|
| 1 | Providingand Fixing Geared Sluice Valve (with Cap) of make IVC/VAG including cost of bolts, nuts, rubber rings, insertion complete in all respect as per satisfaction of Engineer-in-Charge (500 mm i/d) |
| 2 | Providing and Fixing Geared Sluice Valve (with Cap) of make IVC/VAG including cost of bolts, nuts, rubber rings, insertion complete in all respect as per satisfaction of Engineer-in-Charge (300 mm i/d) |
| 3 | Providing and Fixing Geared Sluice Valve (with Cap) of make IVC/VAG including cost of bolts, nuts, rubber rings, insertion complete in all respect as per satisfaction of Engineer-in-Charge (250 mm i/d) |
| 4 | Providing and Fixing Geared Sluice Valve (with Cap) of make IVC/VAG including cost of bolts, nuts, rubber rings, insertion complete in all respect as per satisfaction of Engineer-in-Charge (200 mm i/d) |
| 5 | Providing and Fixing Geared Sluice Valve (with Cap) of make IVC/VAG including cost of bolts, nuts, rubber rings, insertion complete in all respect as per satisfaction of Engineer-in-Charge (150 mm i/d) |
| 6 | Providing and Fixing Dual plate check valve of make IVC/VAG including cost of bolts, nuts, rubber rings, insertion complete in all respect as per satisfaction of Engineer-in-Charge (500 mm i/d) |
| 7 | Providing and Fixing Dual plate check valve of make IVC/VAG including cost of bolts, nuts, rubber rings, insertion complete in all respect as per satisfaction of Engineer-in-Charge (300 mm i/d) |
| 8 | Providing and Fixing Dual plate check valve of make IVC/VAG including cost of bolts, nuts, rubber rings, insertion complete in all respect as per satisfaction of Engineer-in-Charge (250 mm i/d) |
| 9 | Providing and Fixing Dual plate check valve of make IVC/VAG including cost of bolts, nuts, rubber rings, insertion complete in all respect as per satisfaction of Engineer-in-Charge (200 mm i/d) |
| 10 | Providing and Fixing Dual plate check valve of make IVC/VAG including cost of bolts, nuts, rubber rings, insertion complete in all respect as per satisfaction of Engineer-in-Charge (150 mm i/d) |
| 11 | Providing and Fixing Air Valve (Standard CI) of make IVC/VAG including cost of bolts, nuts, rubber rings, insertion complete in all respect as per satisfaction of Engineer-in-Charge (150 mm i/d) |
| 12 | Providing and Fixing Air Valve (Standard CI) of make IVC/VAG including cost of bolts, nuts, rubberrings, insertion complete in all respect as per satisfaction of Engineer-in-Charge (100 mm i/d) |
| 13 | Providing and Fixing Air Valve (Standard CI) of make IVC/VAG including cost of bolts, nuts, rubberrings, insertion complete in all respect as per satisfaction of Engineer-in-Charge (80 mm i/d) |
| 14 | Providing and Fixing Dismantling joint 500mm i/d including cost of bolts, nuts, rubber rings, insertioncomplete in all respect as per satisfaction of Engineer-in-Charge (500 mm i/d) |
| 15 | Providing and Fixing Dismantling joint 300mm i/d including cost of bolts, nuts, rubber rings, insertioncomplete in all respect as per satisfaction of Engineer-in-Charge (300 mm i/d) |
| 16 | Providing and Fixing Dismantling joint 250mm i/d including cost of bolts, nuts, rubber rings, insertioncomplete in all respect as per satisfaction of Engineer-in-Charge (250 mm i/d) |
| 17 | Providing and Fixing Dismantling joint 200mm i/d including cost of bolts, nuts, rubber rings, insertioncomplete in all respect as per satisfaction of Engineer-in-Charge (200 mm i/d) |
| 18 | Providing and Fixing Dismantling joint 150mm i/d including cost of bolts, nuts, rubber rings, insertioncomplete in all respect as per satisfaction of Engineer-in-Charge (150 mm i/d) |
| 19 | Providing and Fixing Mechnical joint 500mm i/d including cost of bolts, nuts, rubber rings, insertion complete in all respect as per satisfaction of Engineer-in-Charge (500 mm i/d) |
| 20 | Supply, erection, testing and commissioning of centrifugal Submerged pumpset including end suctionenclosed impeller and volute casing etc. complete in all respects all priming arrangement (Raw Water Centrifugal Submerged Pumpset 30 BHP of water at 20 mtr. Head, 3400 LPM) |
| 21 | Providing and laying Double Flanged (Screwed/ Welded) Centrifugally (Spun) Ductile Iron Pipes ofClass K - 9 conforming to IS : 8329 : DI D/F Pipe 500mm |
| 22 | Providing Fixing Led light of 50watt (Syska, Havells, Philips make) |
| 23 | Providing Fixing Led light of 9watt (Syska, Havells, Philips make) |
| 24 | wall fan of size Sweep 40 cm (400 mm) Speed 1280 rpmPower Input 55 W |
| 25 | Provision for probe radar survey to check any underground obstruction before finalizing the alignment complete in all respect as per approved. |
| 26 | Providing concrete block 1:1-1/2:3 on both ends to plug the annular space between casing and carrier pipe complete in all respect |
| 27 | Supply, erection, testing and commissioning of Dewatering pump with starter and acessoriee, Panel, Cable andPipe and Fittings etc. complete in all respects allpriming arrangement : Dewatering Pump 3 HP |
| 28 | NS Item -Designing, Supply and erection of DG set of eapacity complying to CPCBIV plus norms with noise controlled devices acoustic enclosure of suitable rating, testing and commissioning of diesel generating set, radiator cooled, 3 phase, 4 wire, 50 cycles 415 plus (-)1% volts AC alternator close coupled on a common MS fabricated base frame with diesel engine complete with suitable size incoming cable from generator to change over/AMF/ Sync panel, making 2nd incoming cable connection from transformer, outgoing outgoing cable cable connection connection from changeover/ standard panel, making second incoming cable connection from transformer, DG sets complete as per following from changeover / STD panel to incomer of motor starter panel, fenced enclosure with platform for The rating should be at 1500 RPM. detailed scope and specifications and directions of Engineer-in-charge. a) Diesel Engine b) Alternator c) Battery 12/24 V. d) Base Plate. e) suitable sq mm suitable core copper cable upto 40 metres. f) Tools, standard panel frequency g) Metering meter 415 VAC-1 Indications set in build in Microprocessor with Amp. meter, Volt Meter, ASS, VSS, Phase Indicator, control fuse, with suitable CT`s) h) Metering set 60/5A/110V (Amp. Meter, Volt Meter) in Microprocessor i) Overload protection for DC-1 No.j) Battery Charger 12/24V DC k)Copper bus bar of suitable sizeI) KWH meter m) Starting fuse button and switch on/off) n) Indicating lamps for low lubricated oil pressure, high coolant temperature, set running, load on, Dc control and other required accessories complete in all respects to the satisfaction of Engineer-in-charge. (320 KVA.) |
| 29 | Providing and fixing of suitable floating arm of Fibre metalled and all nuts and bolt SS 304 along with swing bend as per required specifications approved by Engineer-in-charge. (500 MM ) complete in all respects. |
| 30 | NS Item -WTP: Design and construction of 5.00 MLD capacity automated PLC controlled water treatment plantincluding providing and laying the DI/CI pipes, specials,sluice valves from inlet chamber of WTP to inter connecting piping network in WTP (The cost of these DI/CI pipes, valves and specials shall also be included in the rates quoted by the contractor) along with inlet chamber, Alum dozing, Flash mixing, Clariflocculator, filter box, over head Reservoir for back wash and waste water tank with suitable size pumpingsets and panel boards, air scour equipment, chemical housewith chlorination equipments, all other civil, mechanical,electric installations complete in all respects as perspecifications (make of Sluice valves /NRV: IVC/VAG/Kirlosker) : 5 MLD |
| 31 | Supply, erection, testing and commissioning of monoblock vacuum pump with starter, accessories including Panel, Cable ,Pipe etc complete fittng in all respects to fullfill the site requirement Vacuum Pumps 3 HP. |
| 32 | NS Item -AUTOMETIC POWER FACTOR CONTROL PANEL Supply erection testing and commissioning of Automatic Power Factor control panel as per required capacitor complete with digital screen and including Distribution Panel, ACB as required as per site Condition, Coupler, DG Change over specification mentioned in the as per approved DNIT. |
| 33 | Providing and fixing pressure gauge 6` dia 0-20 kg/sqcm as per site required complete in all respect. |
| 34 | HT Panel -Supply Indoor Type 11KV VCB Control Cubical Panel with vertical Isolation Type Breaker as per Relevant IS as amended up to Date and Additional Specifications, having Capacities as Mentioned Below, Single break trip free mechanism, manually charged and Auto/Manually closing breaker suitable for use on 11kv, 3 phase 50hz AC, Supply with short circuit fault level of 800 Amps Capacity, breaker featured with local ON/OFF indicator with hand trip device, spring release coil, shunt trip coil and auxiliary switch of 2NO plus 2NC and equipped with following switchgears and accessories including making suitable structure (such as G.O switch, H Pole and HT cable of required capacity etc. complete in all respect as per site requirement arrangement for installation, control wiring and connections etc. as reqd. (1 IC plus 2 OG) a). VCB, 11KV, 800Amp, 50KA. b). 1ph 11KV/110 Volts PT (indoor type) Class 0.2 Accuracy and 100 VA burden -3 no`s. c). 33KV indoor dead type dual core dual ratio 3CTs of ratio 200-100/5-5 A of 15 VA burden, PS 5 P10 and accuracy class 0.2. d). Control panel- Cubicle type control panel suitable for floor mounting made out of 1.63 mm CR sheet duly powder coated and with following relays. e). Microprocessor based numerical relay for O/L, E/F and SC Protection suitable for above. f). Master trip relay -2 no`s. g). Indicator type Annunciator panel with buzzer. h). Digital Volt Meter-0-11 KV. 1). Digital Amp Meter-0-100 Amp. j). RYB/ Trip/Closing/Spring charged indicator lamp. k). Fault Annunciator panel for O/L, WTI, OTI and Buchhloz Relay Alarm And Trip Auxiliary relay. 1) TNC Switch for Operation. m) Multifunction Meter EM6400NG. n) TCS Relay for Safety..... |
| 35 | ELECTROMAGNETIC FLOW METER AS PER VENDOR LIST and SPECIFICATION AS DEFINE UNDER APPROVED NIT: LINE SIZE : 150 MM LINE: PTFE DISPLAY: DIGITAL MOUNTING: INTEGRAL MEDIUM: WATER TEMPERATURE RANGE: plus 5°C to plus 35°C OPERATING PRESSURE: 0.1 TO 15 BAR PROCESS TEMPERATURE: -40°C TO plus 120°C (PTFE/PFA, COMPACT VERSION) MEASUREMENT PRINCIPLE: ELECTROMAGNETIC MATERIAL: DIE-CAST ALUMINUM (STANDARD), STAINLESS STEEL (OPTIONAL) CONNECTION BOX: ONLY FOR REMOTE VERSIONS PRODUCT FAMILY: OPTIFLUX FOR USE WITH: IFC 050, IFC 100, and including inbuilt dual Sim (4G/5G), LCD display with flow direction, forward and reverse flow rate, cumulative forward flow, device name etc, accuracy shall be as per ISO 4064, class private access on desktop and mobile, secure cloud (Cloud based software comprising of Middle ware, Database and Front-end web interface through suitable Dashboards, Aggregation screens and GIS assisted drill-down from macro to micro to be provided. Application data hosting. Cloud services of Ministry of Electronics and Information Technology (Meity), Government of India empaneled cloud service providers shall be taken. Cloud service provider must adhere the security standards and guidelines issued by Meity from time-to-time. As the data belongs to the State Government of Haryana, therefore the application and data hosted on Cloud must be kept and stored in data centers located in India only. Any change in application requirement or infrastructure shall be borne by the Implementation agency. Implementation agency shall carry out the Application Security Audit from a Certified Auditor (CA). Application and data shall be kept confidential and only the authorized users shall have the access to it. Implementation Agency shall be responsible for any data theft or data leakages.) (INLINE FLANGE TYPE) |
| 36 | ELECTROMAGNETIC FLOW METER AS PER VENDOR LIST and SPECIFICATION AS DEFINE UNDER APPROVED NIT: LINE SIZE : 250 MM LINE: PTFE DISPLAY: DIGITAL MOUNTING: INTEGRAL MEDIUM: WATER TEMPERATURE RANGE: plus 5°C to plus 35°C OPERATING PRESSURE: 0.1 TO 15 BAR PROCESS TEMPERATURE: -40°C TO plus 120°C (PTFE/PFA, COMPACT VERSION) MEASUREMENT PRINCIPLE: ELECTROMAGNETIC MATERIAL: DIE-CAST ALUMINUM (STANDARD), STAINLESS STEEL (OPTIONAL) CONNECTION BOX: ONLY FOR REMOTE VERSIONS PRODUCT FAMILY: OPTIFLUX FOR USE WITH: IFC 050, IFC 100, and including inbuilt dual Sim (4G/5G), LCD display with flow direction, forward and reverse flow rate, cumulative forward flow, device name etc, accuracy shall be as per ISO 4064, class private access on desktop and mobile, secure cloud (Cloud based software comprising of Middle ware, Database and Front-end web interface through suitable Dashboards, Aggregation screens and GIS assisted drill-down from macro to micro to be provided. Application data hosting. Cloud services of Ministry of Electronics and Information Technology (Meity), Government of India empaneled cloud service providers shall be taken. Cloud service provider must adhere the security standards and guidelines issued by Meity from time-to-time. As the data belongs to the State Government of Haryana, therefore the application and data hosted on Cloud must be kept and stored in data centers located in India only. Any change in application requirement or infrastructure shall be borne by the Implementation agency. Implementation agency shall carry out the Application Security Audit from a Certified Auditor (CA). Application and data shall be kept confidential and only the authorized users shall have the access to it. Implementation Agency shall be responsible for any data theft or data leakages.) (INLINE FLANGE TYPE) |
| 37 | ELECTROMAGNETIC FLOW METER AS PER VENDOR LIST and SPECIFICATION AS DEFINE UNDER APPROVED NIT: LINE SIZE : 500 MM LINE: PTFE DISPLAY: DIGITAL MOUNTING: INTEGRAL MEDIUM: WATER TEMPERATURE RANGE: plus 5°C to plus 35°C OPERATING PRESSURE: 0.1 TO 15 BAR PROCESS TEMPERATURE: -40°C TO plus 120°C (PTFE/PFA, COMPACT VERSION) MEASUREMENT PRINCIPLE: ELECTROMAGNETIC MATERIAL: DIE-CAST ALUMINUM (STANDARD), STAINLESS STEEL (OPTIONAL) CONNECTION BOX: ONLY FOR REMOTE VERSIONS PRODUCT FAMILY: OPTIFLUX FOR USE WITH: IFC 050, IFC 100, and including inbuilt dual Sim (4G/5G), LCD display with flow direction, forward and reverse flow rate, cumulative forward flow, device name etc, accuracy shall be as per ISO 4064, class private access on desktop and mobile, secure cloud (Cloud based software comprising of Middle ware, Database and Front-end web interface through suitable Dashboards, Aggregation screens and GIS assisted drill-down from macro to micro to be provided. Application data hosting. Cloud services of Ministry of Electronics and Information Technology (Meity), Government of India empaneled cloud service providers shall be taken. Cloud service provider must adhere the security standards and guidelines issued by Meity from time-to-time. As the data belongs to the State Government of Haryana, therefore the application and data hosted on Cloud must be kept and stored in data centers located in India only. Any change in application requirement or infrastructure shall be borne by the Implementation agency. Implementation agency shall carry out the Application Security Audit from a Certified Auditor (CA). Application and data shall be kept confidential and only the authorized users shall have the access to it. Implementation Agency shall be responsible for any data theft or data leakages.) (INLINE FLANGE TYPE) |
| 38 | Boaring by HDD: Horizontal boaring of size 600mm i/d of thickness 20mm by augar boaring machine by trenchless technology complete in all respect. MS PIPE: Providing, insertion, of 600 mm i/d MS Casing Pipe having thickness of 20 mm including cutting, joint including and radiographycally welding of MS pipe with coating on inner and outer side of pipe with built oxypaint of thickness 250 micron complete in all respect |
| 39 | Providing and insertion of 300 mm i/d MS Carrier Pipe having thickness of 12.5 mm including cutting, joint including and radiographycally welding of MS pipe with coating on inner and outer side of pipe with built oxypaint of thickness 250 micron and complete in all respect.Providing and fixing HDPE spacer to be fitted in MS casing pipe of size 600mm i/d and carrier pipe of size 300mm i/d complete job including labour charge of material to site of work complete in all respect as per satisfaction of Engineer-in -charge. |
| 40 | Operation and maintenance for complete scope of work mentioned in DNIT i.e Design, construction, commissioning and testing Proposed water works Asrawas (5.00 MLD WTP) and laying of Rising mains complete in all respect and its Raw water Rising Mains etc. complete scope of work under this contract as per schedule –IV for a period of 06 Years defect liability cum Operation and Maintenance period (After Successful completion of 3 Months Trial run Period) on terms as per letter issued by Project Director Haryana (HEWP) vide memo no. 11296-11352/HEWP dated 10/02/2026 complete in all respect as per approved DNIT (Will be Charged to the A/Mtc estimate). |
| 41 | HSR Itmes(As per uploaded DNIT) Please Enable Macros to View BoQ information |
