|
| 1 | Repair to potholes any depth, not exc 1 Sqm each including sweeping free from dust and mud, or water, scoring sunken surfaces in roads, paths, etc. cutting around edges to at least 25 mm in depth, making good by filling in screened & graded road metal, watering and well ramming (including supply of road metal) complete all as specified and directed. |
| 2 | Scarifying or picking gravelled macadam or bituminous macadam surface exc 50mm and n.exc 100 mm deep in area exc 400Sqm and removing n.exe 50 m complete all as specified and directed. |
| 3 | M&L for 7.5 cm thick (compacted thickness) WBM, with coarse aggregates (Granite, trap or basalt) of grading 2 (63 to 40mm size) or of grading 3 (50 to 20mm size), spread, rolled and consolidated to gradient and camber required complete all as specified and as directed by Engr -in Charge |
| 4 | M&L Preparing unsurfaced water bound mecadam surfaces by brushing with wire brushes for removing caked mud etc. sweeping with brooms and finally fanning the cleaned surface with gunny bage to remove all loose dirt etc complete all as specified and as directed |
| 5 | M&L Preparing black top surfaces by brushing with wire brushes for removing caked mud etc. sweeping with brooms and finally fanning the cleaned surface with gunny bage to remove all loose dirt etc complete all as specified and as directed |
| 6 | M&L for applying evenly a priming / tack coat with bituminous primer at 10 kg per 10 Sqm using paving bitumen of grade VG 10 complete all as specified & directed. |
| 7 | M&L for applying evenly a priming / tack coat with bituminous primer at 5 kg per 10 sqm using paving bitumen of grade VG 10 complete all as specified & directed. |
| 8 | M&L Premix bituminous macadam (consolidated thickness 75 mm or less ) laid/spread using mechanical paver with 4% binding content by weight of total mix, using paving bitumin of grade VG 30 rolled and compacted to required gradient and camber Paving bitumen any penetration, spread rolled with 8 ton but not exceeding 10 tonne vibratory power roller and consolidating to required gradient and camber complete all as specified & directed. |
| 9 | M&L for bituminous premix semi dence asphaltic concrete 30mm thick consolidated thick with 5.5% binder content by weight of total mix , using paving bitumin of grade VG 30 laid by machenical paver , rolled and compacted to required camber and gradient with 8 to 10 tonne vibratory power road roller complete all as specified and directed. Note:- (a) premix semi dence asphaltic concrete shall be mixed in hot plant transported from plant to work site and laid/spread by means of mechanical paver.(b) Contractor shall quote his rate on this basis of binder as mentioned in above item if there is any variation in the actual binder content used in lower side, the rate shall be adjusted however no price adjustment shall be made if the binder content works out to more than as specified in Sch 'A' |
| 10 | M&L Moorum/red bajri filling in floors or pavings, or as in road side berms etc laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering as in road side burms as specified and as directed. |
| 11 | M & L for preparing bituminous surfaces of road and marking 2.5mm thick centre lines, stop lines, dashes, arrows etc. and the like n. exc 10cm wide on roads pavements with hot applied thermo plastic road marking paint of approved colour confirming to BS 3262-1989 with special applicator machine all as per manufacturers instruction complete all as specified and directed.Make :-STP Limited ( Shalimark / ShaliMark W), SNI Infratech Pvt Ltd (ESN TRMP), Maruti Bitumen Pvt Ltd (MARUTI REFLO MARK) |
| 12 | Taking down of old precast interlocking paver block and chequered tiles of any size and shape any description and in any position, demolition of loose PCC below the interlocking tiles upto 75mm thick etc, complete all as specified and directed. |
| 13 | M&L for 75mm thck PCC (1:4:8) type D2 (using 40mm graded stone aggregate) as in sub base complete all as specified and directed. |
| 14 | M& L for 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawn, drive ways or light traffic parking etc. of required strength thickness & size /shape made by table vibratory method using PU mould laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting, and proper embedding /laying of interlocking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand, complete all as specified and directed. |
| 15 | M& L for PCC type B1 1:2:4 (20 mmm graded stone aggregate) as in copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly or chamfered angles and throating complete all as specified and directed. |
| 16 | Supply and fixing cat eye solar reflective type of metal body alloy of size 100mm x 100mm x 20mm with PAMA striplens reflector of model No. DA 972.0 fixed with and incl MS stud of suitable size as per manufactures instructions complete all as specified and directed. |
| 17 | S&F in repair Road safety circular mirror polycarbonate along with steel stand fixing the same with suitable sized aluminium alloy rivets @ 20 cm c/c to back support frame of M.S. angle iron of size 25x25x3 mm along with theft resistant measures, mounted and fixed with 2 Nos. M.S. angles of size 35x35x5 mm to a vertical post made up to M.S. Tee section ISMT 50x50x6 mm welded with base plate of size 100x100x5 mm at the bottom end and including making holes in pipes, angles flats, providing & fixing M.S. message plate of required size, steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer (vertical MS-Tee support to be painted in black and white colours).Backside of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coat including fixed in posoition in PCC 1: 2: 4 Type B1 of size @ 600x600x600mm all leads and lifts etc. complete as per drawing , specification and direction of Engineer-in-charge Please Enable Macros to View BoQ information |
