|
| 1 | Taking down steel/wooden/PVC/Aluminium door chowkat or frames exc 1.5 Sqm but n exc 4 Sqm each. but with shutters (without taking off shutters from the frames) |
| 2 | Taking down steel/wooden/PVC/Aluminium door with chowkat or frames n.exc 1.5 Sqm each. but with shutters (without taking off shutters from the frames) |
| 3 | Taking down shutter of any discription exc 1 sqm and n exc 2 sqm each and removing to store. |
| 4 | Refixing Aluminium / wooden / PVC doors( incl taking down, easing and adjusting and also refixing builder hardware as required) of shutter in same opening of any discription exc 1 sqm and n exc 2 sqm each |
| 5 | Refixing Aluminium / wooden / PVC doors( incl taking down, easing and adjusting and also refixing builder hardware as required)of shutter in same opening of any discription exc 2 sqm each |
| 6 | S & F pressed steel frames door 125 x 60 x1.25 mm with one or more rebates including necessary fixing lugs/hold fast duly tarred with bitumen and sanding with sharp clean sand, hinges, lock strike plate including filling of concrete 1:3:6 type C-1 back of chowkhats, with two coats of synthetic enamel paint over one coat of red oxide primer, including incl fixing of holdfast complete.NOTE:- During Fixing of chowkhat, surface shall be make good in plumb with existing finishes like cement plaster ,similar wall tile,floor tile etc and as per site requirement. |
| 7 | S & F pressed steel frames door 105 x 60 x1.25 mm with one or more rebates including necessary fixing lugs/hold fast duly tarred with bitumen and sanding with sharp clean sand, hinges, lock strike plate including filling of concrete 1:3:6 type C-1 back of chowkhats, with two coats of synthetic enamel paint over one coat of red oxide primer, including incl fixing of holdfast complete.NOTE:- During Fixing of chowkhat, surface shall be make good in plumb with existing finishes like cement plaster ,similar wall tile,floor tile etc and as per site requirement. |
| 8 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ®Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. complete all as specified and directed by engr in Charge. |
| 9 | S&F factory made fully guaged/ wire guage single extruded WPC (Wood PolymerComposite) brown colour solid 30 to 35mm sizecomprising of virgin polymer of K value 58-60.(Suspension Grade), calcium carbonate and naturalfibers (wood powder/ rice husk/wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100gms) having minimum density of 650 kg/cum and screwwithdrawal strength of 1800 N (Face) & 900 N (Edge),minimum compressive strength 50 N/mm², modulus ofelasticity 850 N/mm² and resistance to spread of flameof Class A category with property of being termite/borerproof, water/moisture proof and fire retardant and fixingwith stainless steel butt hinges of required size withnecessary full body threaded star headed counter sunk S.S screws No Black screw and at the top end two hinges to be provided, all as per direction of Engineer including Stainless steelwire cloth, 0.25 mm: to 0.36mm nominal dia of wire average width of aperture 1.40mm to 2mm and Aluminum XPM in rhombus shape, in one Piece from top rail to bottom rail all as specified and directed by Eng-in-Charge.NOTE :- All screws shall be self tapping chrome plated. |
| 10 | S&F Factory made single extruded WPC (Wood PolymerComposite) UV coated solid plain flush door shutter of 30 to 35mm thick size comprising of virgin polymer of K value 58-60.(Suspension Grade), calcium carbonate and naturalfibers (wood powder/ rice husk/wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100gms) having minimum density of 650 kg/cum and screwwithdrawal strength of 1800 N (Face) & 900 N (Edge),minimum compressive strength 50 N/mm², modulus ofelasticity 850 N/mm² and resistance to spread of flameof Class A category with property of being termite/borerproof, water/moisture proof and fire retardant and fixingwith stainless steel butt hinges of required size withnecessary full body threaded star headed counter sunkS.S screws, in kitchen cupboards and room wardrobes shutter all as per direction of Engineer |
| 11 | Supply and fixing in repair for factory made Steel window/ Ventilator 1.25mm thick box type (primer coated) ERW hollow P section of size 60mmx25mm including grill using 10 sqmm bar double rebated both gauge and glass shutter comprised gauged glazed Skelton shutter ERW sec 50mmx20mm and 1mm thick with two open able leaf consisting two Nos sash bar of T Section 20mmx3mm complete welded to frame with one vertical mullion of ERW box type T Section of size 60mmx25mm and 1.25mm thick refer TD Drawing No CEAF/AR-480/2015 Sheet No 2(A)/4 dated 30.12.2015 including following fitting welded to frame shutter :(a) Hold fast,150mm long of 12mmx3mm made to shape O4 Nos per window (b) handle of Z Sec20mmx25mm, 100mm long-per No leaf (c) MS Tower bolt 150mm long-02No per leaf .(d) Z section 20mmx25mm, 100mm long stopper 1 No per leaf. (e) cleat 55mm long of hollow square 15mmx20mmx63mm welded to hinge. 1 No per leaf (f) MS Pintal hinges of size 75mmx12mm. 2 Nos per leaf, (g) Including two coats of synthetic enamel paint complete.(h) Stainless steel wire cloth, 0.25mm to 0.36mm nominal dia of wire & average width of aperture 1.40mm to 2mm &fixed with aluminium wire staples.(j) Glass pane 5 mm thick fixed with MS pin and oil putty. NOTE: During Fixing of window, surface Shall be make good in plumb with existing finishes like cement plaster, similar wall tile,floor tile etc and as per site requirement.cutting holes and good dismantled portion in PCC(1:2:4) type B1. |
| 12 | Supply and fixing factory made uPVC white colour Casement window single panel with S.S. friction hinges (300 x 19 x 1.9 mm), made of (small series) frame 47 x 50 mm & sash 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glass paneglazing bead of appropriate dimension (Area of window upto 0.75 sqm.) comprising of uPVC multichambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass shall be paid separately)Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Please Enable Macros to View BoQ information |
| 13 | Supply and fixing factory made uPVC white colour Casement window single panel with S.S. friction hinges (300 x 19 x 1.9 mm), made of (small series) frame 47 x 50 mm & sash 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glass paneglazing bead of appropriate dimension (Area of window upto 0.75 sqm.) comprising of uPVC multichambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass shall be paid separately)Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Please Enable Macros to View BoQ information |
