Tender For Providing Of Sewer Network And House Connection Work In Ramnagar Zone (Extended Area) Of Nagar Nigam Varanasi, Distt-Varanasi, Ramnagar-Uttar Pradesh

TDR : 55110562

Tender Notice
BOQ

13 Days Left

Ramnagar , Uttar Pradesh

Tender Brief : Tender For Providing Of Sewer Network And House Connection Work In Ramnagar Zone (Extended Area) Of Nagar Nigam Varanasi, Distt-Varanasi

Document Fees
₹ 23600 /-

EMD
₹ 15336000.0 /-

Tender Value
₹ 153.35 Crore /-

Submission Date
30-04-2026

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	Civil Work
2	Sewer Network
3	Execavation
4	Excavation for following depth below G.L. for laying of sewers in ordinary soil earth, sand, loam and clay including cutting of jointing pits, trimming dressing leveling refilling of trenches in 20cm layers watering and ramming the same including removal of surplus earth or other dismantled materials up to distance 8KM from the centre of trenches.
5	0.00 - 1.50 m BGL
6	1.51 - 3.00 m BGL
7	3.01 - 4.50 m BGL
8	4.51 - 6.00 m BGL
9	6.01 - 7.50 m BGL
10	7.51 - 9.00 m BGL
11	TIMBERING
12	Providing and fix open timbering (covering 1/3rd) of surface area by planks in trenches for the following depth below G.L. Consisting of 40 mm approved country wood planks for poling boards 125mm x 75mm Indian Sal wood walers and 100 mm dia. Sal ballies for shuttering at 1.5m c/c including removal after laying. Both sides will be taken as one side for the purpose of payment and measurements i.e. area equals to length x depth of trenches and dismantled timbering materials will be the property of the contractor.
13	0.00 - 3.00 m BGL
14	Providing and fix close timbering in the trenches for the following depth below G.L. consisting of 40 mm approved country wood planks for poling broads 125 mm x 75 mm Indian Sal wood walers and 100 mm dia. Sal bellies for truing the shuttering at 1.5 M c/c/ including removal after laying of sewers. Both side of trenches will be taken as one side for the purpose of payment and measurement i.e. area equals to length x depth of trenches. Dismantled timbering materials will be the property of the contractor.
15	0.00 - 3.00 m BGL
16	3.01 - 6.00 m BGL
17	6.01 - 9.00 m BGL
18	Laying of Sewer Network
19	Supply of following sizes of RCC NP3/NP4 S&S rubber rings joints pipe ,dewatering & rubber ring from factory to site of work including transportations loading, unloading, stacking all taxes excise duty transit insurance etc. complete.
20	200 mm dia pipe
21	250 mm dia pipe
22	300 mm dia pipe
23	350 mm dia pipe
24	400 mm dia pipe
25	450 mm dia pipe
26	500 mm dia pipe
27	600 mm dia pipe
28	700 mm dia pipe
29	800 mm dia pipe
30	200 mm dia pipe
31	250 mm dia pipe
32	300 mm dia pipe
33	350 mm dia pipe
34	400 mm dia pipe
35	450 mm dia pipe
36	500 mm dia pipe
37	600 mm dia pipe
38	700 mm dia pipe
39	800 mm dia pipe
40	Carting of following sizes of RCC NP3/NP4 S&S rubber rings joints pipe & rubber ring from store to site of work, lowering gasket the same into trenches and laying true to the alignment and gradient including excavation of earth below invert level of pipes cost of all jointing materials, testing etc. complete.
41	200 mm dia pipe
42	0.00 - 1.50 m BGL
43	1.51 - 3.00 m BGL
44	3.01 - 4.50 m BGL
45	4.51 - 6.00 m BGL
46	6.01 - 7.50 m BGL
47	7.51 - 9.00 m BGL
48	250 mm dia pipe
49	0.00 - 1.50 m BGL
50	1.51 - 3.00 m BGL
51	3.01 - 4.50 m BGL
52	4.51 - 6.00 m BGL
53	6.01 - 7.50 m BGL
54	7.51 - 9.00 m BGL
55	300 mm dia pipe
56	0.00 - 1.50 m BGL
57	1.51 - 3.00 m BGL
58	3.01 - 4.50 m BGL
59	4.51 - 6.00 m BGL
60	6.01 - 7.50 m BGL
61	7.51 - 9.00 m BGL
62	350 mm dia pipe
63	0.00 - 1.50 m BGL
64	1.51 - 3.00 m BGL
65	3.01 - 4.50 m BGL
66	4.51 - 6.00 m BGL
67	6.01 - 7.50 m BGL
68	7.51 - 9.00 m BGL
69	400 mm dia pipe
70	0.00 - 1.50 m BGL
71	1.51 - 3.00 m BGL
72	3.01 - 4.50 m BGL
73	4.51 - 6.00 m BGL
74	6.01 - 7.50 m BGL
75	7.51 - 9.00 m BGL
76	450 mm dia pipe
77	0.00 - 1.50 m BGL
78	1.51 - 3.00 m BGL
79	3.01 - 4.50 m BGL
80	4.51 - 6.00 m BGL
81	6.01 - 7.50 m BGL
82	7.51 - 9.00 m BGL
83	500 mm dia pipe
84	0.00 - 1.50 m BGL
85	1.51 - 3.00 m BGL
86	3.01 - 4.50 m BGL
87	4.51 - 6.00 m BGL
88	6.01 - 7.50 m BGL
89	7.51 - 9.00 m BGL
90	600 mm dia pipe
91	0.00 - 1.50 m BGL
92	1.51 - 3.00 m BGL
93	3.01 - 4.50 m BGL
94	4.51 - 6.00 m BGL
95	6.01 - 7.50 m BGL
96	7.51 - 9.00 m BGL
97	700 mm dia pipe
98	0.00 - 1.50 m BGL
99	1.51 - 3.00 m BGL
100	3.01 - 4.50 m BGL
101	4.51 - 6.00 m BGL
102	6.01 - 7.50 m BGL
103	7.51 - 9.00 m BGL
104	800 mm dia pipe
105	0.00 - 1.50 m BGL
106	1.51 - 3.00 m BGL
107	3.01 - 4.50 m BGL
108	4.51 - 6.00 m BGL
109	6.01 - 7.50 m BGL
110	7.51 - 9.00 m BGL
111	Bedding
112	Cement concrete work in bedding below G.L. at specified depth with cement, coarse sand and 20 mm gauge approved stone ballast (1:2:4) including supply of all materials, labour, T&P etc. required for the proper completion of work.
113	0.00 - 1.50 m BGL
114	1.51 - 3.00 m BGL
115	3.01 - 4.50 m BGL
116	4.51 - 6.00 m BGL
117	6.01 - 7.50 m BGL
118	7.51 - 9.00 m BGL
119	Lean Cement concrete work in bedding below G.L. at specified depth with cement, coarse sand and 20 mm gauge approved stone ballast (1:4:8) including supply of all materials, labour, T&P etc. required for the proper completion of work.
120	0.00 - 1.50 m BGL
121	1.51 - 3.00 m BGL
122	3.01 - 4.50 m BGL
123	4.51 - 6.00 m BGL
124	6.01 - 7.50 m BGL
125	7.51 - 9.00 m BGL
126	Well graded crushed rock/ gravel max size 25mm including supply of all materials, labour, T&P etc. into the trenches for bedding of DWC/RCC Pipes including watering compaction, labour T&P etc. for completion of work.
127	0.00 - 1.50 m BGL
128	1.51 - 3.00 m BGL
129	3.01 - 4.50 m BGL
130	4.51 - 6.00 m BGL
131	6.01 - 7.50 m BGL
132	7.51 - 9.00 m BGL
133	Construction of circular type brick masonary/RCC manhole (with Extra Heavy Duty type manhole cover) with top slab made of cement concrete 1:1.5:3 with graded granite stone aggregate (12 mm nominal size), foundation concrete 1:4:8 graded stone aggregate other than granite 40mm nominal size, wall made of brick masonry using 1st class bricks having crushing strength between 100 to 149 kg/cm² in cement mortar 1:4 inside plastering 12 mm thick 1:3 finished smooth with neat cement, pinning, outside plaster 1:4 and making channels with cement concrete 1:2:4 graded granite stone aggregate (12 mm nominal size) complete as per specifications.
134	900mm internal dia., 1.65m deep
135	1200mm internal dia., 2.30m deep
136	1500mm internal dia., 4.95m deep
137	1500mm internal dia., 9.0 m deep
138	Same as item no 135 for Regulation of Shafts plus/minus from the above mentioned depth
139	900mm internal dia., 1.65m deep
140	1200mm internal dia., 2.30m deep
141	1500mm internal dia., 4.95m deep
142	1500mm internal dia., 9.0 m deep
143	Dismantling/Cutting of the following type of road for laying sewers, manholes, sewer connection chambers etc. including shorting out and stacking serviceable materials and disposal of unserviceable materials upto distance of 50 m.
144	Bituminous road
145	Concrete road
146	Interlocking tile road
147	B.O.E road
148	Permanent re-instatement of the following ty pe of road surface after laying of sewer line including supply of all materials, labour, T&P etc. required for completion of work. it also includes necessary excavation required for preparation of trench for reinstatement of road, disposal of surplus unserviceable material, watering, ramming, cleaning surface for proper completion of the work as per directions of Engineer ‐in ‐charge.
149	Bituminous road (PWD) -(20cm sand, 20cm GSB, 20cm WMM, 5 cm to 8 cm DBM, 3cm to 4 cm B.C.) payment made upto WMM- 50%, DBM- 30% and BC with testing in NABL aprooved lab/PWD- 20%
150	Bituminous road (Nagar Nigam) (20cm sand, 20cm GSB, 20cm WMM, 5 cm to 8 cm DBM, 3cm to 4 cm B.C.) payment made upto WMM- 50%, DBM- 30% and BC with testing in NABL aprooved lab/PWD- 20%
151	C.C. Road in M25 grade, minimum thickness 15cm on 20cm th. sand & 15 .cm th. PCC (M15) filling base & 10 cm GSB
152	Interlocking Road (existing usable Interlocking bricks M-30 grade, on 20cm local sand & 10cm TH. PCC 1:6:12). Incl. Entire surface Spreading 3 cm local sand for paste of brick & joint filling
153	BOE Road (15 Cm. sand with first class brick 50% New and 50% Old)
154	Supply of MS pipe (As per IS:3589 made from steel confirming to IS:2062), with anti corrosive treatment with P.U. coating and Installation of product pipe by HDD method including preparing and setting up the plants and equipement, preparing new pipe work material, installation new pipe-work and commissioning system or making the system ready for commissioning by HDD operation including, all related civil and mechanical works like excavation, shoring/strutting, etc. drilling, stringing, reaming, and pulling back the new pip-work on the designed bore path alignment, proper disposal of drilling fluid, and back fill of site after completion all inclusive as per IndSTT:101:2018: Code of prectice of HDD Technique Suiting Indian Conditions.
155	200 mm dia pipe, 6mm Pipe Wall Thickness
156	250 mm dia pipe, 6mm Pipe Wall Thickness
157	300 mm dia pipe, 6mm Pipe Wall Thickness
158	350 mm dia pipe, 6mm Pipe Wall Thickness
159	400 mm dia pipe, 6mm Pipe Wall Thickness
160	450mm dia pipe, 8mm Pipe Wall Thickness
161	Provision for laying of sewer by Trenchless Technology including Supply of different size of MS Pipe, Labour T&P etc. required for Proper Completion of the Work.
162	500 mm (with 12 mm thick M.S. pipe cost)
163	600 mm (with 12 mm thick M.S. pipe cost)
164	700 mm (with 12 mm thick M.S. pipe cost)
165	800 mm (with 12 mm thick M.S. pipe cost)
166	Providing and erecting temporary barricading at site as per drawing/ direction of Engineer-in-Charge which includes hiring of Eucalyptus Ballies and arrangement for traffic diversion such as traffic signals during construction at site as directed by the Engineer-in-Charge. The barricading provided shall be retained in position at site continuously i/c shifting of barricading from one location to another location as many times as required during the execution of the entire work till its completion. Rate include its maintenance for damages, painting, all incidentals, labour materials, equipments and works required to execute the job. The barricading shall not be removed without prior approval of Engineer-in-Charge. (Note :- One time payment shall be made for providing barricading from start of work till completion of work i/c shifting. The barricading provided shall remain to be the property of the contractor on completion of the work). The rate is for unit length of pipe laying.
167	Disposal of Surplus Earth
168	Diversion of Existing Sewer line during laying of New Sewer includding Supply of 7.1 mm thick MS pipe size 200 mm dia and as per requirement of site condition including cost of ms pipe ms bend flange nut volt rubber packing also including hiring of DG set welding machine and gas cutter all labour material etc complete10% of Total Length and re- use of pipe
169	Dewatering work during laying of pipe line and construction of manhole
170	Provision for Sand filling in trench for cuision of pipe
171	Provision for shifting and reinstatement of electric and telephone poles during excavation and laying of sewer lines.
172	Provision for shifting of electric and telephone cable, gas pipeline, existing water supply mains falling in the alignment of conveying main during excavation and the restoring utilities / services to its original condition. etc. during excavation and laying of sewer lines.
173	Sewer House Connection
174	Construction of House Connecting chambers for two connections of size 0.6 x 0.6 x 0.75m
175	Making Domestic Sewer connection using 110mm HDPE pipe PN-6, PE-100
176	Laying of Sewer line from House Connecting chambers to M.H using 160mm HDPE pipe PN-6, PE-100
177	Sewer inter connecting chamber to intercept the waste water from toilet,kitchen and bathroom 0.3x0.3x0.45m
178	Rising Main
179	Execavation
180	Excavation for following depth below G.L. for laying of sewers in ordinary soil earth, sand, loam and clay including cutting of jointing pits, trimming dressing leveling refilling of trenches in 20cm layers watering and ramming the same including removal of surplus earth or other dismantled materials up to distance 50m from the centre of trenches.
181	0.00 - 1.50 m BGL
182	Providing, Supplying, laying, jointing & field testing at site as per specifications of centrifugally cast (spun) following dia Pressure Pipes with epoxy internal coaating and externally painting for sewerage confirming to IS 8329:2000 (amended upto date) with push on type EPDM 'ISI marked' rubber gasket (including cost of rubber gasket) joining as per IS 5382 specifications. Pipes shall be out side Zinc coated with finishing layer of Bitumen and have factory internal cement mortar lining. The rates include all the cost of material, cost of specials, all local and central taxes, labour required, transportation, loading, unloading, conveyance to site and stacking including lowering, laying & jointing with DI pipes and specials, etc. complete and giving satisfactory hydraulic field testing, commissioning as per specifications etc., complete as directed by Engineer. The pipe shall be ISI marked.
183	300mm Dia DI K-9
184	450mm dia DI K-9
185	Providing, Erecting, Testing, Commissioning, of C.I. double ball orifice type 100 mm dia Air Valve inclusive of all taxes, transportation, insurance, Confirming to IS. With Construction of 350x350x500 mm size air valve chamber as per type design including supply & fixing of 50 mm dia medium duty perforated C.I. cover.
186	Dismantling/Cutting of the following type of road for sewer house connection including shorting out and stacking serviceable materials and disposal of unserviceable materials upto distance of 50 m.
187	Bituminous road
188	Permanent re-instatement of the following ty pe of road surface after laying of sewer line including supply of all materials, labour, T&P etc. required for completion of work. it also includes necessary excavation required for preparation of trench for reinstatement of road, disposal of surplus unserviceable material, watering, ramming, cleaning surface for proper completion of the work as per directions of Engineer ‐in ‐charge.
189	Bituminous road (Nagar Nigam)
190	Disposal of Surplus Earth
191	Provision for Sand filling in trench for cuision of pipe
192	Effluent Line
193	Execavation
194	Excavation for following depth below G.L. for laying of sewers in ordinary soil earth, sand, loam and clay including cutting of jointing pits, trimming dressing leveling refilling of trenches in 20cm layers watering and ramming the same including removal of surplus earth or other dismantled materials up to distance 50m from the centre of trenches.
195	0.00 - 1.50 m BGL
196	1.51 - 3.00 m BGL
197	TIMBERING
198	Providing and fix open timbering (covering 1/3rd) of surface area by planks in trenches for the following depth below G.L. Consisting of 40 mm approved country wood planks for poling boards 125mm x 75mm Indian Sal wood walers and 100 mm dia. Sal ballies for shuttering at 1.5m c/c including removal after laying. Both sides will be taken as one side for the purpose of payment and measurements i.e. area equals to length x depth of trenches and dismantled timbering materials will be the property of the contractor.
199	0.00 - 3.00 m BGL
200	Supply, Carting of following sizes of RCC NP3/NP4 S&S rubber rings joints pipe & rubber ring from factory to site of work, lowering gasket the same into trenches and laying true to the alignment and gradient including excavation of earth below invert level of pipes cost of all jointing materials, testing etc. complete. also including transportations loading, unloading, stacking all taxes excise duty transit insurance etc. complete.
201	NP3 600 mm dia pipe
202	1.51 - 3.00 m BGL
203	Bedding
204	Well graded crushed rock/ gravel max size 25mm including supply of all materials, labour, T&P etc. into the trenches for bedding of DWC/RCC Pipes including watering compaction, labour T&P etc. for completion of work.
205	1.51 - 3.00 m BGL
206	Construction of circular type brick masonary/RCC manhole (with Extra Heavy Duty type manhole cover) with top slab made of cement concrete 1:1.5:3 with graded granite stone aggregate (12 mm nominal size), foundation concrete 1:4:8 graded stone aggregate other than granite 40mm nominal size, wall made of brick masonry using 1st class bricks having crushing strength between 100 to 149 kg/cm² in cement mortar 1:4 inside plastering 12 mm thick 1:3 finished smooth with neat cement, pinning, outside plaster 1:4 and making channels with cement concrete 1:2:4 graded granite stone aggregate (12 mm nominal size) complete as per specifications.
207	1200mm internal dia., 2.30m deep
208	Providing and erecting temporary barricading at site as per drawing/ direction of Engineer-in-Charge which includes hiring of Eucalyptus Ballies and arrangement for traffic diversion such as traffic signals during construction at site as directed by the Engineer-in-Charge. The barricading provided shall be retained in position at site continuously i/c shifting of barricading from one location to another location as many times as required during the execution of the entire work till its completion. Rate include its maintenance for damages, painting, all incidentals, labour materials, equipments and works required to execute the job. The barricading shall not be removed without prior approval of Engineer-in-Charge. (Note :- One time payment shall be made for providing barricading from start of work till completion of work i/c shifting. The barricading provided shall remain to be the property of the contractor on completion of the work). The rate is for unit length of pipe laying.
209	Providing and erecting 2.00 metre high temporary barricading at site as per drawing/ direction of Engineer-in-Charge which includes writing and painting, arrangement for traffic diversion such as traffic signals during construction at site for day and night, glow lamps, reflective signs, marking, flags, caution tape as directed by the Engineer-in-Charge. The barricading provided shall be retained in position at site continuously i/c shifting of barricading from one location to another location as many times as required during the execution of the entire work till its completion. Rate include its maintenance for damages, painting, all incidentals, labour materials, equipments and works required to execute the job. The barricading shall not be removed without prior approval of Engineer-in-Charge.
210	Disposal of Surplus Earth
211	Provision for Sand filling in trench for cuision of pipe
212	SEWAGE PUMPING STATION (SPS)
213	Design, Construction, Supply of all materials, Erection and Commissioning of SPS (11.0 MLD) with all the civil, LT/HT panel Room, DG set foundation, Pump House, Boundry wall, Internal Road, Gate etc. all complete including all neccessary work as neccesity.
214	Design, Construction, Supply of all materials, Erection and Commissioning of SPS (04.0 MLD) with all the civil, LT/HT panel Room, DG set foundation, Pump House, Boundry wall, Internal Road, Gate etc. all complete including all neccessary work as neccesity.
215	Sewage Treatment Plant (10.0 MLD)
216	Design, Construction, Supply of all materials, Erection and Commissioning of STP (10.0 MLD Sewage Treatment Plant ) with all the civil, electrical, mechanical, instrumentation and scada system, LT/HT panel, sub station building, DG set foundation, admin buidling, Staff Quarter, laboratories, meter room, Boundry wall, Internal Road, Gate etc. all complete with co-treatment facilities. The quality of treated effluent shall be as per CPHEEO Manual for agricultural uses. The rate is considered for SBR Technology. The STP shall be capable to treat the raw sewage having minimum concentration mentioned in CPHEEO manual's table 5.4. including all electrical/mechanical parts along with the power connection charges from hydle from a independent feeder
217	E&M Works
218	(A) SPS-1
219	VFD starter For 50 HP pump set
220	SUBMERSIBLE PUMP SET:
221	Submersible sewage non-clog pumps withJacket cooled Integreated Motor of IP 68Protection for 400±10% V AC, 3phase 50 Hz. suitable to pump raw sewage with specific gravity of 1.05 and also capable to handle solids up to 135mm size with all suitable piping and specials having following material of construction.Casing- 2%NiCIImpeller- ASTM CF8MShaft & Shaft sleeve- ASTM SS 410 included Automatic Coupling system,Guide rail system comprises of Pedestal, bracket, upper guide rail holder,Guide pipe for above 6 sets pumps length upto sumpwell floor level. etc.
222	86 LPS, 25 m Head, 980 RPM
223	CAPACITOR:
224	Provision for supply of shunt type power factor improvement capacitor of suitable to boost the power factor up to 0.95.as per direction of engineer incharge
225	MAIN PIPING & VALVES:
226	Provision for main piping and valves for 250 mm dia, and 450 mm dia common header line(sizes can be change as per site condition & requirement)
227	Motor operated Sluice Valve with actuator
228	CIDF 450 mm ø
229	CIDF 250 mm ø
230	Reflex Valve
231	CIDF 250 mm ø
232	CIDF 450 mm ø
233	CIDF Pipe dia 450 mm
234	CIDF Pipe dia 250 mm
235	Pipe fittings as CIDF Tee 250x 450 mm.SS blind flange dia 250 mm,90 degree bend dia 450 mm,90 degree bend dia 250 mm,90 degree duckfoot bend dia 250 mm,Reducer/Enlarger CIDF Reducer/Enlarger 200 mmx 250 mm ,CIDF 90 degree duckfoot bend dia 200 mm asper site requirements
236	Dismenaling joints 250 mm
237	Dismenaling joints 450 mm
238	Nut and bolts with washer(SS) M20x120,M24x120,M27x140 as per site requirements
239	Necessary Piping , pump set & valve foundation , rubber packing, insertion and other material as per required/direction of engineer incharge.
240	Electromagnetic Flow Meter:
241	(i) Providing, Installation, Testing and commissioning of 450 mm ELECTRO MAGNETIC FLOW METER cum totalizer having following charecteristics/MOC: Liner: Polyurethane or Hard Rubber / Electrode MOC: SS316L /Housing : Die Cast Aluminium or CS / Power Supply: 90-230 V AC / Output: 4-20mA with HART / Sensor Cable : 10 mt / Flow Tube or Sensor housing protection IP68 / Process Flange : SS316 / Display : 3 1/2 LCD Display / Cable Connection : 1/2\\"NPT /Accuracy : 0.5%
242	(ii) CVT with control cables
243	Supply, installation and commissioning of 3 T Mono Rail Single Girder having suitable lift with chain, pulley block and traveling trolley complete
244	Tools & Plants as per mentioned in tender documents and direction of engineer incharge
245	Supply of 5 kg Capacity Dry Powder/ABC type fire extinguisher.
246	12/20 mm. thick rubber electric resistance rubber sheet as per ISS.
247	Steel revolving high quality chairs
248	Fire bucket with stand as per direction of engineer incharge
249	Steel Almirah of 6’x3'
250	moduler Table & their chairs 6 Nos
251	Installation & Commissioning:
252	Installation & Commissioning of all 6 Nos. pump sets, piping & valves, guide rail, lifting tackle etc. complete in all respect. as per direction of engineer incharge and as per specification of tender documents
253	Painting
254	Provision for painting of all pumps, piping and valves with two coat enamel paint as per direction of engineer incharge
255	Light Wiring
256	Light wiring of Pump House, L.T. control room, Meter room, D.G. room, Store and Staff Quarters with entire required qty of LED lights,fluroescent lights, campus lighting etc.Supply and fixing of 125 watt LED fixture with lamp and its all accessories. complete in all as per direction of EIC
257	Supply & fitting of GI swaged tubular poles of 9M length as per I.E. rules.
258	Supply and laying of 35sq mm Cu conductor XLPE insulated 3.5 core submersible cable from Composite panel to pumps (50 HP) as per specification given in tender documents(paid as per actual basis)
259	Aluminium Junction Box
260	SITC of Exhaust fans of suitable sweep/capacity as per direction of engineer incharge
261	Complete double earthing of all pumping plant with all accessories as earth pipe of size (40 mm dia x 5 mm thick),earth strip of size (50 mm x 6 mm) and required material as per direction of engineer incharge and as per specification given in tender documents
262	Necessory safety equipments such as safety helmet with led head lamp,Yelllow helmet-9 nos,white helmet-4 nos,green helmet-1 no(explosion proof),safety belt with rope-6 nos,protective gloves for Lt Line & Ht Line,fluroscent jacket-9 nos,gas masks and self-contained breathing appratus-2 nos,eye protector-2 nos,air blowers-2 nos ,Electronic Multi Gas Detector,portable alluminum ladder,safety sign board-6 nos,first add box and sewage sump cleaning equipment as per direction of EIC
263	L.T. Pannel
264	2mm thick CRCA sheet fabricated factory wired dust, damp and vermin proof metal clad cubical and floor mounted single row type control panel for system voltage 400+10%, 50 Hz, comprising of following items as follows -Incoming/Outgoing panels L.T. control panel having 4 Nos. (or suitable nos for synchronization) incoming having 400 amp ACB draw out type & outgoing Panels (6 No.) 200 amp microprocesor based mccb , 2 Nos -63 Amp microprocesor based MCCB for aux light & suitable to operated on 400 ± 6 % volt , 3 Phase , 50 Hz, AC supply ,with C.Ts,P.T AVF Meter,KWH meter P.F Meter, Bus Bar chamber, Relays and other Protective Devices Complete in all Respects.Control panel is also suitable to meet the basic requirements of motor protection such as No volt and under voltage protection and thermal over load protection. Panel will be connected with PLC/RTU. Panel will include synchronization systems for Transformer and DG set, Suitable capacity APFC panel for non VFD Laod. as per technical specificatons and mentioned in tender documents direction of EIC
265	Supply and making end termination/joints of the above cable as per direction of engineer incharge
266	Complete double Earthing of panel with GI pipe (40 mm dia x 5 mm thick) & earthing strip of size (50 mm x 6 mm) electrical equipments as per IS/ IER & direction of engineer encharge
267	Proper fencing of sub-station portion with size of angle 50 mm X 50 mm X 5mm and cross support with MS strip 5 mm size thick also as per IE Rules as per direction of engineer incharge and as per technical specifications
268	Charges of Electrical safety clearance.
269	Supply of 5 kg Capacity Dry Powder/ABC type fire extinguisher.as per direction of engineer incharge
270	12/20 mm. thick rubber electric resistance rubber sheet as per ISS.
271	Erection L.T. panels, laying of required cables & filling L.T. Cable end boxes as detailed above.laying of cable should be through channel of brick work and as per direction of engineer in charge
272	Exhaust fans of suitable sweep/capacity including loovers as per direction of engineer incharge
273	Commissioning and testing including type test of the sub station equipment including first filling and centrifuging of oil in the installed equipment wherever necessary.
274	Testing at manufacturer works & site of L.T. Panels
275	Construction of Sub-Station
276	11 KV floor mounting, single row type H.T. panel having 1 No. incoming and 2 Nos. outgoing VCB(630Amp) panels complete with insulated bus bars, all necessary metering and safety equipments.
277	11 KV / 0.400 KV,250 KVA outdoor, step down transformers
278	11 KV XLPE cable of 3 x 150 sqmm size/suitable size Al. armoured cable from meter to HT panel(paid as per actual basis)
279	(D) Supply of 0.44 KV capacitor bank complete with all accessories.
280	(E) Cable Jointing Kit
281	(i) H.T. indoor type
282	(ii) H.T. outgoing type
283	(iii) L.T. indoor type
284	(F) Double earthing of all sub-station equipments complete with salt, charcoal, G.I. earth electrode, C.I. earth boxes, G.I. watering pipe, G.I. earth strip of adequate capacity and should not less than 50mmX 8 mm and required labour &t&p, .as per direction of engineer incharge
285	(I) Supply & fixing of M.S. checkered plate over cable trenches minimum thickness not less than 8 mm as per direction of engineer incharge
286	(J) Miscellaneous work as barbad wire on 50x50x5 mm ms angle ,with bolder fencing of switch yard construction of cable trenches, Safety Equipments i.e Fire Extinguisher ,Sand Bucket ,etc etc.as per direction of engineer incharge
287	(K) Erection and commissioning of all sub-station equipments as per direction of engineer incharge
288	(L) Testing of all equipments of sub-station at manufacturer’s works
289	(L) Construction of foundations of Transformers and panels Hight should be one meter above ground level
290	Manual bar Screen
291	Provision of Stainless Steel(SS 316) manual coarse bar screen having clear gap between screen bar- 50 mm size of flat shall be 50mm x 10mm angle of installation 70º . Complete
292	Mechanical Bar Screen
293	Provision of Stainless Steel (SS 316) mechanical bar screen having clear gap between screen bar- 20 mm, size of SS flat shall be 50 mm x 10 mm, angle of installation - 70º duly suitable for width followed with conveyer system, electric motor, starter, cable, panel, bins etc. (for peak flow upto 20 MLD)
294	Sluice Gate
295	Provision of CI Thimble Mounted Sluice Gate with motor, actuator operated, Rising Spindle type. Sluice gates are as per IS 13349 Including all taxes, Freight, loading, unloading, fitting in position including Sluice gates are upward opening wall thimble mounted suitable for isolating the flow of sewer into out of the opening in the wall. It consists Gate frame, wall thimble, gate slide, shutter, seating/sealing faces .The gates will be provided with pads on sides, top and bottom to mount the wedges. The gate shall be designed in such a manner, so that it can be operated at 2 meter head. Gate frame & Shutter of CI Grade IS 210 FG 260, Head Stock assembly bolts & SS ASTM A276 Type316, Stem, Operating Nut SS ASTM A276 Type 316., Duly tested for tensile strength, Tested for over all dimensions as per approved GA drawing complete in all respect as per specification and direction of Engineer,screen upto size 700x700mm
296	Provision of CI Thimble Mounted Sluice Gate with motor, actuator operated, Rising Spindle type. Sluice gates are as per IS 13349 Including all taxes, Freight, loading, unloading, fitting in position including Sluice gates are upward opening wall thimble mounted suitable for isolating the flow of sewer into out of the opening in the wall. It consists Gate frame, wall thimble, gate slide, shutter, seating/sealing faces .The gates will be provided with pads on sides, top and bottom to mount the wedges. The gate shall be designed in such a manner, so that it can be operated at 2 meter head. Gate frame & Shutter of CI Grade IS 210 FG 260, Head Stock assembly bolts & SS ASTM A276 Type316, Stem, Operating Nut SS ASTM A276 Type 316., Duly tested for tensile strength, Tested for over all dimensions as per approved GA drawing complete in all respect as per specification and direction of Engineer,inlet and bypass and 2 no forsize 1000x1000 at inlet chamber & bypass
297	Testing of above equipment at manufacturer works
298	Installation & Commissioning
299	Installation & commissioning of all screens and sluice gates complete.
300	Diesel Generating sets.
301	Supply of 160 KVA DG Set complete with 1500 RPM Diesel Engine of suitable BHP & AC Brush less SPDP Alternator mounted on a common base Frame & coupled through a flexible coupling or close coupled.Alternator shall be self regulated with standard Alternator Protection( Over voltage , over speed & under voltage). Engine shall have residential silencer, up to 10 M exhaust piping , electronic / Mechanical governor, Manual & electric Start ,Batteries, Fuel tank ( with Stand) & piping , control panel (16 G) with MCCB (4P; 25 KA), Ammeter, Voltmeter, Frequency Meter, Energy Meter & Hour Meter, Engine instruments,accoustic enclosure,Noise level is less than 74 db(A) at a distance of 1 Mtrs, 0.8 pf(lag) 415 V, 3 Ø, 50 Hz capacity with Provision for PLC based AMF Panel fabricated from CRCA sheet steel 2 mm thick, powder coated finish, START & STOP commands, control relays, selector switches for Ammeter and Voltmeter, Ammeter & Voltmeter, Control & Power contactors, timers, electronic hooters, Visual & Alarm indication for faults, UPS, operator interface panel complete in all respect suitable for above DG set,as per technical specifications mentioned in tender documents & direction of EIC
302	Fuel tank as per site requirment.
303	Batteries 24 volt 360AH dry and uncharged with battery leads and battery charger
304	Double earthing of DG set and all electrical equipment as per IIEC rule
305	POWER CABLE/BUS BAR
306	Supplying and laying of Power cable of Suitable size of 415 Volt grade 2R x 150 sqmm 3.5 core armoured XLPE sheathed aluminium conductor from Transformer & DG set to Main LT Panel. (paid as per actual basis)
307	Supply and making end termination/joints of the above cable as per direction of engineer incharge
308	Electric Resistance Rubber sheets.
309	Provision for 12/20mm thick electric resistance rubber sheets as per direction of engineer incharge
310	INSTALLATION, COMMISSIONING AND TESTING
311	Installation, Testing of D.G. set, cable, AMF panel etc.at site as per direction of engineer incharge. HSD and Lubricat oil initially complitly fill by bidder FOC.
312	Commissioning of the above including supply of diesel and oil for trial
313	Testing of D.G set at manufacturer works
314	Automation of SPS-2
315	CE/UL certified local conrol room PLC/RTU with redundant CPU& power supply in IP 54 enclouser to communiate with gsm based modem unit with redundant cpu & power supply with analog and digital parameter and features as per spec mentioned in technical bid documents.
316	GSM/GPRS based wireless communication hardware for RTUs. Capable to transfer data from site to LCS with all accessories etc complete.
317	Intelligent energy meter
318	Smart Pressure transmitter
319	Auto phase reversal unit/Automatic transfer switch with inbuilt time delay and enclosure (Conforming to IEC 60947-1 & IEC 60947-6-1) of suitable for 400 Amp. rating
320	Cabling of all equipments & control cable
321	Security survelliance IP camera
322	Radar type level transmitter with RTU communication
323	Control Panel with IP 65 protection, industrial grade 24 V power supply and other required items
324	3 phase Surge protector for all AC control supplies to all the equipment
325	7\\" HMI touchscreen suitable to communicate with PLC/RTU, for local display & control of process parameters
326	Installation, testing and commissioning
327	(B) transmission line for 11 mld stp plant (payment shall be made as per actual transmission line charges & reimbursed by department)
328	Testing and trial run including manpower,consumable items like HSD,Lube oil (paid as per actual consumption)
329	For SPS-2
330	VFD starter For 20 HP pump set
331	SUBMERSIBLE PUMP SET:
332	Submersible sewage non-clog pumps withJacket cooled Integreated Motor of IP 68Protection for 400±10% V AC, 3phase 50 Hz. suitable to pump raw sewage with specific gravity of 1.05 and also capable to handle solids up to 135mm size with all suitable piping and specials having following material of construction.Casing- 2%NiCIImpeller- ASTM CF8MShaft & Shaft sleeve- ASTM SS 410 included Automatic Coupling system,Guide rail system comprises of Pedestal, bracket, upper guide rail holder,Guide pipe for above 6 sets pumps length upto sumpwell floor level. etc.
333	33 LPS, 20.34 m Head, 980 RPM 20 HP
334	CAPACITOR:
335	Provision for supply of shunt type power factor improvement capacitor of suitable to boost the power factor up to 0.95.
336	MAIN PIPING & VALVES:
337	Provision for main piping and valves for 200 mm dia, and 300 mm dia common header line (sizes can be change as per site condition & requirement)
338	Motor operated Sluice Valve with actuator
339	CIDF300 mm ø
340	CIDF 200 mm ø
341	Reflex Valve
342	CIDF 200 mm ø
343	CIDF 300mm ø
344	Piping
345	DIDF Pipe dia 300 mmX 3 m
346	DIDF Pipe dia 200 mm X 3M
347	CIDF Tee 300x200x300 mm,DI blind flange dia 300 mm, bend dia 300 mm,200 mm dia,duckfoot bend dia 200 mm,CIDF Reducer/Enlarger 300 mmx200 mm ,Reducer/Enlarger 150 mmx 200 mm as per requirement of site & direction of EIC
348	Dismenaling joints 200 mm
349	Dismenaling joints 300 mm
350	Nut and bolts with washer(SS) M20x120,(SS) M24x120,(SS) M27x140
351	Necessary Piping pump set foundation rubber packing, insertion and other material
352	Electromagnetic Flow Meter:
353	(i) Providing, Installation, Testing and commissioning of 300 mm ELECTRO MAGNETIC FLOW METER cum totalizer having following charecteristics/MOC: Liner: Polyurethane or Hard Rubber / Electrode MOC: SS316L /Housing : Die Cast Aluminium or CS / Power Supply: 90-230 V AC / Output: 4-20mA with HART / Sensor Cable : 10 mt / Flow Tube or Sensor housing protection IP68 / Process Flange : SS316 / Display : 3 1/2 LCD Display / Cable Connection : 1/2\\"NPT /Accuracy : 0.5%
354	(ii) CVT with control cables
355	LIFTING TACKLE:
356	Supply, installation and commissioning of 3 T Mono Rail Single Girder having suitable lift with chain, pulley block and traveling trolley complete
357	Tools & Plants as per mentioned in tender documents and direction of engineer incharge
358	Supply of 5 kg Capacity Dry Powder/ABC type fire extinguisher.
359	12/20 mm. thick rubber electric resistance rubber sheet as per ISS.
360	Steel chairs.
361	Fire bucket with stand
362	Steel Almirah of 6’x3’
363	Steel Tubular Table
364	Installation & Commissioning:
365	Installation & Commissioning of all 6 Nos. pump sets, piping & valves, guide rail, lifting tackle etc. complete.
366	Painting
367	Provision for painting of all pumps, piping and valves with two coat enamel paint as per direction of engineer incharge.
368	Light Wiring
369	Light wiring of Pump House, L.T. control room, Meter room, D.G. room, Store and Staff Quarters with entire required qty of LED lights,fluroescent lights, campus lighting etc.Supply and fixing of 125 watt LED fixture with lamp and its all accessories. complete in all as per direction of EIC
370	Supply & fitting of steel swaged tubular poles of 9M length as per I.E. rules.
371	Supply and laying of 10 sq mm Cu conductor XLPE insulated 3.5 core submersible cable from Composite panel to pumps (20 HP) (paid as per actual basis)
372	Aluminium Junction Box as per direction of engineer incharge.
373	SITC of Exhaust fans of suitable sweep/capacity with loovers as per direction of engineer incharge
374	Complete double earthing of all pumping plant with all accessories as earth pipe of size (40 mm dia x 5 mm thick),earth strip of size (50 mm x 6 mm) and required material as per direction of engineer incharge and as per specification given in tender documents
375	Necessory safety equipments such as safety helmet with led head lamp,Yelllow helmet-7 nos,white helmet-3 nos,green helmet-1 no(explosion proof),safety belt with rope-4 nos,protective gloves for Lt Line & Ht Line,fluroscent jacket-6 nos,gas masks and self-contained breathing appratus-2 nos,eye protector-2 nos,air blowers-2 Nos,Electronic Multi Gas Detector,portable alluminum ladder,safety sign board-6 nos,first add box and sewage sump cleaning equipment as per direction of EIC
376	L.T. Pannel
377	2mm thick CRCA sheet fabricated factory wired dust, damp and vermin proof metal clad cubical and floor mounted single row type control panel for system voltage 400+10%, 50 Hz, comprising of following items
378	Incoming/Outgoing panels
379	L.T. control panel having 4 Nos. (or suitable nos for synchronization) incoming having 250 amp MCCB draw out type & outgoing Panels (6 No.) 100 amp microprocesor based mccb , 2 Nos -63 Amp microprocesor based MCCB for aux light & suitable to operated on 400 ± 6 % volt , 3 Phase , 50 Hz, AC supply ,with C.Ts,P.T AVF Meter,KWH meter P.F Meter, Bus Bar chamber, Relays and other Protective Devices Complete in all Respects.Control panel is also suitable to meet the basic requirements of motor protection such as No volt and under voltage protection and thermal over load protection. Panel will be connected with PLC/RTU. Panel will include synchronization systems for Transformer and DG set, Suitable capacity APFC panel for non VFD Laod with all protection & techncial specification mentiond in tender doc.& direction of EIC
380	Supply and making end termination/joints of the above cable
381	Supply and making end termination of the above cable
382	Complete double Earthing of panel with GI pipe (40 mm dia x 5 mm thick) & earthing strip of size (50 mm x 6 mm) electrical equipments as per IS/ IER & direction of engineer encharge
383	Proper fencing of sub-station portion with size of angle 50 mm X 50 mm X 5mm and cross support with MS strip 5 mm size thick also as per IE Rules as per direction of engineer incharge and as per technical specifications
384	Charges of Electrical safety clearance.
385	Supply of 5 kg Capacity Dry Powder/ABC type fire extinguisher.as per direction of engineer incharge
386	12/20 mm. thick rubber electric resistance rubber sheet as per ISS.
387	Erection L.T. panels, laying of required cables & filling L.T. Cable end boxes as detailed above.laying of cable should be through channel of brick work and as per direction of engineer in charge
388	Exhaust fans of suitable sweep/capacity
389	Commissioning and testing including type test of the sub station equipment including first filling and centrifuging of oil in the installed equipment wherever necessary.
390	Testing at manufacturer works L.T. Panels
391	Construction of Sub-Station
392	(A) 11 KV floor mounting, single row type H.T. panel having 1 No. incoming and 2 Nos. outgoing VCB(630Amp) panels complete with insulated bus bars, all necessary metering and safety equipments.
393	(B) 11 KV / 0.400 KV,125 KVA outdoor, step down transformers
394	(C) 11 KV XLPE cable of 3 c x70 sqmm/suitable size Al. armoured cable from Meter To HT Panel & HT panel To transformer (paid as per actual basis)
395	Supply of 0.44 KV capacitor bank complee with all accessories.
396	(E) Cable Jointing Kit
397	(i) H.T. indoor type
398	(ii) H.T. outgoing type
399	(iii) L.T. indoor type
400	Double earthing of all sub-station equipments complete with salt, charcoal, G.I. earth electrode, C.I. earth boxes, G.I. watering pipe, G.I. earth strip of adequate capacity and should not less than 50mmX 8 mm and required labour &t&p, .as per direction of engineer incharge
401	(I) Supply & fixing of M.S. checkered plate over cable trenches
402	Miscllenous work as barbad wire fencing of switch yard construction of cable trenches, Safety Equipments i.e Fire Extinguisher ,Sand Bucket ,etc etc.
403	Erection and commissioning of all sub-station equipments
404	Testing of all equipments of sub-station at manufacturer’s works
405	Construction of foundations of Transformers and panels
406	Manual bar Screen
407	Provision of Stainless Steel(SS 316) manual coarse bar screen having clear gap between screen bar- 50 mm, size of flat shall be 50mm x 10mm angle of installation 70º . Complete
408	Mechanical Bar Screen
409	Provision of Stainless Steel (SS 316) mechanical finebar screen having clear gap between screen bar- 6 mm, size of SS flat shall be 50 mm x 10 mm, angle of installation - 70º duly suitable for 2.44 m wide followed with conveyer system, electric motor, starter, cable, panel, bins etc. (for peak flow upto 10MLD)
410	Sluice Gate
411	Provision of CI Thimble Mounted Sluice Gate with motor, actuator operated, Rising Spindle type. Sluice gates are as per IS 13349 Including all taxes, Freight, loading, unloading, fitting in position including Sluice gates are upward opening wall thimble mounted suitable for isolating the flow of sewer into out of the opening in the wall. It consists Gate frame, wall thimble, gate slide, shutter, seating/sealing faces .The gates will be provided with pads on sides, top and bottom to mount the wedges. The gate shall be designed in such a manner, so that it can be operated at 2 meter head. Gate frame & Shutter of CI Grade IS 210 FG 260, Head Stock assembly bolts & SS ASTM A276 Type316, Stem, Operating Nut SS ASTM A276 Type 316., Duly tested for tensile strength, Tested for over all dimensions as per approved GA drawing complete in all respect as per specification and direction of Engineer
412	Testing of above equipment at manufacturer works
413	Installation & Commissioning
414	Installation & commissioning of all screens and sluice gates complete.
415	Diesel Generating sets.
416	Supply of 82.5 KVA DG Set complete with 1500 RPM Diesel Engine of suitable BHP & AC Brush less SPDP Alternator mounted on a common base Frame & coupled through a flexible coupling or close coupled.Alternator shall be self regulated with standard Alternator Protection( Over voltage , over speed & under voltage). Engine shall have residential silencer, up to 10 M exhaust piping , electronic / Mechanical governor, Manual & electric Start ,Batteries, Fuel tank ( with Stand) & piping , control panel (16 G) with MCCB (4P; 25 KA), Ammeter, Voltmeter, Frequency Meter, Energy Meter & Hour Meter, Engine instruments,accoustic enclosure,Noise level is less than 74 db(A) at a distance of 1 Mtrs, 0.8 pf(lag) 415 V, 3 Ø, 50 Hz capacity with Provision for PLC based AMF Panel fabricated from CRCA sheet steel 2 mm thick, powder coated finish, START & STOP commands, control relays, selector switches for Ammeter and Voltmeter, Ammeter & Voltmeter, Control & Power contactors, timers, electronic hooters, Visual & Alarm indication for faults, UPS, operator interface panel complete in all respect suitable for above DG set,as per technical specifications mentioned in tender documents & direction of EIC
417	Fuel tank
418	Batteries 24 volt 360AH dry and uncharged with battery leads and battery charger
419	Double earthing of DG set and all electrical equipment as per IS
420	Supplying and laying of Power cable of Suitable size of 415 Volt grade 3.5 core 95 sq.mm/suitable size AL armoured XLPE sheathed aluminium conductor from Transformer,DG set panel to LT panel (paid as per actual basis)
421	Supply and making end termination/joints of the above cable
422	Provision for 12/20mm thick electric resistance rubber sheets
423	INSTALLATION, COMMISSIONING AND TESTING
424	Installation, Testing of D.G. set, cable, AMF panel etc.at site
425	Commissioning of the above including supply of diesel and oil for trial
426	Testing of D.G set at manufacturer works
427	CE/UL certified local conrol room PLC/RTU with redundant CPU& power supply in IP 54 enclouser to communiate with gsm based modem unit with redundant cpu & power supply with analog and digital parameter and features as per spec mentioned in technical bid documents.
428	GSM/GPRS based wireless communication hardware for RTUs. Capable to transfer data from site to LCS with all accessories etc complete.
429	Intelligent energy meter
430	Smart Pressure transmitter
431	Auto phase reversal unit/Automatic transfer switch with inbuilt time delay and enclosure (Conforming to IEC 60947-1 & IEC 60947-6-1) of suitable for 4000Amp. rating
432	control Cabling and cabling of all equipments installed in PS
433	Security survelliance IP camera
434	Radar type level transmitter with RTU communication
435	Control Panel with IP 65 protection, industrial grade 24 V power supply and other required items
436	3 phase Surge protector for all AC control supplies to all the equipment
437	7\\" HMI touchscreen suitable to communicate with PLC/RTU, for local display & control of process parameters
438	Installation, testing and commissioning
439	CE & BIS approved manufacturer's industrial grade 65 inch LCD monitor with latest configuration as per specification of size 65\\"
440	Desktop/PC i7 for LCS as per spec. mentioned in tender doc
441	CE/UL approved manufacturer's 3 KVA UPS with batteries as spec. mentioned for LCS and Computer as per requirement
442	Full development version of required TAGS SCADA software suitable for digital and analog input/output features with customization of software as per requirement as per spec. mentioned with unlimited digital and analog Input/Output features specified in detailed technical document with customization of software as requirement
443	CE & UL approved manufacturer's control room PLC with CPU & power supply at LCS in IP65 enclosure as per spec. mentioned
444	GSM based wireless communication system for PLC capable to transfer and gather data from remote sites to control stations, including all accessories complete
445	CE/UL approved manufacturer's Firewall for network protection
446	Lightning surge protector for ethernet communication protection
447	CE/UL approved manufacturer's industrial grade ethernet switch
448	Canon/HP 1018/equivalent Laser printer(1 Color & 1 Black & white)
449	Security Survelliance IP camera for LCS
450	Installation, testing and commissioning
451	Test and trial run including manpower,consumable items like HSD,Lube oil (paid as per actual consumption) Please Enable Macros to View BoQ information

Tender Documents

SR No	FileName	File Description
1	Click here to download tender document	Tender Documents
2	Click here to download tender document	Tender Documents
3	Click here to download tender document	Tender Documents
4	Click here to download tender document	Tender Documents

Also Visit

Tenders

Uttar Pradesh Tenders

Construction Tenders

Drainage Work Tenders

Sewerage Construction Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Providing Of Sewer Network And House Connection Work In Ramnagar Zone (Extended Area) Of Nagar Nigam Varanasi, Distt-Varanasi, Ramnagar-Uttar Pradesh

Tender Documents

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Providing Of Sewer Network And House Connection Work In Ramnagar Zone (Extended Area) Of Nagar Nigam Varanasi, Distt-Varanasi, Ramnagar-Uttar Pradesh

Tender Documents

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us