|
| 1 | M&L for providing and fixing stainless steel (Grade 304) railing made of hollow tubes,channels, plates etc, including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc of required size on the top of floor or the side of waist slab by using driling with suitable arrangement complete all as specified & directed by the Engg-in-Charge. |
| 2 | Excavating in trenches n exc 1.5 m in depth for foundation or for laying of UG Cables, nexc 10 Sqm on plan and n exc 1.5 m in depth and getting out in hard/dense soil complete all as specified & directed by the Engg-in-Charge. |
| 3 | M&L for cement concrete 1:4:8 type D2 (using 40mm graded stone aggreagte) as in foundation filling, sub base and mass concrete or similar works complete all as specified & directed by the Engg-in-Charge. |
| 4 | M&L for Precast cement concrete Type C1 (1:3:6) (using 20mm graded crushed stone agg) block masonary with solid blocks exc 10cm in width and setting in CM 1:4 complete all as specified and directed by Engr-in charge. |
| 5 | M&L for Rendering 15mm thick on fair faces brick surfaces in cement mortar 1:4 finished even and smooth without using extra cement complete all as specified & directed by the Engg-in-Charge. |
| 6 | M&L for Preparing newly plastered surfaces and applying two coat of cement base paint over a coat of primer complete all as specified & directed by the Engg-in-Charge. |
| 7 | M&L for Providing precast cement concrete louvres and jallies Type B0 1:2:4 (12.5mm gradede aggregate), 25mm thick (measured solid) set in Cement mortar 1:4, including all mouldings, frame and reinforcement complete all as specified & directed by the Engg-in-Charge. |
| 8 | M&L for cement concrete (nominal mix) Type B0 1:2:4 (12.5mm gradede aggregate) as in roof kerbs or mud stops, Coping rounded or chamfered on edges complete all as specified & directed by the Engg-in-Charge. |
| 9 | Returning filling incl spreading leveling watering and well ramming in layers not exceeding 25 mm in any type of soil complete all as specified & directed by the Engg-in-Charge. |
| 10 | Removing excavated material not exc 50m and depositing where directed at a level n. exc. 1.50m above the starting point etc complete all as specified & directed by the Engg-in-Charge. |
| 11 | S&F Fe-290 (Gde E-165) Framed work as in ornamental door or gates of angle or other section with gusset plates rails, braces etc, complete, drilled for fixing of steel sheeting or other covering. Doors, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fiting (exclusive of steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing complete all as specified & directed by the Engg-in-Charge. |
| 12 | S&F 1.60mm thick MS plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched, including round headed screw, clouts nails or rivets and fixed to wood or steel framing with plain 40mm lap joints with riveted or welded seams, including bending or turnning up, mitred angle etc as required complete all as specified & directed by the Engg-in-Charge. |
| 13 | M&L for preparation of new or previously untreated steel surfaces of any description over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified & directed by the Engg-in-Charge. |
| 14 | M&L for Hard core of broken stones or boulders of gauge in exc 63mm deposited spread and levelled in layers n exc 15cm thick incl watering and rolled to true surface complete all as specified & directed by the Engg-in-Charge. |
| 15 | M&L for 75mm thick PCC (1:4:8) type D2 using 40mm graded aggregate as in sub base to floor or similar works complete all as specified & directed by the Engg-in-Charge. |
| 16 | M&L for 75mm thick PCC 1:3:6 type B1 (using 20 mm grade aggregate) as in plinth protection/paving or similar works complete all as specified & directed by the Engg-in-Charge. |
| 17 | M&L for providing MS Fe-290 (Gde E-165) for roof trussed (framed), trussed, purlins, crane gantries, rails and fastening and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specified & directed by the Engg-in-Charge. |
| 18 | M&L for providing MS Fe-410-W (GdeE-250) quality B Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated etc complete all as specified & directed by the Engg-in-Charge. |
| 19 | S&F Rolled mild steel Gde Fe-290 (Gde E-165) as in Plates (plain or chequered) channels,angle sections, square cut or notched (ordinary & counter sunk) forming holes, with riveted, bolted or welded attachment complete all as specified & directed by the Engg-in-Charge. |
| 20 | S&F 20mm dia of neck mild steel rag or lewis bolts, screwed one end, with hexagonal or square nuts and washers, the other end enlarged and jagged or lewised, length of bolt exc 30cm long complete all as specified & directed by the Engg-in-Charge. |
| 21 | S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified & directed by the Engg-in-Charge. |
| 22 | S&F Pre- painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified & directed by the Engg-in-Charge. |
| 23 | M&L for 25mm thick PCC type B0 1:2:4 (12.5mm graded aggregate) as in floor finished surfaces fair and even to receive tile or similar works complete all as specified & directed by the Engg-in-Charge. |
| 24 | M&L for Makaran dungri Marble 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade complete all as specified & directed by the Engg-in-Charge. |
| 25 | S&F second clas soft wood fillets square or rectangular in section sectional area exceeding 13sq cm and nexc 25sq cm as in scantling secured with nails or brads complete all as specified & directed by the Engg-in-Charge. |
| 26 | S&F 12mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with nails to timber frame work in walls complete all as specified & directed by the Engg-in-Charge. |
| 27 | S&F for suspended false ceiling system Powder coated Anodised aluminium snap grid frame work size 605x605 mm for false ceiling of the roof complete all as specified & directed by the Engg-in-Charge. |
| 28 | S&F Hangers 6mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40x3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long for suspended false grid of size 605x605mm complete all as specified and directed by the Engg-in-Charge. |
| 29 | S&F 12mm semi perforated calcium silicate tile of size 600x600 mm as in false ceiling complete all as specified and as directed by Engr-in-Charge. |
| 30 | S&F second class softwood moulding as in cornices, picture rails and the like sectional area exceeding 3Sqcm and nexc 6 sqcm fixed with nails complete all as specified and directed by the Engg-in-Charge. |
| 31 | S&F factory made uPVC door frame made of uPVC. extruded sections having an overall dimension (extruded section profile) 48x40 mm (tolerance ± 1 mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19x19mm and 1mm (± 0.1 mm) wall thickness complete all as specified by the manufacturer and as per directions of Engineer-in-charge |
| 32 | S&F factory made uPVC white colour casement (Openable) Door made of extruded profile wilh wall thickness of 2.3mm (+0.2mm). Window profile with hollow section with mitlti chamber, frame (60 x58mm), sash (60x78mm), T profile (One vertical length in between two shutters) (60x74mm), Glazing bead (35x20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc, making arrangement for fixing of hardware. EPDM gasket 1.2 + 0.2mm thick galvanized steel Frame (28x21.5mm), sash (31x27mm), T profile (27x17mm) to be inserted in required profile, frame will be fixed to the wall wilh 8x100mm long fasteners. Hardware: [casement door handle made of zinc alloyed (white powder coated). Corner striker. Secondary Strikers. Cylinder. Door transmission gear made of mild sleel with multi point locking system with strikes. 03 Nos 3D Hinges of zinc alloyed (white powder coated) for each shutter and 5mm thick glazing with selected quality glass complete all as specified and as directed by Engr-in-Charge.(Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose.) |
| 33 | S&F Steel rolling shutters of 1.25mm thickness of laths, without ball bearing including top cover, springs, anchoring rod, hasp and staple and one shop coat of primer, erected in position as indicated of gear operated type with bevel gear box and crank handle complete all as specified & directed by the Engg-in-Charge. |
| 34 | S&F Safety lever locks mild steel with 4 levers for rolling shutters complete all as specified & directed by the Engg-in-Charge. |
| 35 | S&F Ball bearing of any dia for rolling shutters complete all as specified & directed by the Engg-in-Charge. |
| 36 | M&L for sub main wiring with PVC insulated and PVC Round Sheathed 3-core Copper Conductor (flexible) industrial cable for Voltage Grade 1100 Volt, 1.5 sqmm in and including rigid PVC conduit of size 25 mm ISI mark and its accessories with fixing arrangements under piller, on wall, ceiling and trenches at a depth and width of min 150mm etc complete all as specified and directed by the Engg-in-Charge. Note : One run of 3-core Copper Conductor (flexible) industrial cable ,one run of PVC conduit together taken as one length for measuring unit length. Make of wire: Havells Cat part No. WHMFDSKG31X5 or equivalent in Finolex/Plaza. |
| 37 | S&F Gate light 7.5W LED Filament Lamp in aluminum die cast with modern artistic design and white PC diffuser suitable and including with LED lamp B22 type, suitable for pole dia 50 mm complete all as specified and directed by Engr-in-charge. Make: Havells Cat part no. LHFOASE1TZ5W009 or equivalent in Bajaj/Crompton/Surya |
| 38 | S&F Sheet metal enclosure DB's Double door SPN 240V, 4 way with 200 Amp rated bus bar including blanking plates where required complete all as specified and directed by Engr-in-charge. |
| 39 | S&F 240V 10 KA C curve MCB, SPN 32 Amp in the existing MCB DB complete with connection testing and commissioning complete all as specified and directed by Engr-in-charge. |
| 40 | S&F 240V 10 KA C curve MCB SP 5 to 32 Amp in the existing MCB DB complete with connection testing and commissioning complete all as specified and directed by Engr-in-charge. |
| 41 | Supply laying testing and commissioning of LT UG cable 2 core 10sq mm 1100 Volts grade XLPE insulated , armored, heavy duty with aluminium conductor laid in trenches or fixed to walls/ poles or passing through pipes with and including, cable gland lugs/ thimbles/ ferrules complete all as specified and directed by Engr-in-charge. Notes: Excavation,RFR and protection pipe etc. Shall be measured and paid separately under relevant item of schedule |
| 42 | S&F double wall corrugated HDPE (DWC) pipe of size OD 50/38 mm, laid in trenches for protection of cable complete all as specified and directed by Engr-in-charge. |
| 43 | S&F GI tubing Medium grade 50mm bore for fixing of light on piller and under trenches complete all as specified and directed by Engr-in-charge. |
| 44 | M&L for Earthing complete with galvanised steel earth plate electrode of size 60x60x6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to and including GI iron wire of size 4 mm dia by means of GI bolts, nuts, check nuts and washers, protected by 15mm bore GI light grade ISI marked pipe upto and including test points. Earth plate shall be surrounded by alternate layer 15cm thick of charcoal or coke and common salt all around bottom and top , 20cm bore GI medium grade ISI marked pipe for watering and including funnel,wire mesh,PCC chamber pit made with PCC(1:3:6) type C-1(using 20mm graded stone aggregate) including necessary form work, excavation and earth work in any type of soil, returning filling and disposal of surplus soil to a distance not exceeding 50M, CI pit cover duly painted with two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified & shown in electrical plate No.3 of SSR 2009(Part-I) and all as directed.Note:- (i) Protection pipe and earthing strip upto test point from top of the earth plate and further upto the body of electrical equipment shall be included in the unit rate of this item.(ii) Earth testing arrangement should be done by contractor as per direction of Engr-In-Charge. |
| 45 | M&L for Point wiring for light/fan/bell with FRLS cable of 1.5sqmm PVC insulated (red/blue/yellow for phase, black for neutral and green for earth) unsheathed multistranded copper conductor 1100 volts grade in and including not less than 2mm thick PVC casing caping with all accessories and 1.5sqmm green in colour PVC insulated multistranded copper conductor FRLS cable for earth continuity connected to common earth dolly incl MS/GI sunken box with 3mm thick pre laminated hylum sheet/PVC box with back plate,flush/surface type for mounting fittings such as switches,socket,and regulator complete all as specified and directed for one light point or bell/buzzer point controlled by one switch. |
| 46 | All as per Srl item No.45 here in before but using cable size 2.5 Sqmm for one 3 pin socket outlet 5 Amps independent board. |
| 47 | All as per Srl item No 45 here in before but using cable size 2.5 Sqmm for one 3 pin socket outlet 15 Amps independent board. |
| 48 | S&F Switch piano flush type 5 Amps, single pole one way complete all as specified and directed by Engr-in-charge. |
| 49 | S&F Switch socket combination 2 in 1, and 3 and 2 pin, 5 Amps flush type complete all as specified and directed by Engr-in-charge. |
| 50 | S&F Switch socket combination 2 in 1, 3 pin, 5 and 15 Amps flush type complete all as specified and directed by Engr-in-charge. |
| 51 | S&F Ceiling rose on PVC Square Block surface bakelite 65x50mm, two to three terminals complete all as specified and directed by Engr-in-charge. |
| 52 | S&F LED white colour 1x18 Watt, 220 V, AC, Decorative ultra slim square profile LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient ready to use, connecting up with two/three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed by Engr-in-charge. |
| 53 | S&F LED luminarie 600x600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete 6000K with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed by Engr-in-charge. |
| 54 | S&F LED streek track light 12 watt 4000 K, Natural white , Surface colour- Black, IP>66, Black powder coated die cast aluminium housing with in built energy efficent surge protected electronic driver, with all connected accessories complete all as specified and directed by Engr-in-charge.Make :Havells Cat part no. LHEEANPBPH1K012 or equivalent. |
| 55 | S&F UNO Track Light accessories (Track) of length 1 Mtr for streek track light, Track Surface colour- Black, powder coated die cast aluminium housing, with all connected accessories complete all as specified and directed by Engr-in-charge.Make :Havells Cat part no. 1MTR1PHASE TRACK TSBLK or equivalent in approved make. |
| 56 | S&F Sheet metal enclosure for DB's Double door, SPN 240V, 8 way with 200 Amp rated bus bar including blanking plates where required complete all as specified and directed by Engr-in-charge. |
| 57 | S&F 240V, 10 KA C curve MCB, SPN 40 to 63Amp in the MCB DB complete with connection testing and commissioning complete all as specified and directed by Engr-in-charge. |
| 58 | S&F 1100 volts grade heavy duty 16 sqmm 2 core flat cable PVC insulated aluminium stranded conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections complete all as specified and directed by Engr-in-charge. |
| 59 | Note : Deduction for amount of Rs. 0.00 as listed in Schedule 'A' Part-II (Schedule of Credit) shall be made while awarding of contract. Please Enable Macros to View BoQ information |
