|
| 1 | M&L for Repair to potholes any depth, not exc 1 sq m each including sweeping free from dust and mud, or water, scoring sunken surfaces in roads, paths, etc. cutting around edges to at least 25 mm in depth, making good by filling in screened & graded road metal, watering and well ramming (including supply of road metal) complete all as specified and directed by Engr-in-Charge. |
| 2 | Scarifying or picking gravelled, macadam or bituminous macadam surfaces exc 50 mm deep and n.exc. 100 mm deep in area exc 400 sqm including removing scarifying materials out of MoD land complete all as specified and directed by Engr-in-Charge. |
| 3 | M&L for 15 cm thick (compacted thickness) (two layer each layer thick 7.5 cm compacted thickness) WBM, with lime stone, sand stone etc coarse aggregates of grading 2 (63 to 40mm size) or of grading 3 (50 to 20mm size), spread, rolled and consolidated to gradient and camber required using 8-12 ton power roller complete all as specified and directed by Engr-in-Charge. |
| 4 | M&L for Preparing unsurfaced WBM surfaces by brushing with wire brushes for removing caked mud etc. sweeping with brooms and finally fanning the cleaned surface with gunny bags to remove all loose dirt etc complete all as specified and directed by Engr-in-Charge. |
| 5 | M&L for Preparing bituminious mecadam surfaces by brushing with wire brushes for removing caked mud etc. swe eping with brooms and finally fanning the cleaned surface with gunny bags to remove all loose dirt etc complete all as specified and directed by Engr-in-Charge. |
| 6 | M&L for Applying evenly a priming/tack coat of paving bitumen with bituminous primer at 10 kg per 10 sq metre complete all as specified and directed by Engr-in-Charge. |
| 7 | M&L for Premix bituminous, macadam laid/rolled and compacted to required gradient and camber with 4% binder content bitumen of grade VG-40 by wt of total mix (consolidated thickness 75mm or less) complete all as specified and directed by Engr-in-Charge. |
| 8 | M&L for bituminous premix semi -dense asphltic oncrete 40 mm consolidated thickness using paving bitumen VG-40 with 5.5% binder content by weight of total mix rolled and compacted to required camber and gadient complete and rolled with 8 to 12 tonne power roller complete all as specified and directed Note :- (I) In case the binder content by weight of total mix is less than 5.5% as per actual design mix . The price adjustment shall be made as per average rates of all paid voucher for bitumen pertaining to this work . If the total content as per dsign mix is more than 5.5% no price adjustment shall be made for the same. (II) Job mix formula for Semi dense asphaltic concrete shall be obtained from the institutions specified in CA prior to commencement of work and shall be got approved from GE. complete all as specified and directed by Engr-in-Charge. |
| 9 | M & L for preparing bituminous surfaces of road and marking 2.5mm thick centre lines, stop lines, dashes, arrows etc. and the like n. exc 10cm wide on roads pavements with hot applied thermo plastic road marking paint of approved colour confirming to BS 3262-1989 with special applicator machine all as per manufacturers instruction complete all as specified and directed by Engr-in-Charge. |
| 10 | S&F in replacement of 900 mm dia refletive safety traffic mirror for road side walk of stainless steelface 0.90 mm thick large radius of curvature for minimum distance distrotation orange powder coated steel back and hood orange vinyl / extrusion with 75 mm clamp brackets for pole mounting complete all as specified and directed by Engr-in-Charge. |
| 11 | S&F solar cat eye aluminum alloy shall (100% water proofing design according to 65) of size 125mm x 125mm x 25mm (shank 65mm) of high efficiency Mono rystafie solar panel 2.4V/ 0.3 watt one NI-ed rechargeable battery (1.2V/ 1600MA) consisting of super bright LED with 10,000 to 18,000 mcd complete all as specified and directed by Engr-in-Charge. |
| 12 | S&F cat eye solar reflective type of metal body alloy of size 100mm x 100mm x 20mm with PAMA striplens reflector of model No. DA 972.0 fixed with and incl MS stud of suitable size as per complete all as specified and directed by Engr-in-Charge. |
| 13 | S&F of Manufacturing, retro reflective Mandatory/ Regulatory sign boards of 900 mm diametre with support length of 3750 mm and made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type - IV of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter, message (bi-lingual), symbols and borders etc. as per IRC ; 67:2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class -2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm c/c to back support frame of M.S. angle iron of size 25x25x3 mm along with theft resistant measures, mounted and fixed with 2 Nos. M.S. angles of size 35x35x5 mm to a vertical post made up to M.S. Tee section ISMT 50x50x6 mm welded with base plate of size 100x100x5 mm at the bottom end and including making holes in pipes, angles flats, providing & fixing M.S. message plate of required size, steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer (vertical MS-Tee support to be painted in black and white colours).Backside of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coat including all leads and lifts etc. complete as per drawing , specification and direction of Engineer-in-charge. |
| 14 | M&L for Moorum/red bajri filling spread , rolled and consolidated to gradient along side paved road as in berms including surface excavation watering and rolling complete all as specified and directed by Engr-in-Charge. |
| 15 | M&L for PCC 1:2:4 type B2 Mix using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed by Engr-in-Charge. |
| 16 | Demolition of Cement concrete in ground floors and pavings n.exc 15 cm thickness below or above ground level) and removing debris out of MOD land complete all as specified and directed by Engr-in-Charge. |
| 17 | M&L for 100 mm thick PCC type D2 1:4:8 (Using 40 mm graded stone aggr) as in sub base to floors including well compacting & laid to level complete all as specified and directed by Engr-in-Charge. |
| 18 | Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc.,of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed by Engr-in-Charge. |
| 19 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed by Engr-in-Charge. |
| 20 | M&L for two coat of synthetic enamal paint over and including priming coat of primer on new concrete surface including preparation of surface complete all as specified and directed by Engr-in-Charge. |
| 21 | S&F in replacement of ABS plastic speed breaker (ABS material of size 250 X 350 X 50 mm fixed with suitable adhesive and nuts in yellow/black colour and reflector on eighter side clearly visible during night hours complete all as specified and directed by Engr-in-Charge. |
| 22 | S&F in replacement metal tubular dealineator made out of ABS round body fitted with 2 Nos 65 mm dia highly reflective reflectors made out of PMMA and mounted on 45/50 mm dia mild steel pipe of 600 mm height duly powder coated and thermo plastic elastomer 3 bands of green, red and yellow reflector radium tape of 25 mm wide strips with anti theft steel net for reflector protection including embedding in PCC 1:2:4 (150x150x300mm) type B1 complete all as specified and directed by Engr-in-Charge. Please Enable Macros to View BoQ information |
