|
| 1 | MANDATORY SPARES FOR MECHANISM & POLE OVERHAULING OF 145KV SF-6 GAS CIRCUIT BREAKER, Type - 120 SFM 32B (Qty.-01 no.) ( from Sl no. 01-39)MOTOR 230V AC/DC(TYPE C-22) |
| 2 | LIMIT SWITCH (1 NO + 1 NC) |
| 3 | MOTOR CONTACTOR 110V /220DC (WITH ADD ON BLOCK) |
| 4 | CLOSE/TRIP COIL 110V/220V |
| 5 | CLOSING HOLDING LATCH |
| 6 | RATCHET WHEEL ASSLY WITH BLACK BOLT , STOP ROLLER, BEARING & BAR PIN |
| 7 | CLOSING TRIGGER WITH BEARING |
| 8 | TRIPPING TRIGGER WITH BEARING |
| 9 | SMALL PAWL WITH BEARING |
| 10 | LARGE PAWL WITH BEARING |
| 11 | ECCENTRIC SHAFT BEARING (4906) FRONT |
| 12 | ECCENTRIC SHAFT BEARING ( 4904) REAR |
| 13 | THRUST BEARING 4060 FOR BLACK BOLT |
| 14 | THRUST WASHER FOR BLACK BOLT (THIN) |
| 15 | THRUST WASHER FOR BLACK BOLT (THICK) |
| 16 | BEARING FOR CLOSING SPRING ROD |
| 17 | BUSH FOR CLOSING SPRING ROD |
| 18 | BRASS WASHER FOR BLACK BOLT |
| 19 | O-RING P12 |
| 20 | BERUTOX GREASE ( 100gm) |
| 21 | LOCKTITE (01 PKT-20ML) |
| 22 | CATCH SPRING |
| 23 | TORSION SPRING (RIGHT & LEFT) |
| 24 | MUSLIN CLOTH |
| 25 | 3 BOND COMPOUND ( 1 Pkt -10 Gms)/ MOLYKOTE GREASE 111/EQ |
| 26 | SET OF CIRCLIP, GRUB SCREW, SPLIT PINS ETC |
| 27 | CHEMISTIC |
| 28 | EMERY PAD |
| 29 | SPACE HEATER 240VAC/250W |
| 30 | ETNA SEAL SET |
| 31 | O-RING P-105 |
| 32 | O-RING G-240/G-220 |
| 33 | ABSORBENT |
| 34 | MICRO CARBON GREASE (50 GRAMS) |
| 35 | ANABOND 680 /SILASTIC 1080 (100 GRAMS) |
| 36 | JOINTAL - Z (1 Pkt = 10 Gms) |
| 37 | 3 NO + 2 NC CONTACTOR 110 V DC |
| 38 | VACUUM PUMP |
| 39 | Service charges of Engineer for overhauling of circuit breaker |
| 40 | MANDATORY SPARES FOR MECHANISM & POLE OVERHAULING OF 145KV SF-6 GAS CIRCUIT BREAKER, Type - 120 SFM 32 A (Qty.-04 nos.) ( from Sl no.40-90)O ring P - 18 |
| 41 | O ring P - 7 |
| 42 | Control valve seat |
| 43 | Roller with Bearing for Holding latch |
| 44 | Muslin cloth |
| 45 | 3 bond compound ( 1 Pkt -10 Gms )/MOLYKOTE GREASE 111 |
| 46 | Anabond 680 (100 Gm)/SILASTIC 1080 |
| 47 | Reservior Oring |
| 48 | Al. pipe O ring IAP - 80 |
| 49 | Set of circlips, split pins,Grub screws, Allen Bolts. |
| 50 | Darina Grease ( 1 pkt - 500 Gms ) |
| 51 | Safety valve |
| 52 | Trip latch spring |
| 53 | Manual Trip cord assembly |
| 54 | Antipumping spring |
| 55 | Bearing of holding latch barpin ( Mechframe) |
| 56 | C/D roller with bearing |
| 57 | Capseal with O-ring |
| 58 | Shockproof rubber with hardwares |
| 59 | Chemistic |
| 60 | Emery Pads ( Scrotch Brite) |
| 61 | Filter pads for louvers |
| 62 | Blind caps for stop valve |
| 63 | Compressor tuneup kit (145kv) |
| 64 | Trip Latch |
| 65 | 7No/2Nc 110VDC Contactor |
| 66 | 5No/4Nc 110VDC Contactor |
| 67 | Nyloc nut of Control valve drive rod |
| 68 | Bearings of the Barpin where holding latch gets latched |
| 69 | Oring IAP44 |
| 70 | Oring IAP90 |
| 71 | contral valve drive rod |
| 72 | NRV(Check Valve) |
| 73 | Drain valve |
| 74 | Shock absorber oil |
| 75 | Tripping Coil 110/220VDC |
| 76 | Closing Coil 110/220VDC |
| 77 | O Ring P -195 |
| 78 | O Ring G -185 |
| 79 | O Ring P -170 |
| 80 | O Ring P - 32 |
| 81 | O Ring G -170 |
| 82 | Jointal Z (10gms) |
| 83 | Etna Seal set |
| 84 | Absorbent |
| 85 | Micro Carbon Grease ( 1 pkt - 50Gms) |
| 86 | Anabond 680/silastic1080 ( 100 Gm ) |
| 87 | 3 NO + 2 NC Contactor 110 V DC |
| 88 | SF6 Gas 25 KG |
| 89 | Comprssor Motor |
| 90 | Service charges of Engineer for overhauling of circuit breaker |
| 91 | Total impact of GST for the purpose of CTC Please Enable Macros to View BoQ information |
