|
| 1 | Dismantling of existing structures like culverts, bridges, retaining walls, CC road and other structure comprising of masonry, cement concrete, wood work, steel work, including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead of 50 metres as directed by Engineer.Lime Concrete, cement concrete grade M-10 (1:5:10) and below |
| 2 | Brick work with FPS bricks of class designation 75 in foundation and plinth in: Cement mortar 1:6 (1 cement :6 coarse sand) |
| 3 | Half brick masonry with FPS bricks of class designation 75 in superstructure above plinth level upto two stories. Cement mortar 1:4 (1 cement :4 coarse sand) |
| 4 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new work |
| 5 | Cement plastering including T&P, scaffolding, material and complete labour, including cost of water, curing, racking of joints etc. with 12 mm cement plaster of mix : including Providing /mixing of synthetic fibers compulsorily complying with IS 16481:2022 of 06 mm/12 mm length to be mixed @ 0.25% by weight of Cement i.e. 125 gms per 50 kg Cement up to 900 gms per cum of Concrete/ mortar 1:6 (1 cement : 6 fine/ coarse sand) |
| 6 | Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work |
| 7 | P & F indian type white glazed viterous china 1st quality W.C. orissa pan (I.S:2556 Mark) kwith 100 m vitreouts china P or S trap including cutting and making good the wall and floor. Size 580 x 440 mm |
| 8 | Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including base coat of water proofing cement paint applied @ 2.20kg/10 sqm. |
| 9 | SS wire gauge with average width of aperture 1.4 mm on bothdirections with wire of dia 0.63 mm |
| 10 | Structural steel work riveted, bolted or welded in built up sections,trusses and framed work, including cutting, hoisting, fixing in positionand applying a priming coat of approved steel primer all complete: |
| 11 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement - All work upto plinth level : 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20mm nominal size) |
| 12 | Centring and shuttering with plywood or steel sheet upto two stories or height upto 7.5 metre above plinth level including strutting,propping etc. and removal of form for : Lintels, beams, plinth beams, girders, bressumers and cantilevers. |
| 13 | Columns, Pillars, Piers, Abutments, Posts and Struts. |
| 14 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets,columns, pillars, piers, abutments, posts and struts etc. upto two stories excluding cost of centring, shuttering, finishing and reinforcement : 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20mm nominal size) |
| 15 | Random rubble masonry with hard stone in foundation and plinth Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 16 | Extra for random rubble masonry with hard stone in superstructureabove plinth level and upto two stories. |
| 17 | Reinforcement for R.C.C. work at all levels including straightening,cutting, bending, placing in position and binding all complete. Cold twisted bars |
| 18 | Providing and fixing white vitreous china wash basin includingmaking all connections but excluding the cost of fittings :Angle back wash basin of size 400x400mm |
| 19 | Providing and fixing 1st quality MAT finished ceremic tile size 300x300mm confirming to IS : 13755 and IS : 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (including the cost of cement mortar bed 1:4). |
| 20 | Providing and fixing 1st quality ceramic glazed vitrified tiles of colour standard white, grey, ivory, fume, red brown, light green, light blue, and other light shades with water absorbtion less than or equal to 0.08% confirming to IS : 13753 & IS : 15622 in floor, steps etc laid on bed on neat cement slury finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the the cost of cement plaster on wall and pillar) size 600mm x 600mm |
| 21 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitablelocking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank |
| 22 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 15 mm nominal bore. |
| 23 | Providing and fixing brass stop cock of approved qualit 15 mm nominal bore. |
| 24 | 110 mm ID/ND PVC-U pipes (stiffness class SN 8) as per IS 15328 |
| 25 | 110 mm dia U-PVC double/ single socketed 90° bend (class III, 6kg/sqcm) confirming to IS:7834 |
| 26 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work including cutting chases and making good the walls etc.,(A)15 mm nominal outer dia .Pipes |
| 27 | (B)20 mm nominal outer dia .Pipes |
| 28 | Granite stone of any colour and shade. |
| 29 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVC/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-incharge . (Cost of aluminium snap beading shall be paid in basic item) : With float glass panes of 5.50 mm thickness |
| 30 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape 1500x450 mm |
| 31 | Providing and fixing PTMT Bottle Trap forWash basin and sink.Bottle trap 31mm single piece moulded with height of 270mm, effective length of tail pipe 260mm from the centre of the waste coupling 77mm breadth with 25mm minimum water seal, weighing not less than 260gms. |
| 32 | P.T.M.T. Bottle Trap 38/40MM |
| 33 | P&F of Heavy duty capacitor start 900/1400 RPM single phase ISI marked Exhaust fan,IS:2312 marked in existing opening including making connections testing etc. as required 300 mm sweep(900/1400 RPM) |
| 34 | Providing and fixing external grade board solid core single leaf flushdoor shutters ISI 2202-67 marked using Phenol formal dehyderesinin glue both sides including approved ISI marked Stainless Steel butthinges fittings with necessary screws complete as per annexure 'A' :Decorative teak veneer One side |
| 35 | Extra for Providing and fixing flush doors with decorative veneering on one side |
| 36 | Providing and applying plaster of paris putty of 2 mm thickness overplastered surface to prepare the surface even and smooth complete |
| 37 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply including allCPVC plain & brass threaded fittings i/c fixing the pipe with clampsat 1.00 m spacing. This includes jointing of pipes & fittings with onestep CPVC solvent cement and the cost of cutting chases andmaking good the same including testing of joints complete as perdirection of Engineer in Charge. Concealed work including cutting chases and making good the walls etc., 25 mm nominal outer dia .Pipes. |
| 38 | Providing and fixing PTMT 15 mm Urinal spreader size 95x69x100mm with 1/2\\" BSP thread and shapes. Weighing not less than 60gms. |
| 39 | Providng & fixing PTMT urinal cock of approved quality |
| 40 | Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass including painting of fittings and cutting and making good the walls and floors wherever required : Single half stall urinal with 5 litre P.V.C. automatic flushing cistern. |
| 41 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : White Vitreous China Surgeon type wash basin of size 660x460 mm with a pair of 15 mm C.P. brass pillar taps with elbow operated levers. |
| 42 | Making connection of GI Pipe distribution branch with GI main of following size. A. 32mm |
| 43 | B. 40mm nominal boare |
| 44 | Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball. 15 mm nominal bore, 105 mm long. Weighing not less than 138 gms. |
| 45 | Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor ISI marked (IS:694) of 1.1 kV grade and approved make in existing surface or recessed conduit/casing capping including making connections etc. as required. A. 2 x 1.5mm |
| 46 | B. 2 x 2.5 sqmm |
| 47 | Providing and fixing double bearing capacitor celling fan of approved make complete with regulator 1400mm sweep. |
| 48 | Providing and fixing aluminium work for doors, windows, ventilatorsand partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically whereverrequired including cleat angle, Aluminium snap beading for glazing /panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and panelling to be paid for separately) :For fixed portion. Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 49 | For shutters of doors, windows & ventilators including providing andfixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of PVC / neoprene gasket required (Fittings shall be paid for separately).Powder coated aluminium (minimum thickness of powder coating 50micron) |
| 50 | Providing and fixing 12mm thick Pre-laminated particle board flat pressed three layer or graded wood particle board conforming to IS:12823 Grade l Type ll, in panelling fixed in aluminium doors,windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side. |
| 51 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVC/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-incharge . (Cost of aluminium snap beading shall be paid in basicitem) With float glass panes of 5.50 mm thickness |
| 52 | Providing and fixing aluminium tubular handle bar 32 mm outer dia,3.0 mm thick & 2100 mm long with SS screws etc .complete as perdirection of Engineer-in-Charge. Anodized (AC 15 ) aluminium tubular handle bar |
| 53 | Providing and fixing 100mm brass locks (best make of approvedquality) for aluminium doors including necessary cutting and makinggood etc. complete. |
| 54 | Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2mm and braced with flat iron diagonals 20x5mm size with top and bottom rail of T-iron 40x40x6mm with 40mm dia,steel pulleys complete with bolts, nuts, locking arrangement,stoppers, handles, including applying a priming coat of approvedsteel primer. |
| 55 | Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq.mm FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) of approved make in surface / recessed ISI marked medium duty PVC conduit & it's accessories, round tiles,18 SWG M.S. box with earth terminal, screwless cage connectors for neutral looping in switch board & falce ceiling point, 6 A switch, 3.0 mm thick phenolic laminated sheet, zinc plated / brass screws, cup washers, making connections, testing etc. as required.(i) Short point (up to 3 mtr.) |
| 56 | (ii) Medium point (up to 6 mtr.) |
| 57 | (iii) Long point (up to 10 mtr..) |
| 58 | Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor ISI marked (IS:694) of 1.1 kV grade and approved make in existing surface or recessed conduit/casing capping including making connections etc. as required.(l)1 x 1.5 sq.mm |
| 59 | (ll)1 x 2.5 sq.mm |
| 60 | (lll)2 x 2.5 sq.mm |
| 61 | (ll)2 x 4.0 sq.mm |
| 62 | Wiring of 3 pin 5 amp. light plug point with 1.5 sq. mm FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq.mm FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade(IS:694) of approved make in surface / recessed ISI marked medium duty PVC conduit & it's accessories, 18 SWG M.S. box with earth terminal, screwless cage connectors for neutral looping in switch board & falce ceiling point, 6 A switch, 6 A socket, 3.0 mm thick phenolic laminated sheet, zinc plated / brass screws, cup washers, making connections, testing etc. as required. On board(I) Short point (up to 3 mtr.) |
| 63 | (II) Medium point (up to 6 mtr.) |
| 64 | (III) Long point (up to 10 mtr..) |
| 65 | Wiring of 3 pin 6 amp. Light plug point with 1.5 sq. mm FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq.mm FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade(IS:694) of approved make in surface / recessed ISI marked steel conduit & it's accessories, 18 SWG M.S. box with earth terminal, screwless cage connectors for neutral looping in switch board & false ceiling point, 6 A switch, 6 A socket, 3.0 mm thick phenolic laminatedsheet, zinc plated / brass screws, cup washers, bushes, check nuts, making connections, testing etc. as required.(I) Short point (up to 3 mtr.) |
| 66 | (II) Medium point (up to 6 mtr.) |
| 67 | (III) Long point (up to 10 mtr..) |
| 68 | Wiring of 6 pin 15 amp. Light power point with 4.0 sq. mm PVC insulated unsheathed solid / stranded copper conductor 1.1 kV grade of approved make in surface / recessed ISI marked pvc conduit & it's accessories, 18SWG M.S. box with earth terminal, screwless cage connectors for neutral looping in switch board , 15 A switch, 15 A socket, 3.0 mm thick phenolic laminated sheet, zinc plated / brass screws, cup washers, bushes, check nuts, making connections, testing etc. as required.(I) Short point (up to 3 mtr.) |
| 69 | (II) Medium point (up to 6 mtr.) |
| 70 | (III) Long point (up to 10 mtr..) |
| 71 | P & F 18 SWG Sheet steel boxes duly finished with two coats of red oxide and with earthing terminal of following sizes (nominal size) on surface or in recessed as required.75mm x 75mm x 50mm |
| 72 | 150mm x 75mm x 60mm |
| 73 | 200mm x 250mm x 75mm |
| 74 | 250mm x 300mm x 75mm |
| 75 | P&F 240/415 V isolator conforming to IS:13947-III/ IEC 60947-3 on existing board / sheet including making connections with lugs, testing etc. as required. Triple pole Isolator. 63 A rating |
| 76 | Providing and fixing one piece construction white vitreous china squatting plate with an integral longitudinal flushing pipe, white P.V.C. automatic flushing cistern, with fittings, standard size G.I. flush pipe for back and front flush with standard spreader pipes with fittings, G.I clamps and C.P. brass coupling complete including painting of fittings and cutting and making good the walls and floors etc. wherever required :Single squatting plate with 5 litre P.V.C. automatic flushing cistern. |
| 77 | P & F of IP20 LED batten type light fixture made from CRCA sheet stlle housing suitable for mounting LED tube system (integral driver), Power consumption of18W/36W, 1500/3000 lumens, system lumen efficiency 80 lm/ watt output, life time of 50000 burning hours with 70% initial lumen maintained. CCT 3000° K, 4000° Kand 6000° K. 4’ LED Tube shape fixture 18W/20w |
| 78 | Plate Earthing as per IS:3043 with G.I. Earth plate of size 600mmx600mm x 6.0mm by embodying 3 to 4 mtr. below the ground levelwith 20 mm dia. G.I. 'B' class watering Pipe including all accessories like nut, bolts, reducer ,nipple, wire meshed funnel, and C.C. finished chamber covered with hinged type with locking arrangement C.I. Cover, C.I. Frame of size300mm x 300mm complete with alternate layers of salt and coke/ charcoal, testing of earth resistance as required. |
| 79 | P&F 240/415 V MCB of breaking capacity not less than 10 KA (B/ C/ D tripping charact- eristic) ISI marked IS 8828(1996)]/ confor- ming to IEC 60898 in existing board/sheets including making connections with lugs, testing etc. as required. Double pole MCB.(l) 6 A to 32 A rating |
| 80 | (ll) 40 A to 63 A rating |
| 81 | P&F Recessed/ Surface mounting heavy duty horizontaltype sheet steel Distribution board phophatised/ powder painted complete with copper bus bar, shorting link , neutral link, earth link and din bar, conforming to IS13032 & IS8623 including making internal DB terminations with copper lugs , testing etc. as required. Single door (Three phase) 12Way |
| 82 | P & F of IP20 LED Recessed/ Surface Mounted Round/ sqaure Non Dimmable Downlight with die-cast aluminum housing & Heat sink for heat dissipation, high purity reflector with external driver having efficiency > 85% and in ompliance to IEC standards. ( supplied together with luminaire) Power consumptionof =<7w/10w/8w/12w/15w/18W with100/500/750/1100/1250 lumens, system lumen, efficeancy of 70 lm / Watt or 100 lm / Watt output suitable to replace 1x18W/ 2x18w/2x26w CFL downlights, life time of 50000 Burning Hours with 70% of intial Lumen maintained. CCT 3000° K, 4000° K and 6000° K. Fixture shall be CE Compliance. LED downlight 12/15/20 W(I) LED downlight 2/3 W |
| 83 | (Il) LED downlight 14/15 W |
| 84 | (Il) LED downlight 18/20 W |
| 85 | Surface Mounting(lV) LED downlight 6/7 W |
| 86 | (lV) LED downlight 18/20 W |
| 87 | Providing & Fixing of IP40 LED Surface/ Recessed / suspended mounting Mid power SMD type LED Light fixture made from CRCA sheet steel housing, high purity / transmisivity UV stabilized Non -yellowish diffuser for uniform light distribution. High efficiency with 2.5 KV internal/external surge protection BIS certified isolated driver having efficiency > 85% , with Short & Open circuit protection and in compliance to IEC standards (Integral with light fixture). System lumen efficacy of ≥ 120 lm/Watt ,THD < 10 % , p.f.≥0.95,CRI >80 , life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of BISstandard and trade mark certificate ( T.C.). Manufactures WordMark/ Name Engraved/ Embossing/ Screen printing on housing.OEM must have its own in house NABL lab setup for all testingfacilities for LED fixtures. (LM79/LM80) certificate / Report fromOEM shall be submitted. All as per pre approved by engineer incharge . foe additional technical parameters of product/ work, referAnnexure \\"A\\" attacheded with this BSR.36W LED light fixture 2'x2' with acrylic / prismatic front cover. |
| 88 | 48W LED light fixture 2'x2' with acrylic / prismatic front cover. |
| 89 | Providing & Fixing of IP 20 box made out from 1.2mm thick CRCAsheet steel with depth of minimun 30 mm and finished with powdercoating and suitable for mounting LED tube including side covers,holders , internal wiring to illuminate the single sided connectionLED tube. ( Without tube). All as per pre approved by Engineer incharge. For additional technical parameters of products/ work ,refer Annexure \\"A\\" attached with this BSRSuitable for 4' LED Tube shape fixture 1 X 18/20 W |
| 90 | Suitable for 4' LED Tube shape fixture 2 X 18/20 W |
| 91 | P/Laying P.V.C/XLPE insulated & P.V.C sheathed cable of 1.1 KV grade with Copper conductor of IS: 1554 P-I/IS: 7098 P-I of Group 1 of approved make in ground as per IS: 1255 including excavation of 30cm x 75cm size trench, 25cm thick under layer of sand, second class bricks covering, refilling earth, compaction of earth, making necessary connection, testing etc. as required of size.(I) 36/40W LED Light 1’x4’ with acrylic/ prismatic front cover(I) 2.5sq mm. Armored 4 core |
| 92 | (Il)1.5 Sq.mm Armoured 6 Core |
| 93 | (Ill)1.5 Sq.mm Armoured 12 Core |
| 94 | Providing and fixing of fuse box size 250(H) x 200(W) x 150(D) mm with base shape accomodating the pole partly, fabricated of 1.6mm MS sheet with hinged cover, dust and vermin proof, rubber gasket, locking arrangement, duly holded with 2 nos pole clamps of 25mm x 3mm flat with nut and bolts, complete with anticorrosive treatment,finished with two coat of approved enamel paint. The box shall be provided with 2/ 4 nos copper bus bar 150 x 20 x 3mm with brassscrews suitable supports,earth terminal, inter connection, brass cable gland upto 10 Sqmm size cable, 2nos 16 Amp kitkat fusecomplete in all respect. |
| 95 | P&F of capacitor start single phase metallic blade fresh air fan, in existing opening including cost of hardware , flexible copper conductor ,making connections, testingetc. as required. 225 mm sweep |
| 96 | P&F 240/415 V isolator conforming to IS:13947-III/ IEC 60947-3 on existing board / sheet including making connections with lugs , testing etc. as required.Four pole Isolator 63 A rating |
| 97 | P & F office one module call bell system comprising of indicator, push to reset switch housed in pvc/metallic sheet including making connection testing etc. as required |
| 98 | P & F ISI marked single tone electronic call bell including making connection testing etc. as required. |
| 99 | P & F of 3.00mm PVC sheet for fan box with help of screws, cup washer as required |
| 100 | Providing and fixing Mild steel railing including painted, complete as per drawing and technical specification and as per clause 1900 & 2703.2 of MoRT&H Specification including all material, labour, machinary etc. |
| 101 | Stone work ( machine cut edges) for wall lining upto 10 m height etc. (Veneer work) backing filled with a grout of 12mm thick cement mortar 1:3 (1 Cement : 3 coarse sand) and jointed with Cement mortar 1:2 (1 cement : 2 stone dust) including rubbing and polishing complete. (To be secured to the backing by means of cramps whichshall be paid for separately)Kota stone slabs exposed face dressed and rubbed.25 mm thick. |
| 102 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level :1:4:8 (1 Cement : 4 fine/ coarse sand : 8 graded stone aggregate 40mm nominal size). |
| 103 | Providing and fixing of precast concrete interlocking tiles of desired shape of M 30 grade manufactured from fully computerized automatic stationery hydraulic viebro pressed machine and fully computerized automatic batching plant of class A1/A2 as per BS 6717:2001. The CC interlocking paving blocks be laid on average 50mm. thick bed of coarse sand and the joint is to be filled with fine sand. Laying procedure on compacted sub-base as defined. Complete job is to be executed as per the instruction of Engineer incharge. The rates to be inclusive of all lead & Lifts etc. complete asper specifications. Tensile splitting strength, abrasion and brakingload etc. as per BS 6717:2001, Grey cement.60mm thick |
| 104 | 80mm thick |
| 105 | Flooring with Cobble stone of approx. Size 125x125x75 mm (thick) laid on 25 mm average thick cement mortar 1:3 ( 1 cement : 3 Coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the stone, laid in approved pattern complete in all respect as per direction of Engineer-in-charge. |
| 106 | Supplying and stacking good earth at site of work.Note: 1) Loading, unloading and carriage to be paid extra as peractual lead.2) Earth measured in stacks will be reduced by 20% foe payment |
| 107 | Carriage of Materials by mechanical transport including loading, unloading and stacking :: upto 3 km Earth |
| 108 | Earth work in excavation for roadway, including trimming bottom and side slopes in accordance with requirement of line, grades and cross sections, including disposal of surplus material with all lift and lead upto 1000 metre as per MoRT&H specification clause 301In all type of soil |
| 109 | Chequered terrazo tiles 22 mm thick with graded marble chips of size up to 6 mm in floors jointed with neat cement slurry mixed with pigment to match the shade of the tiles including rubbing and polishing complete on 20 mm thick bed of cement mortar 1:4 (1cement :4 coarse sand) :Light shade using white cement. |
| 110 | Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and cleaning etc. complete on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand).Medium shade using 50% white cement 50% Grey cement. |
| 111 | Random rubble dry stone Kharanja (soling) under floor. |
| 112 | Construction of Tube-well upto 100 Meter depth and above in alltype of rocks by DTH system and over burden to accommodatecasing pipe of following sizes in all types of soils and over burden including lowering of casing pipes but excluding cost of casing pipesas per IS : 2800 (Part I & II) 1979 specifications. The work would be completed after obtaining sand free water. The tube well should have a throughout bore as per nominal dia of casing pipe:200 mm dia Nominal bore |
| 113 | Supply of strainer pipes made of ERW M.S. black pipe ISI mark of following sizes at the site of work including required size of slotting as per IS:8110-1985 of following nominal bore sizes at site of work. 200 mm dia |
| 114 | Providing & Fixing of Single Stage, water cooled, High Speed(2880RPM), Horizontal, Centrifugal, Openwell Submersible pumps set prefilled with coolent water and fitted with mechanical seal - T/C Vs T/C,Thrust bearing shall be of carbon + S.S.The stator body of singlephase pump shall be of SS and rest of all shall be of cast iron. Allcasting parts should be cathod electro deposition (CED) coated andother construction material should be confirming to IS : 14220: 2018. The overall performance of pump shall confirm to BEE energyefficiency level of 3 star. Valid BEE certificate from OEM must besubmitted for the same. Motor should be IE2 class as per IEC60034-2-1: 2007, IEC 60034-30: 2008, & IS12615:2011, includingmaking connection etc as required complete in all respect. All as perpre approved by Engineer in charge. For additional technicalparameters of products/ work , refer Annexure \\"A\\" attached withthis BSR .3.0 HP, 1-Ø, (40 -170)Mtr, (60- 20) LPM |
| 115 | 150 mm diameter Submersible pump shall have following HPRating, phase, Head range, Discharge range respectively.3.0 HP, 3-Ø, (54 -95)Mtr, (250-50) LPM |
| 116 | Supply and fixing of tube well cover of M.S. sheet (6mm thick) withnuts and bolts complete for casing size:200 mm dia |
| 117 | Providing, lowering, laying & jointing MDPE/ HDPE pipes (Class-PE 80) PN 12.5 composite pipes for extra length for house service connections as per drawing and specifications complete including all material, labour, testing and commissioning as per Technical Specifications and as per direction of Engineer. With HDPE pipe32 mm dia service pipe |
| 118 | Supply and fixing of M.S. clamp set of 50 ×6mm flat iron with nutsand bolts etc. for holding the riser pipe assembly of submersiblepump set. |
| 119 | Providing & fixing UV stabilised fibreglass reinforced plastic sheetroofing upto any pitch including fixing with polymer coated 'J' or 'L'hooks, bolts & nuts 8mm dia. G.I plain/bitumen washers completebut excluding the cost of purlins, rafters, trusses etc. The sheetsshall be manufactured out of 2400 TEX panel rovigs incorporatingminimum 0.3% Ultra-violet stabiliser in resin system underapproximately 2400 psi and hot cured. They shall be of uniformpigmentation and thickness without air pockets and shall conform toIS 10192 and IS 12866.The sheets shall be opaque or translucent,clear or pigmented, textured or smooth as specified2mm thick flat. |
| 120 | Supply , Installation, Testing and Comissioning of ducting made fromaluminium sheet metal fabricated as per IS:655 with minimumgalvanising coating not less then 100 GSM and as per approveddrawings & designs including the cost of hangers, supports , angle ,expansion fasteners , closed cell neoprene gasket T&P etc. asrequired of following gauge:- All as per pre approved by Engineer incharge. For additional technical parameters of products/ work ,refer Annexure \\"A\\" attached with this BSR .0.80mm (22 G) |
| 121 | Providing corrugated G.S. sheet roofing including vertical/ curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete upto any pitch in horizontal/ vertical or curved surfaces) excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.80mm thick with zinc coating not less than 275gm/m² |
| 122 | Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. |
| 123 | Supplying and Laying ISI marked P.V.C. insulated submersiblecable as per PWD specification for electrical Works confirming toIS:694 and as per IS 8130 : 2013 of 1.1 kV grade .Wire should be made from 99.99% purity copper, class 5 stranding in acc. to IEC 60228 for lower watt loss , oxygen free ( <10 ppm) for less chances of oxidization and higher silver content for gives better conductivity, insulation PVC type A or C ,flame retardant as per IS 10810-53,better amperage rating as per VDE 0298 part 4 including making connection etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. All as per pre approved by Engineer in charge, making connections. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR4.0 Sq.mm 3 core flat / Round Please Enable Macros to View BoQ information |
