|
| 1 | Labour for cleaning the work site before and after work etc. |
| 2 | Earthwork in excavation in foundation trenches in ordinary soil (vide classfication of soil item - A) and disposal of excavated earth a obtained to a distance up to 50M including all lifts with leveling ramming the foundation trenches removing roots of trees shurbs all complete as per approved design and per building specification and direction of E/I. |
| 3 | Extra for earth work in hard soil as per specification and direction of E/I (vide classification of soil Item B) |
| 4 | Filling in foundaion trenches and plinth in layers not exceding 150 mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I. (mode of measurement compacted volume). |
| 5 | Providing coarse clean sand in filling in foundation trenches or plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts includng cost of all materials, Labour, rotalty and taxes all complete as per building specification and direction of E/I (Mode of measurement compacted volume). |
| 6 | Providing designation 75A one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I. |
| 7 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:3:6 (1 Cement: 3 coarse sand (zone-III): 6 graded stone aggregate 20mm nominal size) |
| 8 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (1 cement: 2 coarse sand (zone-III): 4 graded stone aggregate 20 mm nominal size) |
| 9 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level.1:1.5:3 (1 cement: 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size) |
| 10 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement: |
| 11 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level.1:1.5:3 (1 cement: 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size) |
| 12 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1cement: 1.5 coarse sand(zone-III): 3 graded stone aggregate 20 mm nominal size). |
| 13 | Providing and fixing fan hook of 16 mm dia M.S. bar 1 metre long bent to required size and shape, placed in position and fixed in RCC slab/beam at the time of casting all complete as per building specification and direction of E/I. (where material is not supplied by deppt.) |
| 14 | Providing designation 75A brick work in C.M.(1:6) in foundation and plinth-do- |
| 15 | Providing designation 75A Brick work in C.M.(1:6) in superstructure -do- |
| 16 | Providing designation 125mm thick Inforced designation 75A brick work in cement mortar (1:4) In Superstructure with apprved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening carriage of materials, scaffolding, raking out joints to 15 mm depth, curing, taxes and royalty (but exludindig the cost of reinforcement) all complete as per building specilication and direction of E/I. |
| 17 | Providing 6 mm thick cement plaster (1:4) in celling with clean coarse sand of F.M 1.5 Including screening, curing with all teads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/L |
| 18 | Providing 12mm cement plaster (1:6) with clean coarse sand of FM 1.5 with floating coat of neat cement in skirting Including rounding of Junctions with floor, curing, taxes and royalty all complete as per building specifications and direction of Engineer In Charge |
| 19 | Providing 12mm. thick water proof cement plaster (1:3) with clean Es co/coarse sand of F.M 1.5 with 5% cico or any other approved water proofing compound including. -do- |
| 20 | Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete |
| 21 | Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface Including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper applying putty wherever required scaffolding wahing of floors and taxes all complete as per building specifica tionand direction of E/I. |
| 22 | Providing two coats of synthetic enamel paint of approved shade and make oversew wooden surface Including preparing the surface after cleaning, removing dirt, dust, scales, smoke, and grease and cleaning the surface throughly including cost of scaffolding and taxes all complete as per building specification and direction of E/I. |
| 23 | Provikling two coats of painting with ready mixed paint of approved shade and make over new wooden surface Including preparing the surface after cleaning, removing dust, dirt, scales, smoke and grease and cleaning the surface thoroughly including cost of scaffoldings and taxes all complete as per building specification and direction of E/I. |
| 24 | Providing primer one coat of approved shade and make over new wooden surface including preparing the surface after cleaning,removing dirt, scales, smoke, grease, and sand papering, including cost of scaffolding and taxes all complete as per building specification and direction of E/I. |
| 25 | Providing primer one coat of red lead paint of approved make over new steel surface including preparing the surface after cleaning, removing dust, dirt, scales smokes and grease and cleaning the surface thoroughly including cost of scaffolding and taxes all complete as per building specification and direction of E/I. (Mode of measurement Area shall be multiplied by the co-efficient as indicated in building specification). |
| 26 | Providing two coat of snowcem of approved shade and make over a coat of cement primer on new surface Including preparing the plastered surface smooth with sand paper, scaffolding, curing and taxes all complete as per building specification and direction of Engineer in Charge. |
| 27 | Providing and laying vitrified floor tiles in different sizes (thickness to bespecified by the manufacturer) with water absorption less than 0.08%and conforming to IS : 15622, of approved make, in all colours andshades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarsesand), including grouting the joints with white cement and matching pigments etc., complete.Double charge vitrified tile polished finish of sizeSize of Tile 600 x 600 mm |
| 28 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based)conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately)Size of tiles 600x600mm |
| 29 | Providing and laying 25mm thick kotah stone slab flooring of approved size texure and colour over 19mm thick base of lime mortar (1:1:1) (limeputty:surkhi:coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I. (i) 300x300 mm size. |
| 30 | Providing and laying 25mm thick kotah stone tiles in zisers of steps, skirting and pillars of approved size, texture and colour lald over 12mm thick cement morter (1:3) and Jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification direction of E/I. |
| 31 | Providing 25mm thick first class patent stone flooring (1:2:4) with stone chip in two layers, bottom layer 19mm. thick (1:2:4) with 12mm to 6mm size graded stone chips and top layer 6mm. thick (1:2) with 6mm down stone chips, in panels-including cost of curing, finishing the surface smooth by rubbing with carborandum stone, taxes and royalty with al complete as per building specification and direction of E/I. |
| 32 | Extra for providing and fixing 30 x 4 mm glass strips in joints of flooring complete Job all complete as per building specification and direction of E/I. |
| 33 | Providing, hoisting and fixing above plinth level up to floor five level precast Reinforced cement concrete in lintels, beams and bressumers, including setting in cement mortar 1:3 (1 cement: 3 coarse sand), cost of required centering and shuttering but, excluding the cost of OF reinforcement, with 1:1.5:3 (1 cement: 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size) |
| 34 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, windowsills, factas and strailar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement: 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. |
| 35 | Providing and laying 6mm precast white glazed tiles in walls over 12mm cement mortar (1:3) and Jointed with grey cement slurry Aush pointed with white cement Including rubbing, polishing and cost of curing, taxes and royalty all complete as per building specification and direciton of E/I. |
| 36 | Supplying fitting and fixing good quality well dressed and well seasoned sal wood work in chauket and door window sky light fan light C/W celeatal window opening, Including wedge over all clamp complete Including application of two coat of wood preservative of approved quality on he surface butting wall and lintel all complete as per bullding specifications and directions of E/! |
| 37 | Supplying fitting and fixing 35mm thick solid core type non-decorative single leaf flush shutter in doors and windows with black board core blended with high quality phenol Formal dehyde synthetic resin both side commercial veneered of standard make with oxidized Iron fittings such as hinges, sliding doors, bolts, tower bolts, handles or rings, hooks and eyes, cleats, sand, blocks as per schedule. Taxes and royalty all complete, as per bullding specification and direction of E/I |
| 38 | Supplying fitting and fixing 35mm thick solid core type non-decorative double leaf flush shutter in doors and windows with black کھا board core blended with high quality phenol formal dehyde synthetic resin both side commercial veneered of standard make with oxidized iron fittings such as hinges, sliding doors, bolts, tower bolts, handles or rings, hooks and eyes, cleats, sand, blocks as per schedule. Taxes and royalty all complete, as per building specificallon and direction of E/I |
| 39 | Providing and fixing factory made door frame (single rebate) made out of single plece extruded solid PVC foam profile with homogenous fine cellular structure having smooth outer integral skin having 62mm width and 32 mm thickness, frame will miitred and joined with self driven self tapping screw of size 38mmx40mm and PVC solvent cement, Including fixing the frame to wall with sultable dia and length anchor fastener as per manufacture specification and direction of E/I. |
| 40 | Providing and fixing factory made PVC door shutter made of solid foam PVC profiles of thikness 5 mm and 15 mm at edges integrally extruded for vertical style and horizontal (top/ bottom/ lock) rails of minimum cross section of 70mmx 28mm, of shape and design as per manufacturer's specifications having homogenous fine cellular structure and smooth integral outer skin, inserted with G.I. 'C' section/ rectangular tube profile of minimum 0.30 mm thickness with 120 gsm coating as stiffeners as per manufacturer's specifications Mitred cut joints for styles and rails provided with telescopic polymeric 'L' corners are jointed together using solvent adhesive and strenghtened with fully threaded stainless steel screws (of required size) through reinforced stiffener with paneling of specified solid foam PVC board/ high pressure laminate of required thickness and of approved design and shade (matching the styles and rails), secured within styles and rails with specially designed solid foam PVC moulded beadings of required size using PVC solvent adhesive/ cement. The finished door shutter including SS hardware, 1 no. ss sliding bolt 200 x 10mm, 1 no. SS tower bolt 200 x 10 mm and 2 nos. SS handles 125mm, shall be fixed to frame with 3 nos. stainless steel hinges of minimum size 100x58x1.9 mm and stainless steel screws of required size complete as per direction of the Engineer-in-Charge. (Cost of above hardware is inclusive in rates)5 mm thick solid foam PVC panel of required size with moulded/extruded beading of appropriate design shape and size as per manufacturer's specifications (to secure the panel insert tight in place within the style and rails of shutter) matching the colour and shade of shutter frame. Decorative type. |
| 41 | Spuplying fitting and fixing collapsible gate of approved size and make properly fabricated with vertical double channel 20 x 20 x 2 mm at 100mm. Centered and braced with M.S flat dlagnolas 20 x 3mm with top bottom rails of T iron 40 x 406mm with 38 mm dla steel pulleys complete with bolts, nuts, locking arrangement, stoppers, handles, Including applying a priming coat of red lead paint, carriage hosting and taxes all complete as per building specification and direction of E/I. |
| 42 | Supplying fitting and fixing fully glazed steel doors, windows or ventilators of standard rolled 'z' and mullion steel sections and sizes as per IS-1038 joints met and welded with 100x16x3mm M.5 lugs fixed in cement concrete (1:2:4) blocks 15x10x10cm,size including cost of oxidized iron fittings, with hinges, handles, handle per sters, catch springs, 3mm thick plain glass panes with alumlokum beads and inner frame fixed with lugs with 20mm long 6.3mm G.I counter sunk machine screw and nuts and applying a coat of red lead paint carrlage to work site hosting and placing in position in all storyes and taxes all complete as per building specifications and direction of Engineer-In-charge. |
| 43 | providing and fixing stainless steel(grade304) railing made of hollow tube, channel, plates etc, Inclaluding welding, griding, buffing, polishing and making curvature(wherever required)and fiting the same with necessary stainlesssteel nuts and bolts complete,i/c fixing the ralllag with necessary accessories&stainless steel dash fasteners, stainless steel bolt etc of required she, on the top of the floor or the side of walst slab with suitable arrangment as per approvel of E/! 2KG/FT |
| 44 | Supplying, fitting and fixing M.S. grill made of 20x6cmm M.S flat as per approved design and drawing, properly fabricated with Joints continuous fillet welded and finished smooth, carrlage of grill to work site, hoisting as per building specification and direction of E.I (where material is not supplied by the deptt.) |
| 45 | Supplying, fitting and fixing M.S. grill Gate with M.S grill made of 20x6 mm M.S flats or 16 mm M.S square bars fitted on 25x25x6 mm. M.S Angle frame-do- (when steel is not supplied by the deptt.) |
| 46 | Providing precast cement concrete Jali 1:2:4 (1 cement: 2 coarse sand(zone-III): 4 graded stone25 mm thick |
| 47 | Providing Tor steel reinforcement of 8mm dia rods as per approved -do- TMT Fe 500 (Only valid for Tata (Tiscon), SAIL, JSPL, Electrosteel Steels Ltd. Bokaro and Vizag (RINL) |
| 48 | (a) 10 mm (TMT coil Fe 500) {Only valid for Tata (Tiscon), SAIL, JSPL Electrosteel Steels Ltd. Bokaro and Vizag (RINL)} |
| 49 | (b) 12mm (TMT coil Fe 500) (Only valid for Tata (Tiscon), SAIL. JSP/Electrosteel Steels Ltd. Bokaro and Vizag (RINL)} |
| 50 | (b) 16mm (TMT coil Fe 500) (Only valid for Tata (Tiscon), SAIL. JSP/Electrosteel Steels Ltd. Bokaro and Vizag (RINL)} |
| 51 | Making plinth protection 50mm thick of cement concrete 1:3:6(one cement 3 corse sand:6 graded stone aggrete 20mm size)over 75 mm thick bed of dry brick blast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth as perE/I |
| 52 | Providing 150 mm wide brick drain in cement mortar (1:6) with av. 150 mm clear depth and 125 mm apron Including cost of earth work Involved with 75 A, flat soling in proper grade and slope at the base, the drain duly plastered In C.M (1:3) with punning over exposed surface all complete as per building specification and direction of E/I. |
| 53 | Water proofing for old and new roof slab….... Do........E/I. |
| 54 | centering and shuttering including strutting, propping etc. and removal of form for |
| 55 | Lintels,beams,plinth beams girders,bressumers and cantilevers |
| 56 | Suspended floors,roofs,landings,balconies and acess platform |
| 57 | Columns,pillars,piers,abutments,post and struts |
| 58 | stairs,(excluding landing)except spiral-staircases |
| 59 | Sand (Lead Upto 42 km) |
| 60 | Local Sand (Lead 18 KM) |
| 61 | Stone Chips (Lead 15KM) |
| 62 | Bricks 08 KM |
| 63 | Earth (Lead 01 KM) |
| 64 | Supplying fitting and fixing white glazedfire's clay skin of approved make with over flow arrangements supported on C.Ior R.S painted brackets 40mm dia PVC west pipe about 750mm long with brass coupling at one end and 15mm C.I body brass spindle bib cock of approved quality of weight not nless than 450 grams including cutting wall and making good the same etc. all complete as per specification and direction of E/I. Kitchen sink 600mm x 450mm x 250mm |
| 65 | Supplying, fitting and fixing viterous white glazed earthen ware I.W.C. of parry Hindustan or any other I.S.S. approved make with 100mm H.C.I. 'p' trap 15 litres C.I. pull and let go flushing cistern of names or other I.S.S. equivalent make, complete with all fittings, C.I. or C.C. brackets 32mm alkathene/P.V.C. telescopic flush, pipe about 2M long with one brass coupling and clamps G.I. chain and pull including supplying and fixing a pair of viterous white glazed earthenware footrest to be fixed in floor 15mm C.I. body brass spindle stop cock of weight not less than 50grms, 15mm P.V.C. connection pipe 450mm long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and dirction of E/I.580mm long - With 12.5 Liter Low Level P.V.C. costern580mm long - With 12.5 Liter Low Level P.V.C. costern |
| 66 | Supplying fitting and fixing viterous white glazed earthen ware wash hand basin of parry or Hindustan or any other I.S.S. approved make supported on painted C.I. or R.S. brackets 32mm C.I. brass waste, 15mm dia C.I. body brass spindl stop cock approved quality of weight not less than 30 grams, 32mm P.V.C. waste pipe 750mm long with brass coupling at one end and making plumber joints etc. all complete as per specification and direction of E/I. |
| 67 | Providing and fixing white vitreous china pedestal for wash basincompletely recessed at the back for the reception of pipes andfittings. |
| 68 | Supplying, fitting and fixing the following items complete with all materials as per specification and direction of E/I.C.P. brass towel rail 20mmx600 mm with brackets container etc. |
| 69 | Supplying, fitting and fixing the following items complete with all materials as per specification and direction of E/I.C.P. brass shoap dish container medium quality with screw and hinges etc. |
| 70 | Supplying, fitting and fixing the following items complete with all materials as per specification and direction of E/I.Mirrors of 6 mm thick plate glass bevelled edge mirror Including C.P brass revolving fittings 3mm ply wood board and C.P. hinges to fix with mirror.Mirrors of 6 mm thick plate glass bevelled edge mirror Including C.P brass revolving fittings 3mm ply wood board and C.P. hinges to fix with mirror.600mmx450xsize |
| 71 | 450x300mmsize |
| 72 | Providing and fixing N.P/C.P brass P.V.C porcelain shower rose of 15 mm inlet etc.all complete as per specification and direction of Enginer-in Charge.125mm dia P.V.C Shower |
| 73 | Supplying and fitting fixing H.C.I fittings of approved makes confirming to 1.5.5 1729 Including supplying nails and bobines lead and yarn from making lead caulked joints Including earth work or providing scaffoldig as the case may be complete as per specification and direction of E/LFloor Trap with Grantings100mm |
| 74 | Providing and fixing brass /C.I. stop cock approved quality all complete as per specification and direction of E/I. BRASS STOP COCKE- 15 mm dia |
| 75 | BRASS STOP COCKE- 20 mm dia |
| 76 | Providing and fixing 15 mm sizes C.P. brass pillar cock ( weight not less than 350 gms) C.I body brass spindle pillar cock of approved quality as per specification and direction of Enginer-in Charge. C.I body brass spindle |
| 77 | Providing and fixing male ended 15mm dia brass bib cock of approved quality (Wt. not less than 350 gms.) with extra socket all compere as per specification and direction of E/I. |
| 78 | Gi Pipe 50 mm dia (TATA or equivalent make) as per IS-1239(part-01)/2004 ISI Marked/Medium Quality |
| 79 | Supplying labours and tools for fixing G.1 pipes with red leads and yarn of following nomina: bore wih screwed and socketted jointed on wall, ceiling and floor including suppying and fitting of wall hooks or pipe clamps, wooden plugs, cutting pipes to size and threading ends if rquired etc. all complete as per specification and direction of E/L (Including piple and socket to be supplied departmentally free of cost)15mm dia |
| 80 | 20mm dia |
| 81 | 25mm dia |
| 82 | 32mm dia |
| 83 | 40mm dia |
| 84 | Supplying and fixing G.I fitting of approved make all complete as per directions of E/I.ELBOW15mm dia |
| 85 | 20mm dia |
| 86 | 25mm dia |
| 87 | 32mm dia |
| 88 | 40mm dia |
| 89 | TEE PLAIN15mm dia |
| 90 | 20mm dia |
| 91 | 25mm dia |
| 92 | 32mm dia |
| 93 | 40mm dia |
| 94 | REDUCING SOCKET20mm dia |
| 95 | 25mm dia |
| 96 | 32mm dia |
| 97 | 40mm dia |
| 98 | NIPPLE15mm dia |
| 99 | 20mm dia |
| 100 | 25mm dia |
| 101 | 32mm dia |
| 102 | 40mm dia |
| 103 | PLUG15mm dia |
| 104 | 20mm dia |
| 105 | 25mm dia |
| 106 | 32mm dia |
| 107 | 40mm dia |
| 108 | REDUCING TEE PLAIN20mm dia |
| 109 | 25mm dia |
| 110 | 32mm dia |
| 111 | 40mm dia |
| 112 | UNION SOCKET15mm dia |
| 113 | 20mm dia |
| 114 | 25mm dia |
| 115 | 32mm dia |
| 116 | 40mm dia |
| 117 | SOCKET 15mm dia |
| 118 | 20mm dia |
| 119 | 25mm dia |
| 120 | 32mm dia |
| 121 | 40mm dia |
| 122 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.110mm diameter (for rain water) |
| 123 | 110mm diameter (for waste water) |
| 124 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion Bend 87.5° 110 mm bend |
| 125 | 110 mm shoe |
| 126 | Single tee Without door 110x110x110mm |
| 127 | Single tee With door 110x110x110mm |
| 128 | Supplying fitting and fixing H.C.I pipes with ear of approved make confirming to 1.5: 1729 Including supplying nails bobins short pipes cutting loose collars, lead and yarn for making lead caulked Joints, cutting pipes to size including earth work or scaffolding where necessary etc.All complete as per specifications and direction of E/I100mm dia |
| 129 | 75mm dia |
| 130 | Supplying and fixing H.C.I fitting of approved make confirming to 1.S.S:1729 Inclutding supplying nails and bobins lead and yarn from making lead caulked joints including earth work or providing scaffolding as the case may be all complete as per specification and direction of E/LH.C.I Signal junction with door but without ear except socket80mm dia (wt. 75kg) |
| 131 | H.C.I double junction with door and ear100mm dia (wt. 15.5kg app) |
| 132 | H.C.I double inverted junction100mmx50mmx50mm |
| 133 | H.C.I bent with door and ear80mm dia (wt.4.5kg app) |
| 134 | H.C.I plain bent with ear100mm dia (wt.5.5kg app) |
| 135 | 80mm dia (wt.3.75kg app) |
| 136 | Norton patent H.C.I cowel100mm dia (wt.3.25kg app) |
| 137 | Supplying all tools and labours and cutting chajja, comice, for laying H.C.I pipes and making good the same as per specifications and direction of E/I |
| 138 | Cutting drain width wise above G.L for laying H.C.I plpe and restoring brick work in cement mortar (1:4) 12mm cement plaster In (1:4) with net cemant punning as per specification and direction of E/I |
| 139 | Making holes in walls for laying H.C.I pipes and restoring the same after pipe laying as per specification and direction of E/I250mm dia |
| 140 | R.C.C Chajja |
| 141 | Supplying material and labour for painting exposed H.C.I pipes and fitting with 2 coats of approved paints over coat of red oxide primer etc. all complete as per specification and direction of E/I80mm dia |
| 142 | 100mm dia |
| 143 | Providing and fixing gun metal full way valve of approved quality, all complete as per specification and direction of E/I25mm dia and Wt not less than 500gms |
| 144 | 32mm dia and Wt not less than 700gms |
| 145 | 40mm dia Wt. not less than 1.0 kg |
| 146 | Cutting drain width wise above G.L for laying G.1. pipe and restoring with brick work In cement mortar (1:4) 12 mm cement plaster In (1:4) with net cement punning as per specification and direction of E/I |
| 147 | Cutting chajja or cornice for laying G.I pipe and restoring the same with R.C.C(1:2:4) brick work in cement mortar (1:4) cement plaster (1:4) as per specification and direction of E/I |
| 148 | Making holes in walls for laying G.I pipes and restoring the same after pipe laying as per specification and direction of E/I125mm Thick Wall |
| 149 | 250mm Thick Wall |
| 150 | Supplying, fitting and fixing of GM ferrule of approved make In DI/CI main Including drilling and tapping CI/BI main etc. all complete as per specification and direction of 3mm, 6mm, 10mm dia ferrule weight not less 425gm |
| 151 | Supplying and Labour for laying, fitting and fixing NP2 R.C.C spun pipe with collars in line, level and gradė and providing approved Jointing materials and Joints properly fitted to make them leak, proof Including providing sight rail, bonning rod, night guard, red light and barrier ect. All complete as per specification and direction and direction of E/L.150 mm dia R.C.C Spun pipe up to 3.0 metre depth of invert below G.L. |
| 152 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI: 12701 marked, with cover and suitable locking arrangement and making necessary holes for Inlet, outlet and overflow plpes but without fittings and the base support for tank.1000Lt. Tank Circular Tank |
| 153 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up toplinth grade level:1:12:3 (1 Cement: 1½ coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size) |
| 154 | Providing 12mm thk cement plaster(1:4) with clean coarse sand of F.M.including screening,curring with all lead and lift of water scaffolding, Laxes and royality all complete as per building specification and direction of E/I. |
| 155 | Providing 1.5 mm. cement punning including curing carrage of water withall leads and lifts as per building specification and direction of E/I |
| 156 | Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality Circular shape 560 mm internal diameter. |
| 157 | Making soak pit 2.5 m diameter 3.0 m deep with 45x45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter and 1.20 m long complete as per standard design with common burnt clay F.P.S. (non modular) bricks of class designation 7.5. |
| 158 | Point Wiring in PVC Conduit, with Modular type Switch: Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, with modular type switch, modular plate, suitable size GI box and earthing the point etc as required. |
| 159 | Circuit / Sub-main wiring in PVC Conduit: Wiring for circuit / sub-main wiring along with earth wire with the following sizes of PVC insulated, copper conductor, single core cable in surface/recessed PVC conduit as required. 2x2.5 Sqmm + 1x2.5 sqmm earth wire |
| 160 | 2x4 Sqmm + 1x4sqmm earth wire (For 1.5 Ton AC) |
| 161 | 4x6 Sqmm + 2x6 sqmm earth wire |
| 162 | 4x10Sqmm + 2x10sqmm earth wire |
| 163 | S/F Piano type switch / socket :- Supplying and fixing of following sizes of PVC conduit alongwith the accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required. 5/6 amps, one way switch |
| 164 | 3 pin 5/6 amps, socket outlet |
| 165 | S/F lpower plug point with piano type accessories :- Supplying and fixing sutiable size G.I./PVC box on surface or in recessed with phenolic laminited sheet cover in front including providing and fixing 6 pin , 15/16 amps socket outlet and 15/16 amps piano type switch connection , painting etc, as requried. |
| 166 | S/F Ceiling Rose: Supplying and fixing 2 pin ceiling rose on the existing junction box/ wooen block including connection etc as required. Make :- Anchor / Kona / Kany |
| 167 | S/F Batten / Angle Holder: Supplying and fixing batten / angle holder including connection etc as required. |
| 168 | ITC Ceiling Fan :- Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (Up to 30 cm) with 1.5 sq. mm. FRPVC insulated,copper conductor,single core cable etc, as required. |
| 169 | Supplying Ceiling Fan 48\\" (1200mm) |
| 170 | ITC Exhaust Fan upto 450 mm sweep: installation of exhaust fan upto 450 mm sweep in the existing opening, including making the hole to cut the size of the above fan, making good the damage, including connection, testing, commissioning etc as required. |
| 171 | Supply 9\\" (230mm) metal exaust fan |
| 172 | S/F rewireable double pole / TP&N switch disconnector:-Providing and fixing following capacity doble pole / TP&N sheet metal switch disconnector fuse unit in existing metal board with rewireable type fuses, including drilling holes in metal board, making connections, etc as requried. 32 amps, double pole |
| 173 | S/F S.P. MCB DB :Supplying and fixing following way single pole nutral , sheet, MCB dstribution board , 240 volts ,on surface/recess, complete with tinned copper busbar,nutralbusbar, earth bar,din bar, detachable gland plate,interconnection, phosphate and powder painted including earthing etc.as required.(But without MCB/RCCB/Isolator) .6way,single door |
| 174 | S/F 'B'serise, s.p.MCB:-Suppling and fixing 6amps to 32 amps rating , 240 volts, 'B' series, miniature circuit breaker suitable for lighting and other loads of folling poles in the existing MCB DB complete with connections, testing and commissioning et. as requried. 6/32amps, single Pole,\\"B\\" series. |
| 175 | P/F G.I. lightning conductor final:-providing and fixing of lightning conductor final, made of 25 mm dia 300 mm long, copper tube, having single prong. at top, with 85 mm dia 3 mm thick copper base plate Including hole etc. complete as required |
| 176 | P/F copper liglitning conductor tape In vertical run:- providing and fixing copper tape 20 mm x3 mm thick on parapet or surface of wall for lightoing conductor complete as required. Ifor vertical run) |
| 177 | Reverting, sweating and soldering lightning conductor tape:- Reverting, sweating and soldering of copper/G.I tape (with another copper/G.l tape, base of final or any other metallic object) as required. |
| 178 | P/F Testing joint for G.I. lightning conductor:- Providing and fixing testing Joint, made of 20 mm x 3 mm thick copper strip, 125mm long, with 4 nos. of tinned brass bolts, nuts, check nuts, and spring washers etc. complete as required. |
| 179 | P/F G.I. earth tape for lightning mm x 6 mm from earth electrode directly conductor:- providing and fixing copper tape In ground as required. |
| 180 | Supplying all materials, labours and tools and equipment for drilling 200 X 165mm dia. X 125 Mtr. bore well in all kinds of soil and rock in urban area for installation of pumps set with Hydraulic DTH Rig Machine, all complete including drilling rig, Air Compressor and equipments, as well as fuel, lubricants and cost of transporation of rig machine and over vehicles up to the site etc. all complete job as per specification and direction of E/lc.From 0-50 Meter |
| 181 | From 51-125 Meter |
| 182 | Supplying all tools, tackles & lowering of 200mm dia. MS ERW casing pipe of 6mm wall thickness including welding charges, cost of pipe etc including all taxes, VAT, Excise duty, freight charges with inspection charges etc as applicable, etc. all complete job as per specification and direction of E/lc. |
| 183 | Supplying all materials: labours, tools & equipments for fiting & fixing 200mm dia MS cap over casing pipe etc. all completes job. |
| 184 | Cleaning flushing and developing of drilled hole for testing the discharge of water development of bore well by continuous flow of water by using heavy compressor up to satisfaction of E/l. to get uninterrupted flow of water free from sand and soil etc. |
| 185 | Supplying of 150mm dia 03.00 H.P. (ISI Mark) KSB/Kirlosker/CRI/V-guard Submersible Motor Pump sets comfirming to IS 8034 and motor confirming to IS 9283. Pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415V + 10%, 3PH, 50Hz, A.C. supply with cable guard, thrust carbon/fiber bearing to withstand entire hydraulic thrust, water proof winding shall be provided. The pump set shall be suitable for direct coupling. Pump shall have suitable outlet as per manufacturers design. Anti thrust stream lined non returned valve shall be provided with pump. 3 meter submersible copper in single/double run shall be provided with each pump.(up to 20 stages) Supply rate should be increased by Rs 200/-per stage for pump with more than 20 stages. |
| 186 | FR PVC insulated 3 core 4 sq. mm. copper wire |
| 187 | Supplying of 32mm Submersible Pipe of standard make Ashirwad/Raksha/Prince/Gupta or any equivalent make for above requirement. |
| 188 | Supplying of 02 Nos. clamp, Band, Adopter, Bore Cover etc. as required for above work. |
| 189 | Supplying & Providing Rope of required size & tape. |
| 190 | Supplying & Fixing of BCH Make or Equivalent Panel Board with all accessories & Iron Box with Angle Stand and its fixing as per direction of E/l. |
| 191 | Installation Charges for Lowering of Motor Pump. |
| 192 | Supplying and of 10.0sq.mm Alluminium cable ISI mark as per specification and direction of E/l. (for connection from main line to electric Meter. |
| 193 | Mattress |
| 194 | Bed Sheet |
| 195 | Blanket |
| 196 | Pillow with Cover |
| 197 | Mosquito Net |
| 198 | Dinning Table |
| 199 | Chair |
| 200 | Wooden Chouki |
| 201 | Metal Drawer/steel almirah |
| 202 | CCTV Camera (13 Camera with all assessories) |
| 203 | Good & Service Tax (GST) |
| 204 | Labour Cess Please Enable Macros to View BoQ information |
