|
| 1 | Description and specification of items of work to be executed (complete work) |
| 2 | Earth work in excavation by manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. |
| 3 | Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. |
| 4 | Providing and laying in position cement concrete of specified grade 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) excluding the cost of centering and shuttering |
| 5 | Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete |
| 6 | Centering and shuttering including strutting, propping etc. and removal of form for Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. |
| 7 | Reinforced cement concrete work 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement |
| 8 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe 500D or more. |
| 9 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: 6.1.1 Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 10 | Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20mm nominal size derived from natural sources). |
| 11 | Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it thereafter .The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineer in- charge .The elevational area of the scaffolding shall be measured for payment purpose .The payment will be made once irrespective of duration of scaffolding. |
| 12 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes |
| 13 | Structural steel work riveted, bolted or welded in built up sections, trusse and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 14 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 15 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture |
| 16 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. |
| 17 | Providing and fixing PUF (Polyurethane Foam) panel 80/50 mm including all accessories, fittings, labour, and T&P. |
| 18 | Providing ridges or hips of width 60 cm overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete. 0.80 mm thick with zinc coating not less than 275 gm/m² |
| 19 | Providing and fixing of 75mm thick cement wall Panels of reputed brand/birla/everest along with GI channels/framework and all accessories i.e. screws,nuts,bolts,fastners jointing with cement based adesive/mortar/sealent etc. complete as per the direction of Engineer-in-charge. |
| 20 | Providing 12 mm cement plaster of Mortar : 1:6 (1 cement: 6 fine sand) |
| 21 | Providing and laying Vitrified tiles in floor in 600x600mm sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size of Tile 600 x 600 mm |
| 22 | Providing and fixing ceramic/vitrified wall tiles of approved shade, size, and make on cement wall panels, including cleaning and leveling of the surface and improve bonding, applying polymer-modified cementitious tile adhesive conforming to IS 15477:2019 with a notched trowel at 3-5 mm thickness, pressing tiles firmly into the adhesive bed with proper alignment and spacers for uniform joints, filling joints with polymer-modified cement grout or epoxy grout of approved shade, and finally cleaning and polishing the tile surface after completion, all complete as per specifications. |
| 23 | Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre |
| 24 | Finishing walls with ready mixed Premium acrylic emulsion paint (Company Depot Tinted) having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade with silicon additives on New work (Two or more coats applied @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm. |
| 25 | Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two coats |
| 26 | Providing and fixing aluminium work for doors, windows, ventilators andpartitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, Paneling and dash fasteners to be paid for separately For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron) |
| 27 | Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides |
| 28 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) |
| 29 | \\"Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. Upto 5 mm depth and 5 mm width\\" |
| 30 | Providing and fixing Brass 100 mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete. |
| 31 | Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. complete as per direction of Engineer-in-charge Polyester powder coated minimum thickness 50 micron aluminium |
| 32 | Providing and fixing stainless steel (SS 304 grade) adjustable friction windows stays of approved quality with necessary stainless steel screws etc. to the side hung windows as per direction of Engineer-in-charge complete. |
| 33 | Providing and fixing anodized aluminum grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment). |
| 34 | \\"Providing and fixing false ceiling at all heights including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer?s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.45.4 Fully Perforated Gypsum Plaster Board of size 1200 x 2400x12.5 mm having approx. 15 % perforated area with perforation size and pattern as approved by the Engineerin- charge and as per manufacturer?s specification, with all 4 sides tapered and backed by acoustical tissue with NRC value not less than 0.60\\" |
| 35 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. completeat all levels. Granite stone slab colour black, Cherry/Ruby red Area of slab upto 0.50 sqm |
| 36 | Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge (Granite Work) |
| 37 | Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. |
| 38 | Providing valleys of 90 cm wide overall in plain G.S. sheet fixed with polymer coated J, or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete and 1.60 mm thick with zinc coating not less than 350 gm/m² |
| 39 | \\"Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: (a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. (b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. (c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.\\" |
| 40 | Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required: and W.C. pan with ISI marked white solid plastic seat and lid |
| 41 | Polyethylene water storage tank with cover and suitable locking arrangement |
| 42 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete and Flexible pipe 40 mm dia |
| 43 | Providing and fixing beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick (Size 1m X 1m) |
| 44 | \\"Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require, White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap\\" |
| 45 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. |
| 46 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. (25 mm nominal dia Pipes) |
| 47 | \\"Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. (50 mm nominal dia Pipes)\\" |
| 48 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. (15 mm nominal bore) |
| 49 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 (15 mm nominal bore) |
| 50 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. (15 mm nominal bore) |
| 51 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 52 | Provide and fixing of uPVC Waste Pipe 100 MM with necessary T, Corner and joints with chemical to fix and seal inclusve of all labours for surface dressing and leveling, covering etc. complete |
| 53 | Provide and fixing of uPVC Waste Pipe 150 MM with necessary T, Corner and joints with chemical to fix and seal. inclusve of all labours for surface dressing and leveling, covering |
| 54 | Providing and fixing of electrical article: Pvc Pipe (25mm) |
| 55 | Providing and fixing of electrical article: PVC Pipe Bend |
| 56 | Providing and fixing of electrical article: Junction Box |
| 57 | Providing and fixing of electrical article: Gi Electric Fan Box J Clip |
| 58 | Providing and fixing of electrical article: FLUSH METAL BOXES 12M |
| 59 | Providing and fixing of electrical article: FLUSH METAL BOXES 8M |
| 60 | Providing and fixing of electrical article: FLUSH METAL BOXES 4M |
| 61 | Providing and fixing of electrical article: FLUSH METAL BOXES 2M |
| 62 | Providing and fixing of electrical article: FLUSH METAL BOXES 1M |
| 63 | Providing and fixing of electrical article: Havells 12 M Cover Plate |
| 64 | Providing and fixing of electrical article: Havells 8M H Cover Plate |
| 65 | Providing and fixing of electrical article: Havells 4M Cover Plate |
| 66 | Providing and fixing of electrical article: Havells Crabtree Athena 2M Cover Plate |
| 67 | Providing and fixing of electrical article: Havells 1M Cover Plate |
| 68 | Providing and fixing of electrical article: Suntech 12 Way SPN Metal White Double Door Distribution Board MCB Box |
| 69 | Providing and fixing of electrical article: PVC Insulated 6 mm Single Core Flexible Copper Wires & Cables polycab /crompton/hevells |
| 70 | Providing and fixing of electrical article: PVC Insulated 2.5mm Single Core Flexible Copper Wires & Cables polycab /crompton/hevells |
| 71 | Providing and fixing of electrical article: PVC Insulated 1.5mm Single Core Flexible Copper Wires & Cables polycab /crompton/hevells |
| 72 | Providing and fixing of electrical article: PVC Insulated 1 mm Single Core Flexible Copper Wires & Cables polycab /crompton/hevells |
| 73 | Providing and fixing of electrical article: Polycarbonate Bulb Holder for Wall |
| 74 | Providing and fixing of electrical article: Havells Crabtree Athena 5 Step Fan Regulator - 2 Module |
| 75 | Providing and fixing of electrical article: Havells Crabtree Athena 6A Five Pin Socket |
| 76 | Providing and fixing of electrical article: Havells Crabtree Athena 6A One-Way Switch (White) |
| 77 | Providing and fixing of electrical article: Havells Crabtree Athena 6A-16A Three Pin Combined Shutter Socket |
| 78 | Providing and fixing of electrical article: Havells Crabtree Athena 16A One-Way Switch with Indicator (White) |
| 79 | Providing and fixing of electrical article: Havells DHMGCDPF032 PVC Plastic 32A MCB DP C Curve (White) |
| 80 | Providing and fixing of electrical article: Havells 32A Single Pole MCB, Multi, Standard (HA-SPMCB32) |
| 81 | Providing and fixing of electrical article: Jaset Innovations Chipboard Screw with Saw Thread and Nylon Wood Dowel – White Zinc Plated – Flat Pozidriv Counter Sunk Head – Assorted Small Sizes – Pack of 258 pcs |
| 82 | Providing and fixing of electrical article: Havells Ventil Air DX 200mm Exhaust Fan (White) |
| 83 | Providing and fixing of electrical article: led Light/ 600X600 MM false ceiling light |
| 84 | Providing and fixing of electrical article: Projection concdealed light LED - |
| 85 | Providing and fixing of electrical article: Havells/Crompton Fan 3 Blades Ceiling Fan |
| 86 | Providing and fixing of electrical article: Fiber Cement Board, for cover the pipe 600x600x6 mm |
| 87 | Providing and fixing of electrical article: Adhesive for fixing FCB |
| 88 | Providing & fixing Spot light branded |
| 89 | Labour Charges for Providing and fixing of electrical article from Sl. No. 53 to Sl. No. 87 |
| 90 | Providing and installing cassette type air conditioners of 2 Ton capacity each, 5 Star rated, with 360° cooling, complete with supply of units, copper refrigerant piping with insulation, condensate drain piping, electrical cabling with MCB/ELCB protection, ceiling suspension rods and MS frame supports, outdoor unit mounting on MS stand with anti-vibration pads, including all fittings, labour, testing and commissioning, using approved make such as Godrej/Daikin/Mitsubishi/LG/Voltas/Hitachi/O General/Lloyd or equivalent. |
| 91 | Providing and installing window type air conditioners of 1.5 Ton capacity each, 5 Star rated make such as Godrej/Daikin/Mitsubishi/LG/Voltas/O General/Hitachi/Llyod or equivalent. |
| 92 | Supply and installation new 25 ltr geyser Crompton/usha/hindware/orient/bajaj/havells in inspection room toilet. |
| 93 | Providing and fixing ACP sheet 4mm at Porta Cabin Window and Chajja including frame work, labour etc. complete. |
| 94 | Providing and fixing double Mosquito Jalli over window at outer portion of Porta Cabin window including fixing, labour etc. complete |
| 95 | Providing and fixing window roller blinds with all necessary fitting etc. complete. |
| 96 | Providing and fixing Porta Cabin Door panel size (0.90m x 2.05m) including MS door jamb (50x50x6)mm with M.S gate panel having M.S angle iron frame size (40x40x5)mm with Iron sheet 16 guage including lock, latch,kabja,Hinges/Hole pass etc. all fitting including paint, etc. complete. |
| 97 | Supply and installation of CCTV Hikvision/Dahua HD NVR Night color 5 No. 5 MP IP CCTV camera with HDD 2TB Hard disk, 16 CH. DVR with all wiring including poe switches, RJ 45 connectors ,HDMI output,etc . with all accessories complete. |
| 98 | Excavating, supplying, stacking and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in foundation trenches, plinth, sides of foundation etc. complete for all lift. |
| 99 | Providing and laying brick tile edge flooring in composite mortar 1:4 (1 cement, 4 coarse sand) over bed of 20mm thick mortar including filling of joints. Curing all complete. |
| 100 | Repair and fixing of kept damaged GI pipe railing 80mm nominal size above dwarf wall including fixing of additional GI pipe 80mm nominal dia at base after cutting damaged/decayed leg etc. complete |
| 101 | Supply and installation of display LED TV 42'' (LG/Samsung) with all fittings complete. |
| 102 | Supply and installation at site of readymade Dustbins of Red Sand Stone of Cylindrical shape in single block having top molding and depression as per design on extra surface fully open top outer top dia 580mm and height 750mm of required shape & design including fixing in cement concrete with providing inner bins of hard PVC of removable nature to insert under the red sand stone dustbin of size 580mm dia and 750mm height. |
| 103 | Tile brick masonry with common burnt clay F.P.S. (non modular) tile bricks of class designation 10 in superstructure above plinth level up to floor V level in cement mortar 1:6 (1 cement : 6 coarse sand). |
| 104 | Providing lakhori/tile brick masonry in composite mortar the ratio 1:1:1 (1 lime 1 surkhi 1 sand) etc. complete. |
| 105 | Provision for providing and applying lime pointing after racking out joints in composite mortar 1:1:1 (1 lime 1 surkhi 1 sand) including curing etc. complete. |
| 106 | Providing cement plaster 12mm thick with cement mortar ratio 1:4 (1 cement : 4 fine sand). |
| 107 | Repair of Baradari MS Door panel size aprx. (1.45M x 2M) including removal and re fixing after installation of new hole pass/chul set/Hinges all necessary repair ,cutting, welding, straightening, labour charges etc. complete. |
| 108 | Repair of Main mosque MS double Door size aprx. (2.50M x 2.25M) including removal and re fixing after installation of extra MS plate at base ,missing MS plate,bars,new hole pass/chul set/Hinges all necessary repair ,cutting, welding, straightening, , labour charges etc. complete. |
| 109 | Repair of Small Moti mosque MS double Door size aprx. (1.45M x 2M) including removal and re fixing after installation of new missing bars, new hole pass/chul set/Hinges all necessary repair ,cutting, welding, straightening, paint work, labour charges etc. complete. |
| 110 | Providing and laying lime concrete in the ratio of 1:1:1:4(1u. lime 1 surkhi, 1 c.sand and 4 brick agg.)25 mm nominal size etc. complete. |
| 111 | Providing and fixing of new MS gate aprx. Size 0.90mx2m having MS angle iron 50x50x6 with 16 mm square bar spacing 10 cm etc complete . |
| 112 | Removal and re-fixing of existing M.S revolving gate size aprx. 0.90m x 1m height after necessary repair etc. complete |
| 113 | Providing and fixing of new MS ventilation window aprx. Size 0.70mx0.45m having MS plate 25x3 etc complete . Please Enable Macros to View BoQ information |
