|
| 1 | CIVIL WORKS |
| 2 | Clearing grass and removal of rubbish upto a distance of 50 m outside the periphery of the area |
| 3 | Earthwork in excavation by mechanical means (hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sq.m on plan) including disposal of excavated earth lead upto 50 m and lift upto 1.5m disposed earth to be leveled and neatly dressed including providing barricading, danger lighting guarding as directed in : All kinds of soil |
| 4 | Earthwork in excavation in trenches for all leads & lifts in all type of strata comprising of any type of materials either in full or part as the case may be adopting any method/methods as may be convenient as permitted excluding blasting in all conditions such as dry, moist, foul, saturated, submerged, etc,. including dressing of sides, planking & strutting, timbering ,ramming of bottom ,pumping and bailing out water ,barricading danger lighting guarding, getting out excavated soil & stacking as directed by Engineer for all leads & lifts etc. complete |
| 5 | Refilling the pipeline/foundation trenches plinth sides, foundation etc. with available excavated earth in layers not exceeding 20 cm depth consolidating each layer ramming and watering lead upto 50 M and all lifts and disposal of surplus earth as directed by Engineer . |
| 6 | Supplying and filling in plinth under floors, trenches including watering ramming consolidating, dressing, complete. Moorum |
| 7 | Disposal of unserviceable materials such as laterite stones, bricks, cement concrete, scrap materials, excess earth by tipper truck or as directed by Engineer in charge including loading, transportation, unloading, levelling etc at the risk and cost of agency / contractor including selection of site for disposal with all lifts and leads etc. all complete. |
| 8 | Rubble packing with hard laterite stone under floors including watering ramming and consolidating etc. in pipeline trenches and other foundations complete. |
| 9 | Providing & laying cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded granitic or basaltic stone aggregate 20 mm. nominal size) excluding cost of centering, shuttering and finishing in: All work up to Plinth level |
| 10 | Providing and laying in position ready mixed concrete (RMC) manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead upto 10kms having continious agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C., from the transit mixer to the site of laying, excluding the cost of centering, shuttering, finishing and reinforcement including the cost of admixtures in recommended porportions as per IS : 9103 to accelerate/retard setting of concrete, improve workability without imparing strength and durability as per the directions of the engineer-in-charge. All works upto floor V level. M-30 grade of concrete |
| 11 | Centering & shuttering including Strutting, Propping & removal of forms for : Foundations, Footings, Bases for columns |
| 12 | Vertical surfaces such as retaing walls, return walls, Partitions, walls (any thickness) including attached Pilasters, Buttresses, Plinth and string courses, Fillets and the like |
| 13 | Columns, Piers, Pillars, Aburments, Posts and struts (square rectangle polygon in plan) |
| 14 | Sides and Soffits of beams, Beam Haunchings, Cantilever, Girders, Bressumers and Lintels plinth beams not exceeding 1m in depth |
| 15 | Suspended floors, roofs landings, shelves & their supports |
| 16 | Centering & shuttering including Strutting, Propping & removal of forms for sloping or battering surface (slabs, beams, louvers, etc) including folded plates. i.Where inclination to the horizontal does not exceed 30° requiring shuttering on the underside only |
| 17 | Providing and laying upto floor five level cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded granitic or basaltic stone aggregate 20 mm nominal size) including smooth finishing to exposed surfaces, with cement mortar 1:3 (1 cement: 3 fine sand) including centering and shuttering etc.String courses, copings, bedplates, anchor blocks, plain window sills and the like. |
| 18 | Providing and fixing weepholes with rigid PVC make laid in position with a required slope and level while layingpipes of approved the concrete of retaining wall,wing wall and earth retainig structure complete as directed by the Engineer in charge |
| 19 | Providing TMT steel reinforcement bars of (SAIL, TATA. VIZAG, JSW Steel Ltd.) ) (Confirming to IS 1786 of 1986) for RCC work (conforming to I.S. 1786 of 1986) including bending, binding & placing in position in all the floors along with the factory made precast concrete cover blocks of specified sizes whose compressive strength is not less than that of surrounding concrete in the structural member. |
| 20 | Providing and laying in position cement concrete 1:2:4 (1 cement : 2 coarse sand: 4 graded granitic or basaltic stone aggregate 40 m nominal size) excluding cost of centering, shuttering and finishing : In retaining walls , return walls(any thk) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping bed blocks, anchor blocks, plain window sills, fillets etc, upto floor five level. |
| 21 | Laterite masonry in neatly dressed stones of size as specified in cement mortar 1: 4 (1 cement : 4 coarse sand) in foundation and basement. |
| 22 | Extra for laterite masonry in all sizes in superstructure from floor I level upto floor V level. |
| 23 | Providing and fixing Exposed Laterite stone of 100 mm thk for Dado ,laid on cement mortar paste 1:4 (1 cement : 4 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the stone including rubbing including applying acrylic Varnish etc complete. as per designs and the directions of the engineer-in-charge. |
| 24 | Providing and fixing M.S. grill of required pattern in wooden frames of Windows etc. with M.S. flats square or round bars with round headed bolts and nuts or by by screws. |
| 25 | Providing and fixing anodized aluminum ventilators (including frame and shutter ) with three partitions with 5 mm thick approved clear float glass in one partition, Exhaust opening in one partition & 6 mm thk glass louvers in one partition with using weight and size of section not less then as specified or as shown in drawing ,locking arrangement,silicon sealant ,EPDM gaskets, including all aluminum fixture and fittings etc. complete . All gaps between civil work and aluminium frames shall be sealed and made watertight by applying silicone sealant.Rectangular tube @0.478kg/m |
| 26 | Providing and and laying vitrified floor tiles in different sizes of Johnson, Somany, Kajaria (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make in colours and shades as specified laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand) including grouting the joints with white cement and matching pigment etc., complete. 600X 600 mm Dark Shades |
| 27 | Providing and laying Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer : Lakha Red |
| 28 | Marble tiles in risers of steps, skirtings, dado, walls and pillars laid on 12 mm (average) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) and jointed with grey cement slurry including rubbing and polishing complete with Kotah stone slab flooring over 20 mm (average thick base of lime mortar 1:1:1 (1 lime putty : 1 surkhi : 1 coarse sand) laid . Plain white Makrana slab 25mm thick |
| 29 | Marble stone flooring with 18 mm thick marble stone (sample of marble shall be approved by Engineer-in-charge) over 20mm (average) thick base of cement Mortar 1:4 (1 cement:4 coarse ) using : white makrana Marble |
| 30 | Providing and laying 300x350x160 mm thick decorative laterite stone flooring (Patradevi stone) laid on 20 mm thick base of cement mortar 1:4 ( 1cement :4 coarse sand ) including maintaining 75 mm gap between two stone for grassing.Gaps to be filled with good earth for grassing. all work completed as per directed by Engineer-in-charge.(Price including stone,gardening soil,fertilizers and grass etc complete). |
| 31 | Supplying and fixing Pre-cast cement concrete kerb-stones(factory made,the factory should be ISO certified and registered under Dirctorate of Industries, Govt. of India) of M-20 with 20 mm nominal size granitic/basaltic aggregate properly consolidated by mechanical plat-form and vibrators with smooth finish including fixing at site complete as per specification. Size 30 cm Lx 40 cm H x 15 cm T |
| 32 | Demolishing laterite stone masonry in cement mortar including stacking of serviceable material & disposal of unserviceable material within 50 mts. lead. |
| 33 | Demolishing R.C.C. work including stacking of steel bars & disposal of unserviceable within 50 steel bars & disposal of unserviceable within 50 |
| 34 | Dismantling the tile work in floors and roofs laid in cement including stacking of materials within 50 meters lead for thickness of tiles 10mm to 25mm. |
| 35 | Providing water proofing treatment over the new R.C.C. roofs terrace toilet by spreading cement slurry over the R.C.C. slab and laying of 10cms. Average laterite stone ballast coba with the necessary gradient for easy flow of rain water and the coba in covered with damp proof of Hindustan water proofing co. Or equivalent jointless water proofing plaster of mix 1:3 ( 1 cement : 3 find sand), finished smooth with wooden trowel with false marking of 30 cms square. The vertical surface of the adjoining walls are to be treated upto a height of 30cms including rounding of junction (the rate includes for complete items including labour and materials and including cost of initial treatment of roof slab as follows. The injunction of damp proof or equivalent compound with cement solution will be given as and when found necessary for filling honey comb, cracks etc. in the R.C.C. slabs). NOTE: cement consumption 25 kg/sq.m. |
| 36 | Providing and fixing concrete roof tiles of Monier brand Elabana series over fabrication structure as per manufacture guidelines, including fixing tiles in standard patterns or as specified by the architect. Colour - Orange |
| 37 | Providing and fixing Monier \\" CONCRETE RIDGES\\" as required over layer of TOPFLEX including all necessary fixtures etc. |
| 38 | Providing and fixing Monier \\" BARGE TILES\\" as required over layer of TOPFLEX including all necessary fixtures etc. |
| 39 | 12mm cement plaster 1:4 (1 cement : 4 fine sand) |
| 40 | 6mm cement plaster to ceiling 1: 3 (1 cement : 3 fine sand) |
| 41 | 18mm cement plaster in two coats under layer 12mm thick cement plaster 1:5 ( 1 cement : 5 coarse sand) and top layer 6mm thick with cement plaster 1: 3 (1 cement : 3 coarse sand) finished with sponge. |
| 42 | Extra for providing and mixing water proofing material proportion recommended by the manufacturers. 12 mm cement Plaster 1 :3 ( 1 cement : 3 sand) |
| 43 | Providing and applying white cement based putty of average thickness 1.00mm of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 44 | Wall painting (two or more coats) with plastic emulsion paint of approved brand and manufacture on new work to give an even shade |
| 45 | Painting three or more coats with acryllic exterior paint of approved brand and manufacture (such as weather shield,APEX) including applying one coat of cement primer and one coat of surface treatment etc. complete. |
| 46 | Providing & fixing 19mm thk plywood work in frames of doors using 19mm marine ply (waterproof) with all hardware,and other frames and fixed in position with 50 mm fastners etc. complete as specified as shown in the drawings. |
| 47 | Providing and fixing first class Indian teak wood moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surfaces etc. 50 x 12 mm |
| 48 | Providing and fixing block board flush door shutters 35mm thick ( 1st Class Teak ply on both faces), laminated on both sides with 1mm thick laminate of approved brand and colour including cost of Adhesive, Nails, screws during fixing etc. complete. |
| 49 | Providing & fixing bright finished Stainless Steel mortise latch & lock with 60 mm Cylinder and a pair of levers, handles with necessary screws etc.complete |
| 50 | Providing and fixing bright finished brass door latch with necessary screws etc complete. 250 x 16x 5mm |
| 51 | Providing and fixing chromium plated brass butt hinges with necessary screws etc. complete Size 125 x 70 x 4.0mm |
| 52 | Providing and fixing 150 mm. bright finished brass floor door stopper with rubber cushion screws etc. to suit shutter thickness complete. |
| 53 | Providing and fixing bright finished brass tower bolts (barrel type) with screws etc. complete |
| 54 | Providing and applying decorative plastering for a window sorrounding, using 1:4 morter mixture with bricks chips,featuring a 300mm offset, and including custom moulding work as details in approved drawings and direction by engineer. (the job involves applying a decorative finish over underlying structure, incorporation special decorative features etc complete. |
| 55 | Providing and applying decorative plastering for double Piller at the corner (Ht 3.50 mt), using 1:4 mortar mixture with brick chips, featuring a 150mm offset, and including custom moulding work as details in approved drawings and direction by the engineer. (the job involves applying a decorative finish over the underlying structure, incorporating special decorative features etc complete. |
| 56 | Providing and applying decorative plastering for Piller at the center (Ht 3.50 mt), using 1:4 mortar mixture with brick chips, featuring a 150mm offset, and including custom moulding work as details in approved drawings and direction by the engineer. (the job involves applying a decorative finish over the underlying structure, incorporating special decorative features etc complete. |
| 57 | Providing and applying decorative plastering for Piller at the center for hall(Ht 2.10 mt), using 1:4 mortar mixture with brick chips, featuring a 200mm offset, and including custom moulding work as details in approved drawings and direction by the engineer. (the job involves applying a decorative finish over the underlying structure, incorporating special decorative features etc complete. |
| 58 | Providing and applying decorative plastering for arch of span of 3mt., using 1:4 mortar mixture with brick chips, featuring a 150mm offset, and including custom moulding work as details in approved drawings and direction by the engineer. (the job involves applying a decorative finish over the underlying structure, incorporating special decorative features etc complete. |
| 59 | Providing and applying decorative plastering for flowers at the ceiling with dia. 1.20mt, using 1:4 mortar mixture with brick chips, featuring a 60mm offset, and including custom moulding work as details in approved drawings and direction by the engineer. (the job involves applying a decorative finish over the underlying structure, incorporating special decorative features etc complete. |
| 60 | Providing and applying decorative plastering ofr cornice at ceiling in hall of ht 0.40mt, using 1:4 mortar mixture with brick chips, featuring a 60mm offset, and including custom moulding work as details in approved drawings and direction by the engineer. (the job involves applying a decorative finish over the underlying structure, incorporating special decorative features etc complete. |
| 61 | Construction and installation 6mt height replica of Shree Suptakoteswar stumb using sadhahalli grey granite stone with intricate carvings, moulding as per drawing. The structure should have 6mt ht. with 2.5 x2.5X0.70 mt ht at base and stumb of 1.50x1.50x5.25 mt height at top as per details drawings and direction by the engineer. |
| 62 | Providing and applying decorative plastering for temple at base sorrounding(Paduka for Plinth), using 1:4 morter mixture with bricks chips,featuring a 150mm height and including custom moulding work as details in approved drawings and direction by engineer etc complete. |
| 63 | Providing and applying decorative plastering for temple at base sorrounding(Padma for Plinth), using 1:4 morter mixture with bricks chips,featuring a max 200mm height and including custom moulding work as details in approved drawings and direction by engineer etc complete. |
| 64 | Providing and applying decorative plastering for temple at base sorrounding(Kumuda for Plinth), using 1:4 morter mixture with bricks chips,featuring a max 200mm height and including custom moulding work as details in approved drawings and direction by engineer etc complete. |
| 65 | Providing and applying decorative plastering for temple at base sorrounding(Adhopadma for Plinth), using 1:4 morter mixture with bricks chips,featuring a max 200mm height and including custom moulding work as details in approved drawings and direction by engineer etc complete. |
| 66 | Providing and applying decorative plastering for temple (Big mantap ), using 1:4 morter mixture with bricks chips,featuring a max 2100mm height and including custom moulding work as details in approved drawings and direction by engineer etc complete (including labours, materials and scaffolding etc) |
| 67 | Providing and applying decorative plastering for temple (Karnakuta ), using 1:4 morter mixture with bricks chips, including custom moulding work as details in approved drawings and direction by engineer etc complete (including labours, materials and scaffolding etc) |
| 68 | Providing and applying decorative plastering for temple (small mantap ), using 1:4 morter mixture with bricks chips,featuring a max 1500mm height ,750mm width, including custom moulding work as details in approved drawings and direction by engineer etc complete (including labours, materials and scaffolding etc) |
| 69 | Providing and applying decorative plastering for temple (Cornice ), using 1:4 morter mixture with bricks chips,featuring a max 300mm height, including custom moulding work as details in approved drawings and direction by engineer etc complete (including labours, materials and scaffolding etc) |
| 70 | Providing and applying decorative plastering for temple (small Statue ), using 1:4 morter mixture with bricks chips,featuring a max 750mm height, including custom moulding work as details in approved drawings and direction by engineer etc complete (including labours, materials and scaffolding etc) |
| 71 | Providing and applying decorative plastering for temple (Big Statue ), using 1:4 morter mixture with bricks chips,featuring a max 1200mm height, including custom moulding work as details in approved drawings and direction by engineer etc complete (including labours, materials and scaffolding etc) |
| 72 | Providing and applying decorative plastering for temple (Adhopadma for sajja), using 1:4 morter mixture with bricks chips,featuring a max 200mm height and including custom moulding work as details in approved drawings and direction by engineer etc complete. |
| 73 | Providing and applying decorative plastering for temple (Cornice above Adhopadma ), using 1:4 morter mixture with bricks chips,featuring a max 300mm height, including custom moulding work as details in approved drawings and direction by engineer etc complete (including labours, materials and scaffolding etc) |
| 74 | Providing and applying decorative plastering for temple (yalli ), using 1:4 morter mixture with bricks chips,featuring a max 300mm height, including custom moulding work as details in approved drawings and direction by engineer etc complete (including labours, materials and scaffolding etc) |
| 75 | ELECTRICAL WORKS |
| 76 | Supply of 3 1/2 core armoured PVC/XLPE insulated, PVC sheathed aluminium conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size.3 1/2 Core 70sq.mm |
| 77 | Supply of 3 core unarmoured PVC/XLPE insulated, PVC sheathed copper conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size.3 Core 1.5 sq.mm |
| 78 | Supply of 3 core unarmoured PVC/XLPE insulated, PVC sheathed copper conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size.3 Core 2.5 sq.mm |
| 79 | Supply of 4 core unarmoured PVC/XLPE insulated, PVC sheathed copper conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size.4 Core 2.5 sq.mm |
| 80 | Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size not exceeding 25 sq.mm in the existing RCC/HUME/STONEWARE Metal pipe, etc. complete as required |
| 81 | Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size exceeding 25 sq.mm but not exceeding 120 sq.mm direct in ground including excavation in the form of a trench as per Cable Trench Drawing provided by the Engineer-Incharge,sand cushioning with screened sand bed of 20mm thick , protective covering with bricks placed breadth-wise on top of cable all over the run( the brick protection shall cover the cable and project atleast 5 cms over the sides of the cable) and backfilling the excavated earth without stones or hard material and making the surface proper with 15 cm crown on the top complete as required.(a) In soily strata |
| 82 | Supplying and making cable end terminations with brass compression gland and aluminium lugs for folowing sizes of 3 1/2 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. 3 1/2 x 70 Sq. mm. |
| 83 | Supplying and fixing following way TPN sheet steel, double door, Horizontal type MCB distribution board 415 V on surface/ recess complete with tinned copper busbar neutral busbar earth bar dinnbar detachable gland plate interconnections phosphotized and powder painted including earthing etc. as required ( but without MCB/RCCB/Isolator)(k) 12 way (8+36), double door, Horizontal type Cat B |
| 84 | Supplying and fixing 40 A, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required.(e) TPN, Cat A |
| 85 | Supplying and fixing 6 A to 32 A, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required. |
| 86 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in recessed PVC conduit(heavy) with modular switch, modular plates, suitable size modular GI box of specified Category and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.Group C -- with Cat B Modular Accessories |
| 87 | Wiring for group controlled light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable (with)in recessed PVC conduit(heavy) and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. |
| 88 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable in the (with) independent recessed PVC conduit(heavy) of appropriate size as required.'b) 2 x 2.5 sq.mm + 1 x 2.5 sq.mm earthwire (20mm Conduit) |
| 89 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable in the (with) independent recessed PVC conduit(heavy) of appropriate size as required.'(c) 2 x 4 sq.mm + 1 x 4 sq.mm earthwire (20mm Conduit) |
| 90 | Supplying and fixing of following sizes of rigid PVC conduit alongwith accessories in surface(medium)/recess(heavy) including cutting the wall and making good the same in case of recessed conduit as required.a) 20 mm |
| 91 | Supplying and fixing of following sizes of rigid PVC conduit alongwith accessories in surface(medium)/recess(heavy) including cutting the wall and making good the same in case of recessed conduit as required.b) 25 mm |
| 92 | Supplying and fixing following modular switch/ socket on the existing modular plate and switch box including connections but excluding modular plate etc. as required (a) 5/6 A switch Cat A |
| 93 | Supplying and fixing following modular switch/ socket on the existing modular plate and switch box including connections but excluding modular plate etc. as required (d) 3 pin 5/6 A socket outlet Cat A |
| 94 | Supplying and fixing following modular switch/ socket on the existing modular plate and switch box including connections but excluding modular plate etc. as required b) 15/16 A switch Cat A |
| 95 | Supplying and fixing following modular switch/ socket on the existing modular plate and switch box including connections but excluding modular plate etc. as requiredd) 6 pin 15/16 A socket outlet Cat A |
| 96 | Supplying and fixing modular blanking plate on the existing modular plate switch box excluding modular plate etc. as requireda) Cat A |
| 97 | Supplying and fixing following size modular GI box alongwith modular base and cover plate for modulator switches in recess etc. as required(a) 1 or 2 Module ( 75 mm x 75 mm) Cat A |
| 98 | Supplying and fixing following size modular GI box alongwith modular base and cover plate for modulator switches in recess etc. as requiredb) 4 Module ( 125 mm x 7 mm) Cat A |
| 99 | Supplying and fixing following size modular GI box alongwith modular base and cover plate for modulator switches in recess etc. as required(c) 6 Module (200mm x 75 mm) Cat A |
| 100 | Supplying and fixing following size modular GI box alongwith modular base and cover plate for modulator switches in recess etc. as requiredSITC of Wall Fan,600 mm Sweep, with all accessories. |
| 101 | Supply installation testing and commissioning of 8-10 W Spot light COB IP65 Light with System efficacy of 100 lm/W.L70 life of 50000 Hrs. P.F.>0.95 with THD<10% ,CCT 5700 K,CRI 70,Surge Protection 4 Kv. Input voltage range of 120V to 300V.Certification:- LM79 & LM80 test report should be from govt approved Inhouse NABL lab/ government of India authorised Make Havells/Wipro/Phillips/ Legaaro/Bajaj as required and directed by engineer incharge |
| 102 | Supply installation testing and commissioning of W 80W Flood light IP65 Light with System efficacy of 100 lm/W.L70 life of 50000 Hrs. P.F.>0.95 with THD<10% ,CCT 5700 K,CRI 70,Surge Protection 4 Kv. Input voltage range of 120V to 300V.Certification:- LM79 & LM80 test report should be from govt approved Inhouse NABL lab/ government of India authorised Make Havells/Wipro/Phillips/ Legaaro/Bajaj as required and directed by engineer incharge |
| 103 | Supplying & erecting of LED 20W tube light fitting (4 feet) with aluminium housing, heat sink, integrated HF electronic driver complete.(Includes suspension accessories). Make: Philips, Reytek, Leska, Crompton, Wipro, Havells as required as directed by the Engineer In-charge |
| 104 | SITC of Decorative Chandelier having Finest crystals in chrome finish, Material -Mirror stainless steel, Dimensions (mm) -Dia. =600x1500(H),Lamp Base- G9, Wattage- 7x42W Max, complete with all accessories. |
| 105 | SITC of Decorative Chandelier having Finest crystals in chrome finish, Material -Mirror stainless steel, Dimensions (mm) -Dia. =1200x1500(H),Lamp Base- G9, Wattage- 12x42W Max, complete with all accessories. |
| 106 | Supply and erecting of 48 inch ( 1200mm sweep) ceiling fan, double ball bearing type, , complete with all accessories. (b) Cat B |
| 107 | Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required (a) Cat A |
| 108 | Earthing with GI earth pipe 2 mts long 40 mm dia medium class with ISI mark,of approved brands, including accessories and providing masonry enclosure with CI/RCC cover having locking /lifting arrangement and watering pipe etc. with charcoal or coke and salt) as required as per the Earthing Drawing provided by the EngineerIncharge.The scope of work includes the following: a) Excavation of pit of size 1.0x1.0x 2.0 mtrs(min) and disposal of excavated soil. b) Class B GI pipe, 40mm diameter as per specifications. c) Charcoal/salt as per specs ( paid seperately). d) Refilling the pit of size 1.0x1.0x 2.0 mtrs(min) with soft black soil of minimum resistivity i/c transportation. e)Masonary chamber with proper foundation, cover plate and locking arrangement. f) Testing of earth value with earth megger and certifications of its value. Aluminium tag with embossed earthing value to be attached to the pipe. g)watering arrangement(plumbing will be paid seperately). |
| 109 | SITC of 12W multi color spot light, Protection Rating : IP66, complying to BIS standard \\"IS 10322 (Part 5/Sec 1): 2012\\" and having CE certification against standard \\"Low Voltage Directive & Protective Equipment - EN 60598-1:2015\\", and \\"Electromagnetic Compatibility Directive - EN 61547: 2009\\", Mounting Structure : Adjustable wall mount yoke arrangements for fixing the lights. Power consumption : 12W, CCT : RGBW, (as per the design approval) Optics : PMMA with holder, Beam Angle : 25º/45º/60º, Control : DmX512 Channel : 4 CH, Body : Die casted / extruded aluminium with embossed manufacturer logo, Seperate compartment for keeping the decoder/driver in the housing, Hot spot and light distribution : Optics Designed to minimize hot spots & fringing in color mixing applications. Power Input : DC 24V with external driver, Surge Protection : Inbuilt surge protection 2KV-4KV(Additional if required will be added as per the requirement), Toughened transparent glass having the IK protection up to IK05, Painting : Chemical 3/7 tank processed treatment before the powder coat black/ash/approved color coat. Fixture will be suitable to operate in a temperature range of 0°C to 50°C , LED life should be at least 50,000 burning hours at L70 at 25 degree centigrade. Luminaire is inclusive of Integral male/female waterproof connectors with structures in pre wired conditions as per IS standard. PCB thickness must be 1.6mm, 35 micron Copper, 2W TC with Black or White masking, Copper /OSP finish. LM79, IK05, IP66, HV Certificates from NABL Acrediated laboratory. LED Makes should be CREE, LumilLED, Osram, Seoul, Nichia or equivalent with the engineer or 3rd party testing laboratory approval. Power & DMX Loop In/Out along with IP67 connector having the length >400mm. |
| 110 | SITC of high quality long through multi color Linear wash light, Protection Rating : IP66, complying to BIS standard \\"IS 10322 (Part 5/Sec 1): 2012\\" and having CE certification against standard \\"Low Voltage Directive & Protective Equipment - EN 60598-1:2015\\", and \\"Electromagnetic Compatibility Directive - EN 61547: 2009\\", Mounting Structure : Adjustable surface mount yoke arrangements for fixing the lights. Power consumption : 80W, CCT : RGBW(6000-7000K), (as per the design approval), Optics : PMMA with holder, Beam Angle : 25º/45º/60º, Control : DmX512 Channel : 4 CH, Body : Die casted / extruded aluminium with embossed manufacturer logo Separate compartment for keeping the decoder/driver in the housing which can be easily removable for service without disturbing the LEDs/Optics, Hot spot and light distribution : Optics Designed to minimize hot spots & fringing in color mixing applications. Power Input : Constant DC 24V with external driver to the constant current decoder, Surge Protection : Inbuilt surge protection in the driver 2KV-4KV(Additional if required will be added as per the requirement), Toughened transparent glass having the IK protection up to IK07, Painting : Chemical 3/7 tank processed treatment before the powder coat black/ash/approved color coat. Fixture will be suitable to operate in a temperature range of 0°C to 50°C, The light fixtures are having IP68 air vent made of stainless steel which helps to desiccate & prevent from forming moisture inside the light fixture at worst environmental condition. LED life should be at least 50,000 burning hours at L70 at 35 degree centigrade. Luminaire is inclusive of Integral male/female waterproof connectors with structures in pre wired conditions as per IS standard. PCB thickness must be 1.6mm, 35 micron Copper, 2W TC with Black or White masking, Copper /OSP finish. LM79, IK07, IP66, HV Certificates from NABL Acrediated laboratory. LED Makes should be CREE, LumilLED, Osram, Seoul, Nichia or equivalent with the engineer or 3rd party testing laboratory approval. Power & DMX Loop In/Out along with IP67 connector having the length >300mm. |
| 111 | SITC of high quality Multi Color Neon Flexible light, Protection Rating : IP65, Mounting Structure : Adjustable wall mount SS clips for fixing the lights. Power consumption : 12W, CCT : RGB/RGBW, (as per the design approval) Beam Angle : 120º, Control : DmX512 Channel : 4 CH, Power Input : DC 24V with external driver, Surge Protection : Inbuilt surge protection 2KV-4KV(Additional if required will be added as per the requirement), Fixture will be suitable to operate in a temperature range of 0°C to 50°C , LED life time should be at least 50,000 burning hours at L70 at 25 degree centigrade. Luminaire is inclusive of Integral male/female waterproof connectors with structures in pre wired conditions as per IS standard. LED Makes should be CREE, LumilLED, Osram, Seoul, Epistar, Nichia or equivalent with the engineer or 3rd party testing laboratory approval. |
| 112 | SITC of high quality long through multi color wash light, Protection Rating : IP66, complying to BIS standard \\"IS 10322 (Part 5/Sec 1): 2012\\" and having CE certification against standard \\"Low Voltage Directive & Protective Equipment - EN 60598-1:2015\\", and \\"Electromagnetic Compatibility Directive - EN 61547: 2009\\", Mounting Structure : Adjustable surface mount yoke arrangements for fixing the lights having the rotation degrees embosed in the die cast. Power consumption : 50W, CCT : RGBW(6000-7000K), (as per the design approval), Optics : PMMA with holder, Beam Angle : 25º/45º/60º, Control : DmX512 Channel : 4 CH, Body : Die casted / extruded aluminium with embossed manufacturer logo, Seperate compartment for keeping the decoder/driver in the housing which can be easily removable for service without disturbing the LEDs/Optics, Hot spot and light distribution : Optics Designed to minimize hot spots & fringing in color mixing applications. Power Input : Constant DC 24V with external driver to the constant current decoder, Surge Protection : Inbuilt surge protection in the driver 2KV-4KV(Additional if required will be added as per the requirement), Toughened transparent glass having the IK protection up to IK08, Painting : Chemical 3/7 tank processed treatment before the powder coat black/ash/approved color coat. Fixture will be suitable to operate in a temperature range of 0°C to 50°C, The light fixtures are having IP68 air vent made of stainless steel which helps to desiccate & prevent from forming moisture inside the light fixture at worst environmental condition. LED life should be at least 50,000 burning hours at L70 at 35 degree centigrade. Luminaire is inclusive of Integral male/female waterproof connectors with structures in pre wired conditions as per IS standard. PCB thickness must be 1.6mm, 35 micron Copper, 2W TC with Black or White masking, Copper /OSP finish. LM79, IK07, IP66, HV Certificates from NABL Acrediated laboratory. LED Makes should be CREE, LumilLED, Osram, Seoul, Nichia or equivalent with the engineer or 3rd party testing laboratory approval. Power & DMX Loop In/Out along with IP67 connector having the length >300mm. |
| 113 | SITC of Aluminium Profile for Neon flex |
| 114 | SITC of DC power driver for the above Lights, Power : 200W, Input : AC 110-240V AC, 50Hz, Output : DC 12/24V, Protection rating, IP67, Surge protection : LL 4KV, LE 6KV |
| 115 | SITC of high quality DMX decoder, Power Input : DC 24V |
| 116 | SITC of PVC insulated multi core electrical un armoured flexible 5C x 0.5Sq mm power cable having less electrical losses. (As per actuals depending upon the site condition) |
| 117 | SITC of 5 core DMX cable comprises twisted pairs with shield support for carrying of data. DMX512 cable is used for connecting all light consoles that use DMX 512 standard data transmission. (As per actuals depending upon the site condition) |
| 118 | SITC of 50 mm outside dia. double wall corrugated pipes (DWC) for enclosing cable below ground/road surface, to required depth complete for both power and Dmx. (As per actuals depending upon the site condition) |
| 119 | SITC of IP65 \\"I\\" power connectors having 3/4 pole cable connector, chuck type strain relief, Current rating 20 A rms continuous, Easy and extremely precise locking system \\"Quick Lock\\" High impact materials - long-lasting and reliable |
| 120 | SITC of IP65 \\"I\\" DMX connectors having 3/5 pole cable connector, Male/Female connector with improved latch, cage type contacts, \\"solder stop\\" for easy soldering, and additional ground contact for best contact integrity between chassis and cable connector. More durable housing for maximum reliability. |
| 121 | SITC of 5 pin XLR Male connectors having 5 pole cable connector, Male/Female connector with improved latch, cage type contacts, \\"solder stop\\" for easy soldering, and additional ground contact for best contact integrity between chassis and cable connector. More durable housing for maximum reliability. |
| 122 | SITC of 5 pin XLR Female connectors having 5 pole cable connector, Male/Female connector with improved latch, cage type contacts, \\"solder stop\\" for easy soldering, and additional ground contact for best contact integrity between chassis and cable connector. More durable housing for maximum reliability. |
| 123 | SITC of Power Distribution Board made up of MS Sheet metal fabricated housing black powder coated and ivery connectors for the internal terminations and external outgoing connecting points, fibre / brass glands of suitable size fitted MCB control for outgoing circuits. Timer with required contactor for auto switching. Power panel suitable for indoor/outdoor applicable and floor mount / wall mount options.- 12 Nos of 6/10A SP Outgoing MCB's.- 1No of 32A TPN Incoming MCB. |
| 124 | SITC of IP driver box made up of PVC / UPVC and ivory connectors for the internal terminations and external outgoing connecting points, fiber / brass glands of suitable size fitted MCB control for outgoing circuits. |
| 125 | SITC of DMX isolator or splitter provides Isolated optical DMX splitter provides 8 outputs from a 1 input and Input voltage: AC 110 to 220 V, 50 Hz, Product features: Group 1 & group 8 DMX signal change. |
| 126 | SITC of Din Rail Mount DMX controller can be used to control a wide variety of different DMX systems- from RGB/RGBW to more advanced moving and color mixing luminaires, DMX audio players and fountains. The controller comes with a variety of features, iPhone/iPad/Android remote control, Wi-Fi facilities, dry contact port triggering and flash memory.USB connection • 1024 DmX channels universe in live mode (computer) • 8 dry contact trigger ports via HE10 connector • stand alone mode with 5 area and 90+ scenes, Mac OSx 10.6/10.7/10.8 - Windows XP/VISTA/SEVEN/8 32/64 bits and USB 2.0, XLR3, mini USB, 1 HE10, Power From 5V to 5.5V DC (AC/DC adapter in option. |
| 127 | SITC of Programming charges |
| 128 | SITC of additional accessories for installing the lights as per the final drawing/site condition consisting of clamps, brackets, angles, conduits, joints, hardware's like fasteners, nut & bolts etc., |
| 129 | Street Light Panel: Supply, Installation, testing and commissioning of LT panel IP- 67 outdoor type,floor mounted Panel, shall be suitable for 415 V, 3 phase, 4 wire, 50Hz Supply system. With 3 phase energy meter and 100A TPN MCB as incommer and 11 nos of TPN MCB as outgoing with 3 numbers of microcontoller based programmable digital Almac timer as directed by engineer in-charge Please Enable Macros to View BoQ information |
