|
| 1 | Dismantling posts or struts (wood or R.C.C.) any section, including taking out embedded in concrete including dismantling of barbed wire fixed etc. |
| 2 | Dismantling wrought iron or mild steel work for barbed wire and old chain link fencing obtained from with old RCC or wooden pole ,rolling shutters,angles of any description. |
| 3 | Demolition of Brickwork or stone masonry, built in cement mortar including all quoins, arches, pillars, etc, complete all as specified and directed |
| 4 | Demolition of concrete (Unreinforced) in ground floors and pavings n. exc 15 cm thickness (below or above ground level) |
| 5 | Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance n.exc.50m and making good surface in hard/dense soil. |
| 6 | M&L for Cement concrete 1:3:6 type C2 (using 40 mm graded stone aggregate) in foundations, filling and mass-concrete all as directed by Engr-in-charge |
| 7 | M&L PCC (1:4:8) type D2 using 40 mm graded stone agg as in foundation filling & mass concrete. |
| 8 | M&L for Laterite stone Walling of squared rubble,regular coursed,well bonded and dressed ,bedded and solidly hearted,built in CM 1:6 complete all as aspecified and directed. |
| 9 | M&L for rendering 15mm thick in CM 1:4 on brick masonary surfaces and finished the even and fair without using extra cement |
| 10 | M & L For PCC type B-1, 1:2:4 (20mm graded stone aggerates) as in coping and the like. |
| 11 | S & F rolled mild steel in Joist, channel, angle,flat iron or tee sections Fe 410-W (Gde-E- 250 quality 'A') , fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) for chain link angles |
| 12 | S&F mild steel nuts and bolts not exc.12 mm dia of bolt and not exc. 75mm in length with two washers,one bolt all as specified. |
| 13 | M & L for preparation of new steel surfaces and applying two coats of synthetic enamel paint over a coat of red oxide on surfacess of any discription, over 10cm in width or girth. |
| 14 | S&F Galvanised 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured).for with new chain link fencing |
| 15 | S&F 4mm dia galvanised steel wire,(Chain Link PVC Coated) n.exc 100x100mm mesh, made up into mattresses or cages, lapped, wired and laid in position, including closing after filling complete all as specified and directed. Note: The dia of galvanised steel wire shall be of 4mm. |
| 16 | Cutting of bushes/Site clearence up to 1m both sides from the fencing |
| 17 | Removing of surplus spoil/dismantelled material exc. 250 M and n.exc 500 M, depositing where directed at a level n. exc. 1.50 M above the starting level.(hard/dense soil) |
| 18 | M &L for Framed work as in doors or gates of angle or other section with gusset plates, rails,braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening andfixing complete Fe 410 -W (GdeE- 250) quality A |
| 19 | Dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing) |
| 20 | M&L for cement concrete type C2 1:3:6 using 40mm graded stone aggregate 75 mm thick as in base of tiles etc. |
| 21 | M&L for Endura Industrial tiles 10mm thick (square/rectangular) area of each tiles exceeding 0.09 sqm but not exceeding 0.18 sqm in floors etc.set and jointed in neat cement slurry and pointed in white or coloured to match incl 20mm thick screed bed in CM 1:6 |
| 22 | M&L for Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath,parks, lawns, drive ways or light traffic parking etc., of required strength, thickness& size/ shape, made by table vibratory method using PU mould, laid in requiredcolour & pattern over and including 50mm thick compacted bed of coarse sand,compacting and proper embedding/ laying of inter locking paver blocks into the sandbedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed. Make Topaz tiles/ NITCO/ Mehtab tiles(Indore) |
| 23 | M&L for chequered cement concrete tiles (Rubber finished)20cmx20cmx25mm thick set,jointed and pointed in neat cement slurry in floors with grey cement and pigments including 20 mm thick screed bed in CM 1:6. |
| 24 | M&L for Granite (of any type) work 20mm thick (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including 20mm thick screed bed in CM 1:4 |
| 25 | M&L for Plain cement concrete 1:3:6 type C-2 using 40 mm graded stone aggregate as in drains, surface channels and the like including weathering, slightly rounded or chamferred angles and throating as directed and provision of necessary form work complete all as specified and directed. |
| 26 | Extra over serial item No.25 above for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement including forms, moulds, mitred/slopped ends etc complete all as specified and directed. |
| 27 | M&L for Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete.to be fixed in road side kerbs of size 30x45 cms of minimum thickness 10 cms complete all as specified and directed |
| 28 | Supplying and laying of 75mm CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches complete all as specified. |
| 29 | M&L for Hardcore of broken stone or boulder of gauge exc 63 mm but n. exc 100 mm, deposited, spread and levelled in layers n. exc 15 cm thick, watered and rolled/ rammed to a true surface complete all as specified and directed |
| 30 | M&L 75mm thick 1:3:6 type C-2,(40mm gradded aggregate) PCC in plinth protection finishing cement concrete even and smooth without using extra cement complete all as specified and directed |
| 31 | M&L Cement concrete type B-1,1:2:4 (20mm graded aggregate) 75 mm thick as flooring finished even and smooth complete all specified and directed |
| 32 | S&F for steel rolling shutters, (thickness of laths 1.25mm)with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pull or manual type |
| 33 | S&F for steel rolling shutters, (thickness of laths 1.25mm)with out ball bearing, but gear operated type with bevel gear box and crank handle as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pull or manual type |
| 34 | S&F for Safety lever locks mild steel with 4 levers for rolling shutters → |
| 35 | S&f for Ball bearing for rolling shutters as reqd all as specified and directed |
| 36 | S & F repair and fixed on existing pillers with concrete rolled mild steel in Joist, channel, angle,flat iron or tee sections Fe 410-W (Gde-E- 250 quality 'A') , fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) |
| 37 | S&F in repair Galvanised 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured). |
| 38 | M &L for Framed work as in doors or gates of angle or other section with gusset plates, rails,braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete Fe 410 -W (GdeE- 250) quality A |
| 39 | M&L for rendering 15mm thick plastering in cm 1:4 on brick masonary surfaces and finished the even and fair without using extra cement including Taking down cement plaster on brick or stone walls or ceiling surfaces etc including raking out joints hacking for key scrubbing down with water and include for all necessary lowering, etc., removal of rubbish off the premises, removal and depositing serviceable materials where directed and leaving the work clear of any plasteringcomplete all as specified and directed. |
| 40 | Supply only integral water proofing compound complete all as specified and directed. |
| 41 | M&L for preparation of new plastered surfaces of walls and applying two or more coats with 100% premium acrylic emulsion paint having VOC content less than 50 gms/litre and UV resistance as per IS 15489:2004, alkalie and fungal resistance, dirt resistance, exterior paint of required shade with silicon additives @ 1.43L/10sqm over and including priming coat of exterior primer applied at 0.9L/10sqm complete all as specified and directed by Engr-in-Charge |
| 42 | M&L for and applying of two coats of cement base paint over a coat of primer to the new plastered surface of walls complete all as specified and as directed by Engineer-in-Charge. |
| 43 | M&L for preparing old surfaces(plastered or unplastered) and applying two or more coats on old surfaces with 100% premium acrylic emulsion paint having VOC content less than 50 gms/litre and UV resistance as per IS 15489:2004, alkalie and fungal resistance, dirt resistance, exterior paint of required shade with silicon additives @ 1.43L/10sqm over and including priming coat of exterior primer applied at 0.9L/10sqm complete all as specified and directed by Engr-in-Charge. |
| 44 | Dismantling Asbestos cement (corrugated, semi-corrugated, etc.) sheets in roof coverings. |
| 45 | Dismantling of timber scantling in fillets, rails, posts, rafters,purlins, etc. under 40 sq. cm in section unframed work |
| 46 | S&F pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified. |
| 47 | S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified |
| 48 | S&F for Rolled sections as in main andcross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates Fe 410 -W (GdeE- 250)qualityA Please Enable Macros to View BoQ information |
