|
| 1 | Supply / Fixing of Rectangular pole of height 6 mtr made out of MS pipe as per IS 4923. The pole shall be PU painted The pole shall have in built junction box weather proof flush door & locking arrangement for housing at bottom of the pole. Pole shall be made out of 200 mm x 100 mm Rectangular section of thickness 4 mm with base plate dimensions 325x225x16 mm thick. The base plate shall be machined & chamfered all four side by 6 mm ,25x25x3 mm ,angle jacket to be weld at two places all around with base plate , so pole to protect the base plate & pole weld joint. & also give the strength to the pole . The body of the decorative pole shall be painted properly to give it a smooth surface.The pole should have arragement for fixation of the mounting the fitting and the top of the pole should be openable for maintenance of fhe fitting . The decorative pole shall be duly pre-treated ( with phosphating ) & epoxy primer inside & outside of the part and painted in UV ray resistant PU coating in required colour. The coating should have a DFT of 80 micros Average. The pole shall be Powder coated. fhe fitting As per the Approval of E/ in charge. LED FIXTURE Supply/ Fixing of LED fixture in the aluminum special section box of size (Size 120 x 186 x 150 mm). Two no SQ LED module 4 LED's for outdoor applications Specific lighting system designed for street/pathway lighting, having Wattage of 35 W LED. Corrosion resistant extruded aluminum aesthetic housing Closed by a toughened optical grade safety glass diffuser and sealed with durable silicone rubber gaskets Easy installation, innovative Optimized Reflector mode from pure anodized aluminum, the reflector used inside has special coating for high reflectivity and long lifetime with maximum performance. Construction of LED module should be corrosion resistant die-cast aluminum housing designed to act as Heat Sink that can resist high temperature up to 55 degree Celsius and hard weather conditions, LED module should have special reflector optics thus providing excellent glare reduction and its special complex surface reflector technology with efficiency >80% LED module shall possess reflector based optics for smooth and full cut off light distribution with no light above 90 degrees CRI 80 Optimal performance with a glare-free, full cut-off, uniform lighting distribution. LED modale shall have optimized PCB design with touchdown technology. Optimal Performance with a glare -free full cut off, uniform lighting distribution. Excellent heat management operating temperature 5°C to 50°C Fixture should work well in operating temperature ranging from -30°C to +55°C, Ingress Protection IP66, Mechanical Impact resistance: IK08, Electrical Housing is polyester powder coated Corrosion resistant and superior quality finishes for all weather conditions. Mains Current AC 220V-240V 50/60Hz.Esyyshr 35W, Driving mA 700 mA, Driver Included, insulation class 1 4000K having lumen output of 4000 lumens. Dimensions 750mm(length) X 186mm(width) x 120mm(height) as per approved by the Engineer Incharge. |
| 2 | Supply / Fixing of Rectangular pole of height 4.5 mtr made out of MS pipe as per IS 4923. The pole shall be PU painted The pole shall have in built junction box weather proof flush door & locking arrangement for housing at bottom of the pole. Pole shall be made out of 200 mm x 100 mm Rectangular section of thickness 4 mm with base plate dimensions 325x225x16 mm thick. The base plate shall be machined & chamfered all four side by 6 mm ,25x25x3 mm ,angle jacket to be weld at two places all around with base plate , so pole to protect the base plate & pole weld joint. & also give the strength to the pole . The body of the decorative pole shall be painted properly to give it a smooth surface.The pole should have arragement for fixation of the mounting the fitting and the top of the pole should be openable for maintenance of fhe fitting . The decorative pole shall be duly pre-treated ( with phosphating ) & epoxy primer inside & outside of the part and painted in UV ray resistant PU coating in required colour. The coating should have a DFT of 80 micros Average. The pole shall be Powder coated. fhe fitting As per the Approval of E/ in charge. LED FIXTURE Supply/ Fixing of LED fixture in the aluminum special section box of size (Size 120 x 186 x 150 mm). One no SQ LED module 4 LED's for outdoor applications Specific lighting system designed for street/pathway lighting, having Wattage of 35 W LED. Corrosion resistant extruded aluminum aesthetic housing Closed by a toughened optical grade safety glass diffuser and sealed with durable silicone rubber gaskets Easy installation, innovative Optimized Reflector mode from pure anodized aluminum, the reflector used inside has special coating for high reflectivity and long lifetime with maximum performance. Construction of LED module should be corrosion resistant die-cast aluminum housing designed to act as Heat Sink that can resist high temperature up to 55 degree Celsius and hard weather conditions, LED module should have special reflector optics thus providing excellent glare reduction and its special complex surface reflector technology with efficiency >80% LED module shall possess reflector based optics for smooth and full cut off light distribution with no light above 90 degrees CRI 80 Optimal performance with a glare-free, full cut-off, uniform lighting distribution. LED modale shall have optimized PCB design with touchdown technology. Optimal Performance with a glare -free full cut off, uniform lighting distribution. Excellent heat management operating temperature 5°C to 50°C Fixture should work well in operating temperature ranging from -30°C to +55°C, Ingress Protection IP66, Mechanical Impact resistance: IK08, Electrical Housing is polyester powder coated Corrosion resistant and superior quality finishes for all weather conditions. Mains Current AC 220V-240V 50/60Hz.Esyyshr 35W, Driving mA 700 mA, Driver Included, insulation class 1 4000K having lumen output of 4000 lumens. Dimensions 750mm(length) X 186mm(width) x 120mm(height) as per approved by the Engineer Incharge. |
| 3 | Supply/ Fixing of LED fixture in the aluminum special section box of size (Size 120 x 186 x 150 mm). One no SQ LED module 4 LED's for outdoor applications Specific lighting system designed for street/pathway lighting, having Wattage of 35 W LED. Corrosion resistant extruded aluminum aesthetic housing Closed by a toughened optical grade safety glass diffuser and sealed with durable silicone rubber gaskets Easy installation, innovative Optimized Reflector mode from pure anodized aluminum, the reflector used inside has special coating for high reflectivity and long lifetime with maximum performance. Construction of LED module should be corrosion resistant die-cast aluminum housing designed to act as Heat Sink that can resist high temperature up to 55 degree Celsius and hard weather conditions, LED module should have special reflector optics thus providing excellent glare reduction and its special complex surface reflector technology with efficiency >80% LED module shall possess reflector based optics for smooth and full cut off light distribution with no light above 90 degrees CRI 80 Optimal performance with a glare-free, full cut-off, uniform lighting distribution. LED modale shall have optimized PCB design with touchdown technology. Optimal Performance with a glare -free full cut off, uniform lighting distribution. Excellent heat management operating temperature 5°C to 50°C Fixture should work well in operating temperature ranging from -30°C to +55°C, Ingress Protection IP66, Mechanical Impact resistance: IK08, Electrical Housing is polyester powder coated Corrosion resistant and superior quality finishes for all weather conditions. Mains Current AC 220V-240V 50/60Hz.Esyyshr 35W, Driving mA 700 mA, Driver Included, insulation class 1 4000K having lumen output of 4000 lumens. Dimensions 750mm(length) X 186mm(width) x 120mm(height) as per approved by the Engineer Incharge. |
| 4 | Supply / Fixing of SITC of 12 Watt or more LED Bollard for outdoor applications Aesthetic appearance, Corrosion resistant aluminum housing, UV stabilized optical grade acrylic diffusers, Excellent heat dissipation to extend integral component life, Sealed with durable silicone rubber paskets, Easy installation, easy maintenance, Operating temperature 0°C to 50°C, Mechanical Impact resistance: IK08, Electrical Insulation: CLASS I, Housing is polyester powder coated Corrosion resistant and superior quality, finishes for all weather conditions, Colors: HMI to HM6 standard RAL (Optional), Ingress Protection. IP65, Aluminum Frame dimension: 200 x 200 mm and 1000 mm Height, with base plate 350 x 350 x 10 mm thick with 4 holes 18 mm dia for 16 mm dia foundation bolt as per attached drawing/design as per approved by the Engineer Incharge |
| 5 | SITC of concrete embedded Railing LED Light in ground up lighter adjustable IP 67/IK08 as per EN 6059% standards with 3W Led class I protection & CE certified how ng made up of fiberglass nylon with SS AISI 316L frame diffused made up of tempered glass resistant to impact & thermal shock reflector with symmetric profile driver inbuil as per approved by Engineer Incharge. |
| 6 | Preparation of concrete foundation , installation, testing and commissioning and earthing for 6/4.5 M pole.the concrete foundation shall be of size 400 mm x 400 mm x 1000 mm with neccssary excavation,providing & laying in position1:2:4 RCC with laying base concrete 150 mmm thick (1:4:8 i.e.. 1 cement : 4 coarse sand :& graded stone aggregate 40 mm nominal size ). Providing staraightening , cutting bending and placing in position reinforcement column of cold twisted bar of 8 mm dia x 100 mm long (apprx ) x 10 nos. and reinforcementring of cold twisted bar of 8 mm dia x 1600 mm long (apprex) x 8 nos. (with 190mm spacing ) casting RCC 1:2:4 including positioning of foundation bolt (temple)& PVC Tee & PVC pipe of 65 mm dia for cable entry at desire level strictly as per drawing and as per direction of Engineer in Charge as required. |
| 7 | Supply and Laying of 63 mm dia (OD-63 mm & ID-51 mm nominal) DWC HDPE Pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to 14930, Part II complete with fitting and cutting, jointing etc. direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc. complete as required. PSR Bons No.104/CE/EE(E/M)2023, Dated 06- 03-2023 |
| 8 | Supply and fixing following capacity of automatic street light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting of time switch TSO 100 series with contactors, HRC fuses, isolating switch metering instrument & instrument box with CTs etc. in case of TPN, complete in all respect., 40 A TPN |
| 9 | S&F of 6 Amp to 32 Amp. SPMCB (10 KA) C Curve, CAT A |
| 10 | Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc., 25 sq. mm 3-1/2 core |
| 11 | Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc., 16 sq. mm 4 core |
| 12 | Supply and wiring of 1.5 sqmm 3 core 1100 v grade LT control multistand cupper un armoured cable direct in ground including excavation sand cushaning protected covering and refiling the trench etc. as required as per incharge |
| 13 | Supply and fixing of plain or pin type copper tin plated cable socket ( lug ) to the cable leads, insulating with tape and making connection etc. complete in all respect as per direction of the Engineer-Incharge., 10 sq. mm |
| 14 | Supply and fixing of plain or pin type copper tin plated cable socket ( lug ) to the cable leads, insulating with tape and making connection etc. complete in all respect as per direction of the Engineer-Incharge., 16 sq. mm |
| 15 | Supply and fixing of plain or pin type copper tin plated cable socket ( lug ) to the cable leads, insulating with tape and making connection etc. complete in all respect as per direction of the Engineer-Incharge., 25 sq. mm |
| 16 | \\"Supply and burring of Safe Earthing Electrode T-19 (Hot Dip Galvanized), Length up to 2000mm, outer pipe 50mm, inner pipe 25, terminal Dia 12 mm, outer GI pipe of 16 swg and inner GI pipe of 12 swg with Hot Dip Galvanization up to 100 micron filled with crystalline conductive mixture (CCM) having anti corrosive & conductive property with 50 kgs activated soil (BFC) capable of reducing the soil resistivity with good mixture of retaining capacity along with 30cm square C.I. frame with hinged cover & masonry husing (from electrode terminal to switch board, cost of 25 x 3 G.I . strip will be extra) Make: As approved in U.P. P.W.D., & C.P.R.I. Certified. PWD SI No :725 (A)\\" |
| 17 | Supply and laying of 25mm x 3mm G.I. strip from earth electrode directly in the ground as required complete in all respect. |
| 18 | Supply & erection of overhead line with G.I. wire no. 8 to 4 SWG on poles/serivce bracket including binding etc. complete in all respect. |
| 19 | Annual operation and maintenance of LED street light fitting etc all complete (Excluding LED Module, Driver) etc all complete . (1419 Nos x 36 Month = 51084 Month) Please Enable Macros to View BoQ information |
