|
| 1 | Repair to potholes any depth, not exceeding 1 sqm each including sweeping free from dust and mud, or water, scoring sunken surfaces in roads, paths, etc., cutting around edges to at least 30 mm in depth making good by applying tack coat with cationic bitumen emulsion RS-1 grade at the rate of 3 kg per 10 sqm of surface, putting in premix as specified for thin bituminous carpet and sealed with liquid seal coat, applying evenly binder (using paving bitumen) @ 9.8 kg per 10 Sqm binding with 6.3 mm size stone chippings @ 0.09 cum per 10 sqm and rolled to a uniform smooth surface with 8 to 12 tonne power roller (including supply of premix binder and aggregate) complete all as specified and directed. |
| 2 | Scarifying or picking gravelled, macadam or bituminous macadam surfaces in area not exceeding 400 sqm, depth exceeding 50 mm but not exceeding 100 mm complete all as specified and directed. |
| 3 | M & L for 7.5 cm thick (compacted thickness) WBM, with coarse aggregates of granite, trap or basalt of grading 2 (63 to 45 mm size) or of grading 3 (53 to 22.4 mm size), spread, rolled and compacted to required gradient and camber with three wheel-power roller of 80 to 100 kN capacity or an equivalent vibratory roller complete all as specified and directed. |
| 4 | M & L except materials for 7.5 cm thick (compacted thickness) WBM, with coarse aggregates of granite, trap or basalt of grading 2 (63 to 45 mm size) or of grading 3 (53 to 22.4 mm size), spread, rolled and compacted to required gradient and camber with three wheel-power roller of 80 to 100 kN capacity or an equivalent vibratory roller complete all as specified and directed. |
| 5 | Preparing unsurfaced water bound macadam surfaces by brushing with wire brushes for removing caked mud etc., sweeping with brooms and finally fanning the cleaned surface with gunny bags or compressed air to remove all loose dirt etc. complete all as specified and directed. |
| 6 | Preparing existing black top surfaces by brushing with wire brushes for removing caked mud etc., sweeping with brooms and finally fanning the cleaned surface with gunny bags to remove all loose dirt etc. complete all as specified and directed. |
| 7 | M&L for applying a tack coat of cationic bitumen emulsion (RS1) conforming to IS: 8887 at a rate of application of 0.20- 0.30kg/ sqm on bituminious surface as specified in Table- 500-3 of MoRTH specifications for road and bridge work 2013, using mechanical sprayer after cleaning of existing surface complete all as specified and directed . |
| 8 | Material and labour for providing premixed bituminous macadam laid/rolled and compacted to required gradient and camber using 8 to 10 tone capacity power roller (consolidated thickness 75mm or less) using paving bitumen (VG 30 Grade) @ 4% by weight of total mix complete all as specified and directed. Note:- (i) The exact bitumen content required shall be determined Mix Design procedure and approved by GE. The adjustment in rate on MINUS side variation in quantity of bitumen if any shall be priced at the rate of ₹70 per kg. No claim whatsoever shall be made for adjustment in plus side. (ii) Bituminous macadam shall be laid using self propelled hydrostatic paver finisher and preparation of mix shall be using hot mix plant and transporting the mix in tipper. |
| 9 | Material and labour for bituminous premixed semi-dense asphaltic concrete, 40mm consolidated thickness using 5.5% paving bitumen (VG 30 Grade) binder content any penetration by weight of total mix, mixed in central computerized hot mix plant and laid using mechanical self propelled paver and rolled and compacted with 8 to 12 tonne power roller to uniform surfaces with required camber and gradient complete all as specified and as directed.Note:- Semi dense asphaltic bituminous concrete shall be designed as per design mix. Contractor shall quote his unit rate considering the bitumen contents as 5.5 %. Any variation in binder content on minus side shall be adjusted at the rate of ₹70.00 per KG of binder. No adjustment in price shall be made if the variation is on plus side. |
| 10 | M&L for preparation of new or previously treated surfaces to receive thermostatic paint and applying road marking with hot applied thermoplastic compound with reflectorizing glass beads on bituminious surface 2.50mm thick including reflectorizing glass beads @ 250gms/ sqm area as per IRC: 35- 1997 and finished the surface in proper level, uniform, free from steaks and holes complete all as specified and directed. |
| 11 | S & F in repair metal tubular delineators (road way indicators) made out of ABS round body fitted with 2 Nos of 65 mm dia highly reflective reflectors made out of PMMA and mounted on 45/50 mm mild steel pipe of 600 mm height duly power coated and thermo plastic elastomers 3 bands of green, red and yellow reflector radium tape of 25 mm wide strip with anti theft steel net for reflector protection including embedded 200 mm below ground level including excavation and PCC M15(Nominal Mix) (150x150x300mm) with using 20 mm graded stone aggregate in foundation and making good surface complete all as specified and directed. |
| 12 | S&F in repair water proof solar road delineator pole mounted (pole size 48mmx1000mm duly powder coated) fixing the same in M-15 grade type B-1 PCC block of size 20x20x30cm deep complete all as specified and directed. |
| 13 | Supply and fixing in repair cat eye solar reflective type of metal body alloy of size 100mm x 100mm x 20mm with PAMA striplens reflector of odel No. DA 972.0 fixed with and incl MS stud of suitable size as per manufactures instructions complete all as specified and directed. |
| 14 | All as per item No 13.00 here-in-before, but taking down carefully from road surface incl cleaning, stacking and re-fixing with suitable adhesive in the same location or any other area of road surface after road marking paint etc complete all as specified and directed. |
| 15 | Supply and fixing in repair solar cat eye aluminum alloy shall (100% water proofing design according to 65) of size 125mm x 125mm x 25mm (shank 65mm) of high efficiency Mono rystafie solar panel 2.4V/ 0.3 watt one NI-ed rechargeable battery (1.2V/ 1600MA) consisting of super bright LED with 10,000 to 18,000 mcd, 3 pieces each side and total 6 pieces are used for high brightness and backup for 12 hours completed as per manufactures instructions etc complete all as specified and directed. |
| 16 | All as per item No 15.00 here-in-before, but taking down carefully from road surface incl cleaning, stacking and re-fixing with suitable adhesive in the same location or any other area of road surface after road marking paint etc complete all as specified and directed. |
| 17 | M & L for 100 mm spread thickness, moorum in granular sub base or light wearing surfaces, spread, rolled and compacted using vibratory roller of 80 to 100 kN static weight with plain or pad foot drum to required gradient and camber complete all as specified and directed. |
| 18 | S&F in replacement double legged informatory sign board of area exc 1.50sqm bu not exc 2.00 sqm fixed on single frame, both side and meeting back to back on the stainless steel 50x50x3.65mm size square pipe 3.20m long of 304 grade, the boards are of high intensity grade retro reflecting sheeting made out of 2mm thick alcoban sheet / aluminium composite panel sheet conforming to IS 736, colour as approved by GE on stainless steel square pipe of size 50x50x3.65mm with nuts, bolts and washers, The lettering will be computerised cut of high intensity grade white sheeting and mechanically fixed on both side board over stainless steel vertical post having 02 Nos flat iron 40x5mm stripes 0.30m long at bottom anf fixed with and including PCC M- 10 type C- 1 in post holes of size 0.45x0.45x0.75m complete all as specified and directed. |
| 19 | S&F in repairs Double Legged informatory Sign Board of Size area exc 1.50 sqm but not exc 2.0 sqm fixed on single frame, both side and meeting back to back on the stainless steel 50x50x3.65mm size, the boards are of high intensity grade retro-reflactive sheeting made out of 2mm thick alcoban sheet/aluminium composite pannel sheet confirming IS 736 colour as approved. The lettering will be computarised cut of high intensity grade sheeting and mechanically fixed both side board ete complete all as specified and directed. |
| 20 | S&F in repair traffic convex mirror of of 80cm dia having 130 degree viewing angle made of polycarbonate material , brim and back holding plate is made of metal/FRB along with pole mounted brackets and pole 60mm dia, min height 1.5m made with galvanised steel pipe (medium grade) duly painted with two coats of synthetic enamel paint over a coat of red oxide primer fixed to the ground by means of PCC 1:2:4 type B2 (using 40mm dia graded stone aggregate) in foundation/filling (size 50cmx50cmx60cm) all as specified and directed. |
| 21 | All as per item No. 20 here- in- before but taking down carefully and refixing after adjustment and repair to make it functional etc and fixed to the ground by means of PCC 1:2:4 type B2 (using 40mm dia graded stone aggregate) in foundation/filling (size 50cmx50cmx60cm) all as specified and directed. |
| 22 | S&F in repair speed breaker of size 750mm X250 mm X75mm made out of ABS material with two highly reflective reflectors moulded in PMMA materials welded with ABS plate through ultrasonic welding process fixed on to the speed breaker so the dust and water can not touch reflectors inside and fixed complete all as specified and directed. Please Enable Macros to View BoQ information |
