|
| 1 | Excavating in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth, for foundation, laying of cables/pipes etc, or for shaft, well, cesspits, manhole, pier holes etc, not exceeding 10Sqm on plan and not exceeding 1.5m in depth and getting out in any type of soil, complete all as specified and directed. |
| 2 | All as per srl item No 1 here-in-before but depth exc. 1.5 m and not exc. 3.0 m |
| 3 | Plain cement concrete type D-2, 1:4:8 (using 40 mm graded crushed stone aggregate) as in foundations, filling and mass concrete, complete all as specified and directed. |
| 4 | Reinforced cement concrete (Design mix) M-25 grade (using 20mm graded crushed stone aggregate) as in foundation including raft footing, foundation beam, plinth beam, bases for columns etc basement slab under reamed piles and mass concrete complete all as specified and directed. |
| 5 | Reinforced cement concrete (Design mix) M-25 grade (using 20mm graded crushed stone aggregate) as in beams, cantilivers, bressummers, lintels over 1.5 m span complete all as specified and directed. |
| 6 | Reinforced cement concrete (Design mix) M-25 grade (using 20mm graded crushed stone aggregate) as in columns, pillars, piers, posts and struts, complete all as specified and directed. |
| 7 | Use and waste of formwork to sides of concrete foundation, footings, bases of columns, raft and raft beams, sides & soffits (if any) of foundation and plinth beams and similar work, vertical or to batter including rough finished surfaces of concrete complete all as specified and directed. |
| 8 | Use and waste of formwork to sides of pillars, struts, piers, columns and stanchions for rough finished surfaces of concrete, square, rectangular or polygonal, complete all as specified and directed. |
| 9 | Use and waste of form work to sides and soffits of flat, lintels etc rough finished etc complete all as specified. |
| 10 | TMT bars 10mm dia & over cut to length bent to shape required including, cranking, bending spirally, hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips, complete all as specified and directed. |
| 11 | All as per Srl item No.10 here-in-before but 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders, complete all as specified and directed. |
| 12 | Brick work with sub class 'B' (old size) bricks, straight or curved on plan to any radius built in cement sand mortar 1:6, complete all as specified and directed. |
| 13 | Rendering 15mm thick in cement mortar 1:4 on other than fair faces of brick work finished even and smooth without using extra cement, complete all as specified and directed. |
| 14 | Rendering 10mm thick in cement mortar 1:4 on fair faces of brick work finished even and smooth without using extra cement, complete all as specified and directed. |
| 15 | Mild steel in hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embedding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc; flat iron fillets ( for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc. and similar work conforming to Fe-290 Gde E-165, complete all as specified and directed. |
| 16 | Galvanised 2 strand, steel barbed wire 2.24 mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins etc as complete all as specified & directed (Each line wire to be measured). |
| 17 | Preparation of newly plastered surface of wall and Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm), complete all as specified and directed. |
| 18 | Preparation of new steel surfaces or iron works of any description, over 10cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 19 | Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed. |
| 20 | Plain cement mortar (1:2:4) type B-1 using 20mm graded crushed stone aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, including necessary formwork (straight or curved complete all as specified and directed. |
| 21 | Returning filling in, with approved excavated soil including spreading levelling watering and well ramming in layers not exceeding 25cm thick complete all as specified and directed. |
| 22 | Removing excavated material (spoils) not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed. |
| 23 | Forming square grooves in plaster n exc 12mm deep and n exc 15mm on face at junction of RCC and brickwork, complete all as specified and directed. |
| 24 | PVC 75 mm Dia (SWR) pipes Type 'A' single socketed, in any length with rubber ring joints, laid in trenches or floors or in walls complete all as specified and directed. Please Enable Macros to View BoQ information |
