound, complete all as specified and directed by Engineer-in-Charge. |
| 29 | Demolition of brick work as in walls/parapet walls removing grass fungus weed, roots of trees completely, grown on roof/wall surfaces, complete all as specified and directed by Engineer-in-Charge. |
| 30 | Material & Labour for Brick work with sub class ‘B’ brick, straight or curved as plan exc 6m mean radius built in cement mortar 1:6, complete all as specified and directed by Engineer-in-Charge. |
| 31 | Material & Labour for Brick work with sub class ‘B’ brick, straight or curved on plan to any radius in half brick thick walls built in Cement Mortar 1:4, complete all as specified and directed by Engineer-in-Charge. |
| 32 | Dismantling floor hearth or wall tiling/china mosaic including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed by Engineer-in-Charge. |
| 33 | Material & Labour for glazed ceramic coloured tiles of size 450 x 300 x 6 to 7mm, 450x350 or 350x250 6 to 7mm thick on vertical surface such as skirting/dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tile with & including rendering 10mm thick cement plaster in cement mortar 1:4 finished rough to fix tiles, complete all as specified and directed by Engineer-in-Charge. |
| 34 | Material & Labour for Non-skid ceramic coloured tiles 7 to 8mm thick (Square or rectangular) area of each tile exc 0.18 Sqm but not exceeding 0.36 Sqm, in floor etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over and including screed bed or bedding layer 15mm thick in cement mortar 1:6 for laying floor finishes, complete all as specified and directed by Engineer-in-Charge. |
| 35 | Material & Labour for Non-skid ceramic coloured tiles 7 to 8mm thick (Square or rectangular) area of each tile exc 0.18 Sqm but not exceeding 0.36 Sqm, as in skirting, dados in vertical surfaces etc and including 10mm thick cement plaster 1:4, complete all as specified and directed by Engineer-in-Charge. |
| 36 | Material & Labour for Granite (of any type) 18- 20mm thick work (table rubbed and polished) in tread & riser of steps, jambs, pillars, window cill, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of Granite laid over 20mm thick screed bed in Cement Mortar 1:6, complete all as specified and directed by Engineer-in-Charge. |
| 37 | Material & Labour for Vitrified ceramic tiles 10mm thick DARK SHADE(square/rectangular) polished area of each tiles not exceeding 0.36 sqm including 15mm thick screed bedding layer, in (1:6) Cement Mortar set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tile, complete all as specified and directed by Engineer-in-Charge. |
| 38 | Material & Labour for Vitrified ceramic tiles 10mm thick DARK SHADE (square/rectangular) polished area of each tiles not exceeding 0.36 sqm as in vertical surfaces such as dados/skirting etc., set and jointed in neat cement slurry and in coloured cement to match Coloured on including plaster (backing coat) 1:4 Cement Mortar 10mm thick, complete all as specified and directed by Engineer-in-Charge. |
| 39 | Material & Labour for rounding to edges of granite stone slabs one edge such as in counter type WHB platform etc. to the entire satisfaction of Engineer-in-Charge. |
| 40 | Demolition of cement concrete in ground floor and paving not exc 15cm thickness (below or above ground level), complete all as specified and directed by Engineer-in-Charge. |
| 41 | Material & Labour for 75mm thick PCC 1:3:6 type C-2 using 40mm graded aggregate as in plinth protection finishing even & fair without using extra cement laid in bays with construction, 6mm thick joints should be filled with bitumen mastic filling comprising of one part of heated bitumen 80/100 gde and three part of sand (all by weight), complete all as specified and directed by Engineer-in-Charge. |
| 42 | Taking down chowkhats or frame (with shutter w/o taking off shutter from the frame) area not exceeding 1.5 Sqm each, complete all as specified and directed by Engineer-in-Charge. |
| 43 | Taking down chowkhats or frame (with shutter w/o taking off shutter from the frame) area exceeding 1.5 Sqm but not exceeding 4 sqm each, complete all as specified and directed by Engineer-in-Charge. |
| 44 | Supply & Fixing pressed steel door frame 105 x 60mm with one or more rebated including necessary fixing lugs hinges, lock stick, etc., complete all as specified and directed by Engineer-in-Charge. |
| 45 | Supply & Fixing Pressed steel frames of size 125 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed by Engineer-in-Charge. |
| 46 | Material & Labour for PCC 1:3:6 type C-1 using 20mm graded stone aggregate as in filling of pressed steel door frame, complete all as specified and directed by Engineer-in-Charge. |
| 47 | Supply & Fixing 40mm thick flush shutters solid core construction with block board core and plywood face panels, commercial type on both sides decorative face veneer with lipping/frame to match supplied and fitted to chowkats, complete all as specified and directed by Engineer-in-Charge. |
| 48 | Supply & Fixing 35mm thick 2nd class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc., size of members of shutters as specified in SSR Part -I, section 8, clause 8.24 (a) complete all as specified and as directed. fitted to chowkhats for doors etc., complete all as specified and directed by Engineer-in-Charge. |
| 49 | Supply & Fixing PVC door frame size 50mm x 47mm made out of 5mm plain coloured PVC sheet reinforced with MS square tube supplying & fixing in opening as per specification, complete all as specified and directed by Engineer-in-Charge. |
| 50 | Supply & Fixing factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rails, lock rails and bottom rails on either side and as gap insert for top rail and bottom rail Panelling of plain colour PVC sheet to be fitted in the M.S frame welded /sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement, supplying and fixing in the frame at site as per specification and drawing, complete all as specified and directed by Engineer-in-Charge. |
| 51 | Supply & Fixing aluminium anodised, barrel tower bolts of extruded section with length of bolt 200mm and fixed, complete all as specified and directed by Engineer-in-Charge. |
| 52 | Supply & Fixing aluminium anodised, barrel tower bolts of extruded section with length of bolt 150mm and fixed, complete all as specified and directed by Engineer-in-Charge. |
| 53 | Supply & Fixing aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy with length of bolt 300 mm and fixed, complete all as specified and directed by Engineer-in-Charge. |
| 54 | Supply & Fixing 100mm butt hinges extruded aluminium alloy with galvanised mild steel hinge pin, Type-B-21, complete all as specified and directed by Engineer-in-Charge. |
| 55 | Supply & Fixing continuous (piano) hinges, mild steel bright finish or electro-galvanised, width of flaps 30mm, complete all as specified and directed by Engineer-in-Charge. |
| 56 | Supply & Fixing extruded aluminium alloy handles, fabricated type, anodised of size 150mm, complete all as specified and directed by Engineer-in-Charge. |
| 57 | Supply & Fixing extruded aluminium alloy handles, fabricated type, anodised of size 125mm, complete all as specified and directed by Engineer-in-Charge. |
| 58 | Supply & Fixing 150mm long floor door stopper of aluminium alloy body and tongue with hard drawn steel spring, complete all as specified and directed by Engineer-in-Charge. |
| 59 | Supply & Fixing 300mm long mild steel ordinary rat tail rod pattern springs, including roller and roller plate, complete all as specified and directed by Engineer-in-Charge. |
| 60 | Supply & Fixing 125mm hasp and staples, aluminium anodized including bolt to hinges plate and fixed with screws, complete all as specified and directed by Engineer-in-Charge. |
| 61 | Supply & Fixing stainless steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with stainless steel wire staple/ wooden beads, complete all as specified and directed by Engineer-in-Charge. |
| 62 | Material & Labour for 9mm thick pre-laminated particle board interior grade, pre-laminated both sides with decorative choice laminations fixed with screw to timber/steel frame work as in repair, complete all as specified and directed by Engineer-in-Charge. |
| 63 | Material & Labour for 18/19mm thick pre-laminated particle board interior grade, pre-laminated both sides with decorative choice laminations fixed with screw to timber/steel frame work as in repair, complete all as specified and directed by Engineer-in-Charge. |
| 64 | Supply and fixing factory made uPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50mm mullion 47 x 68mm both having wall thickness of 1.9 ± 0.2mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Glass shall be paid separately). |
| 65 | Providing and fixing factroy made uPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (±0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2 ±0.2mm thick galvanised steel Frame (30mm x 18mm) 2 Nos, sliding sash (30mm x 18mm, sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories.(Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured for payment purpose.)Area not exceeding 2.00 Sqm |
| 66 | Providing and fixing factory made uPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (±0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2 ±0.2mm thick galvanised steel Frame (30mm x 18mm) 2 Nos, sliding sash (30mm x 18mm, sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories.(Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured for payment purpose.)Area exceeding 2.00 Sqm |
| 67 | Supply & Fixing 4mm thick, plain, tinted glass area exceeding 0.50 sqm each pane fixed in windows/ Ventilators, including glazing clips and beading, complete all as specified and directed by Engineer-in-Charge. |
| 68 | Supply & Fixing 12mm thick Toughened Glass Door with patch fittings with cover plate of SS-316 Grade including Decorative type Stainless steel 316 grade floor Spring, fixing/moving arrangement at top, designer glass handles 2 Nos of 450mm suitable size as directed, Fin Connect Patch Lock etc., in each door, including designer glass film/sticker on glass, cutting holes in any size in floor and wall, complete all as specified and directed by Engineer-in-Charge. |
| 69 | Supply & Fixing 12mm thick Toughened Glass as in Partition with patch fittings with cover plate of SS-314 Grade, necessary accessories etc., including 3D/designer glass film/sticker on glass, cutting holes in any size in floor and wall, complete all as specified and directed by Engineer-in-Charge. |
| 70 | Supply & Fixing aluminium hat & coat hooks solid body 125mm to 175mm fixed with brass screw, complete all as specified and directed by Engineer-in-Charge. |
| 71 | Supply & Fixing MS Peg set of six powder coated as approved by GE, complete all as specified and directed by Engineer-in-Charge. |
| 72 | Material & Labour for mild steel pipe 25mm dia Drapery rod fancy type with PVC coating fixed in the MS hooks, and finials/side brackets (both side), shade as approved by GE, complete all as specified and directed by Engineer-in-Charge. |
| 73 | Material & Labour for Cutting holes in brick walls in exceeding half brick and not exceeding one brick in cement in mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1, complete all as specified and directed by Engineer-in-Charge. |
| 74 | Material & Labour for treating small article such as stops, covers, gully, gratings and hold fast ends & post backs of chowkhat etc., with creosote oil, tarred area not exceeding 0.10 Sqm each, complete all as specified and directed by Engineer-in-Charge. |
| 75 | Material & Labour for Preparation of newly steel surface of any description over 10 cm width or girth and applying two coats of synthetic enamel paint, complete all as specified and directed by Engineer-in-Charge. |
| 76 | Material & Labour for Preparation of newly wooden surface of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed by Engineer-in-Charge. |
| 77 | Taking down old steel tubing/CPVC Pipe & connection including cleaning for re-fixing for 15mm bore pipe, complete all as specified and directed by Engineer-in-Charge. |
| 78 | Taking down old steel tubing/ CPVC Pipe & connection including cleaning for re-fixing for 20mm bore pipe, complete all as specified and directed by Engineer-in-Charge. |
| 79 | Supply & Fixing of CPVC pipes, 20mm dia SDR-11, including plain CPVC SDR fittings for Hot/ cold water for sizes mentioned below including all fittings and solvents and special fittings like brass tee, make threaded brass adaptor, female threaded brass adaptor etc., unions, flange and tank adapter all as per manufacturers recommendations, complete all as specified and directed by Engineer-in-Charge. |
| 80 | Supply & Fixing of CPVC pipes, 25mm dia SDR-11, including plain CPVC SDR fittings for Hot/ cold water for sizes mentioned below including all fittings and solvents and special fittings like brass tee, make threaded brass adaptor, female threaded brass adaptor etc., unions, flange and tank adapter all as per manufacturers recommendations, complete all as specified and directed by Engineer-in-Charge. |
| 81 | Cutting chases in brick walls, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exceeding 10 cm girth, complete all as specified and directed by Engineer-in-Charge. |
| 82 | Supply & Fixing in repairs Stop valve / Angle valve fancy type cast copper alloy chromium plated screwed down high pressure with capstan heads screwed both ends for iron pipe or for union and fixed 15mm bore, complete all as specified and directed by Engineer-in-Charge. |
| 83 | Supply & Fixing in repairs 15mm bore bib tap cast copper alloy, chromium plated, long body fancy type with capstan headed, screwed down, screwed for iron pipe, complete all as specified and directed by Engineer-in-Charge. |
| 84 | Supply & Fixing in repair 15mm dia pillar tap cast copper alloy chromium plated capstan head screwed down high pressure with or without lettered hot or cold with long screw shank and fly nutt screw for iron pipe, complete all as specified and directed by Engineer-in-Charge. |
| 85 | Supply & Fixing in repair for 15mm chromium plated brass wall mixer fancy type swan neck long nose- screwed down high pressure with or without lettered hot and cold and flynuts 15 mm dia., complete all as specified and directed by Engineer-in-Charge. |
| 86 | Supply & Fixing in repair Stainless steel sink with draining board, made out of 1.00mm thick sheet for kitchen or laboratory with plug, washers waste pipe, cast iron cantilever brackets, connecting union overall Size 915mm x 460mm with bowl size 410mm x 330mm x 160mm, complete all as specified and directed by Engineer-in-Charge. |
| 87 | Supply & Fixing in repair Stainless steel plate rack of size 60 x 90 cm with suitable shelves/rack rectangular wall mounted with necessary fixing arrangement, complete all as specified and directed by Engineer-in-Charge. |
| 88 | Supply & Fixing in repairs Soap dish, stainless steel approx size 160mm x 160mm x 90mm, complete all as specified and directed by Engineer-in-Charge. |
| 89 | Material & Labour for 32mm bore low density polyethylene pipes (LDPE) with fittings of pressure rating 6 Kgf / Sqcm fixed to walls or in floors etc., complete all as specified and directed by Engineer-in-Charge. |
| 90 | Supply & Fixing in repair PVC connection 450mm long, 15mm size with PTMT nuts, complete all as specified and directed by Engineer-in-Charge. |
| 91 | Supply & Fixing in repairs grating doom 125mm dia PTMT with waste hole (Min weight 40 grms), complete all as specified and directed by Engineer-in-Charge. |
| 92 | Supply & Fixing in repairs chromium plated shower rose 125mm size and 15mm dia with or without swivel joints including fixing to pipe and union, complete all as specified and directed by Engineer-in-Charge. |
| 93 | Supply & Fixing in repair 600mm x 450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board of commercial ply wood and fixed to wooden plugs with chromium plated brass screws and cup washers, complete all as specified and directed by Engineer-in-Charge. |
| 94 | Supply & Fixing in repairs Towel rail 600mm long and 20mm dia brass chromium plated D type fixed with screws and wooden or plastic cleats, complete all as specified and directed by Engineer-in-Charge. |
| 95 | Supply & Fixing in repair vitreous china wash down water closet pan Pedestal pattern white excluding fixing bolts, flushing cistern and flush pipe with and including 'P' or 'S' trap and making good to floor to match with existing, complete all as specified and directed by Engineer-in-Charge. |
| 96 | Supply & Fixing in repairs 10 ltr PVC valve less symphonic action type flushing cistern, low level white with inlet ball valve float and handle with flush pipe, complete all as specified and directed by Engineer-in-Charge. |
| 97 | Supply & Fixing in repairs Vitreous China wash hand basin, white, flat back, size 550mm x 400mm including brass coupling, mild steel brackets fixed to wall, with pedestal, complete all as specified and directed by Engineer-in-Charge. |
| 98 | Supply & fixing toilet paper holder with flat recessed type stainless steel, fixed as in repairs, complete all as specified and directed by Engineer-in-Charge. |
| 99 | Supply & Fixing in repair, Health faucet (ABS body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position, complete all as specified and directed by Engineer-in-Charge. |
| 100 | Supply & Fixing CP waste fittings brass chromium plated for sink 32mm dia with long screws sinks and fly nuts, flanges end bedded in red led cement and other in fixed, complete all as specified and directed by Engineer-in-Charge. |
| 101 | Supply & Fixing CP waste fittings brass chromium plated for sink 40mm dia with long screws sinks and fly nuts, flanges end bedded in red led cement and other in fixed, complete all as specified and directed by Engineer-in-Charge. |
| 102 | Material & Labour for 75mm dia., PTMT multi floor trap plain with grating including jointing with solvent cement, complete all as specified and directed by Engineer-in-Charge. |
| 103 | Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan necks etc. including cleaning or re-fixing or removal to store, complete all as specified and directed by Engineer-in-Charge. |
| 104 | Supply & Fixing 110mm dia PVC (SWR ) pipes Single socketed in any length with rubber rings joints fixed to walls, complete all as specified and directed by Engineer-in-Charge. |
| 105 | Supply & Fixing PVC (SWR) pipes 75mm bore single socketed in any length with rubber ring joints laid in floors, trenches, complete all as specified and directed by Engineer-in-Charge. |
| 106 | Supply & Fixing 110mm dia PVC (SWR) branches piece, double (double Y) equal or unequal with access door rubber rings joints fixed to walls, complete all as specified and directed by Engineer-in-Charge. |
| 107 | Supply & Fixing PVC (SWR) branch pieces, single (equal or un equal), ordinary or inverted (spigot or socket type) or with parallel branches of 110mm dia with access door, complete all as specified and directed by Engineer-in-Charge. |
| 108 | Supply & Fixing 110mm dia PVC (SWR) bends any radius with access door, complete all as specified and directed by Engineer-in-Charge. |
| 109 | Supply & Fixing 75mm dia PVC (SWR) bends any radius with access door, complete all as specified and directed by Engineer-in-Charge. |
| 110 | Supply & Fixing 110mm bore PVC (SWR) vent cowl including jointing with solvent cement, complete all as specified and directed by Engineer-in-Charge. |
| 111 | Material & Labour PVC (SWR) Tee of 110mm dia with access door etc., complete all as specified and directed by Engineer-in-Charge. |
| 112 | Material & Labour PVC (SWR) Tee of 75mm dia access door etc., complete all as specified and directed by Engineer-in-Charge. |
| 113 | Supply & Fixing PVC (SWR) gully trap 125 x 110mm setting and jointing with solvent cement, complete all as specified and directed by Engineer-in-Charge. |
| 114 | Supply & Fixing stack clamps out of 50mm by 5mm flat iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100mm bore etc., complete all as specified and directed by Engineer-in-Charge. |
| 115 | Dismantling water tanks exceeding 500 and not exceeding 1000 ltr capacity, complete all as specified and directed by Engineer-in-Charge. |
| 116 | Supply & Fixing 1000 ltrs rotational moulded polythine water storage tanks (cylinder vertical with closed top) hoisted and fixed in position including ball brass valves, high pressure with polythene float and flynut complete screw for iron pipe or brass ferrule all as specified in SSR Part-I, complete all as specified and directed by Engineer-in-Charge. |
| 117 | Disconnecting existing tanks of capacity 500 ltr to 1000 ltr, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position, complete all as specified and directed by Engineer-in-Charge. |
| 118 | Supply & Fixing 20mm bore ball valve high pressure PTMT with epoxy coated aluminium rod & high density polythene float ball and fly nut screwed for iron pipe, complete all as specified and directed by Engineer-in-Charge. |
| 119 | Supply & Fixing 25mm dia gun metal, globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed, complete all as specified and directed by Engineer-in-Charge. |
| 120 | Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement, complete all as specified and directed by Engineer-in-Charge. |
| 121 | Roughening surfaces of old concrete floor/terrace by picking including taking down existing detoriated / decayed tar felt PCC tiles or any type of treatment including loose surface, scraping with scraper, chiselling, scraping of surface with wire brush or any other method, sweeping clean & washing down with water to remove dust etc. and removing the scraped materials debris to a distance not exc. 50 m, complete all as specified and directed by Engineer-in-Charge. |
| 122 | Material & Labour for wire brushing and cleaning top surface of tiles, lime terracing or cement concrete, including flashing and junction of parapet, etc., and surface painting with a layer of blown bitumen of any penetration applied hot @1.70 kg per sqm. Blinded with grit or pea size gravel @ 0.006 cum per sqm and lightly tampered (area of flashing etc. shall be added to the roof area, complete all as specified and directed by Engineer-in-Charge. |
| 123 | Material & Labour for 10mm thick screed bed or bedding layer in Cement Mortar 1:3 mixed with water proofing compound @ 3 % by weight of cement on concrete roof surface finished fair and even to maintain the proper slope of roof surface etc., complete all as specified and directed by Engineer-in-Charge. |
| 124 | Material & Labour for Providing water proofing treatment over cleaned roof surface with super thermo APP modified water proofing membrane comprising of the following for roofs- |
| 125 | Cleaning of plastered roof surfaces and applying a coat of bitumen primer @ 0.30 kg/Sqm on top of dry surface of finished cement mortar plaster, complete all as specified and directed by Engineer-in-Charge. |
| 126 | One coat of hot blown bitumen of grade 85/25 @ 1.2kg /sqm shall be applied over primed surfaces, complete all as specified and directed by Engineer-in-Charge. |
| 127 | One layer of APP based polymeric water proofing membrane of weight not less than 3 kg/Sqm consisting 3mm thick reinforced with polyester non wove fabric shall be unrolled surfaces with lap of 100mm and the overlap shall be sealed by flame, complete all as specified and directed by Engineer-in-Charge. |
| 128 | Applying two coats of aluminium paint on top of membrane @ 0.10Kg/Sqm, complete all as specified and directed by Engineer-in-Charge. |
| 129 | Material & Labour for 20mm thick Screed bed or bedding layer of cement mortar 1:4, complete all as specified and directed by Engineer-in-Charge. |
| 130 | Supply & Fixing cement concrete tiles size 25cmx25cmx22mm thick machine cut pressed set jointed and pointed in neat cement slurry with grey cement and pigments in floors and cut and polished, complete all as specified and directed by Engineer-in-Charge. |
| 131 | Bitumastic gola, with 80/25 bitumen and coarse sand mixture, 1:3 by weight, 8cmx8cm at the junction of roofing to vertical surfaces, complete all as specified and directed by Engineer-in-Charge. |
| 132 | Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3, complete all as specified and directed by Engineer-in-Charge. |
| 133 | Schedule 'A' E/M |
| 134 | Taking down carefully aluminium/copper point wiring (light, fan, socket or power) concealed and casing capping complete including fittings and fixtures such as switches, ceiling roses, pendants, regulators, sockets light fittings and making good the disturbed surfaces of walls/ceiling/floor etc., complete all as specified and directed by Engineer-in-Charge. |
| 135 | Disconnecting of unserviceable sub main wiring of any size and including steel conduit and accessories & removing from site and making good the disturbed surfaces, complete all as specified and directed by Engineer-in-Charge. |
| 136 | Disconnecting electric connections and taking down old unserviceable MCB SPN/SP/TP and DB's of any capacity, complete all as specified and directed by Engineer-in-Charge. |
| 137 | Material & Labour for Point wiring complete with 1.5 sqmm single core PVC insulated but unsheathed multi-stranded copper conductor FRLS cable 650/1100 Volts grade drawn through and including non-metallic rigid PVC heavy duty concealed conduit (minimum 20mm dia external) but shall be increased as per actual site requirement in accordance with clause 19.125 of SSR part- I ISI marked with wall thickness not less than 1.8mm including conduit accessories like bends, tees, junction boxes etc fixed concealed/ recessed in wall or ceiling etc., including 1.5 sqmm PVC insulated but unsheathed multi-stranded copper conductor FRLS cable as earth continuity wire including modular type metal flush box with cover plate and frame of required modules for mounting of modular switches, sockets, switch sockets, fan regulators with required modules all as specified etc for the following:- |
| 138 | One light /fan point controlled by one, one way switch |
| 139 | One 3 pin 6 Amps socket outlet on same board |
| 140 | One 3 pin 6 Amps socket outlet on independent board. |
| 141 | Material & Labour for Point wiring complete with 2.5 Sqmm single core PVC insulated but unsheathed multi-strand copper conductor FRLS cable 650/1100 Volts grade conforming to IS-694 drawn through PVC conduit (minimum 20mm dia (external) but shall be increased as per actual site requirement in accordance with clause 19.125 of SSR Part I) ISI marked with wall thickness not less than 1.8mm heavy duty including conduit accessories concealed pressed steel terminal boxes of size cover white/coloured including 2.5 Sqmm PVC insulated but unsheathed copper conductor FRLS cable as earth continuity wire for one 3 pin 15 or 16 Amps socket outlet on independent board, including modular type metal flush box with cover plate and frame of required module for mounting of modular switches, sockets, switch sockets with required modules, complete all as specified and directed by Engineer-in-Charge. |
| 142 | Supply & fixing modular switch 1 way, 6 Amps, 1 module (ISI marked), complete all as specified and directed by Engineer-in-Charge. |
| 143 | Supply & fixing modular switch 1 way, 16 Amps, 1 module (ISI marked), complete all as specified and directed by Engineer-in-Charge. |
| 144 | Supply & fixing modular socket, 6 Amps, 2/3 pin combined 2 module (ISI marked), complete all as specified and directed by Engineer-in-Charge. |
| 145 | Supply & fixing modular socket, 6/16 Amps, 2/3 pin combined 2 module (ISI marked), complete all as specified and directed by Engineer-in-Charge. |
| 146 | Supply & fixing modular fan regulator, 120 watt, 2 module (ISI marked), complete all as specified and directed by Engineer-in-Charge. |
| 147 | Supply & fixing ceiling rose, surface Bakelite, 65 x 17 mm three terminals (ISI Marked), complete all as specified and directed by Engineer-in-Charge. |
| 148 | Supply & fixing in repalcement of wall mounted LED Tube light fitting 1 x 20W LED (6500K), 4 feet, Sleek and seamless profiled extruded aluminium batten with an efficient diffuser to illuminate work, including making connections with 2 core flexible copper wire 0.50 Sqmm from ceiling rose after fixing fitting, complete all as specified and directed by Engineer-in-Charge. Make:- Wipro - CAT PT No- LL20-281-XXX-65AL1** or equivalent to Bajaj/Havells or equivalent make mentioned in Appendix ‘B’. |
| 149 | Supply & fixing in repalcement of wall mounted LED Tube light fitting 1 x 10W LED (6500K), 2 feet, Sleek and seamless profiled extruded aluminium batten with an efficient diffuser to illuminate work, including making connections with 2 core flexible copper wire 0.50 Sqmm from ceiling rose after fixing fitting, complete all as specified and directed by Engineer-in-Charge. Make:- Wipro - CAT PT No- LL20-111-XXX-65NE3* or equivalent to Bajaj/Havells or equivalent make mentioned in Appendix ‘B’. |
| 150 | Supply & fixing in repalcement of LED wall light 2x 6 Watts (2700K) and including connected with 2 core flexible copper wire 0.50 Sqmm from ceiling rose after fixing fitting in position at site, complete all as specified and directed by Engineer-in-Charge. Make:- Wipro Code No DW31227/ Philips/Havells /CG or equivalent make mentioned in Appendix ‘B’. |
| 151 | Supply & fixing in repalcement of LED 25 Watts (5700K) Bldg Security light fitting, and including with GI Pipe 32mm dia bracket with connected with 2 core flexible copper wire 0.50 Sqmm from ceiling rose after fixing fitting in position at site, complete all as specified and directed by Engineer-in-Charge. Make:- Wipro Cat No LR02-291-XXX-57-XX /Philips / Havells /CG or equivalent make mentioned in Appendix ‘B’. |
| 152 | Supply & fixing BEE five star rated BLDC energy efficient high-speed ceiling fan having 1200mm blade sweep, air-flow not less than 210 CMM, operating voltage 220-240 V and frequency 50 Hz, including a downroad of suitable size and electrical connection with 3 core flexible Cu conductor cable of appropriate size from ceiling rose to the fan, complete all as specified and directed by Engineer-in-Charge. |
| 153 | Supply & fixing energy efficient metallic exhaust fan having blade sweep 300mm, air delivery not less than 900 CMH, operating voltage 220-240 V and frequency 50 Hz, including electrical connection with 3 core flexible Cu conductor cable of appropriate size from ceiling rose to the fresh-air fan, complete all as specified and directed by Engineer-in-Charge. Make:- Crompton Cat-Part No. Transair Reversible or equivalent model of Havells/ Orient or equivalent make mentioned in Appendix ‘B’. |
| 154 | Supply & fixing AC Single phase meter Two wire tamper proof static meter of Class 1.0, 240 V 50Hz basis current 10-60A with optical port + box conforming to IS-13779 and relevant IEC standards within built Low Power Radio Frequency (LPRF) communication facility in Cyantech or equivalent Mesh network with default and no demand display, billing data generation facility anti tamper features microprocessor and LED/LCD based circuitry, complete all as specified and directed by Engineer-in-Charge. Make L&T, HPL, Secure or equivalent make mentioned in Appendix ‘B’. |
| 155 | Supply & fixing distribution Board cum Meter box wall mounting type of size 680mm x 1254mm x 365mm (minimum) fabricated from polycarbonate sheet, IP 54 compartmentalised design, Cable gland of suitable size prewired and comprising of following :-(a) MCCB cap 63 Amps, 4 Pole, 25 KA - 01 No.(In Coming)(b) MCB SPN 40 Amp, 10 KA - 07 Nos (Out Going)(c) Terminal for distribution (d) 06 Nos of cubical for housing single phase meter all as specified and as directed. Make Hensel/Hager/Universal or equivalent make mentioned in Appendix ‘B’. |
| 156 | Supply & fixing electric water heater, storage type with inner tank and heating element upto 2 KW capacity 25 litre, BEE 4 star and above rated complete with all accessories such as safety valve, thermostat, NRV, with Anchor fasteners of suitable size and including Flexible hot/cold connection Pipe -02 Nos, complete all as specified and directed by Engineer-in-Charge. Make - JAQUAR Model. ELENA MANUAL 25 LTR/ Racold Model. Andris Uno 25/AOSmith Model. Finesse or equivalent make mentioned in Appendix ‘B’. |
| 157 | Material & Labour for sub main wiring with two single core 2 x 4 Sqmm PVC (FRLS) insulated multi-stranded flexible copper conductor cable 660/1100 volts grade down in through including Concealed PVC Conduit with all accessories, PVC insulated 1x 2.5 Sqm single core single strand copper conductor as continuous earth wire in green colour connected to common earth dolly, complete all as specified and directed by Engineer-in-Charge. Note : 1. Two runs of cable, one run of earth wire, one run of PVC conduit will be measured and paid one unit. |
| 158 | Material & Labour for sub main wiring with two single core 2 x 6 Sqmm PVC (FRLS) insulated multi-stranded flexible copper conductor cable 660/1100 volts grade down in through including Concealed PVC Conduit with all accessories, PVC insulated 1 x 4 Sqm single core single strand copper conductor as continuous earth wire in green colour connected to common earth dolly, complete all as specified and directed by Engineer-in-Charge. Note : 1. Two runs of cable, one run of earth wire, one run of PVC conduit will be measured and paid one unit. |
| 159 | Supply & fixing of MCB DB 12 way SPN, double door, vertical type, IP - 53 with 200 Amps rated bus bar, Concealed and connecting up, complete all as specified and directed by Engineer-in-Charge. |
| 160 | Supply & fixing of MCB SPN, 240 volt, 32 Amps, complete all as specified and directed by Engineer-in-Charge. |
| 161 | Supply & fixing of MCB SP, 240 volt, 6 to 32 Amps, complete all as specified and directed by Engineer-in-Charge. |
| 162 | Supply & fixing earthed metal plug socket outlet with earthed plug top 20 Amps capacity with sheet metal enclosure and one 20 Amps MCB SPN, complete all as specified and directed by Engineer-in-Charge. |
| 163 | Supply and laying of XLPE insulated and PVC armoured heavy duty 1100 volt grade electric LT UG cable with aluminium conductor of size 50 Sqmm 3.5 Core laid in trenches/along the wall/pole including making good the disturbed surfaces of walls/floor etc., and taking down old unsv cable, complete all as specified and directed by Engineer-in-Charge. |
| 164 | Excavation in trenches not exceeding 1.5 Metre wide and not exceeding 1.5 Metre in depth and getting out Soft/ Loose soil, complete all as specified and directed by Engineer-in-Charge. |
| 165 | Returning filling in including spreading levelling watering and well Ramming in layers not exceeding 25 cm thick, complete all as specified and directed by Engineer-in-Charge. |
| 166 | Removing excavated material not exceeding 50 Metre and depositing where directed at a level not exceeding 1.5 Metre above the starting point, complete all as specified and directed by Engineer-in-Charge. |
| 167 | Supply & Fixing of GI steel tubing light grade 32mm dia for laying in ground and road crossing along the pole in coping etc., for cable protection including necessary fittings, clamps for supports, etc., including making good the disturbed surfaces of walls/floor etc., complete all as specified and directed by Engineer-in-Charge. |
| 168 | Supply and laying 50 /38mm Double Walled Corrugated (DWC) Pipes having corrugation on the outer wall and plain surface on the inner wall confirming to IS14930 (Part-II) for protection of UG cables, laid in trenches/ road/ drain or fixed along wall, poles or laid under floor, complete all as specified and directed by Engineer-in-Charge. Make : Rex / Poly/ Gemini |
| 169 | Material & Labour for cutting existing road/hard standing not exc 45 x 45 cm in wide & depth getting out excavated material for laying cable/GI tube, returning filling & well ramming watering finish surface 10 cm from top using PCC 1:3:6; including removal of surpluses soil, complete all as specified and directed by Engineer-in-Charge. |
| 170 | Material & Labour for bore Earthing complete with galvanised steel pipe electrode, 40mm bore, medium grade, 2.5 metres length, buried directly and preferably vertically in ground with top edge not less than 1.25 metres below ground level connected with Earthing lead of 4mm dia galvanised iron or steel wire all as shown in Plate No. 2 to the Earthing test point all as specified and indicated including testing on completion, complete all as specified and directed by Engineer-in-Charge. |
| 171 | Supply, laying and jointing CPVC Pipe of SDR 11 of 40mm bore with all fittings in any lengths with screwed and socket joints, together with all galvanised steel fitting such as sockets, elbows, bends, tees, reducers, unions, cap plugs, nipple, short pieces etc., fixed complete by means of and including clips, wall hook etc or laid in trenches, Including taking down old unsv GI Pipe, complete all as specified and directed by Engineer-in-Charge. |
| 172 | Supply & Fixing CPVC ball valve of 40mm dia with wheel head screwed both ends for iron pipes, complete all as specified and directed by Engineer-in-Charge. |
| 173 | Material & Labour for cutting of existing DI/CI Pipe in position for inserting CI Tee complete with 50/80/100 mm dia union, nipple, etc all as directed for taking 40 mm cpvc branch line, complete all as specified and directed by Engineer-in-Charge. |
| 174 | Material & Labour for Construction of new valve chamber of size 600 x 600 x 600mm including necessary earth work in any type of soil, PCC foundation C-2 1:3:6 in base concrete, brick work in Cement Mortar 1:6 with 10mm thick plaster internally and 15mm thick externally in Cement Mortar 1:4, 6mm thick MS cover with hinges and locking arrangement fixed to angle iron frame made-out of 40 x 40 x 6mm MS angles complete with 2 coats of synthetic enamel paint over one coat of red oxide zinc chrome primer on all metal works & two coats of white wash on all plastered surfaces of valve chambers, complete all as specified and directed by Engineer-in-Charge. Please Enable Macros to View BoQ information |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
