|
| 1 | FOR GATE |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator) m/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil. |
| 3 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-lll) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 5 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge, for the following grades of concrete.: Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified mininum cement content, the contractor shall have discretion to either re design the mix or bear the cost of extra cement. All works upto plinth level Concrete of M25 grade with minimum cement content of 330 kg /cum |
| 6 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge, for the following grades of concrete.: Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified mininum cement content, the contractor shall have discretion to either re design the mix or bear the cost of extra cement. All works above plinth level upto floor V level Concrete of M25 grade with minimum cement content of 330 kg /cum |
| 7 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars |
| 8 | Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete |
| 9 | Centering and shuttering including strutting, propping etc. and removal of form for : Columns, Pillars, Piers, Abutments, Posts and Struts |
| 10 | Centering and shuttering including strutting, propping etc. and removal of form for : Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 11 | Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform. with water proof ply 12 mm thick |
| 12 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 13 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 14 | Providing and fixing dry cladding upto 10 metre height with 30 mm thick gang saw cut stone with machine cut edges of uniform colour and size upto 1mx1m, fixed to structural steel frame work and/ or with the help of cramps, pins etc. and sealing the joints with approved weather sealant as per Architectural drawing and direction of Engineer-in-charge. (The steel frame work, stainless steel cramps and pins etc. shall be paid for separately). |
| 15 | Providing and fixing stainless steel cramps of required size and shape for anchoring stone wall lining to the backing or securing adjacent stones in stone wall lining in cement mortar 1:2 (1 cement : 2 coarse sand), including making the necessary chases in stone and holes in walls wherever required. |
| 16 | Providing and fixing copper pins 7.5 cm long 6 mm diameter for securing adjacent stones in stone wall lining in cement mortar 1:2 (1 cement : 2 coarse sand), including making the necessary chases. |
| 17 | Providing, Making & Fixing of BOW/DHANUSH: Fabrication and installation of a Dhanush (Bow) measuring 13.30 meters in length, crafted in FRP with internal MS framework for structural support and long-term integrity. The process will begin with clay modelling by a skilled moulding artist to capture accurate form and detailing, followed by preparation of a die for casting FRP components. These FRP pieces will be obtained, aligned, and jointed seamlessly into a single integrated structure. The surface will then undergo sanding and finishing for precision, after which paint and a protective PU coating will be applied to achieve durability and aesthetic quality. The internal mild steel framework will be engineered to provide proper reinforcement, ensuring stability, strength, and safety of the installed bow structure complete in all aspects as per directions of Engineer-in-Charge. |
| 18 | Providing and fixing of 8 statues of rakshas: Fabrication and installation of 8 Rakshas statues, each 6 feet height, in FRP with internal MS framing for strength and durability. The process includes clay modelling by an artist, preparation of dies, casting and jointing of FRP pieces, followed by sanding, finishing, painting, and PU coating to ensure detailing, protection, and long-lasting aesthetics.complete in all aspects as per directions of Engineer-in-Charge |
| 19 | Providing, Making & Fixing 8 statues of Devtas: Fabrication and installation of 8 Devtas statues, each 6 feet height, in FRP with internal MS framing for strength and durability. The process includes clay modelling by an artist, preparation of dies, casting and jointing of FRP pieces, followed by sanding, finishing, painting, and PU coating to ensure detailing, protection, and long-lasting aesthetics. all aspects as per directions of Engineer-in-Charge. |
| 20 | Providing & Fixing of NAGRAJ VASUKI AS ROPE: Fabrication and installation of a giant Nagraj Vasuki, approx. 16 meters in length, crafted in FRP with an internal MS framework to ensure strength and long-term stability. The work will begin with detailed clay modelling by a skilled artist to capture the snake’s form, scales, and expressions, followed by the preparation of dies for casting. FRP components will then be obtained, aligned, and seamlessly jointed together to create the complete structure. The entire surface will undergo sanding and finishing to achieve precision in texture and detailing, after which paint and a protective PU coating will be applied to provide durability against weathering and enhance visual appeal. The concealed mild steel framing will be engineered to support the overall structure, ensuring safety, reinforcement, and proper installation of the giant Vasuki rope for the Samudra Manthan theme. complete in all aspects as per directions of Engineer-in-Charge. |
| 21 | Providing and fixing of MANDRACHAL PARVAT : Fabrication and installation of Mandrachal Parvat (Manthani) and Kachap (Tortoise) both of 4.8 meters height, crafted in FRP with an internal MS framework for reinforcement and long-term stability. The process will start with detailed clay modelling by a skilled artist to capture the mountain’s rocky contours and the tortoise’s natural features, followed by preparation of dies for casting. FRP pieces will then be cast, assembled, and jointed seamlessly into complete forms. The surfaces will undergo careful sanding and finishing to bring out textures and details, after which painting and PU coating will be applied to provide durability, protection from weathering, and aesthetic appeal. The internal MS framework will be engineered to support both structures effectively, ensuring safety, stability, and proper installation as integral elements of the Samudra Manthan theme.Mandrachal Parvat of height 10ft with diameter 8ft. complete in all aspects as per directions of Engineer-in-Charge |
| 22 | Providing and fixing of KACHAP PARVAT : Fabrication and installation of Mandrachal Parvat (Manthani) and Kachap (Tortoise) both of 4.8 meters height, crafted in FRP with an internal MS framework for reinforcement and long-term stability. The process will start with detailed clay modelling by a skilled artist to capture the mountain’s rocky contours and the tortoise’s natural features, followed by preparation of dies for casting. FRP pieces will then be cast, assembled, and jointed seamlessly into complete forms. The surfaces will undergo careful sanding and finishing to bring out textures and details, after which painting and PU coating will be applied to provide durability, protection from weathering, and aesthetic appeal. The internal MS framework will be engineered to support both structures effectively, ensuring safety, stability, and proper installation as integral elements of the Samudra Manthan theme.Kachap (Tortoise) of height 6ft and diameter 9ft. complete in all aspects as per directions of Engineer-in-Charge |
| 23 | Providing and fixing of DECORATIVE PILLAR: The FRP pillar of 2.40 meter made in FR (Fire Retardant) material with WR mat, will undergo a structured fabrication process. Initially, a clay model will be developed by a moulding artist to capture the precise detailing of the design. A mould will then be cast from this model, which will serve as the base for producing the FRP components. These components will be joined and reinforced, followed by surface preparation through sanding and finishing. The finishing sequence includes epoxy application to enhance bonding and durability, a base coat for uniform coverage, and a top coat for the desired finish. Finally, a PU (polyurethane) protective layer will be applied to safeguard the structure from external factors such as UV exposure, heat, dust, and debris, thereby ensuring long-term durability and aesthetic retention complete in all aspects as per directions of Engineer-in-Charge |
| 24 | Providing and fixing of ELEPHANT: Fabrication and installation of an Elephant structure of 2.10 meters height and 2.80 meters width, made in FR (Fire Retardant) material with WR mat finish and reinforced with an internal MS framework for structural strength. The process will begin with detailed clay modelling by a skilled moulding artist to capture realistic features and proportions, followed by preparation of moulds for casting FRP components. These components will then be cast, assembled, and joined seamlessly to form the complete elephant structure. The surface will undergo sanding and finishing, with epoxy applied to enhance bonding and durability. A base coat and top coat will be applied for uniform coverage and the desired appearance, followed by a PU protective layer to safeguard against UV rays, heat, dust, and debris. This ensures long-term structural integrity, weather resistance, and aesthetic retention complete in all aspects as per directions of Engineer-in-Charge |
| 25 | Providing and fixing of SHAMBHU JI: Fabrication and installation of a Shambhu Ji statue of 2.10 meters height and 2.63 meters width, made in FR (Fire Retardant) material with WR mat finish and reinforced with an internal MS framework for structural strength. The process will begin with detailed clay modelling by a skilled moulding artist to capture intricate features and proportions, followed by preparation of moulds for casting FRP components. The components will then be cast, assembled, and joined seamlessly to form the complete statue. The surface will be sanded and finished, with epoxy applied to enhance bonding and durability. A base coat and top coat will be applied for uniform coverage and the desired appearance, followed by a PU protective layer to protect against UV rays, heat, dust, and debris. This ensures long-term structural integrity, weather resistance, and aesthetic retention of the statue complete in all aspects as per directions of Engineer-in-Charge |
| 26 | Providing & Fixing of MOTIF DETAILS: Fabrication and installation of a Motif statue of 1.7 meters height and 1.6 meters width, made in FR (Fire Retardant) material with WR mat finish and reinforced with an internal MS framework for structural strength. The process will begin with detailed clay modelling by a skilled moulding artist to capture intricate features and proportions, followed by preparation of moulds for casting FRP components. The components will then be cast, assembled, and joined seamlessly to form the complete statue. The surface will be sanded and finished, with epoxy applied to enhance bonding and durability. A base coat and top coat will be applied for uniform coverage and the desired appearance, followed by a PU protective layer to protect against UV rays, heat, dust, and debris. This ensures long-term structural integrity, weather resistance, and aesthetic retention of the statue. complete in all aspects as per directions of Engineer-in- |
| 27 | Providing & Fixing of DOME: Fabrication and installation of a DOME statue of 3.580 meters height and 2.9 meters width, made in FR (Fire Retardant) material with WR mat finish and reinforced with an internal MS framework for structural strength. The process will begin with detailed clay modelling by a skilled moulding artist to capture intricate features and proportions, followed by preparation of moulds for casting FRP components. The components will then be cast, assembled, and joined seamlessly to form the complete statue. The surface will be sanded and finished, with epoxy applied to enhance bonding and durability. A base coat and top coat will be applied for uniform coverage and the desired appearance, followed by a PU protective layer to protect against UV rays, heat, dust, and debris. This ensures long-term structural integrity, weather resistance, and aesthetic retention of the statue. complete in all aspects as per directions of Engineer-in-Charge. |
| 28 | Providing and fixing of the platform for the Samudra Manthan statue is designed with a robust internal framework using MS (mild steel) square pipes, ensuring strong structural stability and long-lasting support for the statue. The exterior of the platform is finished with FR WR matte, providing a lightweight yet durable surface that can withstand weathering and environmental exposure. The FR surface can be further treated for a matte or gloss finish, enhancing the visual impact of the Samudra Manthan.Length of Platform – 13.30 mWidth of Platform – 3.040 mThickness of Platform – 39 cmcomplete in all aspects as per directions of Engineer-in-Charge |
| 29 | Providing and fixing of The platform for the Samudra Manthan statue is designed with a robust internal framework using MS (mild steel) square pipes, ensuring strong structural stability and long-lasting support for the statue. The exterior of the platform is finished with FR WR matte, providing a lightweight yet durable surface that can withstand weathering and environmental exposure. The FR surface can be further treated for a matte or gloss finish, enhancing the visual impact of the Samudra Manthan.Length of Platform – 12.19 mWidth of Platform – 3.040 mThickness of Platform – 29 cm including labour complete in all aspects as per directions of Engineer-in-Charge |
| 30 | LANDSCAPING |
| 31 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. |
| 32 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) |
| 33 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 34 | Stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately) :Sand stone - exposed face fine dressed with rough backing .50 mm thick |
| 35 | Providing and fixing stainless steel cramps of required size and shape for anchoring stone wall lining to the backing or securing adjacent stones in stone wall lining in cement mortar 1:2 (1 cement : 2 coarse sand), including making the necessary chases in stone and holes in walls wherever required. |
| 36 | Providing and fixing copper pins 7.5 cm long 6 mm diameter for securing adjacent stones in stone wall lining in cement mortar 1:2 (1 cement : 2 coarse sand), including making the necessary chases. |
| 37 | 12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand |
| 38 | Earth work in surface excavation not exceeding 30 cm in depth but exceeding1.5 m in width as well as 10 sqm on plan including disposal of excavated earth up to 50 m and lift up to 1.5 m, as per directions of Engineer in Incharge: All kinds of soil |
| 39 | Supplying and stacking of good earth at site including royalty and carriage upto 5 km lead complete (earth measured in stacks will be reduced by 20% for payment). |
| 40 | Supplying and stacking sludge at site including royalty and carriage upto 5 km lead complete (sludge measured in stacks will be reduced by 8% for payment). |
| 41 | Supplying and stacking at site dump manure from approved source,including carriage upto 5 km lead complete (manure measured in stacks will be reduced by 8% for payment) :Screened through sieve of I.S. designation 4.75 mm |
| 42 | Rough dressing the trenched ground including breaking clods |
| 43 | Uprooting weeds from the trenched area after 10 to 15 days of its flooding with water including disposal of uprooted vegetation. |
| 44 | Fine dressing of the ground. |
| 45 | Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately). |
| 46 | Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge |
| 47 | Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) : Holes 60 cm dia, and 60 cm deep |
| 48 | Providing and fixing M. S. tree guard 50 cm square in plan, height 1.40 metre above ground level and 0.50 metre below ground level. The vertical members shall consist of four nos of angle iron of size 25x25x5 mm 1.9 long, one at each corner and 8 nos flat iron of size 25x5 mm 1.4 long. The vertical members shall be welded to 4 nos 25x6 mm M. S. flats placed horizontally around the vertical member of the cage. One name plate of 1 mm thick M.S. sheet of size 250x100 mm shall be welded to the tree guard near the middle height and lettered CPWD / PWD/ any other approved name. The tree guard shall be fixed to the ground by making suitable holes and by embedding four corners leg in the ground, including refilling the earth, compaction etc. complete. The tree guard shall be painted with two coats of paint of approved brand and manufacture over a coat of primer, complete in all respect. |
| 49 | Filling mixture of earth and sludge or manure in the desired proportion in trenches, flooding with water and leveling (cost of supplying earth and sludge or manure and mixing excluded). |
| 50 | Excavation in bajri path including stacking of serviceable and unserviceable material separately, lead up to 50 m and lift up to 1.5 m, disposed material to be neatly dressed. |
| 51 | Flooding the ground with water including making kiaries and dismantling the same. |
| 52 | Complete maintenance of the entire garden features having as per yard stick in the garden area i.e. lawn trees, shrubs, herbs, edge, flower beds, foliages, creepers etc. including hoeing,weeding, pruning, replacement of plants, gap filling, watering, mowing of lawn, grass cutting by lawn mover and brush cutter, removal of garden waste, applying insecticide, pesticide & fertilizers(whenever required) top dressing of lawn with good earth and manure and maintenance of other garden related works as directed by office-in-charge (Cost of Good Earth, Manure, Fertilizer, Insecticide, Pesticide will be provided by the Department & lawn mover and brush cutter with fuel and other T & P material/articles shall be provided by the contractor.) and as per direction of officer in charge.Open spaces (1Mali for 3.00Acre). |
| 53 | Complete maintenance of trees (Out side garden features), jobs like making of basin at regular interval i/c watering, weeding, pruning & application of fertilizer etc, (excluding the cost of material which shall be supplied by the department and other T & P material/articles shall be provided by the contractor) and as per direction of officer in charge.Trees for 250 no/(up to 4 & up to 3 year Slow & Fast Per Plant/growing group) |
| 54 | Providing and wartering of irrigation water through water tanker of Horticulture features i.e. lawn, tree, shrubs, hedge/edge, ground cover etc. at the site of work. Water tanker having 5000 lit. capacity with one labour for watering i/c cost of water, filling of tanker, wartering at site with all leads and lifts as per direction of officer-in-charge. |
| 55 | Anti termite treatment of lawn area through premise 30.50% I P. one liter premise diluted in 499 liters water and applying solution @ 1.00 litre solution per sqm lawn or bed area.(two application) i/c cost of chemical)and as per direction of officer-in-charge.and as per direction of officer-in-charge. |
| 56 | Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water) Shrubs Plant |
| 57 | Clearing grass and removal of the rubbish up to a distance of 50 m outside the periphery of the area cleared. |
| 58 | Providing & laying Selection no. 1 grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with required tools wooden and than rolling the surface with light roller make the surface smoothen and light watering the same maintenance for 30 days or more till the grass establish properly,as per direction of officer in charge |
| 59 | Topiary cutting/shapping of plant removing of cut materials, cleaning, hoeing of plants complete design hoeing of trees (Topiary) watering manure etc.(excluding the cost of material which shall be supplied by the department) and as per direction of officer in charge.Height of Topiary above 120 cm |
| 60 | Providing and Displaying Ficus Retusa topiary well developed with fresh & healthy 5 to 6 big ball specific size and shape 180 to 210cm ht in 40 cm Cement Pot as per direction of the officer-in-charge. |
| 61 | Providing and Displaying Golden Bottle brush Topiary well developed with fresh & healthy foliage 5 to 6 big ball 115 to 180 cm ht in 40 cm Cement Pot as per direction of the officer-in-charge. |
| 62 | Providing and Displaying Topiary of Ficus Bush King well developed with fresh & healthy foliage from Top to Bottom with single piller 60 to 75 cmspread, 210 to 225 cm ht., in 35 cm Cement Tray/Cement Pot as per direction of the officer-in-charge. |
| 63 | Providing and Displaying Topiary of Ficus Panda well developed with fresh & healthy foliage with 3 to 4 Ball and 60 to 75 cm spread each Ball, 135 to 150 cm ht., in 35 cm Cement Tray /Cement Pot as per direction of the officer-in-charge |
| 64 | Providing and Displaying Topiary of Casuarina fresh & healthy having 5 to 6 specific shape and size ball well developed 195 to 210 cm ht. in 40 cm Cement Pot as per direction of the officer-in-charge. |
| 65 | Providing and displaying of Aglaonema Silver Queen having 30 cm to 45 cm. ht. with 12 to 15 leaves, multi suckers, fresh and healthy leaves, well developed in 25 cm dia Earthen pot/Plastic pot & as per direction of the officer-in-charge. |
| 66 | Providing and displaying of Aglaonema modestum having ht. 23 cm to 30 cm with 3 to 4 suckers & 15 to 20 leaves, well developed, fresh and healthy in 25 cm size of Earthen pot/Plastic pot. & as per direction of the officer-in-charge |
| 67 | Providing and displaying of Croton Challenger variety having ht. 30cm and above, well developed with full of fresh and healthy leaves in 20 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge. |
| 68 | Providing and Displaying Acalypha Different colour well developed, fresh & healthy with good foliage, multi branch 30 to 45 cm ht. in 20 cm size of Earthen Pot/ Plastic Pot bushy as per direction of the officer-in-charge. |
| 69 | Providing and Displaying Acalypha red well developed with fresh & healthy 30 to 45 cm ht. in 20 cm size Earthen Pot/ Plastic Pot as per direction of the officer-in-charge. |
| 70 | Electrical Work- |
| 71 | SITC of high quality long through mono color wash light, Protection Rating : IP66, complying to BIS standard \\"IS 10322 (Part 5/Sec 1): 2012\\" and having CE certification against standard \\"Low Voltage Directive & Protective Equipment - EN 60598-1:2015\\", and \\"Electromagnetic Compatibility Directive - EN 61547: 2009\\", Mounting Structure : Adjustable surface mount yoke arrangements for fixing the lights having the rotation degrees embosed in the die cast. Power consumption : 100W, CCT : 1800K/3000K/4000K/6000K, (as per the design approval), Optics : PMMA with holder, Beam Angle : 15º/25º/45º/60º, Control : ON/OFF, Body : Die casted / extruded aluminium with embossed manufacturer logo, Hot spot and light distribution : Optics Designed to minimize hot spots & fringing in different applications. Power Input : Constant DC 24V with external driver, Surge Protection : Inbuilt surge protection in the driver 2KV-4KV(Additional if required will be added as per the requirement), Toughened transparent glass having the IK protection up to IK08, Painting : Chemical 3/7 tank processed treatment before the powder coat black/ash/approved color coat. Fixture will be suitable to operate in a temperature range of 0°C to 50°C, The light fixtures are having IP68 air vent made of stainless steel which helps to desiccate & prevent from forming moisture inside the light fixture at worst environmental condition. LED life should be at least 50,000 burning hours at L70 at 35 degree centigrade. Luminaire is inclusive of Integral male/female waterproof connectors with structures in pre wired conditions as per IS standard. PCB thickness must be 1.6mm, 35 micron Copper, 2W TC with Black or White masking, Copper /OSP finish. LM79, IK07, IP66, NABL Acrediated laboratory. LED Makes should be CREE, LumilLED, Osram, Seoul, Nichia or equivalent with the engineer or 3rd party testing laboratory approval. Power Loop In/Out along with IP67 connector having the length >300mm. |
| 72 | SITC of high quality long through mono color Linear wash light, Protection Rating : IP66, complying to BIS standard \\"IS 10322 (Part 5/Sec 1): 2012\\" and having CE certification against standard \\"Low Voltage Directive & Protective Equipment - EN 60598-1:2015\\", and \\"Electromagnetic Compatibility Directive - EN 61547: 2009\\", Mounting Structure : Adjustable surface mount yoke arrangements for fixing the lights. Power consumption : 24W, CCT : 1800K/3000K/4000K/6000K, (as per the design approval), Optics : PMMA with holder, Beam Angle : 15º/25º/45º/60º, Control : ON/OFF, Body : Die casted / extruded aluminium with embossed manufacturer logo, Hot spot and light distribution : Optics Designed to minimize hot spots & fringing in different applications. Power Input : Constant DC 24V with external driver, Surge Protection : Inbuilt surge protection in the driver 2KV-4KV(Additional if required will be added as per the requirement), Toughened transparent glass having the IK protection up to IK07, Painting : Chemical 3/7 tank processed treatment before the powder coat black/ash/approved color coat. Fixture will be suitable to operate in a temperature range of 0°C to 50°C, The light fixtures are having IP68 air vent made of stainless steel which helps to desiccate & prevent from forming moisture inside the light fixture at worst environmental condition. LED life should be at least 50,000 burning hours at L70 at 35 degree centigrade. Luminaire is inclusive of Integral male/female waterproof connectors with structures in pre wired conditions as per IS standard. PCB thickness must be 1.6mm, 35 micron Copper, 2W TC with Black or White masking, Copper /OSP finish. LM79, IK07, IP66, HV Certificates from NABL Acrediated laboratory. LED Makes should be CREE, LumilLED, Osram, Seoul, Nichia or equivalent with the engineer or 3rd party testing laboratory approval. Power Loop In/Out along with IP67 connector having the length >300mm. |
| 73 | SITC of 17W Mono color Projector Spot light, Protection Rating : IP66, complying to BIS standard \\"IS 10322 (Part 5/Sec 1): 2012\\" and having CE certification against standard \\"Low Voltage Directive & Protective Equipment - EN 60598-1:2015\\", and \\"Electromagnetic Compatibility Directive - EN 61547: 2009\\", Mounting Structure : Adjustable wall mount yoke arrangements for fixing the lights. Power consumption : 17W, CCT : 1800/3000/4000/6000K, (as per the design approval) Optics : PMMA with holder, Beam Angle : 15º/25º/45º/60º, Control : ON/OFF, Body : Die casted / extruded aluminium with embossed manufacturer logo, Hot spot and light distribution : Optics Designed to minimize hot spots & fringing in color mixing applications. Power Input : DC 24V(External Driver) or AC 110-230V, 50Hz. Surge Protection : Inbuilt surge protection 2KV-4KV(Additional if required will be added as per the requirement), Glare : Specially designed glare free round shape 360 deg / 3 unit. Focussing area/LED will be kept 90 Deg perpendicular below the glare free optic. Size of the LED optic & glare unit must be equal or +/-2% higher to achieve the maximum intensity and less glare. This additional arrangement can be fixed or removed on the application. Glare free optical design for human viewing angle from a distance within 2-3 Mtr. Toughened transparent glass having the IK protection up to IK05 sealed above the glare free unit. Painting : Chemical 3/7 tank processed treatment before the powder coat black/ash/approved color coat. Fixture will be suitable to operate in a temperature range of 0°C to 50°C , LED life should be at least 50,000 burning hours at L70 at 25 degree centigrade. Luminaire is inclusive of Integral male/female waterproof connectors with structures in pre wired conditions as per IS standard. PCB thickness must be 1.6mm, 35 micron Copper, 2W TC with Black or White masking, Copper /OSP finish. LM79, IK05, IP66, HV Certificates from NABL Acrediated laboratory. LED Makes should be CREE, LumilLED, Osram, Seoul, Nichia or equivalent with the engineer or 3rd party testing laboratory approval. |
| 74 | SITC of high quality long through mono color wash light, Protection Rating : IP66, complying to BIS standard \\"IS 10322 (Part 5/Sec 1): 2012\\" and having CE certification against standard \\"Low Voltage Directive & Protective Equipment - EN 60598-1:2015\\", and \\"Electromagnetic Compatibility Directive - EN 61547: 2009\\", Mounting Structure : Adjustable surface mount yoke arrangements for fixing the lights having the rotation degrees embosed in the die cast. Power consumption : 50W, CCT : 1800K/3000K/4000K/6000K, (as per the design approval), Optics : PMMA with holder, Beam Angle : 15º/25º/45º/60º, Control : ON/OFF, Body : Die casted / extruded aluminium with embossed manufacturer logo, Hot spot and light distribution : Optics Designed to minimize hot spots & fringing in different applications. Power Input : Constant DC 24V with external driver, Surge Protection : Inbuilt surge protection in the driver 2KV-4KV(Additional if required will be added as per the requirement), Toughened transparent glass having the IK protection up to IK08, Painting : Chemical 3/7 tank processed treatment before the powder coat black/ash/approved color coat. Fixture will be suitable to operate in a temperature range of 0°C to 50°C, The light fixtures are having IP68 air vent made of stainless steel which helps to desiccate & prevent from forming moisture inside the light fixture at worst environmental condition. LED life should be at least 50,000 burning hours at L70 at 35 degree centigrade. Luminaire is inclusive of Integral male/female waterproof connectors with structures in pre wired conditions as per IS standard. PCB thickness must be 1.6mm, 35 micron Copper, 2W TC with Black or White masking, Copper /OSP finish. LM79, IK07, IP66, NABL Acrediated laboratory. LED Makes should be CREE, LumilLED, Osram, Seoul, Nichia or equivalent with the engineer or 3rd party testing laboratory approval. Power Loop In/Out along with IP67 connector having the length >300mm. |
| 75 | SITC of 9W Mono color Spot light, Protection Rating : IP66, complying to BIS standard \\"IS 10322 (Part 5/Sec 1): 2012\\" and having CE certification against standard \\"Low Voltage Directive & Protective Equipment - EN 60598-1:2015\\", and \\"Electromagnetic Compatibility Directive - EN 61547: 2009\\", Mounting Structure : Adjustable wall mount yoke arrangements for fixing the lights. Power consumption : 09W, CCT : 1800/3000/4000/6000K, (as per the design approval) Optics : PMMA with holder, Beam Angle : 15º/25º/45º/60º, Control : ON/OFF, Body : Die casted / extruded aluminium with embossed manufacturer logo, Hot spot and light distribution : Optics Designed to minimize hot spots & fringing in color mixing applications. Power Input : DC 24V with external driver, Surge Protection : Inbuilt surge protection 2KV-4KV(Additional if required will be added as per the requirement), Toughened transparent glass having the IK protection up to IK05, Painting : Chemical 3/7 tank processed treatment before the powder coat black/ash/approved color coat. Fixture will be suitable to operate in a temperature range of 0°C to 50°C, LED life should be at least 50,000 burning hours at L70 at 25 degree centigrade. Luminaire is inclusive of Integral male/female waterproof connectors with structures in pre wired conditions as per IS standard. PCB thickness must be 1.6mm, 35 micron Copper, 2W TC with Black or White masking, Copper /OSP finish. LM79, IK05, IP66, HV Certificates from NABL Acrediated laboratory. LED Makes should be CREE, LumilLED, Osram, Seoul, Nichia or equivalent with the engineer or 3rd party testing laboratory approval. |
| 76 | SITC of high quality Mono Color Neon Flexible light, Protection Rating : IP65, Mounting Structure : Adjustable wall mount SS clips for fixing the lights. Power consumption : 10W, CCT : 3000k, (as per the design approval) Beam Angle : 120º, Power Input : DC 24V with external driver, Surge Protection : Inbuilt surge protection 2KV-4KV(Additional if required will be added as per the requirement), Fixture will be suitable to operate in a temperature range of 0°C to 50°C , LED life time should be at least 50,000 burning hours at L70 at 25 degree centigrade. Luminaire is inclusive of Integral male/female waterproof connectors with structures in pre wired conditions as per IS standard. LED Makes should be CREE, LumilLED, Osram, Seoul, Epistar, Nichia or equivalent with the engineer or 3rd party testing laboratory approval. |
| 77 | SITC of Aluminium Profile for Neon flex MONO . |
| 78 | Supplying, Installation, Testing and Commissioning of water proof (IP 68) power supply unit of not less than 200W i/c connection along with 5 years free replacement guaranty etc. complete as required. |
| 79 | SITC of PVC insulated multi core electrical un armored flexible 5C x 0.5Sq mm power cable having less electrical losses. |
| 80 | Supplying and drawing following sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. 3 x 1.5 sq. mm |
| 81 | Supplying and drawing following sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. 3 x 2.5 sq. mm |
| 82 | SITC of Power Distribution Board made up of MS Sheet metal fabricated housing black powder coated and ivery connectors for the internal terminations and external outgoing connecting points, fibre / brass glands of suitable size fitted MCB control for outgoing circuits. Timer with required contactor for auto switching. Power panel suitable for indoor/outdoor applicable and floor mount / wall mount options.- 9 Nos of 6/10A SP Outgoing MCB's. - 1No of 16A TPN Incoming MCB. |
| 83 | SITC of IP driver box made up of PVC / UPVC for the internal terminations and external outgoing connecting points, with required PVC / brass glands, Optional suitable size MCB fitted for control outgoing circuits. |
| 84 | SITC of additional accessories for installing the lights as per the final drawing/site condition consisting of clamps, brackets, angles, conduits, joints, hardware's like fasteners, nut & bolts, PVC Conduit pipe, PVC Flexible pipe, HDPE Pipe, G.I Pipe, etc. as required and directed by Enginner-in-charge. |
| 85 | S/B of Copper bonded rod with Low carbon steel, high tensile strength copp bonded rod with copper coating. Diameter- 14 mm. Length- 3meter. Material- Copper Bonded, Coating thickness- 50 microns min., Environment friendly. RoHS Certified low resistivity Carbon based Ground Enhancement material in 24 Kg pack to fill the bore area around the rod & providing of suitable connector and lug including excavation and refilling as per specification with suitable size of hardpoly plastic earth pit chamber with locking arrangement . Accessories As per Site Conditions . Please Enable Macros to View BoQ information |
