|
| 1 | Excavation in trenches in soft and loose soil n.exc 1.5 mtr wide and n.exc. 1.5 mtr depth for laying and taking out of electric power cable and getting out all as specified and directed by engineer –in-charge. Note: (i) Digging shall be carried out by manual means only.(ii) During the excavation damage of Road, Electric cable, Signal Cable should be rectified by the contractor without any extra cost. |
| 2 | Returning filling in including spreading leveling watering and well ramming in layers not exceeding 25 cm thick all as specified and directed. |
| 3 | Removing excavated material not exceeding 50 mtr away and depositing where directed at a level n. exc 1.5 mtr above the starting point . |
| 4 | M & L for caulking of lead joint of spigot and socket cast iron pipe incl providing lead wool and making joint leak proof including necessay earth work/excavation and making good disturbed site, T & P and draining out water etc of following as directed. |
| 5 | 150 mm bore |
| 6 | 100 mm bore |
| 7 | Taking up GI pipe steel tubing from trench/walls etc including all fittings for following bore of pipe: |
| 8 | 80 mm bore |
| 9 | 50 mm bore |
| 10 | 40 mm bore |
| 11 | 25 mm bore |
| 12 | 20 mm bore |
| 13 | S & F to wall/trenches GI steel tubing medium grade including all fittings such as Tees, elbow, bends etc for following bore of pipe complete all as specified : |
| 14 | 80 mm bore |
| 15 | 50 mm bore |
| 16 | 40 mm bore |
| 17 | 25 mm bore |
| 18 | 20 mm bore |
| 19 | S&F sluice valve cast iron both ends flanged class PN-1.6 conforming to IS-14846 with stainless steel spindle including joints & jointing materials (Rubber gasket, nut, bolts,washers etc) complete of following sizes : |
| 20 | 150 mm bore |
| 21 | 100 mm bore |
| 22 | Taking up DI pipe from trench etc including all fittings for following bore of pipe: |
| 23 | 150 mm bore |
| 24 | 100 mm bore |
| 25 | Supplying, laying, jointing and testing Ductile Iron Pipes special class- K7 ISI marked (IS-8329-2000 Reaffirmed - 2005 Eddition 4.1) suitable for push on joints supplied with rubber gaskets, with sockets and cement mortar lining and metallic zinc coating inside and with finishing layer of bitumenous paint outside, without polyethelene sleeve but including Push on joint supplied with EPDM (Ethylene Propylene Dience Monomer) rubber gasket conforming to IS 5382-1985 (reaffirmed-2003) with dual hardness of type 2 (bulb) and type-5 (Heel) quality, laid in trenches all as specified and as directed complete of following size:- |
| 26 | 150 mm bore |
| 27 | 100 mm bore |
| 28 | Supply and fixing DI special as bends (any type radius and angle), tappers any type (straight bend increasing or decreasing or double socket) tee pieces single branch 'Y' junction double branch cross collars caps plug upto 250mm bore for DI Pipes complete all as specified and as directed. |
| 29 | S & F in repair Gun metal gate valve iron wheel head screwed both ends for GI steel tubing suitable for following bore of pipe |
| 30 | 50 mm bore |
| 31 | 40 mm bore |
| 32 | 25 mm bore |
| 33 | 20 mm bore |
| 34 | S & F in repair GI water tank connector plug both ends for GI steel tubing suitable for 25 mm bore of pipe as per direction of Engr-in-Charge. |
| 35 | S & F in repair GI union ISI marked of following size as per direction of Engr-in-Charge : |
| 36 | 25 mm bore |
| 37 | 20 mm bore |
| 38 | S & F in repair GI elbow ISI marked of following size as per direction of Engr-in-Charge :- |
| 39 | 25 mm bore |
| 40 | 20 mm bore |
| 41 | S&F in replacement of water pressure gauge of Bourden’s type upto 150 mm dia with pressure range of 0 to 10 Kg/Sqcm on rising main water supply line including fixing arrangement , GI tubing nipple stop cock making holes by drilling and welding of socket complete all as specified. |
| 42 | S&F in repair fully automatic Phase adjuater/Phase corrector with suitable relay and suitable for 5 to 20 HP Centrifugal pump with motor connected with, 415 volt, 50 HZ AC supply all as specified and directed by Engr-In-Charge. |
| 43 | S&F in repair fully automatic Single phase preventor with suitable relay and suitable for 5 to 20 HP Centrifugal pump connected with, 415 volt, 50 HZ AC supply all as specified and directed by Engr-In-Charge. |
| 44 | Dismantling of Pump motor including suction and delivery connection from pump without damage and servicing of Pump with replacement of both side bearing, bronze impeller, alingment of shaft ,replacement rubber coupling, replacement of Nut and bolt and replacement of suction and delivery flange with existing size bend and finishing the pump body surface and painting of pump and motor with super enamelled paint and reassembling the pump and motor with starter and suction ,delivery pipe including testing complete for the following capacity:- |
| 45 | 20 HP Pump and Motor |
| 46 | 15 HP Pump and Motor |
| 47 | 10 HP Pump and Motor |
| 48 | 7.5 HP Pump and Motor |
| 49 | 2 HP Mono Block Pump |
| 50 | 1 HP Mono Block Pump |
| 51 | Supply and fix in replacement fully automatic electronic type 415 Volts star delta starter complete of following capacity all as directed by Engineer-in-Charge. |
| 52 | 20 HP Star Delta Starter |
| 53 | 15 HP Star Delta Starter |
| 54 | 10 HP Star Delta Starter |
| 55 | 7.5 HP Star Delta Starter |
| 56 | Rewinding of centrifugal/monoblock pump/motor after disconnecting motor from pump and dismantling the motor, taking down burnt winding wire of field coil and rewinding of field coil for suitable size of super enameled copper winding wire with necessary insulation materials including replacement of motor bearing of both NDE & DE sides with pump and necessary connection etc all as specified and directed as per following size:- |
| 57 | 15 HP |
| 58 | 10 HP |
| 59 | 7.5 HP |
| 60 | 7.5 HP |
| 61 | Supply and fix in replacement fully automatic electronic type single phase 230 Volts DOL Starter complete of following capacity all as directed by Engineer-in-Charge. |
| 62 | 2 HP Motor |
| 63 | 1 HP Motor Please Enable Macros to View BoQ information |
