Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Items: |
| 2 | Providing Supply and installation of CORNER SINK TABLE -Size :-1100mm L x 1100mm D x 900mm H construction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge , Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agency having NABL accreditation. Dimensions : W= 900 mm, D = 900 mm, H = 875 mm Configurations: 1 Shutter - 1 Nos MOC: MSCRCA: IS – 513 (1994) •Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk. Finish: Powder coating pure epoxy, thickness 40-50 microns , followed with 9 tank Pre Treatment process The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle : Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit)•Hinge: SS Hinge Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. PP Sink,Polypropylene Molded Sinks: Made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Sink - Bowl size to be a minimum of (L x W x D) 560 x 355 x 300 mm. Faucet - 3-way type faucet as per approved make WorkTop : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. (Make as Per Selection of Architect Or Selection Of Higher Authority) |
| 3 | Providing supply and installation of CORNER TABLE - Size 1100mm L x 1100mm D x 900mm H construction: Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge , Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agency having NABL accreditation. Dimensions: W= 900 mm, D = 900 mm, H = 875 mm Configurations: 1 Shutter - 1 Nos MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk. Finish: Powder coating pure epoxy, thickness 40-50 microns , followed with 9 tank Pre Treatment process The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge : SS Hinge Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profile. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. Work Top : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfer and smoothed. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. (Make as Per Selection of Architect Or Selection Of Higher Authority) |
| 4 | Providing supply and installation of ISLAND TABLE - Size :-4880 mm L x1540mm D x 900mm H with Electrical trunkingConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agency Dimensions: W=600 mm, D = 530mm, H = 875 mm Configurations: Storage - 600 W 1 Drawer + 2 Shutter - 8 Nos , Leg space - 6 Nos , Corner leg space - 2 Nos MOC: MSCRCA: IS – 513 (1994) Thickness : LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degrease, Zinc phosphates) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating. Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profile. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings. Worktop : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfer and smoothed. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. (Make as Per Selection of Architect Or Selection Of Higher Authority) |
| 5 | Providing supply and installation of ISLAND TABLE Size :-4880mm L x1540mm D x 900mm H with 2 tier fixed type reagent rack having integrated electrical switch sockets Construction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, D = 530mm, H = 875 mm Configurations: Storage - 600 W 1 Drawer + 2 Shutter - 8 Nos , Leg space - 6 Nos , Corner leg space - 2 Nos MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degrease, Zinc phosphates) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profile. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920.Fixed-Type reagent shelves :It should be complete modular design consisting of 2 stage horizontal storage shelves made of CRCA MS with pure epoxy powder coating and having cutouts for electrical switches and sockets.ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.Worktop : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfer and smoothed. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. (Make as Per Selection of Architect Or Selection Of Higher Authority) |
| 6 | Providing supply and installation of ISLAND TABLE Size :-6080mm L x1540mm D x 900mm H with 2 tier fixed type reagent rack having integrated electrical switch socketsConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, D = 530mm, H = 875 mm Configurations: Storage - 600 W 1 Drawer + 2 Shutter - 10 Nos , Leg space - 8 Nos , Corner leg space - 2 NosMOC: MSCRCA: IS – 513 (1994)Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degrease, Zinc phosphates) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit)Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profile. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920.Fixed-Type reagent shelves :It should be complete modular design consisting of 2 stage horizontal storage shelves made of CRCA MS with pure epoxy powder coating and having cutouts for electrical switches and sockets.ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.Worktop : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfer and smoothed. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. (Make as Per Selection of Architect Or Selection Of Higher Authority) |
| 7 | Providing supply and installation of WALL TABLE - Size :-1280mm L x750mm D x 900mm H with Electrical trunking with 2 tier fixed type reagent rack having integrated electrical switch socketsConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, D = 530mm, H = 875 mm Configurations: Storage - 600 W 1 Drawer + 2 Shutter - 1 Nos , Corner leg space - 1 NosMOC: MSCRCA: IS – 513 (1994)Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degrease, Zinc phosphates) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit)Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profile. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920.Fixed-Type reagent shelves :It should be complete modular design consisting of 2 stage horizontal storage shelves made of CRCA MS with pure epoxy powder coating and having cutouts for electrical switches and sockets.ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.Worktop : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfer and smoothed. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. (Make as Per Selection of Architect Or Selection Of Higher Authority) |
| 8 | Providing supply and installation of WALL TABLE - Size :-2780mm L x750mm D x 900mm H with Electrical trunking with 2 tier fixed type reagent rack having integrated electrical switch socketsConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, D = 530mm, H = 875 mm Configurations: Storage - 600 W 1 Drawer + 2 Shutter - 2 Nos ,leg space - 1, Corner leg space - 1 NosMOC: MSCRCA: IS – 513 (1994)Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degrease, Zinc phosphates) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit)Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profile. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920.Fixed-Type reagent shelves :It should be complete modular design consisting of 2 stage horizontal storage shelves made of CRCA MS with pure epoxy powder coating and having cutouts for electrical switches and sockets.ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.Worktop : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfer and smoothed. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness.(Make as Per Selection of Architect Or Selection Of Higher Authority) |
| 9 | Providing supply and installation of WALL TABLE - Size :-3640mm L x750mm D x 900mm H with Electrical trunkingConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, D = 530mm, H = 875 mm Configurations: Storage - 600 W 1 Drawer + 2 Shutter - 3 Nos , Leg space - 2 Nos , Corner leg space - 1 NosMOC: MSCRCA: IS – 513 (1994)Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degrease, Zinc phosphates) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit)Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profile. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920.ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.Worktop : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfer and smoothed. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness.(Make as Per Selection of Architect Or Selection Of Higher Authority) |
| 10 | Providing supply and installation of WALL TABLE - Size :-3640mm L x750mm D x 900mm H with Electrical trunking with 2 tier fixed type reagent rack having integrated electrical switch socketsConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, D = 530mm, H = 875 mm Configurations: Storage - 600 W 1 Drawer + 2 Shutter - 3 Nos , Leg space - 2 Nos , Corner leg space - 1 NosMOC: MSCRCA: IS – 513 (1994)Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degrease, Zinc phosphates) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit)Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profile. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920.Fixed-Type reagent shelves :It should be complete modular design consisting of 2 stage horizontal storage shelves made of CRCA MS with pure epoxy powder coating and having cutouts for electrical switches and sockets.ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.Worktop : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfer and smoothed. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness.(Make as Per Selection of Architect Or Selection Of Higher Authority) |
| 11 | Providing supply and installation of WALL TABLE - Size :-5260 mm L x750mm D x 900mm H with Electrical trunkingConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, D = 530mm, H = 875 mm Configurations: Storage - 600 W 1 Drawer + 2 Shutter - 4 Nos , Leg space - 2 Nos , Corner leg space - 2 NosMOC: MSCRCA: IS – 513 (1994)Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degrease, Zinc phosphates) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit)Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profile. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920.ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.Worktop : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfer and smoothed. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness.(Make as Per Selection of Architect Or Selection Of Higher Authority) |
| 12 | Providing supply and installation of WALL TABLE - Size :-7210mm L x750mm D x 900mm H with Electrical trunkingConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, D = 530mm, H = 875 mm Configurations: Storage - 600 W 1 Drawer + 2 Shutter - 6 Nos , Leg space - 6 Nos .MOC: MSCRCA: IS – 513 (1994)Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degrease, Zinc phosphates) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit)Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profile. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920.ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.Worktop : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfer and smoothed. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness.(Make as Per Selection of Architect Or Selection Of Higher Authority) |
| 13 | Providing supply and installation of WALL TABLE - Size :-8710mm L x750mm D x 900mm H with Electrical trunking with 2 tier fixed type reagent rack having integrated electrical switch socketsConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, D = 530mm, H = 875 mm Configurations: Storage - 600 W 1 Drawer + 2 Shutter - 7 Nos , Leg space - 6 Nos , Corner leg space 750W - 1 NosMOC: MSCRCA: IS – 513 (1994)Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degrease, Zinc phosphates) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit)Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profile. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920.Fixed-Type reagent shelves :It should be complete modular design consisting of 2 stage horizontal storage shelves made of CRCA MS with pure epoxy powder coating and having cutouts for electrical switches and sockets.ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.Worktop : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfer and smoothed. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness.(Make as Per Selection of Architect Or Selection Of Higher Authority) |
| 14 | Modular Furniture Providing ,Supplying and fixing of Class Room 2 Seater Desk cum Bench For (Junior Class Room) Size (1040 x 1008D x 750H) As per below specification including erection at site Desk-Top Panel -All panels are made from 18mm thk Pte-laminated twin board (E1/P2 GRADE) with PVC edge banding on all sides.The panels have corners-rounded for safety usage. Desk-Top Panel-All panels are made from 18mm thk Pte-laminated Compact Laminated Board with Decorative Paper on both sides (AS PER IS 2046: 1995) The Panels have corners rounded for safety usage .Under structure - All side metal frames and cross connectors are made from combination of 25.4 x1.2 mm thk(approx. 18 SWG) Round ERW tubes ,31.8 x 1.2 mm thk(approx. 18 SWG) Round ERW tubes and 28.6 x 1.2 mm thk(approx. 18 SWG) Round ERW tubes(As per IS:7138) which are welded together.The Welded structures and cross connectors are coated with min. 45 micron thickness of epoxy polyester coating.Back supports which are provided at the rear back are made of 50.8 x 25.4 x 1.2 mm thk(approx. 18 SWG) rectangular ERW tubes(As per IS:7138).The tubes are coated with min. 45 micron thickness of epoxy polyester coating.The storage shelves are made from 0.6 mm thk MS sheet(As per IS:513) fixed below the radesk top panel and are coated with min. 45 micron thickness of epoxy polyester coating. Hooks are provided on the vertical side frames on both sides of the desk for hanging bags/bottles. They are made from 2 mm thk MS sheet(As per IS:513) and are coated with min. 45 micron thickness of epoxy polyester coating.The under structure is assembled using M6 trilobular screws(As per DIN 7500)with Zn blue plating.Compact Laminate seat and back panels are assembled using M6 Counter sunk Trilobular screws(as per DIN 7500) with Zn Black Plating (As per IS 1573:1986)Spacers Are provided on th top of round tubes for wooden panels fixing. They are made of made Glass filled (30%)Plastic Caps made of PP co polymer(3530 Grade) are also provided on the rear frames adding more aesthetic value to the product.M6 high tensile TVS make bolt(Class 8.8) with glass filled nylon level adjusters are provided at the bottom of under structure to take care of unevenness in floor with height adjustment of approx 15mm. Furniture Complete as directed by engineer incharge.(Make :- Godrej Interio, or equivalent (Make & System is as Per Selection of Consultant or Selection of Higher Authority) |
| 15 | Providing ,Supplying and fixing of Class Room 3 Seater Desk cum Bench For (Junior Class Room) (1540 x 1008 x 750) As per below specification including erection at site Desk-Top Panel-All panels are made from 18mm thk Pte-laminated twin board (E1/P2 GRADE) with PVC edge banding on all sides.The panels have corners-rounded for safety usage.Desk-Top Panel-All panels are made from 18mm thk Pte-laminated Compact Laminated Board with Decorative Paper on both sides (AS PER IS 2046: 1995) The Panels have corners rounded for safety usage .Under structure - All side metal frames and cross connectors are made from combination of 25.4 x1.2 mm thk(approx. 18 SWG) Round ERW tubes ,31.8 x 1.2 mm thk(approx. 18 SWG) Round ERW tubes and 28.6 x 1.2 mm thk(approx. 18 SWG) Round ERW tubes(As per IS:7138) which are welded together.The Welded structures and cross connectors are coated with min. 45 micron thickness of epoxy polyester coating.Back supports which are provided at the rear back are made of 50.8 x 25.4 x 1.2 mm thk(approx. 18 SWG) rectangular ERW tubes(As per IS:7138).The tubes are coated with min. 45 micron thickness of epoxy polyester coating.The storage shelves are made from 0.6 mm thk MS sheet(As per IS:513) fixed below the radesk top panel and are coated with min. 45 micron thickness of epoxy polyester coating. Hooks are provided on the vertical side frames on both sides of the desk for hanging bags/bottles. They are made from 2 mm thk MS sheet(As per IS:513) and are coated with min. 45 micron thickness of epoxy polyester coating. The under structure is assembled using M6 trilobular screws(As per DIN 7500)with Zn blue plating.Compact Laminate seat and back panels are assembled using M6 Counter sunk Trilobular screws(as per DIN 7500) with Zn Black Plating (As per IS 1573:1986)Spacers Are provided on th top of round tubes for wooden panels fixing. They are made of made Glass filled (30%)Plastic Caps made of PP co polymer(3530 Grade) are also provided on the rear frames adding more aesthetic value to the product.M6 high tensile TVS make bolt(Class 8.8) with glass filled nylon level adjusters are provided at the bottom of under structure to take care of unevenness in floor with height adjustment of approx 15mm.Furniture Complete as directed by engineer incharge.(Make :- Godrej Interio, or equivalent (Make & System is as Per Selection of Consultant or Selection of Higher Authority) |
| 16 | Providing ,Supplying and fixing of Class Room 2 Seater Desk cum Bench For (Senior Class Room) Size (1240 x 1008D x 850H) As per below specification including erection at site Desk-Top Panel-All panels are made from 18mm thk Pte-laminated twin board (E1/P2 GRADE) with PVC edge banding on all sides.The panels have corners-rounded for safety usage. Desk-Top Panel-All panels are made from 18mm thk Pte-laminated Compact Laminated Board with Decorative Paper on both sides (AS PER IS 2046: 1995) The Panels have corners rounded for safety usage .Under structure - All side metal frames and cross connectors are made from combination of 25.4 x1.2 mm thk(approx. 18 SWG) Round ERW tubes ,31.8 x 1.2 mm thk(approx. 18 SWG) Round ERW tubes and 28.6 x 1.2 mm thk(approx. 18 SWG) Round ERW tubes(As per IS:7138) which are welded together.The Welded structures and cross connectors are coated with min. 45 micron thickness of epoxy polyester coating.Back supports which are provided at the rear back are made of 50.8 x 25.4 x 1.2 mm thk (approx. 18 SWG) rectangular ERW tubes(As per IS:7138).The tubes are coated with min. 45 micron thickness of epoxy polyester coating.The storage shelves are made from 0.6 mm thk MS sheet(As per IS:513) fixed below the radesk top panel and are coated with min. 45 micron thickness of epoxy polyester coating. Hooks are provided on the vertical side frames on both sides of the desk for hanging bags/bottles. They are made from 2 mm thk MS sheet(As per IS:513) and are coated with min. 45 micron thickness of epoxy polyester coating.The under structure is assembled using M6 trilobular screws(As per DIN 7500)with Zn blue plating.Compact Laminate seat and back panels are assembled using M6 Counter sunk Trilobular screws(as per DIN 7500) with Zn Black Plating (As per IS 1573:1986)Spacers Are provided on th top of round tubes for wooden panels fixing. They are made of made Glass filled (30%)Plastic Caps made of PP co polymer(3530 Grade) are also provided on the rear frames adding more aesthetic value to the product.M6 high tensile TVS make bolt(Class 8.8) with glass filled nylon level adjusters are provided at the bottom of under structure to take care of unevenness in floor with height adjustment of approx 15mm. Complete as directed by engineer incharge.(Make :- Godrej Interio, or equivalent (Make & System is as Per Selection of Consultant or Selection of Higher Authority) |
| 17 | Providing ,Supplying and fixing of Class Room 3 Seater Desk cum Bench For (Senior Class Room) Size (1840 x 1008D x 850H) As per below specification including erection at site Desk-Top Panel-All panels are made from 18mm thk Pte-laminated twin board (E1/P2 GRADE) with PVC edge banding on all sides.The panels have corners-rounded for safety usage. Desk-Top Panel-All panels are made from 18mm thk Pte-laminated Compact Laminated Board with Decorative Paper on both sides (AS PER IS 2046: 1995) The Panels have corners rounded for safety usage . Under structure - All side metal frames and cross connectors are made from combination of 25.4 x1.2 mm thk(approx. 18 SWG) Round ERW tubes ,31.8 x 1.2 mm thk(approx. 18 SWG) Round ERW tubes and 28.6 x 1.2 mm thk(approx. 18 SWG) Round ERW tubes(As per IS:7138) which are welded together.The Welded structures and cross connectors are coated with min. 45 micron thickness of epoxy polyester coating.Back supports which are provided at the rear back are made of 50.8 x 25.4 x 1.2 mm thk(approx. 18 SWG) rectangular ERW tubes(As per IS:7138).The tubes are coated with min. 45 micron thickness of epoxy polyester coating.The storage shelves are made from 0.6 mm thk MS sheet(As per IS:513) fixed below the radesk top panel and are coated with min. 45 micron thickness of epoxy polyester coating. Hooks are provided on the vertical side frames on both sides of the desk for hanging bags/bottles. They are made from 2 mm thk MS sheet(As per IS:513) and are coated with min. 45 micron thickness of epoxy polyester coating.The under structure is assembled using M6 trilobular screws(As per DIN 7500)with Zn blue plating.Compact Laminate seat and back panels are assembled using M6 Counter sunk Trilobular screws(as per DIN 7500) with Zn Black Plating (As per IS 1573:1986)Spacers Are provided on th top of round tubes for wooden panels fixing. They are made of made Glass filled (30%)Plastic Caps made of PP co polymer(3530 Grade) are also provided on the rear frames adding more aesthetic value to the product.M6 high tensile TVS make bolt(Class 8.8) with glass filled nylon level adjusters are provided at the bottom of under structure to take care of unevenness in floor with height adjustment of approx 15mm. Complete as directed by engineer incharge.(Make :- Godrej Interio, or equivalent (Make & System is as Per Selection of Consultant or Selection of Higher Authority) |
| 18 | Providing , supplying and Placing Free Standing Table (Faculty Table Class Room) 1200x600x728 ht) As per below specification including erection at site Enterprise 1200 Table without CPU Hanger size shall be 1200 Width mm x 600 Depth mm x 728 Height mm. Top shall be 18 mm thick Pre laminated particle board all work surface edges shall be having duly sealed with 2 mm thick PVC edge banding. Under structure Modesty Panel 18 mm thick Pre laminated particle board . The Rectangular frame shall be fabricated component in 1.2 mm thick CRCA , Finish : powder Coat( epoxy polyester) . Leg shall be fabricated component in 38 mm x 25 mm 1.2 mm thick MS ERW ATube ,finish powder coat ( epoxy polyester).The plastic cap for cable travel shall be injection molded polypropylene and leveler glide for shall be nylon 6 & MS bolt. The storage shall be having shell and drawer tray 0.6 mm thick CRCA Finish powder coat (epoxy polyester) plus the drawer front shall be 0.8 mm thick CRCA Finish powder coat (epoxy polyester) plus lock with 10 lever and handle and leveller. The wire management shall be horizontal wire carrier 0.7 mm thick CRCA Finish powder coat (epoxy polyester) and vertical wire carrier 0.8 mm thick CRCA Finish powder coat (epoxy polyester) .Complete as directed by engineer incharge.(Make :- Godrej Interio, or equivalent (Make & System is as Per Selection of Consultant or Selection of Higher Authority) |
| 19 | Providing, supplying and Placing of Chair (Faculty Class Rooms) As per below specification The seat is made up of 1.4 ± 0.1 cm thick hot - pressed plywood upholstered with fabric and molded polyurethane foam.SEAT SIZE: 48.0cm (W)x 51.0cm(D).The Back is injection molded in Glass filled Polypropylene which is upholstered with Mesh fabric.The back consist of fixed lumbar support made of injection molded Polypropylene having a nominal thickness of 0.4 ±0.02 cm.BACK SIZE: 44.0 cm(W) x 51.5 cm(H).The polyurethane foam for seat is of density = 30 ± 3 kg/m3.The armrest is made of injection molded Polypropylene which is connecting seat and back .The mechanism is designed with the Following features: 360° revolving type.,Centre - Tilt.,Tilt with upright lock.The pneumatic height adjustment has a stroke of 9.5 ± 0.5cm.The pedestal is injection molded Poly amide and fitted with 5 nos.twin wheel castors. The pedestal is 60.0 ±0.5 cm P.C.D.The twin wheel castors are injection molded in black Poly amide having 5.0± 0.1cm wheel Diameter (Make :- Godrej Interio, or equivalent (Make & Model as Per Selection of Consultant or Selection of Higher Authority) |
| 20 | Providing, supplying and Placing of Staff Room Chair (Administration) As per below specification Seat Assembly : The seat should be made up of 1.4 ± 0.1 cm thick hot - molded polyurethane foam and upholstered with fabric. Seat Size : 48.0cm (W)x 49.0cm(D). Back Assembly : The two part assembly upholstered with Mesh fabric should be made up of back outer injection molded in glass filled Poly amide and back inner injection molded in glass filled Polypropylene. The back consist of adjustable lumbar support having an adjustment of 4.0 ± 0.5cm. It should be made of injection molded Polyethylene (POM) which should be upholstered with foam and fabric . Back size: 47.0 cm(W) x 53.0 cm(H). Polyurethane Foam : The polyurethane foam for seat should be of density = 55 ± 5 kg/m3. 4. Two Way Adjustable Armrests : It should be made of glass filled Poly amide arm structure with PVC arm top having a height adjustment of 8.0 ±0.5cm. along with to-fro movements. Tilt Mechanism : The mechanism should be designed with the following features: 360° revolving type. • Tilt tension adjustment. • 3 position lock (including upright lock) giving option of variable tilt angle to the chair. Pneumatic Height Adjustment : The Class-3 pneumatic height adjustment has stroke of 10 ± 0.5cm. Pedestal Assembly : The pedestal should be injection molded in glass filled Poly amide and fitted with 5 nos. twin wheel castors.The pedestal should be 64.0 ±0.5 cm P.C.D. Twin Wheel Castors : The twin wheel castors are injection molded in Poly amide having 6.0± 0.1cm wheel Diameter.complete as directed by engineer incharge.(Make :- Godrej Interio, or equivalent (Make & Model as Per Selection of Consultant or Selection of Higher Authority) |
| 21 | Providing, supplying and Placing of Full Height Storage Cabinet (Principal Cabin) As per Bellow Specification Size 900mm x 350mm x 1200mm Storage having top made of 18mm thick MR grad plywood with balancing laminate in bottom of top, sides 18mm MR grad plywood with 1mm laminate finish. shutter made of 18mm thick plywood with laminate finish. shutter hanging on auto hinges with lock.Back 6mm thick MR grad plywood with bothside balacing laminated finish. complete as directed by engineer incharge.(Make :- Godrej Interio, or equivalent (Make & Model as Per Selection of Consultant or Selection of Higher Authority) |
| 22 | Providing ,Supplying and Placing of Storewel Cupboard (Plain Size 916mm x 486mm x1980mm) As per below specification. Storewell shall have an overall size of 916mm(W)x486mm(D)x1980mm(H) with welded construction. It should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. The Storwel Plain should have a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and shelving options shall be available. Complete as directed by engineer incharge.(Make :- Godrej Interio, or equivalent (Make & System is as Per Selection of Consultant or Selection of Higher Authority) |
| 23 | Providing ,Supplying and fixing of Soft Board (8 x 4 feet) as per below specification including erection at site. Woolen felt / Fabric in various colours. 9 mm thick soft board. Laminate sheet with extra melamine surface mix colour OR Galvanised steel sheet. Anodized 5 microns extruded Aluminium section designation 63400 as per IS:1285- 2002 - Width of Aluminium Frame = 16mm thickness +- 3 mm tolerance. (Make & Model is as Per Selection of Consultant or Selection of Higher Authority) |
| 24 | Providing ,Supplying and fixing of Green Writing Resin Magnatic White (8 x 4 feet) as per below specification including erection at site. Writing only. Resin Coated Sheet surface. 9 mm thick Particle board. Galvanised steel sheet, Anodized 5 microns extruded aluminium section designation 63400 as per IS:1285-2002 - Width of Aluminium Frame = 16 mm thickness +- 3 mm tolerance.(Make & Model is as Per Selection of Consultant or Selection of Higher Authority) |
| 25 | Providing ,Supplying and fixing of Notice board (3 x 2 feet) as per below specification including erection at site. Woolen felt / Fabric in various colours. 9 mm thick soft board. Laminate sheet with extra melamine surface mix colour OR Galvanised steel sheet. Anodized 5 microns extruded aluminium section designation 63400 as per IS:1285- 2002 - Width of Aluminium Frame = 16mm thickness +- 3 mm tolerance.(Make & Model is as Per Selection of Consultant or Selection of Higher Authority) |
| 26 | Providing ,Supplying and Placing of Stainless steel Open Top Round Dustbin (Size 10'' Dia x14''Ht 15 ltr Capacity) made from SS 200 preferred sheet 0.4mm thk (Tolerance +/- 0.2 mm) and resistance to corrosion, dustbins should be made from high-quality, durable materials that can with stand regular use and potential exposure to Garbage. (Colour : Silver , or as per Selection of Consultant or Selection of Higher Authority) |
| 27 | Providing ,Supplying Key Hanger Board for 30Keys Hanger Board Made fromgi steel material, it has 7 layered powder coated black finish, which is durable & long lasting.for Hanging Keys with openable able door with lock & keys The Size of this key storage box is – (l) 33 x (w) 5.5 x (h) 60.5 cm.Complete with installation as per direction of Engineer in charge. |
| 28 | Providing and Supplying & Fixing of Fire Extinguisher ABC 6 kg per floor 04 nos. (G+3) As complete as directed by engineer incharge. |
| 29 | Providing and Supplying & Fixing of CO2 (Fire Extinguisher) 9 Ltr in every lab (For Physics, Chemistry, Biology and Computer . complete as directed by engineer incharge. Please Enable Macros to View BoQ information |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
