|
| 1 | Scarifying or picking gravelled, macadam or bituminous macadam surfaces in area not exceeding 400 Sqm and depth exceeding 50 mm but not exceeding 100 mm deep including removing stacking and deposing off, complete all as specified and directed. |
| 2 | Repair to potholes any depth, not exc 1.00 sqm each including sweeping free from dust and mud, or water, scoring sunken surfaces in roads, paths, etc. cutting around edges to at least 25 mm in depth, making good by filling in screened & graded road metal, watering and well ramming (including supply of road metal), complete all as specified and directed. |
| 3 | M&L for repairs to potholes of any depth not exceeding 1.0 sqm each including sweeping free from dust & mud or water, scoring sunken surfaces in road, path etc, cutting around edge to at least 25 mm in depth, making good by applying tack coat with cationic emulsion @5 kg per 10 sq m, putting in premixed bituminous, well rammed and sealed with binder 9.8 kg per 10 sq m, blinded with 0.09 cu m of stone chippings, 6.3 mm size and again well rammed (including supply of premixed macadam, binder and chippings) depth of potholes exc 30 mm complete all as specified and directed. |
| 4 | M&L for 150 mm thick water bound macadam in two equal layers of 75 mm each (compacted thickness) with coarse aggregate of stone (Granite, trap or Basalt) of grading - 2 ( 63 mm to 40 mm size ) or of grading - 3 ( 50 to 20 mm size ) and consolidated to required gradient & camber with 8 to 10 tonne power roller, complete all as per specified and as directed. |
| 5 | M&L for preparing un-surfaced water bound macadam by brushing with wire brushes for removing caked etc sweeping with brooms and finally fanning the cleaned surface with gunny bags to remove all loose dirt etc, complete all as specified and directed. |
| 6 | M&L for premix bituminous, macadam laid/rolled and compacted to required gradient and camber (consolidated thickness 75mm or less) using paving bitumen Vg-30 @ 4% (minimum) by the weight of total mix of any penetration compacted to required gradient and camber with 8 to 12 tone power roller, complete all as specified and directed.NOTE : (i) No extra allowances shall be admissible to the contractor if the bitumen content is required more than 4% by the weight of total mix as per approved design. The contractor shall quote the rate accordingly. |
| 7 | M&L for applying enenly a tack coat of cationic bitumen emulsion (RS-1) conforming to IS : 8887 at a rate of application of .35 kg/sqm on bituminous surface as specified in table 500-5 of Morth specification for road and bridge work 2013, using mechanical spraye, complete all as specified and directed by Engineer-in-charge |
| 8 | M&L for applying evenly a tack coat of cationic bitumen emulsion (RS-1) conforming to IS : 8887 at a rate of application of 0.20 - 0.30 kg/sqm on bituminous surface as specified in table 500-5 of Morth specification for road and bridge work 2013, using mechanical sprayer after cleaning of existing surface by air compressor to remove all loose dirt etc., complete all as specified and directed by Engineer-in-charge |
| 9 | M&L for bituminous premix asphaltic semi dense concrete 40mm consolidated thickness (minimum) with 5.5% binder content of paving bitumen Gde-VG-30 by weight of total mix, rolled and compacted, mixed in mechanical hot mixed plant and pre-mixed material laid with mechanical paver, finished including rolling to required gradient and camber with 8 to 12 tonne power roller to required compaction complete all as specified in the relevant clauses of SSR Part-I (2009) and, complete all as specified and directed.Note : (a) Rate deemed to be included for making good of any undulation/damages in wearing surfaces, where semi sense asphaltic concrete to be laid. (b) Semi dense asphaltic bituminous concrete shall be designed as specified and binder content shall be provided as per design mix, contractor shall quoted his rates considering the bitumen contents as 5.5%. Any variation in binder content on minus side shall be adjusted at the rate of Rs 50.00 per kilogram of binder but variation in binder plus side shall not be paid extra contractor shall quote accordingly. |
| 10 | M & L for preparing bituminous surfaces of road and marking 2.5mm thick centre lines, stop lines, dashes, arrows etc. and the like n. exc 10cm wide on roads pavements with hot applied thermo plastic road marking paint of approved colour confirming to BS 3262-1989 with special applicator machine all as per manufacturers instruction and complete all as specified and directed. |
| 11 | Supply and fixinging of metal tubular dealineator made out of ABS round body fitted with 2 Nos 65 mm dia highly reflective reflectors made out of PMMA and mounted on 45/50 mm dia mild steel pipe of 600 mm height duly powder coated and thermoplastic elastomer 3 bands of green, red and yellow reflector radium tape of 25 mm wide strips with anti theft steel net for reflector protection including embedding in PCC 1:2:4 (150x150x300mm) type B1, complete all as specified and as directed. |
| 12 | Supply and fixing in repair of cat eye solar reflective type of metal body alloy of size 100mm x 100mm x 20mm with PAMA striplens reflector of model No. DA 972.0 fixed with and incl MS stud of suitable size as per manufactures instructions and complete all as specified and directed. |
| 13 | Supply and fix in repair of solar cat eye aluminum alloy shall (100% water proofing design according to 65) of size 125mm x 125mm x 25mm (shank 65mm) of high efficiency Mono rystafie solar panel 2.4V/ 0.3 watt one NI-ed rechargeable battery (1.2V/ 1600MA) consisting of super bright LED with 10,000 to 18,000 mcd completed as per manufactures instructions and complete all as specified and directed.Note - The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender, from total amount of Schedule 'A'/BOQ. Please Enable Macros to View BoQ information |
