|
| 1 | Item Rate BoQ BoQ_Ver3.0 Item Rate Normal INR Only INR Select, Excess (+), Less (-) Less (-) Tender Inviting Authority: MR. Anukaran J Kandir, Senior Manager (Contract), Contract Cell. GRSE Limited ITEMS : CIVIL WORK AND INTERIOR DECORATION WORKS FOR NSG 30 OFFICE RENOVATION IN GRSE TU UNIT E-Tender No.: SCC/AJK/OT(Web)/Office Renovation/TU/010/ET-3434 Name of the Bidder/ Bidding Firm / Company : PRICE BID : ANNEXURE C(This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender.)NB: (i) UOM=Unit of Measurement; ii) sqm. = square meter, iii) Cum - Cubic Meter iv) Nos.- Numbers NUMBER # TEXT # TEXT # NUMBER # TEXT # NUMBER NUMBER TEXT TEXT # NUMBER # TEXT# TEXT # NUMBER # NUMBER NUMBER NUMBER NUMBER TEXT TEXT NUMBER NUMBER NUMBER NUMBER TEXT TEXT NUMBER NUMBER NUMBER NUMBER TEXT TEXT NUMBER NUMBER NUMBER NUMBER TEXT TEXT NUMBER NUMBER NUMBER NUMBER TEXT TEXT NUMBER NUMBER NUMBER # NUMBER # TEXT TEXT NUMBER # NUMBER # DATE NUMBER # NUMBER # TEXT # Sl.No. Job Description Item No. QUANTITY UOM Estimated Rate Addition / Deduction Addition / Deduction Values Currency Convertion against each Item Quoted Currency in INR / Other Currency UNIT RATE (INR) WITHOUT GST GST PERCENTAGE(%) GST Amount in INR Freight Charges ( Unloading & Stacking) Any Other Taxes/Duties/Levies HSN / SAC Code * Name of Supply State / UT DRGS NO. Name of Supply State / UT Less for Cenvat Credit,if any respect of Supplies Under full Excise Duty Category SAC Name of Supply State / UT TOTAL AMOUNT Without Tax TOTAL AMOUNT With Tax TOTAL AMOUNT In Words |
| 2 | CIVIL INTERIOR |
| 3 | Dismantling Existing Wooden Partition in 1st floor for new as required, including surface preparation, ramming, finishing to take new surface ceiling in complete as per site condition in complete as per site condition. |
| 4 | Dismantling Existing Door in 1st floor for new as required, including surface preparation, ramming, finishing to take new surface ceiling in complete as per site condition in complete as per site condition. |
| 5 | Dismantling Wall Plaster in 1st floor for new as required, including surface preparation, ramming, finishing to take new surface ceiling in complete as per site condition in complete as per site condition. |
| 6 | Provide and lay 15 mm sand cement Plaster : Provide and lay 15 mm sand cement Plaster (1 cement : 6 fine cement) to both faces of 125mm thk partition wall up to ceiling including water curing including scaffolding etc. complete as approved. |
| 7 | Providing waterproofing treatment over concrete tiled roof surface/ roof surface (old) & Toilet walls and floor by the application of two coats of slurry prepared with latex of approved brand, Sica or equivalent water and cement in the proportion of (LP.W. Cement - 1:4:6) by volume, with brush in a time gap of minimum 4(four) hours to 14 (fourteen) hours between the two layers, laying 6mm thick and sand and cement consolidated plaster (1:4) grouting the joints admixed with Plastocrete Super of approved brand 0.2% by weight of cement. providing a second layer of 10 mm thick sand and cement plaster (1:4) admixed with Plastocrete Super for sealing the joints, as above the top surface of the treatment with walls / floor waterproofing in toilets, at any height, any level, finally painted with 2 coats of waterproof paints with matching colour to finishing, with prior approval. |
| 8 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by GRSE, beyond 50 m initial lead, for all leads including all lifts involved. |
| 9 | ALLUMINIUM PARTITION WALLSupply & Installation of 1.5 mm natural color Anodized 67mm x 38mm tube & taper clip with 5mm thick transparent or frosted glass. |
| 10 | ALLUMINIUM GLAZED DOORSupply & Installation of 1.5 mm natural color Anodized 67mm x 38mm tube & taper clip with 5mm thick transparent or frosted glass. Doors with floor spring system. |
| 11 | Providing & fixing Solid Flush Door of 30mm thickness in laminate finish on both sides With Vision Panel of size 300mm x 300mm made of 6mm thk glass .Door to be provided including Handles & necessary hardware fittings. |
| 12 | Providing & fixing Solid Flush Door with access control of 30mm thickness in laminate finish on both sides With Vision Panel of size 300mm x 300mm made of 6mm thk glass .Door to be provided including Handles & necessary hardware fittings. |
| 13 | Supply, fitting, fixing wall panel at specific zone with BWP marine quality 12mm solid ply board with edge finishing- gap finishing - board for wall panelling with post laminated - high pressure laminates 1mm thk- grade I quality suede finish, fixed with seasoned first quality timber with anti- termite treatment - 50mm x 50mm frame work @ 600mm c/c both ways as adjusted - fit to size directly grouted to walls with putty including refurbishment of walls with post treatment – anti-termite treatment to walls /structure /anti-termite paints to wall for protection before fixing the panel boards as specified, polishing. Wall panel runners with panel board including anti- fungus, treatments complete at-site installation, tailor made to Interior dimensions including keeping free space area etc. in complete, with prior approval any colour, shade, texture. |
| 14 | Providing and fixing GRID false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance ? 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlockingT-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications & drawings. |
| 15 | Applying one coat of water thinnable cement primer of approved brand and manufacture on wall, ceiling any surface : Water thinnable cement primer. |
| 16 | Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : Two or more coats on new work |
| 17 | Rendering the surface of walls and ceiling with white cement based wall putty of approved make and brand (1.5mm thick) in affected, damaged area, Birla white or equivalent, with prior approval. |
| 18 | VERTICAL BLINDSProviding & Fixing Vertical Blinds with control unit, shall be made of high grade Polymer . Chain shall be made of plastic beads for operation. Use black out fabric with no openess factor. Make: Nova |
| 19 | VINYL FLOORING(office area)Supplying & laying of approved make and brand of scratch proof, flexible & homogeneous P.V.C. Vinyle flooring conforming to IS:3462 - 1982 in required finish, fixed with synthetic acrylic adhesive after preparing the floor, levelling & smothaning when necessary with suitable putty, as per the design. Skirting Not Included.(i) 1.3 mm thick (Roll)Make: WONDERFLOOR |
| 20 | Providing and fixing of digital artistic self adhesive film on ply and wall surface as per approved shade and design complete with all materials and labour as per manufacture's specifications. |
| 21 | FURNITURE |
| 22 | EXECUTIVE TABLE WITH SIDE COMPOSITE STORAGE UNITSIZE: 1800W X 750D X 750HT TABLE TOP Specifications:Table top: Made of 25mm thick prelaminated particle board (Century/ Green) of approved shade. All the edges of workstation surface shall be provided with machine pressed 2mm thick PVC Edge band finish.Under Structure: Table top is supported on MS Powder coated rectangular Perform \\"D\\" Legs which is made of 40x40x1.6mm vertical member & supporting MS cross beam, which is made of 40 x 40 x 1.6mm rectangular tube and connected to legs with aluminium die cast wing connectors.Modesty Panel: One no. 18mm thick 1700mm width X600mm ht PLPB modesty with machine pressed 2mm thick PVC Edge band finish.Geble end: Two no. 18mm thick 650mm width X600mm ht PLPB modesty with machine pressed 2mm thick PVC Edge band finish.Wire Management: The Raceways are provided below the work surface for carrying wires from one end to other end of the cluster, Size offered is 250mm Ht, Thickness 70mm. Provide with separator for data and power cables. Designed to accommodate 50-60 CAT-6 cables. Wire entry through intermediate leg & 65mm dia grommet hole for wire access.Side Unit: 900 X 450 X 750 side table with storage shelf and shutters, drawers in box section, side table top of 25mm thick, All Curcass will be of 18 mm Prelamainted Particle board along with Back will have 9 mm Prelam Particle. There will have Auto HInges. There will have two nos of Drawer unit at Top with Telescocpic chennal and locking system. All exposed edge cover with 2mm thk PVC edge banding. |
| 23 | EXECUTIVE TABLE WITH SIDE COMPOSITE STORAGE UNITSIZE: 1500W X 750D X 750HT TABLE TOP Specifications:Table top: Made of 25mm thick prelaminated particle board (Century/ Green) of approved shade. All the edges of workstation surface shall be provided with machine pressed 2mm thick PVC Edge band finish.Under Structure: Table top is supported on MS Powder coated rectangular Perform \\"D\\" Legs which is made of 40x40x1.6mm vertical member & supporting MS cross beam, which is made of 40 x 40 x 1.6mm rectangular tube and connected to legs with aluminium die cast wing connectors.Modesty Panel: One no. 18mm thick 1400mm width X600mm ht PLPB modesty with machine pressed 2mm thick PVC Edge band finish.Geble end: Two no. 18mm thick 650mm width X600mm ht PLPB modesty with machine pressed 2mm thick PVC Edge band finish.Wire Management: The Raceways are provided below the work surface for carrying wires from one end to other end of the cluster, Size offered is 250mm Ht, Thickness 70mm. Provide with separator for data and power cables. Designed to accommodate 50-60 CAT-6 cables. Wire entry through intermediate leg & 65mm dia grommet hole for wire access.Side Unit: 900 X 450 X 750 side table with storage shelf and shutters, drawers in box section, side table top of 25mm thick, All Curcass will be of 18 mm Prelamainted Particle board along with Back will have 9 mm Prelam Particle. There will have Auto HInges. There will have two nos of Drawer unit at Top with Telescocpic chennal and locking system. All exposed edge cover with 2mm thk PVC edge banding. |
| 24 | SPARE OFFICE TABLE(WITHOUT SIDE UNIT)SIZE: 1200W X 600D X 750HT TABLE TOP Specifications:Table top: Made of 25mm thick prelaminated particle board (Century/ Green) of approved shade. All the edges of workstation surface shall be provided with machine pressed 2mm thick PVC Edge band finish.Under Structure: Table top is supported on MS Powder coated rectangular Perform \\"D\\" Legs which is made of 40x40x1.6mm vertical member & supporting MS cross beam, which is made of 40 x 40 x 1.6mm rectangular tube and connected to legs with aluminium die cast wing connectors.Modesty Panel: One no. 18mm thick 1400mm width X600mm ht PLPB modesty with machine pressed 2mm thick PVC Edge band finish.Geble end: Two no. 18mm thick 650mm width X600mm ht PLPB modesty with machine pressed 2mm thick PVC Edge band finish.Wire Management: The Raceways are provided below the work surface for carrying wires from one end to other end of the cluster, Size offered is 250mm Ht, Thickness 70mm. Provide with separator for data and power cables. Designed to accommodate 50-60 CAT-6 cables. Wire entry through intermediate leg & 65mm dia grommet hole for wire access. |
| 25 | DOCUMENT STORAGE AT OFFICE AREAPLPB OPENABLE SHUTTERS STORAGESIZE: 900W X 750H X 450DSpecification:The storage top 17mm thick, shutter & sides panel are made of 17mm thick & back panle is made of 09mm thick prelam MDF board of approved shade. All the edges of storage surface shall be provided with machine pressed 2mm thick PVC edge band finish. Openable shutter is considered along with Auto hinges, handle and suitable Locking Facility. All exposed area PVC edge lipping. |
| 26 | Decorative Planter BoxMade of 16mm thick Plywood with both side 0.8 laminate finish of approved shade. All the edges of box surface shall be provided with machine pressed PVC edge band finish. With Paver block & 3 no. Artificial plants and trees with natural tropical trunks and washable leaves.Size: 900w X 150d X 150h |
| 27 | DECORATIVE MS PARTITIONSquare pipe, Powder coating, 3'L x 1'D X 7'HPlanter box making with 18 mm Ply & 1 mm laminate finish.Also Real plants included with pots. |
| 28 | TV UNITProviding & fixing of storage unit made of 18 mm BWP ply with 6mm ply back, 18mm B/B shutter and finished with 1mm laminate on outside and inside finished with balancing laminate with inside shelves as per design.Size-2250x300x450(H) |
| 29 | DISPLAY UNITProviding & fixing of Display unit made of 18 mm MR ply with 6mm ply back, 18mm B/B shelf and finished with 1mm laminate on outside finished with .08 laminate with inside shelves as per design.Size-2400x400x2100(H) |
| 30 | CONFERENCE TABLESIZE: 3000W X 1200D X 750HT TABLE TOPSpecifications:Table top: Made of 25mm thick prelaminated particle board (Century/ Green) of approved shade. All the edges of workstation surface shall be provided with machine pressed 2mm thick PVC Edge band finish.Under Structure: The table top will be supported on the MS Base of minium 50x50 mm with 1.4 mm Thick Square Tube both Verticle and Horizentally .All metal componenet will be finished with 50 minimum 50 micron Powder Caoting with 7 to 8 Trunk processed. There will Have two Nos of POP Up for Wrie Management (8Module ) along with one Nos Vertibrae for Verticle Wire Management. |
| 31 | High Back ChairExecutive Revolving & Tilt Chair: 750mm X 500mm BACK 500mm x 450mm SEAT :High back executive revolving chair with height adjustable and back tilting facility with lumber support. Seat and back made of 12 mm thick hot pressed plywood with good quality rexine finish. \\"Special Cushioned Top\\" of back rest for extra comfort. Arm made of chrome finished tubular pipe with P.U arm rest. 5 prong chrome plated leg with good quality twin wheel castors having telescopic bellows |
| 32 | Mid Back ChairRevolving Chairs For Visitor ( for Executive) :Medium Back with armrest, adjustable height Nylon revolving base and wheels having ergonomic design which gives good sitting posture and good quality cushion foam with good quality easy to clean fabric in good colour and upright position locking. Wheel base(W): 75 cm(+-2 cm) |
| 33 | SOFA 3 Seater: 1. 1950 (L) x 750(D)x 450(H) mm. The seat shall be made of PU foam with Density 28 ± 2 kg / cub. mtr having an additional top layer of super soft PU foam in Density 32 ± 2 kg / cu . upholstered with fabric or leatherette. 2. The back is made of PU foam with Density 28 ± 2 kg / cub. mtr with two additional top layer of supersoftfoam of density 32 ± 2 kg / cubmtr , upholstered with fabric. 3. Understructure is made up of 1.2 ± 0.1 cm. thick hot pressed plywood (moisture resistance & termite proof as per IS: 303) & mahogany of cross section devoid of major knots & surface defects 6 nos. per seat & 3.8 mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose 6 nos. per seat . 4. LEG ASSEMBLY: made of Mahogany Wood with PU polish. |
| 34 | SOFA 2 Seater: 1. 1300 (L) x 750(D)x 450(H) mm. The seat shall be made of PU foam with Density 28 ± 2 kg / cub. mtr having an additional top layer of super soft PU foam in Density 32 ± 2 kg / cu . upholstered with fabric or leatherette. 2. The back is made of PU foam with Density 28 ± 2 kg / cub. mtr with two additional top layer of supersoftfoam of density 32 ± 2 kg / cubmtr , upholstered with fabric. 3. Understructure is made up of 1.2 ± 0.1 cm. thick hot pressed plywood (moisture resistance & termite proof as per IS: 303) & mahogany of cross section devoid of major knots & surface defects 6 nos. per seat & 3.8 mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose 6 nos. per seat . 4. LEG ASSEMBLY: made of Mahogany Wood with PU polish. |
| 35 | Centre TableSupplying, fitting, fixing 1000mm W x 550mm D x 450mm H complete with Melamine Faced Engineered Wood with Melamine Surface.Provision for book storage at the side, with center self. Unique looking top with pipe connections. (PKSS 005) Total in Figures 0.0 0.0 INR Zero Only 4.0 Construction of chamber for 100mm sluice plates item5 10.0 Nos Quoted Rate in Figures Select 0.0 0.0 Zero Only Quoted Rate in Words INR Zero Only Please Enable Macros to View BoQ information |
