Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Taking down chowkhats or frames with shutters n.exc 1.5 sqm each(without taking off shutters from the frame) and removing from site all as directed. |
| 2 | Taking down chowkhats or frames with shutters but exc 1.5 sqm but n.exc 4sqm each complete all as specified and directed . |
| 3 | Taking down shutters exc 1sqm but not exc 2 sqm each and removing from site all as directed. |
| 4 | S&F Framed work such as grills, gratings, chowkhats of angle/channel section etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walkways; railings; gates, framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete, all as specified and directed |
| 5 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm thick size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.(Note: stainless steel butt hinges and necessary S S screws shall be paid separately) complete all as specified. |
| 6 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65x125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. complete.all as specified and directed. |
| 7 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. complete.all as specified and directed. |
| 8 | S&F 100 mm size butt hinges, medium weight , cold rolled, mild steel and fixed complete all as specified and directed |
| 9 | S&F Stainless steel barrel tower bolt 125mm long extruded section all as specified. |
| 10 | S&F 150mm size Stainless steel handles fabricated type anodised complete all as specified. |
| 11 | S&F 300mm long aluminium alloy anodised sliding bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts and extruded section or cast aluminium alloy and fixed complete. |
| 12 | Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) or openable type/casement windows upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead/double glazing bead of appropriate dimension comprising of uPVC multi chambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 13 | Supply and fixing factory made uPVC white colour Casement door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.50 sqm) comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality complete all as specified and directed by Engineer-inCharge. (Glass shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 14 | Supply and fixing factory made uPVC white colour Two track two panels sliding glazed window upto 1.50m height made of (small series) frame 52 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of window upto 1.75 sqm) comprising of uPVC multi-chambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall beacceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 15 | Supply and fixing factory made uPVC white colour fixed glazed window/ ventilator/ partition made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Glass shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 16 | Supply and fixing factory made uPVC white colour casement (Openable) window made of extruded profiles with wall thickness of 2.3mm ( + – 0.2mm) Window profile with hollow section with multi chamber, frame (60mm x 58mm), sash (60mm x 73mm), T profile (One vertical length in between two shutters) (60mm x 74mm), Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware EPDM gasket 1.2 +– 0.2mm thick, galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27.5mm). T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100mm long fasteners. Hardware: [casement handle made of zinc alloyed (white powder coated), But Hinges of'zinc alloyed (white powder coated), transmission gear made of mild steel with multi point locking system] and 5mm thick glazing with selected quality glass and stainless steel wiremesh. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose.) Area exceeding 1.00 sqm but not exceeding 2.00 sqm each. |
| 17 | S&F for 20 to 25 mm dia stainless steel drapery curtain rod with brass /nickel chrom polish / designer lattos and brackets complete all as specified and approved by Engr-in-Charge including taking out old pelmet with curtain rods all as directed.directed . |
| 18 | S&F Stainless steel wire cloth, 0.56mm nominal dia of wire & average width of aperture 1.18mm with stainless steel wire staples complete all as specified and directed . |
| 19 | S&F 4.8mm thick ordinary sheet glass and glazing with oil putty complete in squares not exc 0.50 Sqm each pane complete all as specified and as directed. |
| 20 | S&F 4.8mm mm thick ordinary sheet glass and glazing with oil putty complete in squares exc 0.50 Sqm each pane complete all as specified and as directed. |
| 21 | Demolition of brick work built in cement mortar incl all quoins, arches, pillars etc complete all as specified and as directed. |
| 22 | M&L for brick work with sub class 'B' bricks old size bricks strainght or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and as directed. |
| 23 | M&L for 1/2 brick work with sub class 'B' bricks , using old size bricks, straight or curved on plan exc 6 m mean radius built in cement mortar 1:4 complete all as specified and directed. |
| 24 | Taking down cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified. |
| 25 | M&L for Rendering 15mm thick (1:6) on fair faces of brick work or concrete surfaces mixed with water proofing for Internal Wall finished even and fair without using extra cement complete all as specified and directed. |
| 26 | M&L for Rendering 15mm thick (1:4) on fair faces of brick work or concrete surfaces mixed with waterproofing compound External Wall finished even and fair without using extra cement complete all as specified and directed.(Note : WPC Shall measured and paid separately) |
| 27 | M&L for rendering 5mm thick (1:3) plaster on ceiling concrete surface in cement mortar, finished even and fair without using extra cement complete all as specified and directed. |
| 28 | M&L preparation of new surface of wall and applying 2-3 mm thick JK/BIRLA white wall care putty and applying two coats of plastic emulsion paint over a coat of oil based primer complete all as specified and directed |
| 29 | M&L for preparation of newly plastered surfaces of any description and applying two coats of cement base paint all as specified and directed. |
| 30 | M&L for preparation of newly plastered surfaces and applying two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm over new surfaces all as specified and directed. |
| 31 | M&L for preparation of new plastered of ceiling and applying three coats of white wash as in ceiling complete all as specified and directed. |
| 32 | M&L for complete removal of existing treatment by mechanical/manual means and applying one coat of 3mm thick wall care putty (Birla white or equivalent) in two layers and applying two coats of oil bound distemper over a after preparation of on old wall surfaces complete all as specified and directed. |
| 33 | M&L for preparation of old plastered or unplastered surfaces of ceiling and applying two coat of white wash as in ceiling complete all as specified and directed. |
| 34 | M/L for preparation of old plastered surfaces of wall of any description and applying two coats of cement base paint all as specified and directed. |
| 35 | M&L for applying two coats of cement base paint, white or tinted on new wall surface including preparation of surface complete as |
| 36 | M & L for preparing new plastered surfaces of wall and applying two coats of distemper oil emulsion over a coat of alkali resistant cement primer and over a coat of 2 to 3mm thick wall care putty complete all as specified and directed. |
| 37 | Material and Labour for apply two coats of Anti fungal weather coat acrylic emulsion paint over a coat of primer on new surfaces including 2 -3 mm thick wall putty, complete all as specified and directed. Make of Arcylic emulsion weather coat paint :- Asian (Apex Ultima) ,Berger (Super coat ) or ICI Dulux (weather shield) .Make of primer :- Asian (X2) or Equivalent . Note:- (a) Each stage i.e. preparation of surfaces, application of primer, application of first coat, application of second coat will be got passed from Engr-in -Charge.(b)Written Warranty for four years or as per manufacturer's instructions, whichever is more is required to be furnished by contractor for this item. |
| 38 | M & L for preparing new plastered surface on ceiling and applying two coat of oil bound distemper complete all as specified and directed. |
| 39 | M&L for preparation of old decorated plastered or unplastered surface including complete removal by brooming down with steel wire brushing, scraping down smoke soot, moulded, moss, efflorscent salt, trading oil and greasy spots and applying two coat of Oil bound distemper on walls over 2mm thick plaster of paris putty as specified and directed by Engr-in-Charge. |
| 40 | M&L for preparation of old decorated plastered or unplastered surface including complete removal by brooming down with steel wire brushing, scraping down smoke soot, moulded, moss, efflorscent salt, trading oil and greasy spots and Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) on walls over 2mm thick plaster of paris putty as specified and directed by Engr-in-Charge. |
| 41 | M&L for old ceiling surfaces two coat of oil bound distemper on old surface on ceiling including complete removal preparation of old surface complete all as specified and directed. |
| 42 | Dismantling of floor, hearth or wall tiling with cement mortar bedding, tucking and roughening of wall and floor, backing and dispose rubbish out off the premises complete in all respect all as specified and directed. |
| 43 | Dismantling Stone slabs and tiles of any description or thickness laid, bedded and pointed in any mortar in floors, aprons etc. complete all as specified. |
| 44 | M & L 25mm thick cement concrete type B-0, 1:2:4 (using 12.5 mm graded aggregate) for levelling course in floors complete all as specified and directed. |
| 45 | M&L for Coloured digital dark shade Double charged/ultracharged vitrified tiles 10mm thick in floor exc 0.42Sqm but n.exc 1.00Sqm each tile area set and jointed in neat cement slurry and pointed with white cement with pigment to match the shade of tile over and including screed bedding 15mm in CM 1:6 complete in all respect all as specified and directed. |
| 46 | M&L for Coloured digital dark shade Double charged/ultracharged vitrified tiles but on vertical surface as in dados/skirting over 10.mm thick plaster as backing coat in CM 1:4 all as specified |
| 47 | M&L for non-skid coloured ceramic tiles 7 to 8 mm thick, (square/rectangular), area of each tile exceeding 0.11 sqm but nexc 0.18 sqm, in floors etc. set & jointed, with neat cement slurry and pointed white cement with pigment over 15mm thick screed bed or bedding layer of mortar in cement mortar (1:6) for laying of tiles complete in all respect all as specified and directed. |
| 48 | M&L for Glazed ceramic coloured digital wall tiles joints free of size area exc 0.06Sqm and not exc 0.18Sqm X7-8mm thick set and jointed , Joints are filled with , Fevimate TG tile grout of Dr Fixit over and including 10mm thick rendering in CM 1:4 complete in all respect all as specified and directed. |
| 49 | Supply only Liquid waterproofing compound complete all as specified and directed |
| 50 | M&L for Acid resistant tiles 15mm thick vitreous ceramic, unglazed, set, jointed and pointed in chemical resistant mortar, resin type, in floors set & jointed, with neat cement slurry and pointed white cement with pigment over 15mm thick screed bed or bedding layer of mortar in cement mortar (1:6) for laying of tiles complete in all respect all as specified and directed. |
| 51 | M&L for antistatic epoxy flooring 3mm thick in floors, including a 2mm thick hardener screed compound followed by 1mm layer of semi-liquid epoxy resin for smoothness over a smooth concrete surface complete in all respect all as specified and directed. |
| 52 | M&L Granite stone slab 18 to 19 mm thick machine cut polished of colour as required, bedded and jointed in neat cement slurry and pointed in white cement with pigment to match colour of granite stone with and including screed bed of 20mm thick in cement mortar 1:6 all as directed and specified |
| 53 | M&L for 75 mm thick PCC1:4:8 type D-2 using 40mm graded as in sub base of floor (40 mm graded stone aggregate), finishing even and smooth without using extra cement to received tiles including necessary form work etc complete all as specified and directed. |
| 54 | M&L 20 to 25mm thick prepolished machine cut Kota stone slab as in flooring over and including 15mm thick screed bed in cement mortar 1:6, laid over cement slurry @3 Kg/Sam and jointed with grey cement slurry mixed with pigment to match with shade of slab including molding the edge of slab complete all as specified and as directed. (Note:- The size of Kota stone slab shall not less than 550 mm x 550 mm cut size in flooring and full length single piece in steps, except the location where the balance portion remain less than size as specified above). |
| 55 | M&L 20 to 25mm thick prepolished machine cut Kota stone slab as in riser or vertical surface over or as in skiing and including 10 mm thick rendering in cement mortar 1:4, and jointed with grey cement slurry mixed with pigment to match with shade of slab including molding the edge where as specified and as directedNote The size of Kota stone slab shall not less than 550mm x 550mm cut size as in flooring and full length single piece in steps, except the location where the balance portion remain less than size as specified above). |
| 56 | M&L for 50mm thick type-D-2 1:4:8 (using 40mm graded stone aggregate) as in sub base to receive Chequered Cement Concrete tiles and paver blocks all as specified and directed. |
| 57 | M&L for PU Coating Chequered cement concrete tiles 30cm x 30cm x 25mm thick, set. iointed and pointed in neat cement slurry in floors etc. set and jointed in neat cement slurry and pointed in for laying floor finishes CM (1:4) complete all as specified and as directed white or coloured cement to match including Screed bed (or) bedding layer of mortar 15mm thick |
| 58 | Demolition of reinforced concrete of any description and in any position not otherwise specifically provided for including cutting of reinforcement as required to facilliate demolition complete all as specified and directed. |
| 59 | M&L for cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth on stone walls complete all as specified and directed. |
| 60 | M&L for RCC (nominal mix) type B-0 1:2:4 (12.50mm graded crushed stone aggregate) as in Chajjas slab and the like complete all as specified and directed. |
| 61 | M&L RCC Foundations, including raits, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete uing type M-25(Design mix) (using 20mm graded) stone aggregate complete all as specified. |
| 62 | M&L RCC type B-1 1:2:4 using 20mm graded stone aggregate as in kitchen shelves , manhole cover, etc complete all as specified and directed. |
| 63 | M&L RCC in Columns, pillars, piers, posts and struts uing type M-25(Design mix) (using 20mm graded) stone aggregate complete all as specified. |
| 64 | M&L Reinforced Cement Concrete 1:2:4 type B-1 using 20mm graded stone aggregate in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete (reinforcement to be measured separately). |
| 65 | M&L Mild steel TMT bars 10mm dia & over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality all as specified and directed. |
| 66 | M&L Mild steel TMT bars 6 to 10mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns. hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mmdia or secuting with clips as in stirrups quality complete all as specified. |
| 67 | M&L for use & waste of form work using steel sheets, steel bracing, propping etc around structural members where micro concreting to be done and keeping form work in position till required specified period complete all as specified and directed.Note:- Form work shall be 100% leak proof. For purpose of payment area in touch with concrete shall be measured. |
| 68 | Form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified. |
| 69 | Form work to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified. |
| 70 | Formwork to Chajjas, slab ,chullah hoods, kitchen shelves cupboards, suspended slabs, drain slabs troughs and similar items including edges rough finished surfaces complete all as specified and directed. |
| 71 | Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc20cm wide and sides of RCIPCC bands in walls, horizontal or sloping and sillar work exc 5cm but not exc 10cm wide |
| 72 | Formwork to soffits of slabs n. exc. 200mm thick and similar works rough finished surfaces of concrete complete. |
| 73 | M & L for 75mm thick cement concrete 1:3:6 type C2, with using 40mm graded stone aggregate as in plinth protection finish the surface even and smooth without using extra cement including filling the expansion joints with bitumen filler / filler boards and necessary form work etc complete all as specified and as directed. |
| 74 | Surface excavation in soft/loose soil, not exceeding 30cm deep and averaging 15cm deep and getting out, complete all as specified and directed. |
| 75 | Excavation in trenches in soft/loose soil n exc 1.5m wide and n.exc 1.50m depth getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, complete all as specified. |
| 76 | Excavating in post holes (or similar holes) each in soft/loose soil n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, complete all as specified. |
| 77 | Returning, filling in, including spreading, levelling, watering and well ramming in layers n. exc 25 cm in hard dense soil. |
| 78 | Removing excavated material n. exc. 50m and depositing where directed at a level n. exc. 1.5m above the starting point. |
| 79 | M&L for Cement Concrete (1:3:6) type C-2 using 40mm graded stone aggregate as in foundations, filling and mass concrete |
| 80 | M&L for hard core of gauge n.exc.63mm hand broken bricks,spread and levelled in layer n exc.15cm thick watering and rammed to a true surface complete all as specified and directed. |
| 81 | M&L for 100 mm thick cement concrete type D-2 1:4:8 (40mm graded agg) as in sub floor; complete all as specified and directed. |
| 82 | M & L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 grade with Grey cement and pigment complete all as specified and directed. |
| 83 | M&L Sand filling under floors or in foundations including watering and consoilidation complete all as specified and directed. |
| 84 | M&L for Cement Concrete 1:2:4 type B-0, using 12.5mm graded stone aggregate as in coping and similar work incl necessary form work to obtain a smooth finishes complete all as specified and as directed. |
| 85 | M&L for providing WPC Jalli 24mm thick including fixing materials and frame work complete all as specified and directed. |
| 86 | S& F Floor door stopper of aluminium alloy body and tongue ,anodised ,with hard drawn steel spring ,fixed in floor overall length of cover plate 140mm |
| 87 | M & L for Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed |
| 88 | S & F 12mm Thick Toughen glass partitions, Doors, including all fittings and fixtures, necessary Handles, hinges, and knobs etc as per the existing one complete all as specified and directed. |
| 89 | S & F Aluminium Composite Panel sheet of 3 mm thick with skin thickness of 0.25mm of aluminium on both sides, sandwiched by 2.5mm polyethylene core with PVDF coating of 30 micron fixed with suitable Self Tapping Screws over frame work of anodised aluminium tubular section 25 X 50mm, 2mm thick, duly fixed to wall / ceiling with expansion fastener, having panels not exceeding 1200X1200mm with necessary silicon filling, in approved pattern / size as in column, beam, wall etc. complete all as specified and as directed. Note:- Rate quoted is deemed to be included for necessary MS Scaffolding up to a height of 12m from the GL for carrying out the job. Nothing shall be paid extra on this account. [Make of Aluminium Composite Panel: ALSTRONG / ALCOBOND / ALSTONE] [Make of Aluminium Sections: JINDAL / HINDALCO / INDAL] |
| 90 | S&F for Anodised aluminium with powder coating of any colour thickness of coating not less than 50 microns frame for doors, windows, ventilators & partition with one or more rebates including joining cleat for fixing etc. complete all as specified. |
| 91 | S&F Anodised aluminium ith powder coating of any colour thickness of coating not less than 50 microns window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified. |
| 92 | Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineerin-charge. |
| 93 | S&F Antimicrobial cladding system of thickness 2.5mm of std size 1500x3000mm having tensile strength of 52Mpa, fire resistant, chemical resistant over insulated wall panels as per specifications and drawing complete all as specified. |
| 94 | S&F lnsulated PVC Wall Lining (thickness of PVC wall lining 25mm) consisting of PVC Insulated Panels with wood grain printed PVC sheets having expanded polystyrene (EPS) stuck to 2mm thick plain colour PVC sheet duly fitted into the wall as per specifications and drawing complete all as specified. |
| 95 | M & L for welding in repairs of n exc 6mm thick and not exc 2.5 cm in length as directed. |
| 96 | Resecuring or easing & adjusting, without taking down shutters of any description exc 1 sq. m and n exc. 2 Sq.m each complete all as specified and as directed. |
| 97 | Cutting holes in brick walls exc half brick but not exc one brick walls built in Cement mortar or cement lime mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified and as directed. |
| 98 | S&F in repair for Gypsum ceiling board for ceiling prepainted, perforated finish, 600 x 600 x 9 to 9.5mm thick in size, of approved brand/make, laid over and including grid work of size 600 x 600mm, made out of 0.5mm thick G.I. tee 32 x 24 mm for main, 25x24mm for cross tee and 20 x 20mm angle fixed on wall, powder coated finish on exposed faces of tee and angle. hung from ceiling using 2 mm thick G.I. Suspension wires spaced at 1200 mm on main runners including making niches for fans/light, including dismantling of wall ceiling and boards, (fibere pulp, insulation etc or insulation boards of anythickness including cover fitllets. all as specified and directed. |
| 99 | Supply and laying of CPVC pipes SDR 11 of outer dia 20mm & plain CPVC SDR 11 fittings on walls/ceilings or laying in floors including taking up or down steel water tubing and connections and removal from site 15mm/20mm bore pipe and complete to walls, ceiling or laid in floor all as specified.(Make:- Astral or equiv) |
| 100 | Supply and laying of CPVC pipes SDR 11 of outer dia 25mm & plain CPVC SDR 11 fittings on walls/ceilings or laying in floors including taking up or down steel water tubing and connections and removal from site 15mm/20mm bore pipe and complete to walls, ceiling or laid in floor all as specified.(Make:- Astral or equiv) |
| 101 | S&F in repair Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted & fixed in position all as specified in SSR Part I 500 Ltrs Capacity complete. |
| 102 | S&F in repair Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted & fixed in position all as specified in SSR Part I 1000 Ltrs Capacity complete. |
| 103 | S & F rotational moulded 1000 lit capacity polythelene water storage tanks ( cylindrical verticle with closed top) hoisted and fixed in position all as specified |
| 104 | S&F in Repairs bib taps with wall flange complete all as specified and directed. |
| 105 | S&F in Repairs Angular Stop cock with wall flange 15 mm bore complete all as specified and directed. |
| 106 | S&F in Repair 15 mm dia CP Kithcen Sink mixture for mixing hot and cold water with regular spout without popup waste system complete all as specified. |
| 107 | S&f Sinks without drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers & waste; including bedding in CM to dwarf wall or including fixing cantilever brackets & connecting union to pipe overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified. |
| 108 | S&F Waste fittings 40mm bore, brass, CP for glazed ware sinks, basins, etc. with long screwed shanks & fly-nuts, flange end bedded in red lead cement & other end fixed complete all as specified and directed. |
| 109 | S&F CP Gratings100mm dia complete all as specified. |
| 110 | S & F in repair vitreous china wash hand basin white flat back of size 550x400mm including cutting for and pinning in ends of brackets, brass chromium plated waste fittings complete all as directed and specified. |
| 111 | S&F in repairs centre hole CP basin mixer cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, mixing 'Hot' or 'Cold' water with long screwed shanks and fly nuts, screwed for iron pipe and fixed of bore dia 15mm complete all as specified. |
| 112 | S&F in repair vitreous china wash down water closet pedestal pattern white excluding flushing cistern and flush pipes complete all as specified and as directed . |
| 113 | S&F health faucet with 1 meter long easy flex tube in chrome finish & wall hook, complete all as specified and directed |
| 114 | M&L in repairs PVC valve less,syphonic action type flushing cistern,low level ,white with inlet ball valve,float and handle including brackets and connection to pipe and fixing of chain and pull or lever if any complete all as specified and directed. |
| 115 | S&F white vitreous china counter wash hand basin, of size-410X910X150mm fixed in granite counter by making suitable size hole, new brackets, 32mm dia brass chromium plated waste coupling, CP botle trap complete all as specified |
| 116 | S&F in repair vitreous china urinal bowl urinal flat back, size of 465x355x265mm white (min)with grating and union for discharge pipe, urinal spreader with waste pipe and all fiting for urinal. |
| 117 | S&F in repairs for 600mm x 450mm size beveled edge mirror of 6mm thick selected quality mounted on 6mm thick plywood with chromium plated screws with washer complete all as specified and directed. |
| 118 | S & F in repairs PVC (SWR) nani trap / floor trap plain or multi with stainless steel grating incl joining to waste pipe with solvent cement joint dia of outlet 75mm bore complete all as specified and as directed. |
| 119 | S&F in repair 75mm bore PVC (SWR) bends any radius complete all as specified and as directed. |
| 120 | S&F PVC (SWR) bends of 110mm bore any radius complete all as specified |
| 121 | S & F in repair 110 mm bore PVC (SWR), junction single, (Single T) equal or unequal complete all as specified and directed. |
| 122 | S & F in repair 75 mm bore PVC (SWR), junction single, (Single T) equal or unequal complete all as specified and directed. |
| 123 | S & F in repairs 110mm bore PVC (SWR) pipes singles socket in any length with rubber ring joints fixed to walls / floor or in trenches complete all as specified and as directed. |
| 124 | S & F in repairs 75mm bore PVC (SWR) pipes singles socket in any length with rubber ring joints fixed to walls / floor or in trenches complete all as specified and as directed. |
| 125 | Taking down of old PVC drain pipes from wall/fllor/ceiling/trenches in any position and removing to store complete all as specified. |
| 126 | S&F in repair CP mixer (wall, sink & WHB) for mixing hot & cold water screwed down for iron pipe 15mm bore complete all as specified and as directed. |
| 127 | S&Fixed in repair 125 mm size chromium plated shower rose with siwel joint suitable for 15 mm bore GI pipes comlete all as directed.. |
| 128 | S&F in repairs PVC connection 15mm size with PTMT nuts of length 450 mm long complete all as specified and as directed. |
| 129 | S&F in repair Soap dish, vitreous China white, approximate size 160x 160x90mm complete all as specified and as directed. |
| 130 | S&F in repair Towel Rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minimum weight 190gms) |
| 131 | S & F 20mm bore gun metal globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed. |
| 132 | S & F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with CP bracket guard and railing 60cm long complete Make- Jaquar Cat No - CAN-1173 complete all as specified and as directed. |
| 133 | S&F 75mm stack clamp out of 50mm by 5mm flat iron and 16mm dia around iron stamp incl bolts and nuts and securing ends of clamp to wall or roof complete all as specified and as directed. |
| 134 | S&F 110mm stack clamp out of 50mm by 5mm flat iron and 16mm dia around iron stamp incl bolts and nuts and securing ends of clamp to wall or roof complete |
| 135 | Dismantaling plain or corrugated AC sheeting any gauge, thickness, including nainital or similar pattern roof covering all as specified and directed. |
| 136 | S&F Pre- painted galvalume aluminum zinc coating GI based steel sheet of approved profile of corrugation, 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws all as specified and directed by Engr-in-Charge. |
| 137 | Dismantling structural steel/iron work including doors, gates, posts, purlins but excluding framed truss etc. all as specified and directed. |
| 138 | S&F steel work in tubler trusses/posts/purlins including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1998 grade st-240 all as specified and directed. |
| 139 | M&L cutting crack to 'V' groove section in existing roof cleaning out wetting grouting with cement and sand slurry of 1:3 complete all as specified and directed. |
| 140 | Dismantling/removing of old roof treatment of any type including brick tiles, mud fushka etc to get the original RCC surface,cleaning with water etc complete to receive plaster/PCC and removing the debries out of MOD land all as specified. |
| 141 | Removal of Mud fromm top roof slab any thickness, including plastering and leeping (wether full thickness removed or only a part thereof) complete all as specified and directed |
| 142 | M&L for cement concrete 1:2:4 type B0 (using 12.5mm graded stone aggregate) on roof padding with water proofing compound surface finished even and smooth without using extra cement complete all as specified and directed. (Rate of WPC shall be included in unit rate) |
| 143 | M&L for 10 mm thick rendering over the concrete / brick roof surfaces in cement mortar 1:4 surface with water proofing compound @ 200ml per bag finished even and smooth without using extra cement all as specified and directed. |
| 144 | Cleaning all the dust and loose material by brush/blower/Grinder including removing of vegetation/plantation from the surface. M&L for preparation of roof top surfaces, providing and applying single component elastic cold applied polyurethane modified acrylic roofing system, co elastic technology (CET) based on modified polyurethane and fully fibre reinforced, having Sun Reflectivity index (SR) of 109 on top of concrete roof surfaces. All cracks up to 3 mm at corner joints, channel and parapets should be treated with crack seal. Applying three coats including one coat of primer of ShaliUrethane BTD/ Sikalastic 560/ smart care damp proof-ultra having coverage @ min 0.75kg/m2 and dilution up to 10% and laying reinforced fiber net and applying two coats (without dilution) of shaliUrethane BTD/Sikalastic 560/smart care damp proof ultra @ total consumption 2 kg/m2 in two coats for maintaining minimum dry film thickness 1.5mm and elongation at break of free film of approx 350%. The materials shall be applied with brush or roller, complete in all respect as per the direction of Engineer-in-charge/Consultant (Note :6 Hrs interval between two coat will be maintained). All auxiliary and accessories involved during application should be supplied by single manufacturer as a part of system. Make: STP/Sika/Asian paint or equivalent as approved by GE. Note:- Application of water proofing treatment will be done by Authorised Applicator only. |
| 145 | M&L for water proofing treatment to non accessible roof and edges (vertical or tapered) / sunken portion etc. in following sequence:- (i) Properly cleaning and drying the surface (ii) Applying a coat of bitumen primer @ 1.2Kg/Sqm and primer shall be allowed to dry over night. (iii) Laying APP based modified water proofing membrane of weight not less than 3kg per sqm and thickness not less than 3 mm, with 100mm overlaps, sealed and bonded to the surface by 'torchon' method (iv) Applying two coat of bituminous based aluminum painting @ 0.15 kg/Sqm each coat on water proofing treatment with preparation of surfaces complete all as specified and directed at site. |
| 146 | M&L for providing rust proof /anti corrosive treatment to bars :-(i) cleaning of all exposed bars (new & old) alround(ii) Apply a single coat of Alkaline rust converting primer on alround bars new & old as recommended by the manufactuer(iii) Apply two coats of Epoxy phenolic anti corrosive protective coat on bars alround new & old as recommended by the manufactuer. Note : Anti corrosive treatment shall be continuous espcially in the regions where pitting, imperfections, etc were present on the surface of the bars. It is important that the rear portions of re bars (those towards the concrete substrate) should not be left without coating. |
| 147 | M&L for providing PMM (Polymer modified cementitious mortar) :-(i) Dry sub strate surface and free of debris & dust(ii) Applying Epoxy bond coat on the sound substrate using approved spray machine & ensuring that no pin holes are visible.(In case pin holes are still visible after a coat, a second coat shall be applied to ensure absence of pin holes).(iii) Immediately after application of epoxy bond coat as above apply PMM (Polymer modified cementitious mortar) of 25 mm thickness.Note:- Application of PMM shall be preferably be in coats of appx 10mm thickness. PMM work shall be executed in fairely rapid successions so as entire work is completed with in 30 mins). PMM shall be pre packed ready to use.(iv) PMM surface to be moist cured for three days followed by air curing in temperature as recommended by manufactuer complete all as specified and directed. Please Enable Macros to View BoQ information |
| 148 | M&L for providing PMM (Polymer modified cementitious mortar) :-(i) Dry sub strate surface and free of debris & dust(ii) Applying Epoxy bond coat on the sound substrate using approved spray machine & ensuring that no pin holes are visible.(In case pin holes are still visible after a coat, a second coat shall be applied to ensure absence of pin holes).(iii) Immediately after application of epoxy bond coat as above apply PMM (Polymer modified cementitious mortar) of 25 mm thickness.Note:- Application of PMM shall be preferably be in coats of appx 10mm thickness. PMM work shall be executed in fairely rapid successions so as entire work is completed with in 30 mins). PMM shall be pre packed ready to use.(iv) PMM surface to be moist cured for three days followed by air curing in temperature as recommended by manufactuer complete all as specified and directed. Please Enable Macros to View BoQ information |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
