|
| 1 | Checking of LT Panel/Motor/Pump set for detecting any kind of fault and attending the fault immediately at any time round the clock and carry out certain repairs required as per site requirement and replacing of worn out parts by expert engineer complete all as direced.Note :- Unit rate includes detecting of any kind of fault in LT Panel/Motor/Pump set only and cost of replacement of worn out parts shall be measured and paid separately under respective items of BOQ. |
| 2 | Supply and fix in replacement starter for 2 HP to 3 HP submersible pump, confirming to IS/ IEC 60947-4-1, IP-54, 230 Volt, Single Phase, with inbuilt amp & voltage meter, Rugged MU-2P contactor with wide band voltage, MU-2P Relay for reliable overload protection, heavy duty START & RUN condensers with FRLS internal wiring, and class H insulation complete all as specified and directed by engr-in-charge. |
| 3 | Supply and fix in replacement Direct online starter for 5HP submersible pump, confirming to IS/ IEC 60947-4-1, IP-54,415 Volt, extended wide band coil with FRLS internal wiring, star type-Air break and class H insulation complete all as specified and directed by engr-in-charge. |
| 4 | Supply and fix in replacement fully automatic star delta starter for 10 HP submersible pump, confirming to IS/ IEC 60947-4-1, IP-54,3 phase, 415 Volt, 50 Hz, relay range 6-10 amps type MK1, with FRLS internal wiring and class H insulation complete all as specified and directed by engr-in-charge. |
| 5 | All as per item No 4 above but 12.5 HP |
| 6 | All as per item No 4 above but 15 HP |
| 7 | All as per item No 4 above but 20 HP |
| 8 | All as per item No 4 above but 25 HP |
| 9 | Supply and fix in replacement 3 Pole Power contactors type MNX with AC coil, rating 32 Amps, conforming IS/ IEC 60947-4-1, IP-20,415 Volt, snap fit construction, nut retaining washer for quick termination and class H insulation complete all as specified and directed by engr-in-charge. |
| 10 | All as per item No 9 above but 95 Amp |
| 11 | All as per item No 9 above but 150 Amp |
| 12 | All as per item No 9 above but 185 Amp |
| 13 | S&F in repair thermal over load relay type MN suitable for MNX contactors relay range 90-150 Amps including fixing arrangement complete all as specified and directed. |
| 14 | All as per item No 13 above but 22 to 32 Amps |
| 15 | Dismantling of defective submersible pump set 01 to 03 HP with column assembly, pump bowl assembly of any size/capacity including disconnecting electrical and water line connection complete with lifting it with the help of chain pulley, clamp tripod and reassembling after repairing by lathe work and other machinery work as required and replacement of studs, nuts, bolts etc including re-fixing the same after making it serviceble in its existing position complete all as specified and directed. |
| 16 | All as per item No 15 above but pump set capacity 10-20 HP |
| 17 | All as per item No 16 above but pump set capacity 25 HP.Note :- After taking out submersible pump set for repair the contractor shall cover tube will with cap to avoid any accident. |
| 18 | Dismantling of 01 to 03 HP Capacity defective submersible pump of any make and M&L for repairing of submersible pump of including gun metal impeller, intermidiate bowl, rubber bush, neck ring, pump shaft and pump shaft key, bearing etc as required to make serviceable ncluding testing and refixing the same in existing position complete all as specified and directed.complete as directed |
| 19 | Dismantling of 10 to 20 HP Capacity defective submersible pump of any make and M&L for repairing of submersible pump of including gun metal impeller, intermidiate bowl, rubber bush, neck ring, pump shaft and pump shaft key, bearing etc as required to make serviceable ncluding testing and refixing the same in existing position complete all as specified and directed.complete as directed |
| 20 | Dismantling of 25 HP Capacity defective submersible pump of any make and M&L for repairing of submersible pump of including gun metal impeller, intermidiate bowl, rubber bush, neck ring, pump shaft and pump shaft key, bearing etc as required to make serviceable ncluding testing and refixing the same in existing position complete all as specified and directed.complete as directed |
| 21 | Dismantling of 01 to 03 HP Capacity defective submersible motor any make, cutting and taking out burnt out winding wire and M&L for rewinding the same with PVC insulated water proof conductor copper wire of best quality of existing gauge & turn and reassembling after replacement of bush, bearing, sleeves, grinding as required and polishing of rotor shaft, Bush/bearing/sleeve/thrust plate etc including testing and refixing the same in existing position complete all as specified and directed. |
| 22 | Dismantling of 10 to 20 HP Capacity defective submersible motor any make, cutting and taking out burnt out winding wire and M&L for rewinding the same with PVC insulated water proof conductor copper wire of best quality of existing gauge & turn and reassembling after replacement of bush, bearing, sleeves, grinding as required and polishing of rotor shaft, Bush/bearing/sleeve/thrust plate etc including testing and refixing the same in existing position complete all as specified and directed. |
| 23 | Dismantling of 25 HP Capacity defective submersible motor any make, cutting and taking out burnt out winding wire and M&L for rewinding the same with PVC insulated water proof conductor copper wire of best quality of existing gauge & turn and reassembling after replacement of bush, bearing, sleeves, grinding as required and polishing of rotor shaft, Bush/bearing/sleeve/thrust plate etc including testing and refixing the same in existing position complete all as specified and directed. |
| 24 | S&F in repairs submersible cable PVC insulated copper conductor 2.5 Sqmm 3 core 1100 volts grade complete all as specified and directed |
| 25 | All as per item No 24 above but 4 Sqmm. |
| 26 | All as per item No 24 above but 6 Sqmm. |
| 27 | M&L for 30mm bore, adopter nipple 50 cm long GI flanged or socketed (for connecting column pipe to pump) complete all as specified and directed. |
| 28 | All as per item No 27 above but 50mm bore. |
| 29 | All as per item No 27 above but 80 mm bore. |
| 30 | All as per item No 27 above but 100mm bore. |
| 31 | Supply and install submersible pump borewell 1.5 HP capacity complete as specified and directed |
| 32 | Supply and packing pea gravel of 02 mm to to 06 mm size of the appoved quality as ordered to pack around the casing / slotted pipes in bore well complete all as specified and directed. |
| 33 | Developing tube wells by compressed air with minimum pressure of 10kg/Sqcm and minimum air discharge 450 CFM all as specified in IS 11189-1985 Para 4.3 complete all as specified and directed.Note : Compressor, pump, pipe and other allied items will be arranged by contractor and no extra payment will made by the department. |
| 34 | S&F MCCB 4 Pole, 415 V, fixed type, 25 to 100 Amps with breaking capacity 36 KA |
| 35 | S&F MCCB 4 Pole, 415 V, Adjustable type, 160 Amps with breaking capacity 36 KA |
| 36 | S&F MCCB 4 Pole, 415 V, Adjustable type, 250 Amps with breaking capacity 36 KA |
| 37 | S&F MCCB 4 Pole, 415 V, Adjustable type, 350 Amps with breaking capacity 36 KA |
| 38 | S&F MCCB 4 Pole, 415 V, Adjustable type, 400 Amps with breaking capacity 36 KA |
| 39 | S&F MCCB 4 Pole, 415 V, Adjustable type, 630 Amps with breaking capacity 36 KA |
| 40 | S&F in repair single phase preventor for protection for submersible pump against over loading, reverse phase, single phasing complete all as specified and directed. |
| 41 | Taking up centrifugal pump set from its foundation at different location of installations by disconnecting electrically and machnically, transporting it to the workshop for dismantling the pump sets and back to installation after repairing/removing of unserviceable parts. |
| 42 | 150 HP Capacity |
| 43 | 100 to120 HP Capacity |
| 44 | 30 HP Capacity |
| 45 | 20 HP |
| 46 | 10 to 15 HP Capacity |
| 47 | upto 5 Hp Capacity |
| 48 | M & L for re-winding of electric motor of centrifugal pump sets 3 phase 415 volts 50 Hz AC with super enamelled copper winding wire of existing weight & size incl cleaning of stator slot winding paper fixing startor incl cut x size warnshing and baking , repair to rotot assembly, ball bearing etc all as required to make it serviceable complete all as specified & directed by Engr-in-Charge for capacity :- |
| 49 | 150 HP Capacity |
| 50 | 100 to120 HP Capacity |
| 51 | 30 HP Capacity |
| 52 | 20 HP |
| 53 | 10 to 15 HP Capacity |
| 54 | upto 5 Hp Capacity |
| 55 | Repairing/overhauling of centrifugal pump set incl cleaning, Oiling greshing, gland packing filling and proper allignment incl repair/replacement ball bearing, impller, gland busg, neck ring, cupling, pump shaft key, rubber bush, nut bolts and washer etc all as required to make it serviceable complete and fixed at location as directed for capacity:- |
| 56 | 150 HP Capacity |
| 57 | 100 to120 HP Capacity |
| 58 | 30 HP Capacity |
| 59 | 20 HP |
| 60 | 10 to 15 HP Capacity |
| 61 | upto 5 Hp Capacity |
| 62 | M&L painting of centrifugal pump set complete all as specified and directed by Engr - in - Charge for the capacity:- |
| 63 | 150 HP Capacity |
| 64 | 100 to120 HP Capacity |
| 65 | 30 HP Capacity |
| 66 | 20 HP |
| 67 | 10 to 15 HP Capacity |
| 68 | upto 5 Hp Capacity |
| 69 | Taking out and dismantling of defective jockey pump set of 12.5 HP (Cap 10.8 cum / Hr Cap) with column assembly, pump bowl assembly, Gun metal Impeller, Intermediate Bowl, CI Impeller (Neck Ring), Bowl Bush Rubber/Gun Metal, etc Parts, including disconnecting electrical and water line connection complete with lifting it with the help of chain pulley, clamp tripod and reassembling after repairing by lathe work and other machinery work as required and replacement of studs, nuts, bolts and other defected parts etc including re-fixing the same after making it serviceble in its existing position complete all as specified and directed. |
| 70 | M&L for earthing complete with galvanized steel earth plate electrode 600 x 600 x 6mm size, buried directly in ground (earth pit not less than 3.25M deep below normal ground level) with top edge of the plate not less than 1.5M below normal ground level connected to and including galvanized steel earth strip 32 x 6mm, including 40mm bore GI light grade protection pipe as earth lead strip connected to the earth plate by means of GI bolts, nuts, washers and earth plate surrounded by 150mm thick alternate layers of charcoal or cock dust & common salt, 20mm bore medium grade GI watering pipe, cover 50mm thick of precast RCC, GI wire mesh, GI sheet funnel necessary excavation in soft/loose soil and deposited the surplus soil to a distance n.exc 50 mtr away from starting point complete all as specified and shown in electrical plate No 3 of MES standard schedule of rates 2009 Part-I complete all as specified and directed by Engr-in-Charge |
| 71 | Supply and fixing UPVC column pipe 30 mm bore 12 Kg working pressure standard grade for pump set including plastic rope for supporting of submersible motor necessary fitting and connection to submersible pump complete all as specified and directed. |
| 72 | All as per item No. 47 above but 50 mm bore |
| 73 | All as per item No. 47 above but 80 mm bore |
| 74 | All as per item No. 47 above but 100 mm bore |
| 75 | Supply and fixing plastic rope 25 mm for supporting of submersible motor with necessary fitting and connection to submersible pump complete all as specified and directed. |
| 76 | Supply and fixing plastic rope10 mm for supporting of submersible motor with necessary fitting and connection to submersible pump complete all as specified and directed. |
| 77 | Supply, laying testing, connecting XLPE armoured, LT 1100V grade (heavy duty) copper conductor cable,of following sizes confirming to IS7098(Part-I) 1988, laid in existing RCC covered duct/Sub way/along wall/MS bracket. Note : The Cables shall be fixed to LT panel with suitable size brass/stain less steel cable glants, copper lugs and rate deemed to be included in rate quoted for respective cable. |
| 78 | 3 Core 95 Sqmm |
| 79 | 1 Core 70 Sqmm |
| 80 | Supply and fixing in repair of Manual Changeover switch 630 Amps ,4 Pole ,I-O-II operation supplied with bridging bars,extended shaft and IP65 pistol type handle with SS Enclosure and make electric connection complete all as specified and as directed. |
| 81 | S&F connection plate of motor (star delta) for capacity- |
| 82 | 150 HP Capacity |
| 83 | 100 to120 HP Capacity |
| 84 | 30 HP Capacity |
| 85 | 20 HP |
| 86 | 10 to 15 HP Capacity |
| 87 | upto 5 Hp Capacity |
| 88 | S&F copper lugs of size 70 sqmm complete all as directed |
| 89 | Supply, fabrication and fixing of MS equal angel/MS channel/angel C section etc conforming to GDE FE 410- W as hip and jack rafter, purlins,ladder etc where connected to common rafters and running rails fixed with other connecting plates etc including nut, bolts fastners, necessary welding, cutting etc and two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engr-in-Charge Please Enable Macros to View BoQ information |
