Tender For Construction Of Police Station Building Including Parking At Ground Floor & Site Development At Nagrota Bagwan, Distt. Kangra (Hp). [Sh: Civil And Electrical Works]., Nagrota-Himachal Pradesh

TDR : 55099980

Tender Notice
BOQ

16 Days Left

Nagrota , Himachal Pradesh

Tender Brief : Tender For Construction Of Police Station Building Including Parking At Ground Floor & Site Development At Nagrota Bagwan, Distt. Kangra (Hp). [Sh: Civil And Electrical Works].

Document Fees
₹ 1770 /-

EMD
₹ 1197327.0 /-

Tender Value
₹ 5.98 Crore /-

Submission Date
02-05-2026

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	Sub-Head : Earth Work
2	Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth, lead up to 50m and lift up to 1.5m,as directed by Engineer-in-Charge.
3	All kinds of soil
4	Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30 cm in depth, 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth, lead up to 50 m and lift up to 1.5m, as directed by Engineer-in-Charge.
5	Ordinary rock
6	Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.
7	All kinds of soil.
8	Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains not exceeding 1.5m in width or 10 sqm on plan including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50m.
9	Ordinary rock
10	Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m :
11	All kinds of soil
12	Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia
13	Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.
14	Extra for every additional lift of 1.5 m or part thereof in excavation /banking excavated or stacked materials.
15	All kinds of soil.
16	Supplying and filling in plinth with local fine sand under floors, including watering, ramming, consolidating and dressing complete.
17	Sub-Head : Concrete Work
18	Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :
19	1:2:4 (1 cement : 2 coarse sand(zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)
20	1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources)
21	Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor, etc., up to floor five level, excluding the cost of centering, shuttering and finishing :
22	1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)
23	1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources).
24	Centering and shuttering including strutting, propping etc. and removal of form work for :
25	Retaining walls, return walls, walls (any thickness) including attached pilasters, buttresses, plinth and string courses fillets, kerbs and steps etc..
26	Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation leveling & dressing & finishing the top smooth.
27	Providing and laying in position plum concrete with hard stone boulders in retaining walls etc up to all height and level, in required size and shape etc. with cement concrete of mix 1:3:6 (1 Cement : 3 Coarse sand : 6 Graded stone aggregate 40 mm nominal size) using 40 % plum / hard stone boulders of size 150 mm to 300 mm, excluding cost centring and shuttering all complete as per the direction of Engineer-in-charge.
28	Providing and fixing 110 mm dia P.V.C. pipe (working pressure 4Kg./Sqcm.) conforming to IS : 13592 type-A in retaining walls for use as weep holes, laid to required slope complete as per the directions of the Engineer- in- charge.
29	Filling with well graded stone boulders at the back of Retaining wall complete as per the directions of the Engineer-in-charge.
30	Sub-Head : Reinforced Cement Concrete
31	Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :
32	1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)
33	Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :
34	1:1.5:3 (1 cement : 1.5 coarse sand(zone-III)derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)
35	Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III)derived from natural sources : 3 graded stone aggregate 20 mm nominal sizederived from natural sources).
36	Reinforced cement concrete work in arches, archribs, domes, vaults, shells, folded plate and roofs having slope more than 15° up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III)derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources ).
37	Centering and shuttering including strutting, propping etc. and removal of form for all heights:
38	Foundations, footings, bases of columns, etc. for mass concrete.
39	Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.
40	Suspended floors, roofs, landings, balconies and access platform.
41	Shelves (Cast in situ).
42	Lintels, beams, plinth beams, girders, bressumers and cantilevers.
43	Columns, Pillars, Piers, Abutments, Posts and Struts.
44	Stairs, (excluding landings) except spiral-staircases.
45	Arches, domes, vaults up to 6 m span.
46	Vertical and horizontal fins individually or forming box louvers band, facias and eaves boards.
47	Small lintels not exceeding 1.5m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like.
48	Edges of slabs and breaks in floors and walls.
49	Under 20 cm wide
50	Cornices and mouldings
51	Weather shade, Chajjas, corbels etc., including edges.
52	Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete at all level
53	Thermo-Mechanically Treated bars of grade Fe-500D or more.
54	Smooth finishing of the exposed surface of R.C.C. work with 6 mm thick cement mortar 1:3 (1 Cement : 3 fine sand).
55	Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.
56	Extra for R.C.C./ B.M.C/ R.M.C. work above floor V level for each four floors or part thereof.
57	Making holes of 150mm dia and 100 to 200 mm depth in RCC slab by core cutting method or other suitable method for fixing SCI/ CI/ PVC pippes and sealing the joints with silicone adhesive and water sealant grout / white cement ro make water tight joint after fixing of pipes including scaffolding whereever requires all complete as per the direction of the Engineer-in-charge.
58	Sub-Head : Masonry Work
59	Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:
60	Cement mortar 1:6 (1 cement : 6 coarse sand)
61	Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :
62	Cement mortar 1:4 (1 cement : 4 coarse sand)
63	Cement mortar 1:6 (1 cement : 6 coarse sand)
64	Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.
65	Cement mortar 1:3 (1 cement :3 coarse sand)
66	Cement mortar 1:4 (1 cement :4 coarse sand)
67	Extra for half brick masonry in superstructure, above floor V level for every four floors or part thereof by mechanical means.
68	Extra for providing and placing in position 2 Nos. 6mm dia. M.S. bars at every third course of half brick masonry.
69	Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine sand).
70	Sub-Head : Cladding Work
71	Providing and fixing 18mm thick gang saw cut mirror polished premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.
72	Granite stone slab colour black, Cherry/Ruby red
73	Area of slab upto 0.50 sqm
74	Area of slab over 0.50 sqm
75	Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.
76	Granite work
77	Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin basedadhesive, including cleaning etc. complete.
78	Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/Granite / stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.
79	Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinalpartitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finishedsmooth.
80	Granite Stone of approved shade
81	Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.
82	Providing & laying cladding with brick tiles of size 220x70x20mm of approved make for wall lining up to 10 metre height, on the external face of brick wall on 12 mm cement plaster of mix 1 : 3 (1 cement : 3 coarse sand) and jointed with grey cement slurry @ 3.3 kg/sqm complete including pointing with white cement mixed with matching pigment all complete as per approved architectural drawings and direction of Engineer-in-Charge.
83	Sub-Head : Wood and PVC Work
84	Extra for providing frosted glass panes 5 mm thick (weight not less than 12.50 kg per sqm) instead of ordinary float glass panes 5 mm thick (weight not less than 12.50 kg per sqm) in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured).
85	Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.
86	35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.
87	25 mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. Piano hinges IS: 3818 marked with necessary screws.
88	Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded) (overall area of door shutter to be measured):
89	Rectangular or square
90	Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured).
91	Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.
92	Fixed to openings /wooden frames with rawl plugs screws etc.
93	Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws:
94	35 mm thick shutters.
95	with ISI marked M.S. pressed butt hinges bright finished of required size - Second class teak wood
96	Providing and fixing expandable fasteners of specified size with necessary plastic sleeves and galvanised M.S. screws including drilling holes in masonry work /CC/ R.C.C. and making good etc. complete.
97	50 mm long
98	Providing and fixing plywood 4 mm thick one side decorative veneer conforming to IS: 1328 (type-1) for plain lining / cladding with necessary screws, including priming coat on unexposed surface with:
99	Decorative veneer facings of approved manufacture.
100	Providing and fixing curtain rods of 1.25 mm thick chromium plated brass plate, with two chromium plated brass brackets fixed with C.P. brass screws and wooden plugs, etc., wherever necessary complete :
101	25 mm dia.
102	Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets :
103	25 mm dia (heavy type)
104	Providing and fixing ISI marked IS : 453 oxidised M.S. double acting spring hinges with necessary screws etc. complete (Copper oxidised as per IS 1378)
105	150 mm
106	Providing and fixing bright finished brass hasp and staple (safety type) with necessary screws etc. complete :
107	90 mm
108	Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers of approved quality with necessary screws etc. complete.
109	50 mm
110	Providing and fixing 50 mm bright finished brass cup board or wardrobe knob of approved quality with necessary screws.
111	Providing and fixing stainless steel handles transparent or dyed to required colour or shade with necessary screws etc. complete :
112	125 mm
113	Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.
114	Providing and fixing Stainless steel sliding door bolts transparent or dyed to required colour or shade with nuts and screws etc. complete :
115	250x16 mm
116	Providing and fixing Stainless steel tower bolts transparent or dyed to required colour or shade with necessary screws etc. complete :
117	250x10 mm
118	Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868)transparent or dyed to required colour and shade with necessary screws etc. complete.
119	Twin rubber stopper
120	Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or
121	metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound,jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture’s specification and direction of engineer in charge all complete.
122	75 mm overall thickness partition with 12.5 mm thick double skin fire rated board conforming to IS: 2095: part I
123	Providing and fixing 2nd class teak wood lipping/ moulded beading or taj beading of size 18X5 mm fixed with wooden adhesive of approved quality and screws/ nails on the edges of the Pre-laminated particle board as per direction of Engineer-in-charge.
124	Providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete.
125	Double strip (horizontal type)
126	Providing and fixing powder coated telescopic drawer channels 300 mm long with necessary screws etc. complete as per directions of Engineer-in-charge.
127	Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.
128	1.0 mm thick.
129	Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc.
130	After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod pf approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge.
131	Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per design requirements and conforming to IS: 3548 & IS:16231 shall be paid separately.
132	Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for:
133	(i) Sites with basic wind speed > 45 m/sec as per IS 875 - Part 3
134	(ii) Sites with structure height more than 20m for all wind speeds.
135	Three track three panels sliding window with two glazed & one wire mesh panels with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body.
136	Using R3 series with frame (98mm & above) x (40mm & above) & both glazed and fly screen sash (30mm & above) x (55mm & above) with zinc alloy (zamak) powder coated handle on every glazed panel along with multi-point locking system, (Height upto 1.8m).
137	Fixed window / ventilator without mullion / transom
138	Using R2 series with frame (39mm & above ) x (39mm & above). (Height upto 1.2 meter)
139	Ventilator Casement window single panel with or without fixed panel with S S. 304 friction hinges as per size and weight of sash, single point locking zinc alloy (zamak) powder coated handles.
140	Using R2 series with frame (39mm & above ) x (39mm & above) & sash /mullion (39mm & above) x (60mm & above). (Height upto 1.2 meter)
141	Providing and fixing stainless steel (SS-304 grade) friction hinges to the side/top hung uPVC windows, of approved quality, with necessary stainless steel screws etc. as per direction of Engineer-in-charge.
142	300 x 19 x 1.9 mm
143	Providing and fixing casement handle made of zinc alloyed (white powder coated) for uPVC casement window with necessary screws etc. complete.
144	Providing and fixing fly proof stainless steel grade 304 wire gauge with average width of aperture 1.40 mm in both directions with wire of dia 0.50 mm to uPVC windows, doors & ventilators all complete with uPVC beading as per manufacturer's specification and direction of Engineer-in-charge. (Note :- uPVC beading to be paid in basic frame item).
145	Providing and fixing glazing in uPVC windows, all complete with uPVC beading as per manufacturer's specification and direction of of Engineer-in-charge. ( Note :- uPVC beading to be paid in basic frame item). (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured).
146	6mm thick toughened glass .
147	Providing and fixing BWP Ply board conforming to IS: 710 of of Merino/ Greenply/ Century/Archid/Kitply , bonded with phenolformaldehyde synthetic resin in cupboards, shelves, shutters with necessary screws, nails and adhesive etc. all complete as per the direction of Engineer-in-charge
148	18mm thick
149	Providing and fixing 6mm thick BWP grade commercial ply of Merino/ Greenply/ Century/ Archid / Kitply , bonded with phenolformaldehyde synthetic resin in backing of cupboards, shelves, shutters with necessary screws, nails and adhesive etc. all complete as per the direction of Engineer-in-charge
150	6mm thick
151	Providing and fixing 3.00 mm thick acrylic transparent sheet in windows & vantilators,Doors etc. complete . The sheet shall be fixed using self drilling /self tapping screws and including cutting to size and shape wherever required.
152	Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).
153	Providing and fixing stainless steel stands of 75mm height for (heavy weight)Cupboard/ Kitchen Cabnet Legs with stainless steel screws etc. complete :
154	Sub-Head : Steel Work
155	Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.
156	Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:
157	Profile B - With Single Rebate
158	Fixing with adjustable lugs with split end tail to each jamb.
159	Profile D - With Douible Rebate
160	Fixing with adjustable lugs with split end tail to each jamb.
161	Providing and fixing mild steel round holding down bolts with nuts and washer plates complete.
162	Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.
163	In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.
164	Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).
165	Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows all complete with :
166	5.0 mm thick glass panes.
167	Sub-Head : Flooring
168	Providing and laying full body vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08%and conforming to IS : 15622 , of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete.
169	Size of Tile 600x600 mm
170	Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.
171	Glazed Vitrified tiles Matt/Antiskid finish of size
172	Size of Tile 600 x 600 mm
173	Providing and laying full body Vitrified tiles in different sizes (thickness to be specified by manufacturer) with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make in all colours & shade in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete.
174	Size of Tile 600x600 mm
175	Providing and laying Glazed Vitrified tiles polished finish (thickness to be specified by manufacturer) with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make in all colours & shade in skirting, riser of steps & dado, over 12 mm thick bed of cement mortar 1:3 (1cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete.
176	Size of Tile 600x1200 mm
177	Providing and laying full body vitrified tile in floor of minimum thickness 15 mm for parking area with water absorption less than 0.06% and conforming to IS: 15622, of approved make, brand and manufacturer, laid on 20 mm thick base cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.30 kg / sqm including grouting the joints with white cement and matching pigments etc. The slab must be cut with the zero chipping diamond cutter only. Laying of slab will be done with the help of notch trowel, wedge, clips of required thickness, vacuum cups for lifting, leveling system and rubber mallet for placing the slab gently and easily.
178	Size of Tile 300x300 mm
179	Filling the gap in between aluminium/ stone/ wood frame and adjacent RCC/Brick/ Stone/ wood/ Ceramic/ Gypsum work by providing weather/structural non sag elastomeric PU sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete, complying to ASTM C920, DIN 18540-F & ISO 11600
180	Upto 5 mm depth and 5 mm width
181	Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling /grouting and finishing complete as per direction of Engineer-in-charge.
182	Size of Tile 600x600 mm
183	Size of Tile 600x1200 mm
184	Sub-Head : Roofing
185	Providing and fixing plain multipurpose cement board(Hight pressure steam cured) with suitable screws for cement particle board in ceiling etc. complete (frame work to be paid seperatately).
186	6 mm thick Cement fiber board, Type-B, Category-III as per IS: 14862 : 2000
187	Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm ( + 0.05 %), total coated thickness with zinc coating 120 gm per sqm as per IS:277 in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.
188	Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05 %) total coated thickness, Zinc coating 120 gm per sqm as per IS: 277 in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :
189	Ridges / valleys plain (500 - 600mm).
190	Flashings/ Aprons.( Upto 600 mm)
191	Sub-Head : Finishing
192	12 mm cement plaster of mix :
193	1:6 (1 cement: 6 coarse sand)
194	15 mm cement plaster on rough side of single or half brick wall of mix :
195	1:6 (1 cement: 6 coarse sand)
196	Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement.
197	20 mm cement plaster
198	Neat cement punning
199	Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer, of required shade and colour all complete :
200	New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre
201	Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade
202	New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm)
203	Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :
204	Two or more coats on new work.
205	Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:
206	Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture.
207	French spirit polishing :
208	Two or more coats on new works including a coat of wood filler.
209	Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
210	Sub-Head : Road Work
211	Providing and laying 60mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.
212	Sub-Head : Sanitary Installations
213	Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required
214	Stainless Steel AISI-304(18/8) Orissa pattern W.C. pan of size 585x480 mm with flush pipe and integrated type foot rests
215	Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings andfixtures complete, including cutting and making good the walls and floors wherever required :
216	W.C. pan with ISI marked white solid plastic seat and lid
217	Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required :
218	Range of two half stall urinals with 5 litre P.V.C. automatic flushing cistern.
219	Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:
220	White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps.
221	White Vitreous China Flat back wash basin size 550x400 mm with single 15 mm C.P. brass pillar tap.
222	White Vitreous China Flat back wash basin size 450x300 mm with single 15 mm C.P. brass pillar tap.
223	Stainless Steel AISI-304(18/8) Wash basin 530x345 mm with single 15 mm C.P. brass pillar tap
224	Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.
225	Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :
226	Kitchen sink with drain board
227	510x1040 mm bowl depth 200 mm.
228	Kitchen sink without drain board
229	610x510 mm bowl depth 200 mm.
230	Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to European type W.C. of quality and make as approved by Engineer-in-charge.
231	Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.
232	Semi rigid pipe
233	32 mm dia
234	40 mm dia
235	Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.
236	Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.
237	Providing and fixing toilet paper holder :
238	C.P. brass
239	Providing and laying UPVC SWR pipes 110mm dia. [Type-B category] conforming to IS:13592-2013 of Supreme/ Diplast /Phenolex make, including jointing with suitable PVC adhesive complete as per the direection of Engineer in Charge.
240	Providing and laying UPVC SWR pipes fittings of Supreme/ Diplast /Phenolex make including jointing with suitable PVC adhesive complete as per the direection of engineer in Charge.
241	Bend 87.5 degree: 110 mm bend.
242	Door Bend 87.5 degree: 110 mm door bend.
243	Single tee without door: 110 x 110 x 110 mm.
244	Single tee with door: 110 x 110 x 110 mm.
245	Coupler : 110mm
246	Vent Cowl : 110mm
247	P-Trap 125x110mm
248	Floor Trap with SS grating 110x110mm
249	Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.
250	Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with a minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.
251	Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.
252	600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.
253	Providing and fixing PTMT shelf 440 mm long, 124 mm width and 36 mm height of approved quality and colour. Weighing not less than 300 gms.
254	Sub-Head : Water Supply
255	Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. : Internal work – Exposed on wall.
256	20 mm dia. nominal bore
257	25 mm dia. nominal bore
258	32 mm dia. nominal bore
259	40 mm dia. nominal bore
260	Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe including painting with anticorrosive bitumastic paint, cutting chases and making good the wall:
261	15 mm dia. nominal bore
262	20 mm dia. nominal bore
263	Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. : External work
264	32 mm dia. nominal bore
265	Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete :
266	25 to 40 mm nominal bore
267	Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :
268	25 mm nominal bore
269	32 mm nominal bore.
270	Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :
271	15 mm nominal bore
272	Providing and fixing uplasticised PVC connection pipe with brass unions :
273	45 cm length
274	15 mm nominal bore
275	Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :
276	100 mm diameter
277	Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work :
278	20 mm diameter pipe.
279	25 mm diameter pipe.
280	32 mm diameter pipe.
281	40 mm diameter pipe.
282	Providing and filling sand of grading zone V or coarser grade all- round the G.I. pipes in external work.
283	32 mm diameter pipe
284	Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work)
285	15 mm nominal bore
286	20 mm nominal bore
287	25 mm nominal bore
288	32 mm nominal
289	40 mm nominal bore
290	Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.
291	Circular tank
292	Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931:
293	15 mm nominal bore.
294	Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.
295	15 mm nominal bore.
296	Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.
297	15 mm nominal bore
298	Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.
299	15 mm nominal bore.
300	Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931
301	15mm nominal bore
302	Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge.
303	Providing and fixing 15mm dia GI Tank nipple of approved make and quality as per direction of Engineer-in-charge.
304	Sub-Head : Drainage
305	Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. Complete.
306	250 mm diameter
307	Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design:
308	250 mm diameter S.W. pipe
309	Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design :
310	180x150 mm size P type
311	With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
312	Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2coarse sand : 4 graded stone aggregate 20 mm nominal size),foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size), inside plastering 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design :
313	Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg(weight of cover 23 kg and weight of frame 15 kg) :
314	With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
315	Extra for depth for manholes
316	Size 90x80 cm
317	With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
318	Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) as per standard design :
319	With 20x20 mm square bar
320	Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality
321	M D - 10
322	Circular shape 500 mm internal diameter
323	Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.
324	With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
325	Constructing soak pit 1.20x1.20x1.20 m filled with brickbats including S.W. drain pipe 100 mm diameter and 1.20 m long complete as per standard design.
326	Providing and laying Non Pressure NP-4 class (Heavy duty) R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete
327	450 mm dia RCC pipes.
328	Sub-Head : Water Proofing
329	Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of :i) Ist course of applying cement slurry @ 4.4 Kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontalsurface. ii) IInd course of 20mm cement plaster 1:3 (1 cement : 3 coarse sand)mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface.iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7Kg. per sqm of area. iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 Kg/sqm.)
330	Providing and fixing GI Spouts in depressed portions 40mm dia and 60Cm long in Cement Mortar 1:4 (1 Cement: 4 Fine Sand) i/c making arrangement for smooth & efficient functioning of the spout as per the direction of the Engineer-in-charge.
331	ELECTRICAL COMPONENT SUB HEAD-I (Wiring)
332	Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required
333	Group B
334	Group C
335	Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required
336	Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required
337	Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 2 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required
338	Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required
339	2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire
340	4 X 1.5 sq. mm + 2 X 1.5 sq. mm earth wire
341	2 X 10 sq. mm + 1 X 6 sq. mm earth wire ( For GF)
342	4 X 4 sq. mm + 2 X 4 sq. mm earth wire (For Light DB)
343	4 X 10 sq. mm + 2 X 6 sq. mm earth wire (For Power DB)
344	Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.
345	20 mm
346	25 mm
347	Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/recessed steel/PVC conduit as required.
348	2x1.5 sq. mm
349	3x1.5 sq. mm
350	4x1.5 sq. mm
351	Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required.
352	Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.
353	Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 2 nos. of 3 pin 5/6 A modular socket outlet and 2 nos. of 5/6 A modular switch, connections etc. as required.
354	Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.
355	5/6 amps switch
356	15/16 amps switch
357	3 pin 5/6 amp socket outlet
358	6 pin 15/16 amp socket outlet
359	TV antenna socket outlet
360	Telephone socket outlet
361	RJ-45 Jack with Cat 6 One Module
362	Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.
363	1 or 2 Module (75mmX75mm)
364	4 Module (125mmX75mm)
365	8 Module (125mmX125mm)
366	12 Module (200mmX150mm)
367	Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.
368	1 run of cable
369	2 run of cable
370	Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.
371	1 run of cable
372	Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, Unarmored Telephone cable in the existing surface/ recessed steel/ PVC conduit as required.
373	2 Pair
374	S/Fixing hexagonal fan box of size 150 mm dia made outof 16 SWG MS sheet including 12mm dia MS rod in the U shape with its vertical legs bent horizontally at the top at least 19 cm on either side and bound to the top reinforcement of the roof at the time of casting i/c S/F 3 mm thick phenolic laminated sheet at the bottom complete as reqd.
375	Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.
376	SUB HEAD-II (Distribution System)
377	Supplying and fixing following way, vertical type smart TPN, sheet steel, MCB distribution board, 415 volts having provision for MCCB as incomer, on surface/ recess, complete with metal door, tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCCB/ RCCB/ Isolator)
378	8WAY (8+8+8) Double Door ( Make L&T, Model:DTVTL008DD )
379	Supplying and Fixing Four pole, 125A MCCB with Fixed Thermal-Fixed Magnetic Release, breaking capacity 10KA at 415V with With Spreader Links for interconnection in the existing vertical DB i/c making interconnection etc as required. (M/s Lauritz & Knudsen , Model-DY125U 125A 10kA FTFM -EM90984OOLO or equivalent similar superior make)
380	Supplying and fixing following way, horizontal type SPN / TPN, sheet steel, Smart MCB distribution board, 240/ 415 volts, on surface/ recess, complete with metal door, tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/ RCCB/ Isolator)
381	8 Way SPN Double Door (Make& Model- Lauritz& Knudsen Model-DTSPN008GD-Tripbox NXT)
382	12 Way SPN Double Door (Make& Model- Lauritz& Knudsen Model-DTSPN012GD-Tripbox NXT)
383	6 Way TPN (8+18) Double Door ( Make& Model- Lauritz & Knudsen Model-DTTPN006GD-Tripbox NXT)
384	Supplying and fixing following rating, 240/415 volts, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.
385	5 amps to 32 amps, 240 volts Single pole.
386	Double Pole 32 amps
387	63 amps, 415 volts Four pole.
388	63 amps, TP MCB
389	S/F Following rating MCB power protected unit suitable for operation on 230V single phase AC supply complete with all accessories i/c making interconnection etc as required.
390	20A ( For Air Conditioning Units)
391	Supplying and fixing 25 Amps., double pole, (single phase and neutral), 230 volts, residual current circuit breaker (RCCB), having a sensitivity current up to 30 milli amperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.
392	Supplying and fixing 63 Amps., four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current up to 30 milli amperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.
393	Supplying and fixing Adaptor Box(s) fabricated out of 16 SWG M.S. sheet complete with cutting, welding, painting, sign writing etc. all as required.
394	Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.
395	SUB HEAD-III ( Earthing))
396	Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories,and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. (For Electrical & Lightening Arrestor Earth)
397	Supplying and laying 25 mm X 5 mm G.I strip on surface or in recess etc as required.
398	Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc.as reqd
399	Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required. Please Enable Macros to View BoQ information

Tender Documents

SR No	FileName	File Description
1	Click here to download tender document	Tender Documents
2	Click here to download tender document	Tender Documents
3	Click here to download tender document	Tender Documents

Also Visit

Tenders

Himachal Pradesh Tenders

Electrical Industry Tenders

Electrical Work Tenders

Electrical Maintenance Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Construction Of Police Station Building Including Parking At Ground Floor & Site Development At Nagrota Bagwan, Distt. Kangra (Hp). [Sh: Civil And Electrical Works]., Nagrota-Himachal Pradesh

Tender Documents

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Construction Of Police Station Building Including Parking At Ground Floor & Site Development At Nagrota Bagwan, Distt. Kangra (Hp). [Sh: Civil And Electrical Works]., Nagrota-Himachal Pradesh

Tender Documents

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us