|
| 1 | Repairs to existing aluminium doors by making adjustments in members to make them smooth functionable including necessary opening of parts, grinding, cutting, fixing of cleats, hinges, rubber beads, rollers, screws, adjustment of door closer etc. complete all as directed by Engineer-in-Charge. |
| 2 | Repairs to existing aluminium windows by making adjustments in members to make them smooth functionable including necessary opening of parts, grinding, cutting, fixing of cleats, hinges, rubber beads, rollers, screws etc. complete all as directed by Engineer-in-Charge |
| 3 | Material & labour fixing door chowkhats in existing opening including embedding chowkhats in floors or walls cutting masonry for holdfasts, embedding hold fasts in cement concrete blocks of size 15 x 10 x 10 cm with cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size), painting two coats of approved wood preservative to sides of chowkhats and making good the damages to walls and floors as required complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge. |
| 4 | Material & labour fixing window chowkhats in existing opening including embedding chowkhats in floors or walls cutting masonry for holdfasts, embedding hold fasts in cement concrete blocks of size 15 x 10 x 10 cm with cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size), painting two coats of approved wood preservative to sides of chowkhats and making good the damages to walls and floors as required complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge. |
| 5 | Taking down cement plaster on wall / ceiling surfaces including racking out joints, hacking for key scrubbing down with water etc to receive new plaster all as specified and directed by the Engineer-in-Charge. |
| 6 | Material and labour for rendering 12 mm thick on fair faces of brick work or concrete wall surfaces in CM 1:6 finished even and smooth without using extra cement complete all as specified and directed by the Engineer-in-Charge. |
| 7 | Material and labour for distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour with two coats on new work complete, as per manufacturer's specification over including 2mm thick internal wall care putty finish complete all as specified and directed by Engr-in-charge. |
| 8 | Supply and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. (Fixed to steel windows by welding) including priming coat with approved steel primer complete all as specified and directed. |
| 9 | Material and labour for preparation of old surfaces of steel/wooden surface and Painting with two coats of synthetic enamel paint of approved brand and manufacture of required colour to give an even shade complete all as specified and directed by Engr-in-charge. |
| 10 | Material and labour for two coats incl preparation of steel/wooden surface and Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade complete all as specified and directed by Engr-in-charge. |
| 11 | Taking out doors, windows and clerestory window shutters (steel or wood) of area 3 sq. metres and below including stacking within 50 metres lead complete all as specified and directed. |
| 12 | Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge. |
| 13 | Material and labour for Supply 2nd class teakwood work in frames of doors,windows,clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). |
| 14 | Material and labour for Supply 35mm thick ISI marked flush door shutters conforming to IS :2202(Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains on cross band and face veneer on both face of shutter including ISI marked butt hinges and necessary screws as per specified and directed by Eng-in-Charge. |
| 15 | Supply and fixing factory made uPVC glazed/wire mesh three tracks three panels sliding window with Aluminium channels for roller track, wool pile, nylon rollers with SS 304 body. Using R3 series with frame (98 mm & above)*(40 mm &above) & both glazed and fly screen sash (30mm & above)*(55mm & above) with zinc alloy (zamak) powder coated handle on every glazed panels along with multi point locking system(height upto 1.8m) comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler(wherever required) extruded profiles having minimum wall thickness of 2.1mm for series R3 and R4 profiles conforming to EN:12608 in any shape, colour and design duly reinforced with galvanised mild steel section made of required shape & size. uPVC extruded glazing beads, interlock and inline sash adaptor (wherever required) of appropriate dimension, hardware,SS304 grade fasteners of minimum 8mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS1367: Part 1 to 14, plastic packers plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality , all complete as per direction of Engineer-in-charge. Section of steel reinforcement and cross sections of uPVC profile to be as per design approved by Engineer-in-charge. wiremesh/ Glazing of plain/ toughened/ double glass unit with/ without high performance coating as per design requirements and conforming to IS: 3548 & IS:16231 shall be paid separately complete all as specified and directed. |
| 16 | Supply and fixing factory made uPVC Two track two panels sliding window with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body. Using R2 series with frame (40mm & above) x (40mm & above) & sash(25mm&above) x (50 mm & above) with zinc alloy (zamak) powder coated touch locks with hook(Height upto 1.2 metre). comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler(wherever required) extruded profiles having minimum wall thickness of 1.7mm for series R1 and R2 profiles conforming to EN:12608 in any shape, colour and design duly reinforced with galvanised mild steel section made of required shape & size. uPVC extruded glazing beads, interlock and inline sash adaptor (wherever required) of appropriate dimension, hardware, SS 304 grade fasteners of minimum 8mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS1367: Part 1 to 14, plastic packers plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality , all complete as per direction of Engineer-in-charge. Section of steel reinforcement and cross sections of uPVC profile to be as per design approved by Engineer-in-charge. wiremesh/ Glazing of plain/ toughened/ double glass unit with/ without high performance coating as per design requirements and conforming to IS: 3548 & IS:16231 shall be paid separately complete all as specified and directed. |
| 17 | Supply and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm With 12 mm mild steel U beading complete all as specified and directed. |
| 18 | Supply and fixing aluminium work for fixed portion of doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections Powder coated aluminium (minimum thickness of powder coating 50 micron) and other sections of approved make conforming to IS: 733 and IS: 1285, fixing frames with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P.brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing to be paid for separately) complete all as specified and directed. |
| 19 | Supply and fixing aluminium work for shutters of doors, windows & ventilators of powder coated aluminium (minimum thickness of powder coating 50 micron) including Supply and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required with extruded built up standard tubular sections/ appropriate Z sections Powder coated aluminium (minimum thickness of powder coating 50 micron) and other sections of approved make conforming to IS: 733 and IS: 1285, fixing frames with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P.brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing be paid for separately) complete all as specified and directed. |
| 20 | Supply and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS:12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. with pre-laminated particle board with decorative lamination on both sides complete as per architectural drawings and directions of Engineer in-charge |
| 21 | Supply and fixing glazing with float glass panes of 5 to 4.5mm thickness (weight not less than 12.50 kg/sqm) in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge complete all as specified and directed. |
| 22 | Supply and fixing frosted glass panes 4mm thick (weight not less than 10kg per sqm) indoors, aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc .(Area of opening for glass panes excluding portion inside rebate shall be measured) complete all as specified and directed. |
| 23 | Supply and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc complete all as specified and directed. |
| 24 | Supply and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36kg to 80kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete all as specified and directed. |
| 25 | Supply and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing with brass pivot and single piece M.S. sheet outer box with slide plate etc With stainless steel cover plate minimum 1.25 mm thickness complete as per the direction of Engineer-in-charge. |
| 26 | Supply and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineer-in-Charge. |
| 27 | Supply and fixing factory made panel PVC door shutter 30mm thick consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer's specification & drawing. |
| 28 | Supply and fixing 200x10mm aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete all as specified and directed. |
| 29 | Supply and fixing 150x10mm aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete all as specified and directed. |
| 30 | Supply and fixing bright /matt finished Stainless Steel 125mm handles of approved quality & make with necessary screws etc complete all as specified and directed. |
| 31 | Supply and fixing 125mm aluminium handles, IS marked, anodised (anodic coating not less than grad AC10 as per IS:1868) transparent or dyed to required colour or shade, with necessary screws etc.complete as per specified and directed by Eng-in-Charge. |
| 32 | Supply and fixing 100mm aluminium handles, IS marked, anodised (anodic coating not less than grad AC10 as per IS:1868) transparent or dyed to required colour or shade, with necessary screws etc.complete as per specified and directed by Eng-in-Charge. |
| 33 | Supply and fixing IS:12817 marked stainless steel butt hinges (Size 100 x 58 x 1.90 mm) with stainless steel screws etc. complete all as specified and directed. |
| 34 | Supply and fixing 300x16mm aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete all as specified and directed |
| 35 | Supply and fixing aluminium Twin rubber stopper hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete all as specified and directed. |
| 36 | Hacking out old broken glasses any thickness size, quality, description from metal frame including punching or drilling out old glazing pins /spring clips etc all as specified and directed by Engineer-in-Charge. |
| 37 | M&L for renewing glass panes, with putty and nails wherever necessary including racking out the old putty: float glass panes of nominal thickness 4mm (weight not less than 10kg/Sqm) as specified and directed by Eng-in-charge. |
| 38 | M&L for Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: float glass panes of nominal thickness 5mm (weight not less than 12.5kg/Sqm) as specified and directed by Eng-in-charge. |
| 39 | M&L for two coat of French polishing to existing wooden surfaces including preparation of surfaces complete all as specified and directed by Engr-in-charge. |
| 40 | Supply and laying cement concrete in retaining walls, return walls, walls(any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., upto floor five level, excluding the cost of centering, shuttering and finishing: 1:2:4 (1Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) as specified and directed by eng-in-Charge. |
| 41 | S&F in repairs Venetian blinds of approved make vertical type using 100mm wide fabric blinds of approved colour/ shade and pattern including operating arrangement such as chord/ thread, counter weight, connecting chain etc and necessary fittings complete, all as specified and directed. |
| 42 | Supply and fixing plywood 4mm thick, one side decorative veneer conforming to IS: 1328 (type-1), for plain lining/ cladding with necessary screws, including priming coat on unexposed surface with decorative veneer facings of approved manufacture as specified and directed by Eng-in-Charge. |
| 43 | Supply and fixing nickel plated M.S.pipe curtain rods with nickel plated brackets 20mm dia (heavy type) complete all as specified and directed by Eng-in-Charge. Please Enable Macros to View BoQ information |
