|
| 1 | Removal of old chocked filter media (sand & gravel) manually by scrapping and removing layer wise with the help of rope and buckets carefully to ensure separation of the different grades / guages and stacking / dumping within an average lead of 100Mtrs. as directed by Engineer In-charge. Complete Job. |
| 2 | Washing / cleaning / seiving of filter media of all grades getting free from all dirt, clay, dust etc. The job includes stacking of serviceable cleaned filter media and to separate the different sizes for use in layers (measurements to be taken in finished form). |
| 3 | Providing, laying and placing in position, filter media i.e. (Natural gravel of size 25mm to 2mm spherical as much as possible to be arranged in three layers of 200mm each as a graded material with coarse layer at bottom and fine at top in the range of 25mm-12mm, 12mm -6mm and 6mm -2mm) in filter beds, properly graded, duly cleaned, washed and placed above and surrounding PVC under drainage pipes without causing any damage to these pipes including all carriages, leads lifts etc. up to site of consumption. The filter media shall conform to relevant IS: specification / referred to IS:8419 (Part-I) 1977 read with latest amendments. (Complete Job) including all carriages whatsoever involved. |
| 4 | Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres: i. All kinds of soil : |
| 5 | i. Ordinary Rock |
| 6 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m. |
| 7 | General servicing and annual maintenance of 40HP Air Blower and Motor Assembly with dry starter by way of dismantling Dismembering and carrying to appropriate workshop for repairs, overhauling, replacement of worn out / damaged parts in Air Blower and motor, carrying back to site of work, after completion of overhauling to the best satisfaction of the Engineer-in-Charge, reassembling and re-fixing at its original position including replacement of M.Oil of suitable grade, air filter polyester fan belts corresponding to IS specification, replacement of worn out nuts and botls by SS anti-corrosive nuts and bolts, greasing of parts including repairs to electrical control boxes, making of required electrical and mechanical connections, including painting of surfaces with two coats of primer and metal paint of approved quality to give an even shade. The job includes all labour, T&P charges, taxes etc. whatever required as directed by Engineer-in Charge. |
| 8 | General servicing / overhauling of 20HP vertical submersible back wash pumping unit assembly with dry starter by way of dismantling / dismembering and carrying to appropriate workshop for repairs, overhauling, replacement of worn out / damaged parts in back wash pump and motor, carrying back to site of work, after completion of overhauling to the best satisfaction of the Engineer-in-Charge, reassembling and refixing at its original position including replacement of M.Oil of suitable air filter polyester fan belts corresponding to specification, replacement of worn out nuts and bolts by S.S anti-corrosive nuts and bolts, greasing of parts including repairs to electrical control boxes, making of required electrical and mechanical connections, including painting of surfaces with two coats of primer and metal paint of approved quality to give an even shade. The job includes all labour, T&P charges, taxes, etc. complete job. |
| 9 | Providing and installation of different types of MCCB / MCB. The job includes making of electrical connections and should be Havels / Anchor / GM Make.i. 400Amp MCCB |
| 10 | ii. 250Amp MCCB |
| 11 | iii. 100Amp MCCB |
| 12 | iv. 63Amp MCCB |
| 13 | v. 32Amp MCCB |
| 14 | vi. 16Amp MCB |
| 15 | vii. 20Amp 2 Pole MCB |
| 16 | viii. 10Amp 2 Pole MCB |
| 17 | ix. 63Amp 2 Pole MCB |
| 18 | x. 63Amp 4 Pole MCB |
| 19 | xi. Single Phase Preventor |
| 20 | XiiSuitable feeder panel with cable alley. |
| 21 | ii. 150A 4P MCCB 36kA |
| 22 | iii. 6A 1P 10kA C-Curve MCB |
| 23 | iv. LED indicator 22.5 mm 240V (Red) |
| 24 | v. LED indicator 22.5 mm 240V (Yellow) |
| 25 | vi. LED indicator 22.5 mm 240V (Blue) |
| 26 | vii. Aluminium bus bar |
| 27 | viii. 50 sq.mm terminal block |
| 28 | ix. 16 sq.mm terminal block |
| 29 | x. End plate for TB |
| 30 | xxii. Energy saver lamps 9w |
| 31 | ii. Energy saver lamps 12w |
| 32 | iii. Energy saver lamps 25w |
| 33 | iv. Rechargable Torch / light |
| 34 | v. concealed lamp 7/9/12Watt |
| 35 | vi. 50w led flood light |
| 36 | vii. 45w street light |
| 37 | viii. 1.5 mm electric wire |
| 38 | ix. 2mm Electric |
| 39 | x. 2.5mm Electric Wire |
| 40 | xi. Three Core 25mm Dia Wire |
| 41 | xii. Two Core 16mm Dia Wire |
| 42 | xiii. 3.5 Core Wire 25mm2 Armored Cable |
| 43 | xiv. 3.5 Core Wire 50mm2 Armored Cable |
| 44 | xv. 20000 lumens rechargable torch |
| 45 | xvi. 25mm*2 core aluminium cable |
| 46 | xvii. 16mm*2 core aluminium cable |
| 47 | xviii. 10mm*2 core aluminium cable |
| 48 | xix. 2.5mm*2 core copper cable |
| 49 | xx. 4mm*2 core copper cable |
| 50 | xxi. 6mm*2 core copper cable |
| 51 | xxii. 7/16 core copper cable |
| 52 | xxiii. 10 A one way switch |
| 53 | xxiv. 6 A 3 pin socket |
| 54 | ii. 20 A switch |
| 55 | iii. 16A socket |
| 56 | iv. Indicator |
| 57 | v. fan dimmer |
| 58 | vi. black plate |
| 59 | vii. 12 module plate |
| 60 | lii. 8 module plate |
| 61 | Annual repairs to SERVO CAPACITY 3 phase 150KVA input Voltage Stablizers with replacement of its damaged coils, top leveling transformer oil and the replacement of voltmeters amphere-meters. The job includes dismembering refitting of the same after repairs as per the direction of the Engineer-in-Charge as a fraction of rate to be paid as per actual at site. |
| 62 | Dismembering/refitting of sluice valves of different diameters varying from 150mm to 450mm dia by way of removing / cutting damaged corroded rusted nuts with the help of hacksaw blades/ spindle rod/Check nuts and refitting the same after rethreading of rods with check nuts wherever required . the job also includes servicing , greasing , oiling , after cleaning with kerosene oil including cost of lubricants and approved mark, kerosene oil, bolts, washers and gland packing complete job.i. 150mm / 200mm dia. |
| 63 | ii. 300mm / 350mm dia. |
| 64 | iii. 450mm / 500mm dia |
| 65 | iv. 600mm dia |
| 66 | Providing and fixing MS rods for operating of various kinds of sluice valves of different diameter to be hammered on one side so as to fit into directly hand wheel and other side should be filled with welding to MS rod worth cavity/ cup to be as per square diametric of sluice rod. The hand rail and coupling should be fitted with stainless steel cut pins after making proper hole in wheel and rods. The job includes all carriage taxes upto the actual site of work. |
| 67 | Repairs to reduction Gear Assembly of Churners by way of Repair / re-toothing of gears, servicing well. Replacement of gear oil and as per requirement at site. The job includes oiling, greasing of reduction gears, after proper screening and inclusion of all accessories to be explained if needed during the servicing operation. for ensuring complete and smooth functioning of the unit. The job includes all carriages, taxes and leavis complete work.i. Clarifloculator |
| 68 | ii. Bleaching Tank |
| 69 | Day to day maintenance work of Top Station.i. Rubber washers for regulating valves. |
| 70 | ii. Cleaning aids( cleaning wipers) |
| 71 | iii. Bucket 10 lt (samrudhi or equivalent) |
| 72 | iv. Dustpan (samrudhi or equivalent) |
| 73 | v. Mug 1lt (samrudhi or equivalent) |
| 74 | vi. Dhoti cloth |
| 75 | vii. Duster cloth |
| 76 | viii. Floating material arrester( with steel net) complete. |
| 77 | ix. Bamboo sticks 10feet length of specified dia to suite the handling requirement while cleaning the tanks /floculators. |
| 78 | i. Wooden Hand Cart |
| 79 | ii. Plastic chappals. |
| 80 | iii. Slippers clog type |
| 81 | iv. Hand brushes |
| 82 | v. Brushes with handle |
| 83 | vi. Algea brush with stainless steel bristles with handle |
| 84 | i. Lubricating Oil |
| 85 | ii. Grease |
| 86 | iii. Gear oil |
| 87 | iv. stainless steel cotter pins (100/ 150/200mm long). |
| 88 | v. Appreciation certificate ( coloured on A4 sheet) |
| 89 | vi. R.I cloth |
| 90 | i. Wooden cushion chair |
| 91 | ii. Manual hockey stick grass cutter |
| 92 | iii. Hand saw |
| 93 | iv. Plant cutter |
| 94 | v. Gas and electric heater (4.2k watt ) |
| 95 | xxvii. Set of adjustable wrenc 8 inch , pipe wrench 10 inch ,water pump plier 10 inch |
| 96 | i. Spanner set (12 pcs) |
| 97 | ii. Screw Driver Set |
| 98 | iii. MS Winch Type Controlling Gates for distribution boxes & clarifloculator. |
| 99 | iv. Grease Gun |
| 100 | v. Rubber Coupling for 40HP Pumps |
| 101 | vi. Link set for main transformer |
| 102 | vii. Bosch Rod for Mian Transformer |
| 103 | viii. Thimble different sizes |
| 104 | ix. Trasnformer Oil |
| 105 | x. Fan Belt of Various sizes |
| 106 | xi. Short gum boots |
| 107 | xii. Winter Long Gum Boots |
| 108 | i. Lab coat apron |
| 109 | ii. Safety halmet |
| 110 | iii. Water saftey jacket |
| 111 | iv. Battery acid |
| 112 | v. Reparing of Inverter with Battery |
| 113 | vi. Ring spanner set |
| 114 | vii. Plate spanner set |
| 115 | viii. Hammer |
| 116 | ix. Picaxe |
| 117 | x. Axe |
| 118 | xi. Cleaning spade or rack or hand weeder |
| 119 | xii. Showel |
| 120 | xiii. Steel Jumper |
| 121 | xiv. Plier |
| 122 | xv. 150KVA Stabliser bosch rod |
| 123 | xvi. Starter panel timer |
| 124 | xvii. Bolts/Nuts different sizes |
| 125 | lvii. Esquire trofi plastic table 4 seater, cane matte surface having dimensions 114.5D X 74 W X 74H centimeters, rectangular as per engineer incharge. |
| 126 | lviii. Gauge books , testing report books / log books having dimensions 20cm x 30cm, including 100 leafs , including proper binding and printing as per engineer incharge all complete job. |
| 127 | lix. Pressure Cooker 5 litre Hawkins or equivalent brand. |
| 128 | lx. Pressure Rice Cooker 3 litre Hawkins or equivalent brand. |
| 129 | lxi. Rice Cooker 5 litre Panasonic or equivalent brand |
| 130 | lxii. Commercial Cooking Gas Cylinder including carriage Complete Job. |
| 131 | lxiii. Cooking Utensils full set viz Cooking Pot (2No), Frying Pan, Wok, Knife, Cups(6), Skimmer, Vegetable Peeler ,Slotted Spoon, Metal Spoon ,Wooden Spoon. |
| 132 | i. Gas Stove Double. |
| 133 | ii. Room Matting with Thermocol. |
| 134 | iii. Rubber Sheet. |
| 135 | iv. Fire extinguisher |
| 136 | v. Providing and fixing of Running V Belt for Air Blower. |
| 137 | vi. Colured Printer Three in One. |
| 138 | vii. Ink for Printer Colured (black only). |
| 139 | viii. Ink for Printer Colured (All Four). |
| 140 | ix. Black Toner for Printer. |
| 141 | x. Curtains 7'x5' with rods complete Job. |
| 142 | xi. Tarpulain |
| 143 | xii. Paper Rim A4. |
| 144 | xiii. Attendance Register. |
| 145 | xiv. Long Notebooks. |
| 146 | xv. Rubber Pipe 25mm. |
| 147 | xvi. Cleaning Towel. |
| 148 | xvii. Towel (medium) |
| 149 | xviii. Towel (large) |
| 150 | xix. Harpic. |
| 151 | xx. Colin |
| 152 | xxi. Soap |
| 153 | xxii. Gas regulator. |
| 154 | xxiii. Gas pipe. |
| 155 | xxiv. Wire Mesh Stainless steel. |
| 156 | xxv. PVC Flooring. |
| 157 | xxvi. Wall fan. |
| 158 | xxvii. Table fan. |
| 159 | xxviii. Ceiling fan. |
| 160 | xxix. Blower for heating. |
| 161 | xxx. Blankets. |
| 162 | xxxi. Inverter Battery. |
| 163 | i. PPR Pipe 25mm Dia with fittings. |
| 164 | ii. Pillow. |
| 165 | iii. Sanitiser (100ml) |
| 166 | iv. Bathroom refreshner. |
| 167 | v. Liquid Handwash. |
| 168 | vi. Pressure Gauge. |
| 169 | vii. Rain Coats. |
| 170 | viii. Water proof uniform |
| 171 | ix. ph meter. |
| 172 | x. TDS Meter |
| 173 | xi. float ball valve |
| 174 | xii. Water level sensor |
| 175 | xiii. Lutron TU 2016 turbidity meter |
| 176 | xiv. JAR test apparatus as per is code |
| 177 | xv. HSD for Generator |
| 178 | xvi. Water gyser 50ltrs capacity with all fittings of Standarmake |
| 179 | i. Refregirator 50Ltr with Automatic Stabliser |
| 180 | ii. Hire Charges of Water Proof Tent |
| 181 | iii. Quilt & Matress (Two Person) |
| 182 | iv. Blanket Double Bed |
| 183 | v. Pillow |
| 184 | vi. Bamboo ladder |
| 185 | vii. Aluminium ladder |
| 186 | viii. Wire gaze wooden sieve |
| 187 | ix. Umbrella |
| 188 | x. Plastic unbreakable office chair |
| 189 | xi. 4module plate |
| 190 | xii. Metal office wardrobe/2 door almirah |
| 191 | xiii. 8mp cctv camera complete job |
| 192 | xiv. 16 way mcb box |
| 193 | i. providing and fixing of steel window hook |
| 194 | ii. exhaust fan |
| 195 | iii. automatic shoe cover dispenser with 100 pcs |
| 196 | iv. shoe cover for automatic shoe cover machine 100 pcs |
| 197 | v. shoe rack ( 4 /5shelves ) |
| 198 | vi. bosch or equivalent gbh 220 corded rotary hammer |
| 199 | cxxxi. bosch or equivalent gbh 900-100 heavy duty electric angle grinder |
| 200 | cxxxii. pipe insulation foam 6ft long. |
| 201 | cxxxiii. Smart wood Centre Table with plain glass top(120cmx60x40). |
| 202 | Setting right of current arresters (Slippering System) of Clarifloculators. The job includes dismantling and refitting of the same at its original position after getting repairs including all carriages, taxes and leavis complete work. |
| 203 | Supply of labours. i. Skilled |
| 204 | i. Unskilled |
| 205 | ii. Motor Mechanic |
| 206 | iii. Electrician |
| 207 | iv. Carpenter |
| 208 | v. Mason |
| 209 | vi. Chowkidar |
| 210 | vii. CCTV Technician |
| 211 | V.Pruner |
| 212 | providing , fixing & installation of monkey hoist mini crane single phase at for lifting of alum at top station with following details i.Lifting Height 30 m ii.Channel And Chassis Size 75x40x40mm heavy duty iii. Surface Finish Paint coated iv. Prime Mover 3HP Crompton greavs v. Jib Working 10mm Usha martenvi. Cross Angle 35x35x5mm vii. Operated System Bentex starter-R/F or remote controlix. Gearbox: 3 x. Capacity: 300-500 Kg |
| 213 | Providing, fixing of M.S flanges by welding including cost of cutting making both holes made out of 10mm thick M.S plate to the pipes of different dia’s and including cost of nuts, bolts, washers etc. (Complete Job). (Subject to actual quantities during execution).i. 200mm dia |
| 214 | ii. 150mm dia |
| 215 | Providing, fixing of M.S fittings viz bends of suitable degrees / size to be fabricated out of 8mm to 10mm thick MS. plate as per the requirement of site. This item includes cost of lead, spun yarn, R.I. cloth and lead caulking, lead beating with insertion of spun yarn etc. The fittings should be leak proof and should be painted with Anticorrosive Red Oxide Primer and incld. all carriages, leads lifts, etc. complete. (Subject to actual quantities during execution). |
| 216 | Supply of lead, spun Yarn, Fire Wood Kerosene including all carriages upto site of work.i. Lead |
| 217 | i. Spun Yarn |
| 218 | ii. Fire Wood |
| 219 | Kerosene |
| 220 | work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. i. Welded |
| 221 | Providing fixing of Sluice Valves / Regulatory Valve including cost of Flanged joints/Pipe Specials necessary including cost of nuts, bolts & washers complete Job.Zoloto/Kirloskar or any equivalent make.i. 200mm dia |
| 222 | ii. 150mm dia |
| 223 | Engagement of Hydraulic excavator with driver and fuel Including haltage. complete job. |
| 224 | Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. |
| 225 | Finishing walls with water proofing cement paint of required shade: i. Old work (one or more coats applied @ 2.20 kg/10sqm) over priming coat of primer applied @ 0.80 liters/10sqm complete including cost of priming coat. |
| 226 | Servicing/maintenance of pumps / motors by way of providing coupling ,washers, includings testing, commissioning all carriages, handling, re-handling , oiling, greasing, change of oil etc. all complete job.i. 2 HP motors of churners of clarifloculator. |
| 227 | i. 5 HP motors of clarifloculator. |
| 228 | ii. 2 HP motors of booster pumps. |
| 229 | III. 40HP Back wash pumps |
| 230 | Demolishing cement concrete manually/by mechanical means including disposal of material within 50 meters lead as per direction of Engineer-incharge: i. 1:3:6 or richer mix (i/c equivalent design mix) |
| 231 | ii. 1:4:8 or leaner mix (i/c equivalent design mix) |
| 232 | Demolishing R.C.C. work manually/by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge. |
| 233 | Extra for cutting reinforcement bars manually/by mechanical means in R.C.C. or R.B. work (Payment shall be made on the cross sectional areas of R.C.C. or R.B. work) as per direction of Engineer-in-charge. |
| 234 | Extra for scrapping, cleaning and straightening reinforcement from R.C.C. or R.B. work. |
| 235 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level withi. 1:1½:3 (1 cement :1½ coarse sand: 3 graded stone aggregate 20 mm nominal size) |
| 236 | ii. 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) |
| 237 | iii. 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). |
| 238 | iv. 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size). |
| 239 | Centering and shuttering including strutting, propping etc. and removal of form for: i. Foundations, footings, bases of columns etc. for mass concrete. |
| 240 | ii. Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. |
| 241 | iii. Suspended floors, roofs, landings, balconies and access platforms. |
| 242 | Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth leveli. 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size |
| 243 | ii. 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) |
| 244 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level i. Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 245 | Dismantling old plaster or skirting, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 meters lead. |
| 246 | 12mm Cement plaster of mix: i. 1 : 4 ( 1 cement : 4 fine sand) |
| 247 | Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in : i. Cement mortar 1:6 ( 1 cement : 6 coarse sand |
| 248 | Demolishing stone rubble masonry manually/by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge: i. In cement mortar |
| 249 | Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 meters lead. |
| 250 | Extra for makig of structural steel work required to be re-erected. |
| 251 | Demolishing brick work manually/by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge: i. In cement mortar |
| 252 | Random Rubble masonry with hard stone in foundation and plinth including leveling up with cement concrete. Quarry Stone.i. Cement mortar 1:6 (1 Cement : 6 coarse sand) |
| 253 | Dry random rubble masonry with hard stone in foundation and plinth: i. With bond stone (Quarry Stone). |
| 254 | Providing and laying damp-proof Course 50 mm thick with cement concrete 1:2:4 (1 cement:2 coarse sand: 4 graded stone aggregate 20 mm nominal size) and curing complete. |
| 255 | Pointing on stone work with cement mortar 1 : 3 (1 cement : 3 fine sand) i. Flush/Ruled Pointing |
| 256 | Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level. |
| 257 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): i. First class kail wood. |
| 258 | Providing and fixing glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws (30mm thick).i. First class kail wood. |
| 259 | Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board (conforming to IS: 12823 Grade-I type-II) in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-incharge. I. Pre-laminated particle board with decorative lamination on both sides. |
| 260 | Providing and fixing aluminum tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : i. 100x10 mm |
| 261 | Providing and fixing ISI marked oxidized M.S. handles conforming to IS : 4992 with necessary screws etc. complete : I. 100 mm |
| 262 | Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. |
| 263 | Finishing with Deluxe multi surface paint system for interiors and exteriors using primer as per manufacturers’ specifications: i. Painting wood work with deluxe multi surface paint of required shade. Two or more coats applied @ 0.90litre/10sqm over an under coat of primer applied @ 0.75litre/10sqm of approved brand and manufacture |
| 264 | Finishing walls with water proofing cement paint of required shade: i. Old work (one or more coats applied @ 2.20 kg/10sqm) over priming coat of primer applied @ 0.80 liters/10sqm complete including cost of priming coat |
| 265 | Dismantling roofing including ridges, hips valleys and gutters etc., and stacking the material within 50 meters lead of : i. G.S. Sheet |
| 266 | Providing corrugated G. S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/vertical or curved surface)excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.i. 0.63 mm thick with zinc coating not less than 275 gram/m2 |
| 267 | Carriage of Materials by Mechanical Transport.a. Cement/Steel avg lead 1km. |
| 268 | a. Stone Soling avg lead 1Km. |
| 269 | b. Stone avg lead 1Km. |
| 270 | c. Sand avg lead 1Km. |
| 271 | d. Coarse Agg 40mm N/S avg lead 1Km. |
| 272 | e. Coarse Agg 20mm N/S avg lead 1Km. |
| 273 | g. Bricks avg lead 1Km Per 1000 Bricks |
| 274 | Hire charges of load carrier/mini truck for carriage of chemicals and other allied items/equipments (excl. pipes) from Divisional Store upto various sites & locations incl carriage of dismantled salvaged pipes(serviceable/unserviceable) from site to Divl. store incl. loading ,unloading & stacking charges.(to be paid as per gate pass trip). Complete job. |
| 275 | Replacement of defunct street lights by way of replacing of damaged Bulbs, wires, switches & other necessary accessories needed for making the light functional with 100 Watt LED flood light this also includes all leads & lifts complete Job. |
| 276 | Replacement of defunct street lights by way of replacing of damaged Bulbs, wires, switches & other necessary accessories needed for making the light functional with 50 Watt LED flood light this also includes all leads & lifts complete Job. |
| 277 | Engagement of Hydraulic Crane with driver and fuel Including haltage. complete job. |
| 278 | Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge (glazing, panelling and dash fasteners to be paid for separately.) i. For fixed portion a. Anodized aluminum (Anodized transparent or dyed to required shade according to IS:1868, minimum anodic coating of grade AC 15). |
| 279 | b. Powder coated aluminum (minimum thickness of powder coated 50 microns). |
| 280 | c. Polyester powder coated aluminum (minimum thickness of polyester powder coated 50 microns) |
| 281 | ii. For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately.) a. Anodized aluminum (Anodized transparent or dyed to required shade according to IS:1868, minimum anodic coating of grade AC 15). |
| 282 | b. 2 Powder coated aluminum (minimum thickness of powder coated 50 microns). |
| 283 | c. Polyester powder coated aluminum (minimum thickness of polyester powder coated 50 microns). |
| 284 | Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board (conforming to IS: 12823 Grade-I type-II) in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-incharge. i. Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side. |
| 285 | ii. Pre-laminated particle board with decorative lamination on both sides. |
| 286 | Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineerin-charge. (Cost of aluminum snap beading shall be paid in basic item.) i. With floating glass panes of 4.0 mm thickness (weight not less than 10.00 kg / sqm) |
| 287 | ii. With float glass panes of 5.0 mm thickness (weight not less than 12.50 kg / sqm). |
| 288 | iii. With float glass panes of 8 mm thickness (weight not less than 20.0 kg / sqm). |
| 289 | Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-incharge. I. Made of G.I. wire of dia 4 mm |
| 290 | Clearance of wet silt from Service Reservoirs through washout pipe / buckets. The job includes dewatering charges/tools/ tackles required for the job and disposal of silt as per site requirement / as directed by the Engineer-Incharge. This item also includes scaffolding / lighting arrangement if required at site.. (Complete Job). |
| 291 | Cleaning of wall, shaft and beds of the Service Reservoirs by washing, brushing twice and cleaning silt by spraying water by pumping equipment and chemical washing of surface by spraying chemical solution. This item also includes bathing of pores then clearance of all surface after chemical bath by washing with clean water and ensuring zero alkanity. This item also includes all types of tools and plants used for execution of job. Complete Job. |
| 292 | Repairing of pumps/motors by way of rewinding , inclduing replacement of damaged parts required .This item includes testing,all carriages including handling ,rehandling etc with trial run upto three months complete Job.a. 2HP |
| 293 | a. 3HP |
| 294 | b. 5HP |
| 295 | c. 40HP |
| 296 | Grinding,finishing& cleaning floor marble/bed complete using machine this item also includes cost of chemical used for cleaning. |
| 297 | Reparing of Refrigirator by way of servicing and change of defunct parts (complete Job). |
| 298 | Repairing of water Geyser.a. Heating element ALuminium made |
| 299 | a. Thermostat Autocut |
| 300 | b. Indicator lights |
| 301 | c. 3 pin plug 15 Ampere IS made |
| 302 | d. Copper Wire 2.5mm thick, 2.00Mtr. |
| 303 | e. Gyser bolts 4 No. MS |
| 304 | f. PVC connection length 450mm, 15mm. |
| 305 | h. Angle valve 15mm if IS make |
| 306 | Repairing of CCTV camera by way of servicing and changing defunct part ( complete Job). |
| 307 | Repairing of LED / LCD monitor of CCTV by way of servicing and changing defunct part (complete job). |
| 308 | Repairing of 40/50 hp starter by way of servicing and changing defunct part ( complete Job). |
| 309 | Repairing of 20hp camera by way of servicing and changing defunct part ( complete Job). |
| 310 | reparing of AC by way of servicing and changing defunct part ( complete Job) |
| 311 | reparing of 10mgd sign board by way of servicing and changing defunct part ( complete Job) |
| 312 | Repairing of Water Purifier by way of servicing and change of defunct parts (complete Job). |
| 313 | Gerneral Servicing/maintenance of 250KVA DG Set including replacement of lubricating oil filter,fuel filter,hose,hose clips.engine M-oil coolant ,& all others items required qith labour charges complete Job. |
| 314 | Providing & fixing of driving motors 3Hp for Bleaching Tanks with churning assembly Complete Job. |
| 315 | Providing refreshment to supervisory staff & departmental labour for prolonged/continuous operation of repair/ restoration/ maintenance work of pipelines. Complete job including packing with following Menu.i. Water Bottle One litre |
| 316 | i. Water Bottle 500 ml |
| 317 | ii. Juice 100ml of standard quality |
| 318 | iii. Boiled Egg/Omelete |
| 319 | iv. Biscuit standard Quality of 50g |
| 320 | v. Banana |
| 321 | vi. Tea Sugar each Cup |
| 322 | vii. Chicken Biryani |
| 323 | viii. Rice Plate with vegetables, Single piece meat for each person |
| 324 | VIIII. Tea Namkeen each Cup |
| 325 | VII. Tent 12”x12” with matting full for one night. |
| 326 | Supply and filling of 2nd class sand / stone dust around pipes at different spots including cost of material i.e. stone dust from available approved source including all carriages, leads and lifts upto the site of work including spreading of stone dust, levelling dressing and watering including compaction after each 15cms thickness in all respects. Complete Job. (Subject to actual quantities during execution). |
| 327 | Supply and Filling of trenches by GSB / Nallah Muck from approved source including all carriages upto actual site of work. The material shall be natural having durable particles graded from fine to coarse in a uniform combination with no boulders larger than 80mm in size. It shall not contain excessive quantity of loam. The item including ramming, consolidation in layers, charges of T&P, equipment’s etc. required for completion of job. (Subject to actual quantities during execution). |
| 328 | Welding of pipe / pipe fittings by way of engaging generator, welding set including all types of carriage involved. (Complete Job) (Subject to actual quantities during execution). |
| 329 | Providing of slowet vital chain block hoist 2 ton standard lifting height 6 meters running test load incl load chain having diameter 8 mm , weight 17.5 kg ( load chain : G80 chain , Hook : Deep forged high alloy steel, Gear : high standard gear steel , ) including carriage etc all complete job. |
| 330 | Boston brush cutter 4 stroke (heavy duty + attachments) BC -139F having 3 point blade , 80 teeth blade, tap N go ( nylon wire ), safety belt , safety guard , manual , tool kiten selected item weight 9.8 kgs , dimensions 166L X 33W centimeters as per engineer incharge. |
| 331 | Hire charges of commercial vehicle including POL alongwith comercial driver licensed.I. upto 10 Km per day |
| 332 | I. upto 20 Km per day |
| 333 | Beyond 20 km upto 50 Km per day |
| 334 | Providing and fixing double scaffolding system ( cup lock type ) on the exterior side of building/ structure, upto 25 mtrs height above ground level, including additional rows of scaffolding in stepped manner as per requirement of site, made with 40mm dia M.S. tube, placed 1.5 mtr.c/c, horizontal and vertical tubes joint with cup and lock system with M.s tube, M.S tubes Challis M.S clamps and stairs case system in the scaffolding for working platform etc. and maintaining it in a serviceable condition of execution of work of cleaning and/ or pointing and/or applying chemical and removing it their after the scaffolding system shall be stiffened with bracings, runners connecting with the building etc. where ever required. if feasible, for inspection of work at required location with essential safety features for the work men etc, complete as per directions and approval of Engineer-in-charge. |
| 335 | Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. (The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account) |
| 336 | Providing and fixing false ceiling at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceilingtiles of Size 595x595 mm of approved texture, design and patterns having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity < 0.043 W/m K as per ASTM 518:1991, in true horizontal level suspended on interlocking metal powder coated T-Grid of hot dipped galvanised iron section of 0.40 mm thick on Silhouette profile, rotary stitched double webbed white with 6mm reveal profile (white/black),comprising of main-T runners of size 15x42mm of length 3000 mm, cross - T of size 15x42 mm of length 1200 mm and secondary intermediate cross- T of size 15x42 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steelitems (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 22x19x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall S.S screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge. 31.21.1 With 15 mm thick integral densified micro edge light weight calcium silicate false ceiling tiles. |
| 337 | Providing, mixing and applying bonding coat of approved adhesive on chipped portion of RCC as per specifications and direction of EngineerIn-charge complete in all respect. a. SBR Polymer (@10% of cement weight) modified cementitious bond coat @ 2.2 kg cement per sqm of surface area mixed with specified proportion of approved polymer |
| 338 | b. Epoxy bonding adhesive having coverage 2.20 sqm/kgof approved make |
| 339 | Chipping of unsound/weak concrete material from slabs, beams,columns etc. with manual Chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of Engineer-In-Charge i. 75mm average thickness |
| 340 | i. 50mm average thickness |
| 341 | ii. 25mm average thickness |
| 342 | Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade, one or more coats on old work. |
| 343 | Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound) content less than 50 grams/ liter, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. i. Two coats |
| 344 | Finishing with Deluxe multi surface paint system for interiors and exteriors using primer as per manufacturers’ specifications: I. Painting wood work with deluxe multi surface paint of required shade. Two or more coats applied @ 0.90litre/10sqm over an under coat of primer applied @ 0.75litre/10sqm of approved brand and manufacture. |
| 345 | Hire charges for:I. core cutting/wall saw cutting machine along with operator, haltage complete job. |
| 346 | II. concrete drill/ hammer drill machine along with operator Complete Job. |
| 347 | III. brush cutter machine along with operator POL. |
| 348 | Wall paintings/writings on walls complete including cost of scaffolding wherever needed complete Job as per the direction of Engineer Incharge |
| 349 | Providing, mixing and applying bonding coat of approved adhesive on chipped portion of RCC as per specifications and direction of Engineerin-charge complete in all respect. (LMR)i. chipping of existingplaster from the wall and its removal and disposal upto 200m Surface preparationa) Filling of cracks, honeycombs, voids, and undulations, treatment of construction joints in RCC slab by way of cutting, applying bond coat and filling grooves of 25mmx25mm using cementitious ready mix Injection grouting using cementitious polymer modified mortar slurry, polymer reinforced covering of 75mm x 75mm will be made at the junctionc using nonshrink micro concrete, food grade chemicalApplication of waterproof coating on the prepared surface of the walls using high dispersion SBR latex ensuring higher mixing efficiency with water reduction for site batched mortars and waterproofing complete job |
| 350 | Hire charges of skilled M.S fabricator for fabrication job at site viz MS winch gate , bends , tees etc including cutting , welding complete job. |
| 351 | Clearing Snow (without frost) from Roads, manually; a. Snow depth upto 150 mm |
| 352 | a. Snow depth over 150 mm but upto 250mm |
| 353 | b. Snow depth over 250 mm but upto 350mm |
| 354 | c. Snow depth over 350 mm but upto 450mm |
| 355 | d. Snow depth over 450 mm but upto 550mm |
| 356 | e. Snow depth over 550 mm but upto 650mm |
| 357 | f. Snow depth over 650 mm but upto 750mm |
| 358 | g. Snow depth over 750 mm but upto 850mm |
| 359 | h. Snow depth over 850 mm but upto 950mm |
| 360 | i. Snow depth over 950 mm but upto 1050mm |
| 361 | Snow depth over 1050 mm but upto 1150mm |
| 362 | Steel cryst sign board with light , letters 150mm to 500mm in height . Complete job as directed by Engineer incharge . |
| 363 | Base for steel cryst sign board including frame , cabling , hooks, nuts , bolts . Complete job as directed by Engineer incharge . |
| 364 | Providing and fixing Waste pipe pvc 100mm dia . Complete job |
| 365 | Providing and fixing Waste pipe pvc 50/65mm dia . Complete job |
| 366 | Providing and fixing of steel window hook |
| 367 | Providing and fixing of rain water gutters ( parnals ). Complete job |
| 368 | Servicing/maintenance of sluice valve (150mm to 600mm dia ) by way of greesing , oiling , gland packing and replacement of washer if damaged . Complete job |
| 369 | Providing & installation of flex banner with the text & images printed without MS tubluar support/frame as per the directions of Engineer Incharge Complete job. |
| 370 | Providing & installation of flex banner with the text & images printed with MS tubluar support/frame as per the directions of Engineer Incharge Complete job. |
| 371 | Engagement of Hydraulic Excavator (L&T) with driver and fuel including haltage and transportation charges complete job. |
| 372 | Repairing of aluminium doors and windows fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. including cleat angle, Aluminum snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete |
| 373 | Clearance / removing of trash from intake and stage I sump by using buckets and other accessories . The job includes tools/ tackles required for the job and disposal of trash as per site requirement / as directed by the Engineer-Incharge. This item also includes scaffolding /safety gears / ladders / ropes etc . required at site.. (Complete Job). |
| 374 | Repairing of gas and electric by way of servicing and changing defunct part ( complete Job) |
| 375 | Repairing of printer by way of servicing and changing defunct part ( complete Job) |
| 376 | Providing and fixing of 50HP start delta starter with all necessary elctrical accessories etc . As directed by incharge engineer . Complete job |
| 377 | Providing and fixing of 20HP start delta starter with all necessary elctrical accessories etc . As directed by incharge engineer . Complete job |
| 378 | Unloading chemicals (Alum or Bleaching) by manual means from trenches and carrying the same into chemical store including stacking the same properly in rows upto any height as per the clarification of Incharge Incharge, sweeping the vehicles/floor. Please Enable Macros to View BoQ information |
